Search Documents

By James Hyslop

MECHANIZATION of American coal mining continues to make rapid progress. Economic pressure will compel abandonment of manual methods wherever possible and will also provide the incentive needed for the improvement of machines and mining systems. However, rapid progress may be made along strictly technological lines and at the same time much slower progress in approaching maximum productivly and efficiency. One can well ask, just how efficient are mechanized mines, and to what extent is productivity affected by the mental attitude of management and workers?

Jan 1, 1946

By J. N. Ong

The oxidation of tantalum is assumed to occur by four simultaneous first-order chain reactions; solution of oxygen in the metal, nucleation and growth of a suboxide phase at the metal surface and two phase boundary processes which give rise to two different modifications of Ta2O5. A rate equation is then formulated which accounts for all principal details of oxidation behavior, unifies and correlatss the results of the principal investigations, and expresses the rate as a function of pressure, temperature, and time. For purposes of practical application, the expressions: may be used below and above 700T respectively to determine the regression rate of tantalum in cm per hr, where T is to be expressed in "K and P in atmospheres pressure of oxygm. The equations will reproduce within a factor of two all reported experimental rates in the temperature range 475" to 1400°C and pressure range 0.000026 to 40.8 atm 0. 1 HE oxidation kinetics of tantalum have been investigated thoroughly in the temperature range 50" to 1400 and pressure range 1.32 x l0-' to 40.8 atm pressure of 0,and as a result, the principal features of the oxidation of tantalum are known and have been described in considerable detail. The exposition of the characteristics of the behavior of tantalum in oxygen has been largely descriptive, with considerable attention being devoted to elucidating the structure, composition, and morphology of the resulting oxide products. The weight change vs time results have usually been reported graphically. With the exception of the linear rate below 700 C and the process of diffusion of interstitial oxygen into the metal,6'9 no effort has been made to characterize the reaction rates in functional form. It is the purpose of this paper to demonstrate that when the fundamental principles of chemical kinetics are rigorously followed, the results of the principal investigations will be correlated and unified and the oxidation rale may be expressed as an analytic function of pressure, temperature, and time. In addition to accounting for the temperature and pressure dependency of the oxidation rate, the following minor features will be accounted for as a result of the basic analysis: the initial period of nonline-arity in rate at low temperatures, which decreases with increasing temperature;3'5'7 the rate vs temperature cusps obtained at constant pressure"5 the concentration gradient of oxygen interstitially dissolved in the metal.5'7 The analysis will also be consistent with the overall chemistry of reaction and with all visual, microscopic, and X-ray observations. DEVELOPMENT OF RATE EQUATION As a fundamental basis for the treatment of metal-oxygen reaction kinetics, it will be regarded that the rate of reaction is determined by the concentration and not the activity or chemical potential. It is further assumed that all metal-oxygen reactions are first order complex chain reactions" whose rate is dependent on the concentration of an intermediate species which is a complex function of the oxygen concentration, or oxygen pressure, only. The basic rate equation is therefore: is the weight of oxygen consumed by the reaction, A is that portion of the area of the metal over which the reaction is occurring (cm2), t the time (sec), kf the rate constant for forward reaction, C the intermediate species concentration and f '([Oz]) and f (Po,) are complex functions of oxygen concentration and Oxygen pressure respectively. Reverse reactions may usually be neglected in metal-oxygen systems since a large negative free energy generally accompanies these reactions. Eq. [I] takes different forms when the rate of reaction is controlled by diffusion into or through a phase or at a phase boundary. For diffusion into the metal phase, the rate is given by1' Di is the diffusion coefficient of species diffusing into the metal phase (cm2/sec), and Q is the corre-

Jan 1, 1962

SINCE I have mentioned the art of alchemy in. many parts of this treatise of mine, especially when 'came to the description of the practice of various operations,* I do not here intend to argue as to whether it may be called true or not. But in case it is true, inasmuch as it is seen in operation to be a result dependent on the actions and virtues of fires, I should not pass by in silence without speaking at all of this art here, nor would I wish to do so, especially since I think that you do not really know what it is except in so far as common report is heard everywhere to the effect that whoever carries it to completion makes silver and gold with it. Because of this belief, many seek it with much time, labor, and expense, as I know you have often heard related, if not elsewhere, by me in the chapter on gold that I have written in this volume. Now do not think that I wish to teach you this art here, for I am one of those who do not know it. Therefore I shall tell you here, so that you may know more, only. that those workers who so eagerly follow after and seek it proceed by just two pathways. One is that which takes its enlightenment from the words of the wise philosophers, by means of which they think to attain it. This they call the just, holy, and good way, and they, say that in this they are but imitators and assistants of Nature, indeed, manipulators and true physicians-of .mineral bodies, purging them of superfluities and assisting them by augmenting their virtue and freeing them from their defects. In this way they sometimes proceed to corrupt these bodies in order to be able to separate the elements they contain so as to reduce them, if possible, to their primary materials, as they call them, or sometimes they convert them into new substances by means of this art or by adding another spirit different from the first one. Thus they seek in this way to bring these materials to a certain point of corruption or to a separation of elements, or to remove or add spirits to things, or to make coarse materials subtle and sometimes to make subtle materials coarse. Therefore, as you can understand, these persons, with bridle broken, run a circular track night and day, without ever having rest; and surely I do not know whether anyone has ever arrived at the desired goal. Nevertheless, even though the goal of this art were emptiness, as many

