Search Documents

By H. K. van Poollen, H. C. Bixel

A treatment is given of the transient pressure behavior of a well located at the center of a circular region surrounded by a radial discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility and porosity are uniform but may be different from those on the other side of the discontinuity. The results are obtained by solving a pair of finite difference equations. The numerical solution to these equations is obtained using a digital computer. The results are compared with previously published, approximated analytical solutions to the same problem. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables studied include dimensionless time from '0.001 to 100 and storage capacity ratio from 0.001 to 1,000. The well behaves as if it were in an infinite reservoir for dimensionless times less than 0.25. Reservoir properties near the well can be estimated in the usual manner. An overlay technique is used to match an experimental curve with one of the theoretical curves. It is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time tD at which a match occurs into the equation a = (0.000264 tk1/tD , µ1 cI)I/2 where kI/ I µI cI is the diffusivity near the well, and may be estimated from data taken at early time. Several buildup curves are computed. These curves show that for early shut-in times, correct values for transmissibility are obtained from conventional analysis. However, erroneous values of static reservoir Pressure are obtained unless data at large shut-in times are taken. INTRODUCTION A mathematical treatment of the transient pressure response of a well located at the center of a region bounded by a circular discontinuity is given. Within a region (Fig. 20) the properties of both the rock and the fluid are considered to be constant on either side of the discontinuity. While these properties are considered constant, they may be different on opposite sides of the discontinuity. A discontinuity of this type could be a fluid-fluid contact or a sudden change in rock characteristics such as thickness, porosity or permeability. Analytical solutions to this problem are available. 1-3 However, they are so involved that they are of little practical use. An approximate solutionl is available but the range of times over which it is valid has not been specified. A numerical solution to a pair of finite difference equations is used to obtain the solution given in this paper. PREVIOUS WORK One of the first solutions to the problem was published by William Hurst.1 Hurst considered unsteady-state flow of fluids through two sands in series with different mobilities in each sand. He used Laplace transforms to obtain a solution for a single well located at the center of the circle enclosing the first of the two sands. In this case, the solution for the pressure change in Region I (Fig. 20) is2

By B. Fazan, O. D. Sherby, J. E. Dorn

McLean's technique was employed to determine the effect of temperature on the contribution of grain boundary shearing to the total creep strain in pure aluminum over the range of 610° to 747°K. The contribution of grain boundary shearing at the same stress was found to depend upon a temperature-compensated time, where the activation energy AH was practically identical with that for total high temperature creep. SEVERAL outstanding investigations by McLeanl-' have demonstrated that the total creep strain in polycrystalline aluminum at 473°K arises from microscopically detectable slip, subgrain tilting, and grain boundary shearing. Whereas microscopically detectable slip arises from dislocations that move out of the grains, subgrain tilting is due to entrapment of dislocations of like sign in subgrain bound-arles. Consequently, creep in polycrystalline aggregates appears to be the resultant of two mechanisms, namely, migration of dislocations and grain boundary shearing. This suggests that an appropriate law for creep should contain two additive terms ?1 = ?d + ?yb where the total creep strain, ?1, depends on the sums of the creep strains arising from motion of dislocations, ?d, and from grain boundary shearing, ?yb. But extensive investigations5 over wide ranges of alloys, grain sizes, temperatures, and stresses have shown that the total creep strain is quite accurately dependent on the single term functional relationship ?1 = f (?), s = constant where s is the stress (constant),* ? = te-?H/RT, t is the time under stress, AH is the activation energy, R is gas constant, and T is absolute temperature. Since Eq. 2 was found to be valid over those ranges where appreciable grain boundary shearing is observed, it appears probable that the activation energy for grain boundary shearing might be identical with the activation energy for migration of dislocations. Thus, under a given stress, it could be thought that where fd and fgb represent the appropriate functions for each mechanism of creep. The primary objective of this investigation was to obtain a direct check on the accuracy of this hypothesis. Experimental Procedure and Results Rolled aluminum sheet (99.987 pct Al), 0.100 in. thick, was used in this investigation. Creep specimens having a 0.25 in. wide, 3 in. long gage section were so machined that their axes were in the rolling direction. All specimens were annealed for 9 hr at 894°K before testing to produce a mean grain diameter of about 0.1 in. One face of each specimen was polished electrolytically in 10 pct HBF4. In order to permit accurate measurements of grain boundary shearing, the polished surface was lightly scribed with a ruling machine accurate to ±0.0001 in. to give a uniform grid of lines which were 0.01 in. apart. Although it was thought that surface working might modify the creep behavior in the vicinity of the scribed grid lines, this technique nonetheless was employed because such local differences in creep properties should not modify seriously the fractions of the total creep strain due to grain boundary shearing or to migration of dislocations. All creep tests were conducted under constant load with an initial stress of 250 psi. The specimen tem-