Jan 1, 1942

By R. E. Collins, Paul B. Crawford

Potentiometric model studies have been made of ertically fractured reservoirs. All fractures originated at he well and extended into the reservoir for various distances. Studies were made to determine the areal sweep efficiencies for line-drive patterns. The areal sweep efficiency for the unfractured system studied war 70.6 per cent. It was found that if the vertical fracture war paralIel with the direction of flood, the areal sweep efficiency may be considerably reduced, approaching zero in some instances. If the fracture was at right angles to the direction of flood, the areal sweep efficiency may be greater than that for the unfractured system. The sweep efficiency depends on the length and orientation of the fracture and direction of the flood. It is concluded that considerable effort should be made to determine the nature and direction of fractures before initiating a flooding program. Such information is required if the maximum sweep efficiency is to be obtained and channeling is to be reduced to a minimum. INTRODUCTION The recent development and application of fracturing techniques to petroleum reservoirs has served to focus considerable attention on the effect such fractures may have on secondary oil recoveries. The opinion has been expressed that fracturing may not alter appreciably the water flooding possibilities. Others have thought that channeling may occur and that the creation of fractures may serve to substantially reduce the possibilities of conducting a successful water flood in the reservoir The purpose of this study was to obtain quantitative estimates of the effect of vertical fractures on the areal sweep efficiencies of line-drive flooding patterns. In presenting this work on vertical fractures, it is not to be inferred that the present fracturing techniques result in producing a vertical fracture. The types of fracture which are created are not known with certainty in every case. Some are believed to be horizontal, others inclined along bedding planes, and some data indicate vertical fracturing. Each fracture will probably exert a different influence on the sweep efficiency of the secondary recovery program; consequently each fractured well should perhaps be considered as a separate problem, requiring a careful analysis. Preliminary work on the effect of fractures on producing capacity of a well indicated that for practical purposes many fractures may be treated as having a nearly infinite permeability This assumption appears to be valid in some instances where the permeability of the fracture is only 10 or 100 times greater than the permeability of the matrix. It is known to depend on the type, orientation and length of the fracture. In realization that fractures of only 0.01 in. width have calculated permeabilities near 5,000 darcys, it is believed that many fractures may be considered as of near infinite permeability without incurring serious error. Primarily for this reason this study was made with fracture analogs of very great permeability compared to the matrix. FRACTURED SYSTEM ANALOG The pattern sweep efficiencies reported here were obtained with the aid of a potentiometric model. The application of this type model for solving reservoir problems has been described in the literature.1,2,3 The electrolyte reservoir was 20 in. wide by 30 in. long by approximately % in. deep. The liquid depth was constant, which corresponded to a constant permeability-feet product from the injection to the production well. The electrolyte reservoir was built to correspond to a unit in the line-drive pattern shown in Fig. 1. This figure shows part of an infinite array of wells having alternate rows of fractured and unfractured wells. The area within the dashed rectangle shows the area generally studied in the model. In using the model to represent a fractured system, a thin strip of copper was soldered to the well or wells and the length and orientation of the strip was made to conform to the vertical fracture under consideration.

Jan 1, 1955

By HAROLD E. WHITE

LONG before the Stone Age, when man first sought shelter where there-were no natural shelters, such as caves and clefts in the rock, he uprooted trees and planted them upside down so that the roots formed the roof. By selecting trees whose roots grew out in a horizontal direction and; by planting these trees close enough - together, a crude shelter was formed. He then took mud, formed a plaster and covered over the' roots. Later the walls were made by using sticks and twigs and plastering between them. It is natural then, that he wiped his muddy hands on- his own hairy body and soon found that the mud was difficult to remove when, dry. It is due, to this discovery that we mix animal hair in 'our modern plaster to increase its strength. The use of fibrous asbestos in some refractory cements has followed this same principle.

Jan 1, 1929

By I. A. Lesk

The various materials utilized in the construction of integrated circuits, and the resultant materials interfaces, are discussed with emphasis on a materials system that is compatible with all types of integrated circuits and minimizes the number of different interfaces. Problems with interfaces may originate in the silicon, on its surface, and between other materials within the integrated-circuit package independent of the silicon. ThE difference between integrated-circuit theory and practice may generally be spelled out in terms of the difficulties in fabricating a desired structure. There are, of course, problems in forming the requisite materials, of the necessary composition and geometry, where needed. A distinct class of problem, however, is associated with interfaces— generally between different materials, but occasionally between regions of the same material. We require that each interfacial system perform its proper electrical, mechanical, and thermal function, and do so in an unchanging manner with time under the most severe operating conditions. In a practical sense, we deal in nonideal systems, such that it is generally not possible to form an interface exactly the way it was intended, even if we allow for a knowledge of the practical limitations of the fabrication system. Another way of looking at this situation is to realize that, when we form a group of interfaces under apparently the same experimental conditions, there are often differences of important consequence between them. Very high-magnification pictures, such as are obtained by an electron microscope, reveal fine structure that often differs over the area of a given sample, as well as from sample to sample. Low-magnification pictures look better, but don't eliminate the problem. The trend towards integrated circuits, and away from circuits fabricated utilizing separate components, is very strong in many areas of electronics. A typical silicon monolithic integrated circuit, still in place in the wafer on which it was fabricated, is shown in Fig. 1. The increased reliability which is being experienced through the use of integrated circuits can, to a large extent, be credited to the reduced complexity of the interface system that is present in the electronic system. A glance at Fig. 1, however, with all of its epitaxial and diffused p-n junctions, and interconnect system, shows that interfaces have been far from eliminated. Fig. 2, depicting a schematic cross-sectional view of a (partial) typical integrated circuit, illustrates in detail the numerous interfaces that occur in this type of structure. Besides the individual circuit elements, there are interfaces for isolation, and, Fig. 3, even a crossover requires a series of interfaces. What has been accomplished, however, irrespective of whether or not the total number of interfaces in the circuit is increased or decreased, is that the variety of interfaces is very much reduced. This is because there are fewer materials involved. Since the expense incurred in an R & D program to improve reliability is pretty much directly proportional to the variety of interfaces involved, it is economically advisable to work with integrated circuits for highest reliability. That is not to say that circuits built using standard components could not be made as reliable as integrated circuits, but that the expense involved because of the more complex over-all interface system would be much greater. Although electronic performance utilizing integrated circuits with all silicon elements (i.e., transistors, diodes, resistors, capacitors) is adequate for many applications, there are numerous instances where thin-film passive elements must

Jan 1, 1965

By L. A. Wilson, N. H. Harrison, R. R. Clay, R. L. Reed. D. W. Reed

Experiments have been performed in a linear near-adiabatic system for the purpose of extending data on reverse and forward combustion from atmospheric pressure to 1,000 psig. Results obtained from reverse combustion appear to conform qualitatively with the existing description of the process when reaction kinetics are suitably modified to account for the increase in pressure, i.e., increasing tbe pressure decreases the peak temperature and increases the combustion zone velocity. Forward combustion appears to be a fuel dominated process wherein peak temperature and combustion zone velocity are not very sensitive to changes in pressure. The moderate effects of pressure that do exist at low flux virtually disappear at high flux providing all oxygen is consumed. With this provision. increasing the pressure decreases the frontal velocity and increases the peak temperature. Results me shown graphicaIIy which demonstrate the effects of presswe on peak temperature, rate of advance, oil recovery, air/oil ratio, carbon oxides produced and temperature distributions. INTRODUCTION Numerous field tests of oil recovery using the technique of underground combustion are now in progress. Operating pressures used are always substantially in excess of atmospheric pressure. Nevertheless, the literature contains no laboratory data pertaining to the effects of pressure except for those of Martin, Alexander and Dew.1 Unfortunately, these data appear to reflect heat losses which may have obscured some of the effects of increased pressure. The underground combustion processes are exceedingly complex, and general concepts relating to them have necessarily been described in relatively simple terms. Particularly with regard to forward combustion, the interaction between multiphase fluid flow, heat transport and various rate mechanisms is so involved that to date a rigorous treatment is not available. In this paper a linear near-adiabatic system is described which was found capable of operating at pressures up to 1,000 psig and temperatures of at least 1,100 F. Using this equipment, experiments on both forward and reverse combustion were accomplished at elevated pressures and the data presented as a function of air flux or temperature. It will be assumed that the reader is familiar with the papers of Wilson, Wygal, Reed, Gergins and Henderson on forward combustion and that of Reed, Reed and Tracht3 on reverse combustion, so that it is not necessary to repeat the details of the two processes. EQUIPMENT AND PROCEDURE It was decided to study the effects of pressure over the interval 0-1,000 psig using a near-adiabatic system. Since satisfactory operation of such a system requires very thin tubing walls, it proved necessary to insert the entire combustion tube and heater assembly into a high pressure jacket in such a way that the internal tube pressure could be counterbalanced by pressurizing the annulus. This meant that the numerous heater and thermocouple wires had to pass through gas-tight seals that required considerable effort to maintain effective. An unexpected difficulty arose in connection with the nature of the annulus pressuring gas. It turned out that the composition of this gas critically affected the functioning of the adiabatic control system. Operation of the equipment at elevated pressures was not particularly difficult. The problems that did arise were a direct consequence of the large numbers of connections and seals involved. EQUIPMENT The equipment consisted of the combustion tube which fitted within the pressure jacket. This jacket was in turn mounted on a wheeled carriage which facilitated movement and provided for rotation of the

By John H. Schemel

Large Zircaloy-2 hammer or press forged bars did not exhibit the uniform excellent corrosion resistance to steam normally expected of the alloy in wrought form. Weight gains of coupons cut from forged bars were 40 to 60 mg per sq dm compared to the 28 mg per sq dm obtained on hot rolled sheet and strip. The mechanism of this corrosion and its relation to microstructure is discussed. After these observations, a solution heat treatment followed by rapid cooling was tried on coupons from eight heats of forged bars. The basket-weave structure resulting from the quench did not show agglomeration of intermetallic compounds. These coupons showed uniformly good corrosion resistance with weight gains very close to the 28 mg per sq dm expected of Zircaloy-2 after the 14-day steam test. A large forging was solution heat-treated and tested for structure, mechanical properties, and corrosion resistance. Corrosion resistance was excellent and uniform throughout the section. The normally anisotropic mechanical properties were changed to completely iso-tropic. Strength levels were raised while there was a small loss in ductility at the service temperature. Tempering of the quenched structure below the ß transus did not improve the ductility at the test temperature of 600°F. ZIRCALOY-2 end caps for nuclear fuel elements Zircaloy-2 is an alloy of 1.5 pct Sn, 0.1 pct Fe, 0.1 pct Cr, and 0.05 pct Ni, balance hafnium-free zirconium patented by Westing-house Electric Co. used in pressurized water reactors are machined from large hammer-finished forged bars. The bars forged for this application range from 3 1/2 in. to 7 1/2 in. squares. One of the tests used to evaluate Zircaloy-2 for this service is a 14-day exposure to very high-purity steam at 75oF and 1500 psi pressure. Normally wrought products will exhibit a black lustrous film of zirconium oxide after the test and show a weight gain of approximately 28 mg per sq dm. Coupons representing the forged bars exhibited a wide variety of corrosion results ranging from acceptable black coupons to some covered with white crystals of zirconium oxide that had weight gains of nearly 100 mg per sq dm. One of the most common effects was a white corrosion product that looked like a stain to some observers and the outline of massive metal grains to others. Very careful specimen preparation prior to the corrosion test did not affect the result and metallographic examination did not reveal a structural feature of a size and shape that would correlate with the corrosion product. In addition to the relatively poor corrosion resistance, the forged product was not as ductile as desired. The problem of obtaining uniform and more acceptable properties in these heavy-forged sections seemed to be a function of the microstructure of the metal and, in particular, the distribution of the intermetallic compounds. None of the four alloying elements however are appreciably soluble in a zirconium and are present as compounds which usually appear scattered randomly throughout the structure. Moudryl showed that the distribution of these intermetallic compounds in Zircaloy could be related to a ostringero corrosion failure. Grozier et al. discussed another structural defect that causes a similar corrosion effect. In this case, an elongated gas-void was determined to be the cause. M. L. Picklesimer held in his discussion of the Grozier paper that at least a part of the observed =stringersn were caused by the distribution of the intermetallic compounds. He proposed a