Jan 1, 1955

By Ottar Dragge, C. Danielsson, Bo Kalling

THE desulphurizing of pig iron has been accomplished with a number of different additions. The oldest and still most commonly used agent is soda, the extensive use of which commenced about 1925, when it was used principally for cupola furnace iron. More recent experience' seems to show that better results can be obtained with sodium hydroxide. The well-known desulphurizing properties of lime have also been exploited in different technical processes. Another material with even more powerful effect is calcium carbide.' The desulphurizing ability of manganese, when added to the ladle in sufficient quantity, should also be mentioned in this connection. During recent years increasing attention has been paid to the desulphurizing properties of metallic magnesium." An addition of a suitable alloy of magnesium is now in use purely for the purpose of sulphur elimination. Of the desulphurizing agents mentioned, lime is by far the cheapest, provided that the reaction can be brought about rapidly and completely. Therefore, a method that makes full use of the desulphurizing ability of lime may be able to compete with other processes. A method developed at the Dom-narfvet Iron and Steel Works (Sweden) will be described, which enables pig iron to be rapidly desulphurized to very low sulphur contents by using a burnt lime powder. as the desulphurizing agent. Lime in Older Processes In cases where lime has been used for the desul-phurization of pig iron, it has generally not been used alone, but mixed with other substances such as fluorspar, to obtain the formation of a molten slag during the process. This method has been tried by Tigerschiold,' who treated the iron with a lime-fluorspar mixture, the stirring of the iron being brought about inductively with low frequency alternating current. Very good results were obtained. A process of this type has also been suggested by R. P. Heuer, U. S. A. The principles of this method, which has been tested in Great Britain by Newell. Lanener. and Parsons." re that a mixture of lime and fluoispar is added to the hot metal in the ladle, while a powerful stream of nitrogen gas is blown into the bath to produce the required intermixing. The results of the tests were unsatisfactory, however. A similar process has been developed at The Steel Co. of Canada, according to a statement by H. M. Griffith.' Here the tests were carried out in a carbon-lined ladle provided with carbon tuyeres in the side wall for blowing nitrogen into the bath. The addition consisted of about 20 lb of a mixture of burnt lime and fluorspar per ton of pig iron. Good results appear to have been achieved. The sulphur content of the pig iron is stated to have been reduced from 0.025 to 0.050 pct down to 0.006 pct. Various methods of desulphurizing pig iron have been tried using lime powder without fluxing material for fusing. Eichholz and Behrendt7 have experimented with blowing a powdered limeicoke mixture with air into the ladle. Their results were, however, not conclusive and the experiments do not appear to have been continued. Similar experiments have been carried out at Domnarfvet, using nitrogen instead of air in order to avoid oxidation. But these attempts were not particularly successful. It appears to be difficult to achieve the required agitation by this means. The strong cooling effect of the gas on the iron is also a serious drawback. A method in many respects similar to that tried at Domnarfvet was tried by Eulenberg and Krus at the end of the 1930's. Here again desulphurization was carried out with lime alone, brought into contact with the molten iron in a rotary furnace. The temperature was kept at the required level, 1400" to 1500°C, by the introduction of a pulverized coal burner in one end of the furnace. The speed of rotating was not given. A paper by Bading and Krus states that, in one of the first experiments, the sulphur content in 56 tons of pig iron was brought down from 0.186 to 0.035 pct in 117 min, but that a considerable shortening of the time would be possible. According to later reports by Eichholz and Behrendt,' it should be possible by this process to achieve a desulphurization speed of 0.35 pct S per hr for a consumption of 6 to 10 pct limestone and 2 to 3 pct coke, as fuel exclusively. The final sulphur content is, however, not stated. Domnarfvet Method After a number of different procedures had been investigated, the tests at Domnarfvet were directed to desulphurization with lime in a rotary furnace. Before going into the practical details of the method, the theoretical aspects will be discussed briefly. If the pig iron does not contain alloying elements other than carbon, the reaction can be expressed most simply by the usual equation: FeS + CaO + C = Fe + CaS + CO [I] 4H,. ~ 34,000 cal That this reaction can be carried through to a very complete desulphurization of pig iron has been shown by OelsenD in a discussion in connection with the Eulenberg and Krus' method. He mentions two laboratory tests, in one of which the sulphur content in the pig iron at 1400°C was reduced from 0.540 to 0.006 pct after treating with 3.35 pct lime. The pig iron had a low manganese content, but other analysis is th. given. Mention also should be made of the recently published investigations by Fischer and Cohnen'" dealing with the influence of the carbon content of the iron on desulphurization with lime, although in this case fluorspar was added also. The tests show that efficient desulphurization is possible with lime in the steel bath, provided that the carbon content is sufficiently high. The temperature employed in these tests was considerably higher (1620") than that normal for treatment of pig iron. The author concludes that the product S% X C% - 0.011 at the temperature in question.

Jan 1, 1952

By M. T. Hepworth, A. K. Stewart

Iron containing 0.1 pct A1 and -0.9 pct P by weight was internally oxidized in the temperature range 900° to 1300° C, where the bcc structure is stabilized by phosphorous. By measuring the depth of penetration of oxygen with time in an internally oxidized zone for an imposed surface oxygen potential, oxygen permeability was determined. The dgfusion coefficient of oxygen in iron was then calculated using known solubility data, yielding the expression: where Do is the diffusion coefficient of oxygen in bcc iron in sq cm per sec and T is temperature in OK. RECENTLY Hepworth, Smith, and Turkdoganl measured the diffusivity of oxygen in bcc iron and reported the temperature dependence of diffusivity from data determined in the a, and 6 temperature ranges. Subsequently Swisher and Turkdogan' have measured the diffusivity of oxygen in fcc iron. Internal oxidation techniques were employed by these investigators and in this current study. The analysis of this technique is developed by wagner3 (presented in English by Hauffe4 and Rapp 5). In this present study bcc iron stabilized by phosphorous was used to determine oxygen diffusivity in the temperature range 900° to 1300°C. Meijerin 6 has studied oxygen permeability in this temperature range using bcc iron stabilized with 5 pct Sn. Other inves- tigators who have studied oxygen permeability in bcc iron at other temperatures are Schenck et al., 7 Bohen-kamp and Engell, 8 and Bradford. EXPERIMENTAL Electrolytic iron of 99.99 pct purity was alloyed to contain 0.897 pct P and 0.093 pct Al. The maximum weight percent phosphorous required to stabilize bcc iron between 910" and 1392°C is 0.51 pct as determined by Haughton,10 0.42 pct by Roquet and jegaden," and 0.58 pct by vogel,12 with the latter value preferred by Hansen.13 Microprobe analysis indicated that there was no segregation of the phosphorous either before or after permeability studies; therefore, the quantity of phosphorous added was assumed to be sufficient to stabilize the bcc structure. Furthermore, the permeability results of studies on this alloy agreed substantially with interpolated values from previous data on bcc iron.' An ingot of the Fe-P-A1 alloy was hot-rolled to a l-in.-thick slab. Specimens were machined to dimensions: 13/8 by $ by 1/4 in. The experimental apparatus and procedure used have been described before.' A constant oxygen potential was established by passing argon and hydrogen through a column of oxalic acid dihydrate, which has a water vapor pressure which is well-known as a function of temperature. Slab specimens were exposed to a gas mixture sufficiently lean in oxygen to prevent the formation of a surface oxide for predetermined temperature for selected times. The specimens were then quenched, sectioned, and examined metallo-graphically. All quenched specimens were iron-plated to provide protection from the outside sample edge during polishing. Fig. 1 shows a typical microstruc-ture for a specimen oxidized at 953°C for 48.00 hr at a water vapor-to-hydrogen pressure ratio of 0.20. DISCUSSION AND RESULTS The following equation was derived by Hepworth et al.' from Wagner's kinetic expressions for internal oxidation:

Jan 1, 1969

By Alexander R. Troiano, Taylor Lyman

Studies of the transformation of aus-tenite at constant subcritical temperatures have been numerous since the work of Davenport and Rain.' Considerable information has been obtained on low-alloy steels and on high-carbon alloys containing undissolved carbide or graphite at the austenitizing temperature. Little is known of the isothermal transformation of aus-tenite containing in solution large amounts of both carbon and a single alloying element. In this investigation four steels containing one per cent carbon and with chromium in the range 3 to 9 per cent have been examined with the view to establishing the fundamental character of the isothermal reactions when all carbon and chromium are initially in solution in austenite. Experimental Procedure Alloys The chemical compositions of the steels investigated are given in Table I. The 4 per cent Cr alloy is a commercial steel. The other steels were made by the Carpenter Steel Co. as 50-lb., induction-furnace heats and rolled to 5/8 -in. round bars. Bars were softened at 650' to 700°C. before the specimens were cut. Most of the lines on the transformation diagrams presented here have been placed on the basis of the microscopic examinatioll of partially reacted specimens, Thees specimens were approximately 1/2 by 1/4 by 1/8 in. ill size, specimens of the 9 per cent cr steel were held 10 to 12 hr, at 1200°to 1225°C. before quenching to the various subcritical temperatures. The other steels were held for 2 to 2 1/2 hr. at 12ooOC. before quenching. These treatments, carried out in an atmosphere of purified nitrogen, produced an austenite grain size larger than A.S.T.M. So. I, some grains being 1 to 2 mm. in diameter. There were a few undissolved carbide particles in some specimens of the 9 per cent Cr steel. It is believed, however, that any errors in the results due to incomplete solution of carbon and chromium in austenite are negligible; that is, austenite compositions may be considered as being those listed ill Table I. X-ray Methods Constituents were identified and mar-tensite axial ratios determined from Debye

Jan 1, 1945

By M. H. Loveman

THE orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6', longitude E 97°20', about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Symes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 annually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 12, 1916

By Milo W. Krejci

The plant and quarries of the Inland Portland Cement Co. are located at Metaline Palls, Wash., about 128 miles north of Spokane, on the Pend Oreille river, and within 10 miles of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in the construction of the power plant, the works were not put into operation until August, 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. 1 is a view and Fig. 2 is a plan of the works. Water Power Development.—The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and' 0.5 mile wide, situated in the Kaniksu Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 ft., and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by 8 ft. in cross-section, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond was used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural course of Sullivan creek to the Pend Oreille river. The water is taken from this intermediage storage by means of a 6 by 8 ft. wooden flume approximately 13,000 ft. long. This flume is built up on the side hill, piling being driven most of the way on

Jan 1, 1914

HE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe2O3), and phosphorus oxide (P2O5) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1951

By W. F. Flanagan, D. H. Polonis, S. D. Dahlgren

Rotation diffraction patterns of Cu-4.84 wt pct Si polymystalline samples were taken during the course of isothel-ma1 affing of the suPersaturated a phase, a diffraction spots were obserzled to streak during the initial stages of aging, and this streaking was similar to the streaking of a spots observed earlier by Barvett with deformed super saturated samples of the same composition. Although it was suggested that stacking faults were the sole cause of styeaking in the deformed samples, the present study has shown that plates with one small crystallite dimension can also contribute to the streaking when there is lattice coherency across close-packed planes. THE decomposition of the supersaturated a phase in Cu-Si alloys has been reported to occur by means of both thermal and stress activation.1-4 According to the Cu-Si phase diagram,3 Fig. 1, the supersaturated a phase (fcc) is expected to transform during aging by the precipitation of the y phase. The results of earlier studies2,4 have indicated that metastable k phase (hcp with nearly ideal close packing) forms initially at temperatures below the eutectoid temperature, after which the k transforms to the a and y phases. Hof-mann et al.4 have proposed a metastable version of the phase diagram, showing the approximate boundaries for k formation below the eutectoid temperature. In view of the close-packed nature of both the a and k phases, it is essential to consider the role assumed by stacking faults in the transformation. Streaking effects have been reported by Barrett 1 in the rotating crystal X-ray patterns of strained Cu-Si alloys and were attributed to stacking faults rather than particle size effects. This deduction was based on the observation that streaks in the diffraction patterns did not occur tangent to the 220fee Debye ring. It is known that the atom movements involved in faulting leave some X-ray reflections unaffected while others are broadened,' and, in particular, it has been shown that faulting will not cause streaking of 220fee reflections tangent to the 220fee Debye ring as would be expected if all the reflections were broadened.' The formation