Jan 1, 1962

By John R. Keith

Lead and zinc contents of elm, maple, and oak trees and of soils in which the trees grew were determined in samples from the Upper Mississippi Valley mining district, and from an area outside but contiguous to the district. The lead and zinc analyses of plant materials served to differentiate the mineralized and nonminer-alized areas. Stems contained about two times as much lead and about two to five times as much zinc as did leaves taken from the same stems. Lead and zinc analyses of all soil horizons could be used to differentiate between the two areas. Soils at most sample sites in the mineralized district seemed to be more reliable than plants for geochemical prospecting and are a more practical sampling medium. Soil samples from areas with thick loess cover, however, failed to indicate the presence of mineralized bodies whereas tree samples from the same sites contained anomalous amounts of lead and zinc. It is suggested that in areas of thick loess cover, plant samples could be used in prospecting for lead and zinc. The important part that plants play in the cycling of elements through the soil horizons is well-known. The concentration of elements in the upper soil horizons by the action of plants has been called the Goldschmidt enrichment principle.' The fact that plant species vary greatly in their ability to concentrate particular elements in their tissues is also well-known.' Agricultural literature has dealt extensively with relationships of the major nutritive elements in soils and plants3 The extent, however, to which plant actions cycle the minor nutritive and the nonmetabolic elements in the soil has not been adequately investigated. Lead is non-nutritive and toxic to plants, whereas zinc is a micronutrient in low, but toxic in high, concentrations.4 This report presents the results of a biogeochemical study concerned with the amounts of lead and zinc in some plants and soils that occurred both within and adjacent to the Upper Mississippi Valley lead-zinc district. Field work for this study was done in the summers of 1961 and 1962. SAMPLE TARGETS AND CHEMICAL ANALYSES Geologic and physiographic descriptions of' the district have been made by Heyl 5 and several other authors in a series of U.S. Geological Survey (USGS) reports and quadrangle maps.6-I Sedimentary rocks, mostly dolomite, limestone, shale, and sandstone, of Cambrian, Ordovician, and Silurian age predominate in the area. Mineral deposits are of the vein and cavity-fill type; the principal ore minerals are galena and sphalerite. Vegetation of the area was characterized by Curtis1 6 as southern hardwood forest interspersed with patches of oak savanna and prairie. Plant genera typical of the eastern United States Temperate Zone, including ash, cherry, dogwood, elm, hackberry, hickory, maple, oak, and other woody and herbaceous genera, are present. The natural vegetation has been greatly modified by agricultural, logging, and mining operations. The species of the original flora are present, but not in their former relative abundance. Soils of this district belong, for the most part, to the Brunizem and Gray-Brown Podzolic great soil groups. The Brunizems are the soils developed under prairie vegetation.'' The Gray-Brown Podzolics are the soils developed under deciduous forests,18 They are derived from both bedrock and from loess parent materials, and

Jan 1, 1970

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

It is known that stoichiometric NiTi transforms to a structure of lower symmetry near room temperature. The present investigation deals primarily with the changes in the electrical and magnetic properties which occur at the transformation. The effects of composition and various heat treatments on electrical properties are also discussed. In recent investigations by Purdy and Parr,' Wang et a1.,2 Dautovich and Purdy,~ Dautovich et a1.,4 and the authors, ~,' NiTi has been observed to undergo a martensitic phase transformation from the ordered CsCl (B2) structure to one of lower symmetry. The crystal structure of the low-temperature modification is still not completely worked out. This transformation occurs near room temperature for the stoichiometric composition. The thermodynamic, elastic, crystallographic, and microstructural characteristics of this transformation for some compositions have been previously reported.'-= In the present investigation, the changes in the electrical transport properties and magnetic susceptibility of NiTi when it undergoes the martensitic phase transformation have been measured. The approximate composition range covered is 48 to 52 pct Ti.* *All compositions are given in atomic percent._____________________ EXPERIMENTAL PROCEDURES AND RESULTS 1) Sample Preparation. The NiTi alloys were prepared from iodide titanium (>99.92 pct Ti) and vacuum-premelted carbonyl nickel (>99.95 pct Ni) by repeated arc melting under gettered argon and casting in a water-cooled copper mold. After the cast buttons were hot-forged at 800" to 950°C, the oxidized surface was removed by grinding and etching. Samples were cut from the worked polycrystalline buttons. After fabrication, the samples were annealed 1 hr at 900°C and water-quenched. The composition of the alloys was assumed to be the same as in the initial feed. This assumption was supported by material balance checks on 100-g arc-melted buttons which demonstrated quantitative recovery to within k0.02 pct. The oxygen content of the alloys was '150 ppma (weight) and the carbon content was 30 to 50 ppm. 2) Electrical Resistivity and Hall Effect. The electrical resistivity was measured over the composition range 48 to 52 pct Ti for temperatures varying from 4.2"K to 900°C. The high-temperature and many of the low-temperature experiments were carried out using conventional 4-probe dc techniques.7 The Hall coefficient and ac resistivity were measured at 20 cps using the apparatus shown schematically in Fig. 1. The equipment is basically an ac potentiometer: The resistive or Hall voltage of the sample is balanced by a comparison voltage provided by a dividing network across a standard series resistance. The off-balance signal is amplified by a Tektronix 122 amplifier and detected by a Princeton Applied Research (PAR) phase-sensitive detector. The precision of the resistivity and Hall coefficient measurements is i0.1 and i3 pct, respectively. The uncertainty in the data is increased by i2 pct from the precision limits because of uncertainty in dimensions and possible end effects. The temperature dependence of the electrical resistivity and Hall effect for a stoichiometric (50.0 pct Ti) NiTi sample are illustrated in Fig. 2. Above 75"C, this sample has essentially the B2 structure, while below about 0°C it is completely in the low-tempera-