Jan 1, 1967

By E. B. Olds, B. P. Burt

The mines of the Consolidated Gopper-mines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 11/2 miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1949

By Frank Schrader

INTRODUCTION THE present sketch is submitted by request in the hope that it may serve as a basis for geologic discussion of the mining camps in Mohave County, which is experiencing a marked revival of activities. The region, commonly known as the Mohave district and Kingman district, lies in western Arizona in the southern part of Mohave County, bordering California and Nevada on the west (Fig. 1). Kingman, the principal-town; is situated near the center of the area. on. the Atchison, Topeka & Sante Fe Transcontinental Railway. This region is composed of naked desert ranges of mountains and broad detritus-filled valleys, the southern extension of the characteristic topography of the Great Basin. In altitude it varies from 500 ft. in the southwest to 8,300 ft. on Hualpai Peak southeast of Kingman. The mountains trend north-northwest. They rise about 3,000 ft. above the valleys, are generally rugged and were formed mainly by erosion. They are composed in the main of a, complex of pre-Cambrian granitoid rocks which underlies the area as a whole. Like the valleys, they average about 10 miles in width. Beginning on the east, they are the Grand Wash Cliffs, the Cerbat Range, the Black Mountains or River Range, and the Eldorado Range. The upper or dominantly cliff half of the Grand Wash Cliffs, marking the edge of the Colorado Plateau, is composed of nearly horizontal sedimentary Paleozoic strata of the Grand Canyon section, and the lower half of the underlying pre-Cambrian complex. The Cerbat Mountains situated in the central part of the area, and the Black Mountains situated between Detrital-Sacramento Valley on the east and Mohave Valley, the great trough of the Colorado River, on the west, are locally flanked or overlain by Tertiary volcanics (Fig. 2). The latter consist of five groups of mountains of which the most important is the Black Mesa group on the south. The Eldorado Range, rising from the great trough of the Colorado on the west and containing Searchlight, Eldorado Canyon, and other camps, is topographically and geologically similar to the Black Mountains.

Jan 10, 1916

By R. F. Mehl, M. Gensamer

Although a large number of X-ray photograms of cold-rolled steel have been published, two circumstances have led to the experimental work reported in this paper. The first is that no complete study, making use of the pole-figure method of Weverl, has been made of cold-rolled low-carbon steel. Wever has published pole figures of mild steel subjected to plane parallel deformation1, 2 and undoubtedly he has applied the method to cold-rolled mild steel, but the authors have not found these data published. Kurdjumow and Sachs3 have applied the method to the study of rolling and recrystallization textures in electrolytic iron; their results will be referred to later. The reason for this dearth of papers using the pole-figure method is obvious; a greater number of photograms and more analytical work (although this work is quite simple and straightforward) are required to construct a pole figure than most investigators have felt worth while, despite the fact that no other method of which the authors are aware will satisfactorily depict the orientations of the crystallites in a polycrystalline aggregate. The second circumstance that led to the work reported in this paper was the appearance of a paper by Wayne A. Sisson4 on the same subject. In his valuable study of the factors influencing the development of preferred orientations in cold-rolled mild steel, Sisson made one observation that required confirmation; that is, that at some stage of the rolling process the type of preferred orientation changed from the type that gives a photogram characterized as a "six-point" X-ray pattern to that known as a "four-point" pattern. A similar observation had been made by Tam-mann and Heinzel5, who studied the orientations developed in the rolling of steel by the specular reflection of light from the etched surface of rolled samples. These workers also found that the type of preferred orientation changed during the rolling process. The authors had some difficulty in seeing how this behavior could be consistent with modern views on the genesis of preferred orientations, particularly with those of Wever2

Jan 1, 1936

By R. F. Mehl, M. Gensamer

Although a large number of X-ray photograms of cold-rolled steel have been published, two circumstances have led to the experimental work reported in this paper. The first is that no complete study, making use of the pole-figure method of Weverl, has been made of cold-rolled low-carbon steel. Wever has published pole figures of mild steel subjected to plane parallel deformation1, 2 and undoubtedly he has applied the method to cold-rolled mild steel, but the authors have not found these data published. Kurdjumow and Sachs3 have applied the method to the study of rolling and recrystallization textures in electrolytic iron; their results will be referred to later. The reason for this dearth of papers using the pole-figure method is obvious; a greater number of photograms and more analytical work (although this work is quite simple and straightforward) are required to construct a pole figure than most investigators have felt worth while, despite the fact that no other method of which the authors are aware will satisfactorily depict the orientations of the crystallites in a polycrystalline aggregate. The second circumstance that led to the work reported in this paper was the appearance of a paper by Wayne A. Sisson4 on the same subject. In his valuable study of the factors influencing the development of preferred orientations in cold-rolled mild steel, Sisson made one observation that required confirmation; that is, that at some stage of the rolling process the type of preferred orientation changed from the type that gives a photogram characterized as a "six-point" X-ray pattern to that known as a "four-point" pattern. A similar observation had been made by Tam-mann and Heinzel5, who studied the orientations developed in the rolling of steel by the specular reflection of light from the etched surface of rolled samples. These workers also found that the type of preferred orientation changed during the rolling process. The authors had some difficulty in seeing how this behavior could be consistent with modern views on the genesis of preferred orientations, particularly with those of Wever2

Jan 1, 1936

By F. J. Lecznar

An investigation of the problem of separating two minerals by a moving inclined plane has revealed that only minerals with considerable difference in sliding friction coefficients separate readily; that it is possible to separate two minerals when only one of them has a rolling friction coefficient; that difference in geometrical shape of the minerals is important to separation which improves as grain size increases; and that the thickness of the stream falling on the belt influences the grade of separation - the thinner the stream, the smaller the interference between the grains of the minerals to be separated and the higher the degree of separation. The problem of separating two minerals with different friction coefficients and shapes by a moving inclined plane has been investigated. Friction separators can be used to separate two materials that differ in shape and in friction coefficient. 1,3 Gladkov has presented some theoretical aspects of using a moving plane to clean corn and podded seeds; this method, however, did not result in practical application. When considering the separation of minerals, only those with considerable difference in sliding friction coefficients can be taken into account. Furthermore, it is possible to separate two minerals when only one of them has a rolling friction coefficient. The difference in geometrical shape of two minerals is also important to separation. It has been found that the separation of two minerals improves as the grain size increases. For example, coal and slate over 2 in. in grain size separate much better than materials of smaller grain size. As Table I indicates, the slate grains smaller than 25 mm gradually lose their flat shape with decreases in size and are more rounded than larger grains, which are almost flat. The smallest grains of slate in first and second fractions slide down the belt since their friction coefficients decrease and approach the value of the rolling coefficient. The percentage of separation of the first fraction is, therefore, low. Thickness of the coal stream falling on the belt also influences the grade of separation; the thinner the stream, the smaller the interference between the grains of the two minerals to be separated and the higher the degree of separation.

Jan 1, 1963

By M. Gensamer

ONLY recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Goss1 stated that hot-rolled mild steel exhibits a texture different from that charac-teristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar, 4 in. thick was hot-rolled at two temperatures, 780° and 910° C. (1436° and 1669° F.). (These temperatures refer to the tempera-ture of the furnace in which the steel was heated.) After each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7° with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Me target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780° C.), and that of the two