Jan 1, 1968

By Nicholas J. Grant, Rolf Nordheim, Bill C. Gissen

The system Cb-Re was examined in detail utilizing pure metals, careful melting techniques, and heat treatments. Metallographic and X-my methods were utilized for phase identification. In addition to soli-dus determinations, the composition limits and mode of formation of the intermetallic compounds 0 and X were determined. The binary constitution diagram Cb-Re has been the subject of a number of investigations.'-7 Two intermetallic phases have been described and tentative diagrams have been proposed. It was the aim of this investigation to obtain a complete and more accurate diagram through the use of purer alloys and improved techniques. The diagram worked out by Knapton7 was published after our experiments were concluded. EXPERIMENTAL METHODS The starting materials were Re powder of 99.95 pct purity, supplied by the Chase Brass and Copper Co., and Cb rondelles of 99.6 pct purity, supplied by the Electro Metallurgical Co. Typical analyses are given in Table I. The alloys were prepared from compacted Re powder and Cb rondelles; for critical compositions master alloys were used. The melts varied from 5 to 50 g and were melted nonconsumably in an Heraeus arc furnace, under ti-tanium-gettered laboratory grade argon. It was necessary to invert the buttons and remelt, followed by crushing and further remeltings, the number of which depended on the nature of the fracture of the alloy. The weight of each alloy was carefully checked after each melting operation. It was found that significant weight losses occurred only when loose Re powder was used. These losses amounted to a maximum of 3 wt pct in such instances, but did not occur after the charge was once molten, regardless of the composition. Typical loss of weight after 4 remelts, including crushing, amounted to 0.2 wt pct. Oxygen pickup during successive melting cycles did not appear to be significant, since the weight gain values never exceeded 0.01 wt pct. Control of the composition of the alloys was not too difficult; however, the problem of homogenization was a far greater one. Optimum alloying conditions were finally achieved by a combination of master alloy production and repeated crushing and remelting cycles. The compositions of the alloys utilized to determine the constitution diagram are listed in Table 11. The weight balance method was used ultimately as the sole analytical method, since repeated checks indicated that it was accurate to 0.2 pct, if the weight losses were small. The results were double-checked by a metallographic study of the homogeneity of the samples, since this was presumed to be the more serious factor. Heat treatments at 1200°C or lower were accomplished by sealing the specimens in Vycor tubes, heating in a Globar furnace, followed by air cooling. This was considered to be an adequate quench because of the very low temperatures involved. For temperatures of 1200" to 1900°, alloys were homogenized and heat treated in a tungsten-filament resistance vacuum furnace. From 1900" to 2750" a tantalum-tube resistance furnace was utilized, operating under a vacuum of 105 mm Hg. The temperature measurements up to 1200" were made by means of platinum-platinum 10 pct Rh thermocouples, with an accuracy of 5°C. For temperature measurements greater than 1200°C, optical pyrometers were used. They were calibrated against a standardized instru-

Jan 1, 1962

By H. Larson, J. Chipman

The ferrous and ferric oxide concentrations of slags, expressed as j = Fe+++/(Fe+++ + Fe++), have been established through gas-slag equilibrium at 1550°C in a range of oxygen pressure of 10-I to 10-9 equilibriumatm. The value of j is increased by basic additions (BaO, CaO, MgO, MnO) and decreased by acidic oxides (SiO2 and TiO2). Oxygen pressure is shown graphically as a function of composition for slags which are analogous to those at the slag-gas interface of the open hearth furnace. THE progress which has been made in recent years in understanding the chemistry of metallurgical slags has been based largely on studies of slag-metal and slag-gas equilibria. There is a considerable body of knowledge which is applicable to reactions occurring at the slag-metal interface in open hearth steelmaking. There is little information concerning reactions of the slag with the furnace atmosphere and hence little basis for an understanding of the transfer of oxygen, sulphur, or hydrogen between gas and slag. The oxygen pressure of the open hearth atmosphere is normally of the order of 10-1 to 10-3 atm which differs by several orders of magnitude from that of about 10" atm at the slag-metal interface. The chemical properties of the slag, for example, the ratio of ferric to ferrous iron and the ability of the slag to hold sulphur in solution, are greatly affected by changes in oxygen pressure. This investigation was undertaken to enlarge our knowledge of the effect of oxygen Pressure on steel-making slags. Using air or controlled mixtures of CO a CO2 a range of oxygen Pressures from 10.' to 10.' was covered. Review of the Literature There are only a few references in the literature which pertain directly to this investigation. The most important is that of Darken and Gurry1,2 on the system iron-oxygen. This work included the determination of the phase diagram of the system and also a study of the field of homogeneous melts and their oxygen pressures. Their apparatus and procedure were very similar to that used in this study. Iron oxide was melted in a platinum crucible under an atmosphere of CO2:CO, CO2:H2, H2O, CO2, air or O2 depending upon the partial pressure of oxygen desired. After equilibrium was reached, the sample was quenched and analyzed for ferrous and ferric oxide. By appropriate calculations these authors were able to determine the oxygen and iron activities in the various slags, heats of formation of the oxides of iron, and heats of solution of iron and oxygen in the liquid slags. In a subsequent paper' the same authors made a less thorough investigation of the effects of additions of lime and manganese oxide on the composition of iron oxide melts. Only a few experiments were made and those in a narrower range of temperature and oxygen pressure. Darken' has investigated the fusion temperature of iron oxide in contact with silica under various atmospheres. He found that the temperature changes from 1120° to 1447°C as the gas composition changes from CO2/CO equal to 20.8 to pure oxygen. A comprehensive paper by White" predates the work of Darken and Gurry. The decomposition of ferric oxide into oxygen and lower oxides of iron was studied from 1000° to 1650°C and under oxygen pressures from 2 to 76 cm of mercury. The effect of

Jan 1, 1954

By AIME AIME

SCANDINAVIAN countries seem somehow to furnish an amount of talent and leadership far be- yond their population and among them Sweden is possibly at the top. The United States has many eminent citizens born in the latter, country or who are of Swedish descent and the engineers may claim their full share. In fact, the number is so large that a flourishing Swedish-American Engineering Society has been formed, including a number of A. I. M. E. members. Dr. Waldemar Lindgren is more scientist than engineer, though his work in economic geology has contributed directly to the development of many mines, and he is the valued- adviser of a number of our larger companies. Probably he, himself, values most highly the contributions he has been able to make to scientific theories of the occurrence and genesis of ore deposits. His fellow scientists have placed upon these the high mark of approval by electing him to the National Academy of Sciences, and Princeton University in 1916 recognized his position by conferring on him the degree of Doctor of Science.

Jan 1, 1931

By Klaus M. Zeitler

INTRODUCTION One cannot discuss the subject of "Raising Capital in the 1990s" without having a crystal ball and a reliable fortune teller. This discusses "Raising Capital for the 1990sW, which is what Metal1 Mining Corporation did in 1987. We raised (3166 million in an IPO (initial public offering) that was originally planned for only some (375 million. Why did we raise this money? How did we do it, and why was this IPO so successful? The answer to the first question requires a description of the promoter and principal shareholder of Metal1 Mining Corporation, Metallgesellschaft AG. This West Germany company was founded over 100 years ago in Frankfurt as a trading house for non-ferrous metals. It has developed into one of the world's leading firms in the non-ferrous metals industry. The company's worldwide activities in all areas of that business include mining, smelting and refining, the trading of ore, base and precious metals, the production of semi-fabricated and finished metal products, and the provision of engineering, construction and transportation services. Metallgesellschaft AG has also diversified into many other areas, the most significant of which are manufacturing, the production of chemicals, the development and application of technical and chemical processes, the planning and construction of industrial plants, and activities associated with finance, insurance, shipping and freight forwarding, and the provision of barter and countertrade services. The company maintains a network of more than 100 offices around the world; it employs some 25,000 people in its worldwide activities. [Selected financial data, as of September 30, 1987: (MetaUgesellschafl AG) Working Capital DM 8%.6 million CDNS 672.8 million Long Term Debt DM 568.0 million CDNS 426.2 million Sales DM 14.9 billion CDNS 11.2 billion Net Income DM 87.7 million CDN$ 65.8 million Market Capitalization at April 27, 1987: (Metallgesellschafi AG) Outstanding Shares ~,6oo,o0o DM 1,875 million CDNS 1,407 million] For the fiscal year ended September 30, 1987, Metallgesellschaft AG had, on a consolidated basis, net sales of DM13.3 billion, net income of DM100 million and total assets of about DM7.0 billion. Metallgesellschaft AG established the American Metal Company, a predecessor of AMAX Inc. one of the largest ventures undertaken by Metallgesellschaft AG then was the acquisition, through the American Metal Company, of a majority share in the Mexican Penoles mine, a large lead and silver deposit. METALLGESELLSCHAFT AG Figure 1 depicts an overview of Metallgesellschaft AG before and at the time the initial public offering of Metall Mining Corporation's shares took place. It shows that mining was far from the centre of Metallgesellschaft's activities. Therefore, it could not expect to receive an extraordinary amount of board attention. Thus, mining investments not only had to compare well with other mining opportunities, but were in fierce competition with projects from other divisions. In addition, mining was sub-divided into two separate departments -- domestic and international. These two departments had different management styles and diverging interests which resulted in a minimum co-operation between them. The domestic mining department was primarily interested in the survival of the local mines. These mines were characterized by rising operating costs and declining ore grades. It took a special commitment and continued ingenuity to develop and adjust to local conditions, and modern mining and processing technology, in order to remain competitive, or at least survive within the international mining industry. Local management

Jan 1, 1990

By Charles W. Chesterman

Perlite is a glassy volcanic rock which will, upon rapid controlled heating, expand or "pop" into a frothy material of low bulk density, valued as a lightweight aggregate. The term perlite also is applied to the expanded product. The chemical composition of perlite ranges from that of rhyolite to that of andesite; the water content ranges from 2 to 5%. Most perlite is pale gray, but some is black, brown, or even green. Inclusions in perlite are common and include phenocrysts of quartz, feldspar, biotite, and hornblende, and miscellaneous rock fragments. Occurrences of perlite are restricted to areas of Tertiary and Quaternary volcanic rocks. Perlite occurs as flows associated with thick accumulations of pyroclastic debris and other flow rocks, as dikes, sills, domes, and as selvages of intrusive bodies of volcanic rock. Individual flows of perlite range in thickness from a few feet to as much as 100 ft and commonly cover several square miles. Dikes and sills of perlite generally are small, but domes generally are substantial in size and may be as much as several miles in diameter. Most perlite deposits are large enough and topographically situated so as to lend themselves to low-cost open pit mining methods. Conventional equipment is employed in the mining of perlite. Although milling procedures may appear to be simple, care is exercised in order to produce a carefully sized product and to minimize the production of excessive quantities of fine materials, which have limited use and are considered as waste. Perlite is processed, or "popped," in one of two basic types of furnaces: horizontal rotary or vertical stationary. Both types of furnaces include product collection and dust control systems. Many commercial deposits of perlite are known to occur throughout the world, and although no exact estimate of reserves is available, there appears to be an adequate supply to meet current and future worldwide requirements. End Uses The uses of expanded perlite are many and varied and are based primarily upon its physical and chemical properties. Because of its (1) low bulk density, which generally ranges between 2 and 20 lb per cu ft; (2) low thermal conductivity "K" factor (Btu per hr per sq ft per OF per in, of thickness), which ranges between 0.267 for loosely packed perlite (bulk density of 4.48 lb per cu ft) to 1.25 for perlite gypsum plaster; (3) high resistance to fire; and (4) low sound transmission, expanded perlite is used to a great advantage as aggregate and insulating material in the construction industry. Early uses of perlite were related exclusively to the construction industry, which now consumes about 60% of the domestic production. The primary use of perlite now is as aggregate in insulation boards. Other uses of perlite in 1971 were as aggregate for plaster, horticultural aggregate, low-temperature insulation (cryogenics), and concrete. Because of its low thermal conductivity ("K" factor), high adsorption of sound, low bulk density, and fire resistance, perlite aggregate plasters hold many advantages over conventional plaster. Perlite aggregate plaster lends itself to machine applications, dries quickly, and has relatively high elasticity which reduces cracking after drying. These same features make perlite useful as aggregate in portland cement concrete and asphalt concrete for construction wherever weight reduction, insulation, and acoustics are of prime importance. Perlite-portland cement concrete offers up to 20 times more thermal insulation than conventional concrete, and because of this it finds wide application in roof decks and floor fill in multistory buildings, in