Jan 1, 1936

By M. Takeda, H. Majima

Pyrite has been subjected to xanthate adsorption experiments in order to determine the nature of adsorption. The identification of adsorbed species by means of IR spectroscopy, as well as UV, shows that the dixanthogen adsorption is undoubtedly predominant on pyrite surface. The rest potential measured in a xanthate solution coincides with the redox potential of the xanthate-dixanthogen couple. Considering all the factors together, the adsorption mechanism of dixanthogen on pyrite has been proposed as This mechanism is consistent with the "passive" character of pyrite. From the measurement of the redox potential of the xanthate-dixanthogen couple in the homologous series, a rule similar to that for surface tensions proposed by Traube is also applicable. The polarization experiments were conducted on pyrite in a solution containing xanthate. In the anodic polarization, xanthate is observed to oxidize to dix- anthogen, which depresses oxygen evolution on py rite at higher potential levels. In spite of the importance of the presence of pyrite in the flotation of sulfide minerals, not many studies have been made on the xanthate-pyrite system in the absence of an activator or a depressant. In an early study by Gaudin and Wilkinson,' it was pointed out that no ferric xanthate was formed on a pyrite surface, while in another study Gaudin and his collaborators2 proved the formation of a very small amount of ferric xanthate. Afterwards, Gaudin et al.3 studied the pyrite-xanthate system with a radiometric technique and found indications of the presence of adsorbed dixanthogen on pyrite surfaces. Mamiya4 studied the flotation behavior of the pyrite-xanthate system and also suggested the possibility of dixanthogen. Recently, Fuerstenau and his coworkers at The Colorado School of Mines5 studied the role of dixanthogen in the xanthate flotation of pyrite and discussed the problem in terms of such properties as oxidation potential, zeta potential, flotation recovery, pH of solution, etc. However, the mechanism of dixanthogen adsorption at the pyrite-water interface is not yet understood. This paper is concerned with an electrochemical in-vestigation through which the mechanism of dixanthogen adsorption on pyrite is interpreted. EXPERIMENTAL MATERIALS AND TECHNIQUES Pure potassium xanthates were synthesized by an

Jan 1, 1969

By E. B. Olds, Burt. B. P.

THE mines of the Consolidated Coppermines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. [ ] The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 1 ½ miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1946

By Frederic H. Lahee

After abandoning two dry holes, on the Mrs. Daisy Bradford land, C. M. Joiner finally completed his No. 3 on Sept. 8, 1930, at a total depth of 3592 ft. This well is 735 miles somewhat north of west of the town of Henderson, in Rusk County. Between Oct. 2 and Oct. 6, this well made numerous heads which indicated that it would produce about 300 bbl. daily. By Nov. 27, two dry holes,' completed near the Joiner well, taken in conjunction with the small production from this well, served to dampen any enthusiasm among those who hoped for a major pool; but by December 18 three other producers had been completed. On Dec. 28, 1930, E. W. Bateman's Lois Della Crim No. 1 drilled itself in with an estimated daily yield of between 10,000 and 15,000 bbl. from a depth of 3650 ft. This well, 10 miles north of the Joiner well, also in Rusk County, initiated the leasing campaign that led to the later orgy of drilling. On Jan. 25, 1931, Moncrief, Farrell and others completed their J. K. Lathrop 1 as another big producer, 7 miles east of Gladewater in Gregg County and 14 miles N. 20" E. from the Bateman Crim well. The Lathrop well, 3574 ft. deep, flowed 320 bbl. in 1 hr. through a ½in. choke. The first well completed in Smith County was Cook No. 1, drilled by Guy Lewis et al. in the James Jordan Survey, 4.7 miles west of the Joiner discovery well. On Mar. 30, 1931, it flowed 137 bbl. in 33 min, through a ¾-in. choke. The top of the pay sand was found at 3672 ft. Finally, in Upshur County, on May 5, the Mudge Oil Co. et al. completed the Richardson No. 1, which flowed 274 bbl. through a 4 2/64-in. choke in 2 hr. This well is 4 miles northwest of the Lathrop producer. Development It is unnecessary to give a lengthy description of the rapid development of the area discovered in these five far-separated wells, or to discuss the speculations offered as to whether there were several pools or only one.

Jan 1, 1932

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal etfect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24s-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to inter-crystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot he accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. Review of Previous Work In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknalll demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K • io"^ (i) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-~/m (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver.rich copper alloyZ and of duralumin.3

Jan 1, 1946

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal etfect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24s-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to inter-crystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot he accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. Review of Previous Work In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknalll demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K • io"^ (i) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-~/m (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver.rich copper alloyZ and of duralumin.3

Jan 1, 1946