Jan 1, 1975

By J. C. Melrose, W. R. Foster, J. G. Savins, E. R. Parish

Many differences can be imagined between gas-oil flow in which the gas is supplied at the face of the core and gas-oil flow in which the flowing gas was originally dissolved in the oil. If capillary pressure characteristics and flow requirements control gas saturation distribution, the gas would be expected to be located at preferred sites within the porous medium as determined by pore sizes. On the other hand, during solution gas drive the gas first appears as bubbles through a nuclea-tion process. Nothing in self-nucleation theory specifies at which sites the first bubbles should be formed. In all probability they will be randomly distributed throughout the porous medium. Furthermore, it is not at all certain that even at low rates of production the gas will redistribute itself after nucleation to the channels normally occupied by gas in simple gas flow. Stewart, et at, have shown that at least for some limestone samples, oil recoveries could not be predicted for all rates of production using any one set of relative gas and oil permeabilities. An important factor in controlling recoveries during solution gas drive was the rate of bubble formation, higher rates giving higher recoveries. Stewart, et al, attributed the increase in recovery to a better distribution of the gas phase in heterogeneous limestone samples than is obtained by simple external gas drive. Differences in recovery from these causes were not reported for sandstone cores. In the experiments to be reported here, oil recovery, pressure and producing GOR history were measured during solution gas drive for a 5-ft sandstone core. The results were compared with predictions from the Muskat method for computing solution gas-drive behavior using external gas-drive relative permeability. The effects of changing the rate of production and oil viscosity were studied. At high laboratory rates of average pressure decline, two observations were made which would not have been predicted by Muskat's depletion theory: (1) oil recovery increased with increasing rate of production for a given viscosity oil, and (2) oil recovery increased with increasing oil viscosity for a given high rate of production. Both of these observations are explained as consequences of diffusion control of gas saturations superimposed on the normal gas-oil flow requirements, Fur- thermore, discontinuous gas phase flow appears to be significant during solution gas drive. The laboratory tests were performed at rates of average pressure decline many times greater than the maximum possible rate of average pressure decline in an actual oil field. It is, therefore, not possible to draw any direct conclusions regarding the effect of rate on recovery for the solution gas-drive mechanism under actual field conditions. However, at the lower laboratory rates, recoveries were nearly independent of rate and could be predicted by the Muskat method, using external gas-drive relative permeability data. These results suggest that at normal oilfield rates the effect of rate on recovery for the solution gas-drive mechanism is negligible. EXPERIMENTAL PROCEDURES The core material for the pressure depletion studies was Bandera sandstone from an outcrop in the Mid-Continent. This sandstone was selected because of its low permeability (about 10 md), which would permit the development of substantial pressure gradients in the corn at moderate flow rates. The core was 5-ft long and 2-in. in diameter. Its properties are listed in Table 1. Relative gas-to-oil permeability ratios were measured by an external gas-drive method2. The results are shown for a short 2-in. core and for the 5-ft core in Fig. 8. Oils used in the pressure depletion experiments were kerosene and a highly refined white oil (standard white oil No. 3) with gas-free viscosities of 1.8 and 25 cp, respectively. The gas was a naturally occurring methane from Gough field, Inglewood, Calif. The oil viscosities, gas solubilities and formation volume factors are plotted as functions of pressure at 75°F in Figs. 1 and 2. Methane viscosities and compressibilities were obtained from the literature"'. A core mounting was required which could withstand up to 2,500 psi internal pressure. This was obtained by first encasing the core completely in a plastic resin (Scotch Cast, manufactured by Minnesota Mining & Manufacturing Co.) The plastic covered core was then inserted into a steel pipe equipped with screw caps so that the plastic coating could be pressured from

By M. B. Bever, A. B. Michael

The solidification of aluminum-rich aluminum-copper alloys was investigated for different solidification rates. The measured amounts of nonequilibrium eutectic were compared with the amounts calculated on the assumption of no diffusion in the solid. The morphology of the eutectic was studied and dendritic spacings were measured. Compositions of the cored primary solid solutions were determined by quantitative autoradiography after activation of the solute copper by neutron irradiation. CONSIDERABLE progress has been made in recent years toward an understanding of the solidification of metals. This is especially true for the factors involved in nucleation, the controlled growth of metal crystals from melts, and various aspects of the freezing of ingots and castings. Many features of the solidification process, however, are not understood adequately and much further work is required. In the research reported here the solidification of a series of aluminum-rich aluminum-copper alloys was investigated. Different degrees of deviation from the idealized case of equilibrium solidification were attained by varying the rate of solidification. Thermal analysis and microscopic examination were supplemented by lineal analysis and autoradiography. The latter required the use of radioactive tracers and was adapted to the quantitative determination on a microscale of concentrations of copper dissolved in aluminum. The tracers were produced in situ by activating the copper with neutrons. These techniques permitted a correlated interpretation of the temperature-time history, the amounts of nonequilibrium eutectic and the general morphology of the alloys, and yielded quantitative data on microsegregation. Nonequilibrium Solidification In the general case of the solidification of a solid solution in accordance with the phase diagram, the composition of the coexisting liquid and solid must change continuously. This change requires diffusion, which at best remains incomplete in the solid during solidification. The resulting inhomogeneity of the solid solution crystals is well-known as coring, dendritic segregation, or microsegregation. The generally accepted analysis of coring assumes that, 1—no diffusion occurs in the solid, 2—diffusion is complete in the liquid, and 3—the composition of the solid formed on cooling through any infinitesimal temperature interval is given by the solidus of the phase diagram. On this basis, In this equation m designates mass, x designates the concentration of solute and the subscripts L and S refer to the liquid and solid phases, respectively; the subscript o indicates the initial state, in which the liquid is identical with the entire system. Eq. 1 or its equivalent has been derived repeatedly'-7 and an analogous equation, known as Rayleigh's equation, has been used for distillation. The assumptions on which Eq. 1 is based do not include an infinitely fast cooling rate as sometimes stated. In fact, Olsen and Hultgren %ave shown by experiment that very high solidification rates suppress coring, presumably by preventing diffusion in the liquid and by the effect undercooling has on the composition of the nucleus. Coring thus occurs at rates of cooling which are too fast for a close approach to equilibrium in the solid and too slow to suppress diffusion in the liquid and to cause marked undercooling. If the liquidus and solidus approximate straight lines, Eq. 1 simplifies to The fraction of liquid present at any temperature during nonequilibrium solidification can be calculated from Eqs. 1 or 2. By the lever relation it is

Jan 1, 1955

By A. S. Odeh

This paper analyzes the effect of limited entry to flow at the wellbore on the steady-state productivity of a well. Wells that have been opened to flow along a fraction of their productive interval are termed wells with limited entry. Previous work treated the cases of a partially penetrating well, a well producing from the central portion of the productive interval and a well in which several intervals equally spaced were open to flow. In this paper the open interval can be located anywhere within the productive interval. Thus, in a sense, it generalizes previous work. The finite cosine transform was used to arrive at a solution for steady-state flow of a slightly compressible fluid. The solution was programmed for a CDC 1604 computer. Numerical vaIues for rd = 660 ft, r, = 1/4 ft, and range of sand thickness of 20 to 200 ft are presented in graphical form. The effect of rd and r, values on the result is shown in a table. The correct calculation of skin and damage ratio in the presence of limited entry to flow is explained and illustrated by examples. Moreover, the paper shows how to calculate the net decrease in productivity due to the combined effect of limited entry and perforations. INTRODUCTION In some wells only a fraction of the productive interval is open to flow. Location of this fraction is usually dictated by formation characteristics and reservoir behavior. For instance, if a gas cap exists, the open interval is located away from the gas-oil contact to prevent any possible gas coning. Wells that intentionally have been opened to flow along a fraction of their productive formation are tened wells with limited entry. Obviously, unintentional completions of this type also exist. Limited entry to flow decreases well productivity. Magnitude of the loss depends on the fraction of the formation open to flow, on the thickness of the sand, on the location of the open interval and on the ratio of rd /r, where r , is well radius and rd is the drainage radius of the well. The use of pressure buildup data on producing wells to calculate the condition of the formation around the wellbore is an accepted practice. van Everdingenl and Hurst2 introduced the concept of she skin factor s considered to be due to a thin layer of different permeability immediately around the wellbore. These authors dealt with the case of a well of complete radial geometry, i.e., a well with open-hole completion that completely penetrates the formation. The presence of a low-permeability skin results in a loss of productivity, as does limited entry. Therefore, if pressure buildup data obtained on a well with limited entry are used to establish the presence or absence of skin (i.e., formation damage), and a correction is not made for this loss of productivity, the calculations would result in an erroneous skin value. They might indicate the presence of formation damage when in reality there is none, or they might indicate a value larger than the true value. This could lead to an incorrect basis for planning remedial measures. Muskat3 studied the problem of partially penetrating wells for the case of incompressible flow. He presented equations and figures which allow estimation of loss in productivity. Brons and Marting,4 using equations based on Nisle's work,5 studied the loss of productivity for three cases. The first was for a partially penetrating well; the second was for a well producing from only the central portion of a productive interval; and the third was for a well in which several intervals equally spaced were open to flow. Their work was for steady-state depletion-type reservoirs wherein the well radius of drainage is established and the fluid is considered to be slightly compressible. Considered in this paper is the problem of wells with limited entry in which the open intervals are located anywhere within the productive sand. The finite cosine transform is used to arrive at a

Jan 1, 1969

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965

By Willard P. Ward

HAVING been engaged during the past year in the manufacture of ferro-manganese in a blast furnace, I have imagined that some further information on this subject might be of interest to that large number of members of the Institute who are engaged in the iron and steel industries. The great question of the economical production of good steel, ingot metal, or homogeneous iron (we scarcely know now what to call it) from good materials, and at reasonable prices, has, thanks to the intelligence and energy of a few American engineers, been successfully solved in this country. Nearly all first-class railroads, and many that would riot rank so high, have adopted the Bessemer rail. Martin boiler-plates are rapidly gaining ground, in competition with

Jan 1, 1877