Search Documents

By C. D. Stahl, R. Sandrea

This investigation was made to evaluate the comparative effects of the viscosity and the phase behavior of the buffer fluid in the composite solvent displacement of Bradford crude from waterflooded sandstone cores. Buffer slugs of propane, naphtha and other refined hydrocarbons exbihiting increasingly favorable viscosity ratios and decreasing solubility relationships, respectively, with Bradford crude, were used in long Berea sandstone cores. The secondary slug was isopropyl alcohol. The results indicate that higher oil recoveries are obtained for increasingly favorable phase relationships even when these are accompanied by unfavorable viscosity ratios within the range studied. Moreover, when propane is used as a buffer slug with an adverse viscosity ratio of 36, it gives higher oil recoveries than at a similar size slug of an any1 alcohol having a viscosity ratio of 1.09. The investigation was extended to the study of the effect of flooding rate on oil recovery. Residual Bradford crude was displaced from a 6-ft Berea sandstone core at rates varying from 0.3 to 30 ft/ day. The results show that as flooding rates were increased above or decreased below a minimum range of 1 to 2 ft /day, displacement efficiency increased considerably. INTRODUCTION In recent years, the alcohol slug process as a means of tertiary recovery has been the subject of many investigations. Gatlin and Slobod showed the advantages of the combination solvent slugs over the previous single-slug process.1 The combination slugs require less total slug material to obtain similar oil recoveries. The basic combination process involves injecting a primary or buffer solvent which is preferentially oleophilic, followed in turn by a water-driven slug of isopropyl alcohol. This procedure ensures that the buffer slug, which is miscible only with the reservoir oil, displaces and replaces the oil and is in turn displaced, together with the water, by the isopropyl alcohol slug miscible with both fluids. Likewise, for those reservoir oils that show some degree of phase incompatibility with isopropyl alcohol, as does Bradford crude, a proper buffer solvent can artificially make the alcohol process technically feasible. From an economic standpoint, propane or LPG would be the most appropriate primary solvent to be used in the field; however, Taber, et a12 have indicated that the alcohol process becomes highly inefficient in the displacement of light hydrocarbons because of the entrapment of these hydrocarbons during the stabilized bank formation. Moreover, since materials such as propane have such low viscosities, adverse viscosity ratios with most reservoir oils would be penerated, thereby possibly further reducing the efficiency of the buffer solvent. This paper presents the results of an experimental study of the comparative effects of viscosity ratio and phase relationships on the displacement efficiency of Bradford crude by means of dual solvents. The work was extended to include the effect of flooding rate on oil recovery. Rates within the range of field and laboratory values were used. EXPERIMENTAL PROCEDURE APPARATUS The porous media used in this study consisted of two 10-ft and one 6-ft Berea sandstone cores, 3-in. in diameter. These were cast in galvanized steel pipe of 31/2-in. ID and the annulus was filled with Armstrong cement. The 10-ft cores were assembled by connecting two 5-ft units, which were joined together by 8-in. steel flanges fitted to the pipe. Intimate contact between the two sections was obtained by inserting a thin disk of the same sandstone between the core faces. The outlet and inlet ends of the cores were covered with threaded pipe caps. The injected fluid was gravity fed to two variable-rate positive-displacement pumps. The fluids were filtered before entering the core and the effluent was collected in an automatic fraction collector and

Jan 1, 1966

By F. W. Jessen, N. Lamont

The effect of an existing fracture or joint plane, which may exist in a rock, on the extension of a hydraulically induced fracture through the rock has been investigated in the laboratory. By use of a series of models made from various outcrop rocks, the width and orientation of existing fractures do not alter the extension or direction of the hydraulic fracture. The results, which conform quite well with the Grifith theory of failure, are illustrated by a series of photographs of the various models. INTRODUCTION The process of hydraulic fracturing has been widely used in the oil industry since its introduction in 1948 and has made possible the production of many reservoirs which would have been uneconomical prior to this process. Numerous studies of the mechanics of the process2-h nd of the effects of oriented fractures on recovery'.' have appeared in the literature. The increased recoveries led to attempts to predict the orientation of hydraulic fractures at the wellbore and to the development of methods to control this orientation. Field tests have been devised"." which indicate the validity of theoretical predictions of fracture orientation at the borehole. The direction of extension of hydraulic fractures from the borehole has not received much attention since most studies have predicted, at least implicitly, that a fracture will continue in the same plane unless a change of state of stress in the rock occurs. Since such predictions are based on the assumption of rock homogeneity, the effects of rock heterogeneities are left unknown. Most sedimentary rocks are composed of layers which reflect the changing depositional conditions of geological time. In addition, the more competent rocks frequently are fractured and jointed as the result of structural deformations or tectonic movements. Evidence of such joint systems exists in many surface outcrops, and it can be assumed that similar systems occur in many subsurface rocks, although the individual joints may be rather tightly closed due to overburden forces. This paper investigates the effect that an existing fracture in a rock would have on the direction or orientation of an extending or advancing hydraulic fracture when it intersects the existing fracture. The study was conducted on small rock models under triaxial stress conditions. The results indicate that an existing fracture will have little effect on the hydraulic fracture. THE MODEL STUDY The rock model represents an elemental portion of the earth containing an existing fracture which is located at some distance from a borehole from which hydraulic fracture is being extended. A generalized view of a model is presented in Fig. 1. The models were constructed from cement blocks and natural rocks. The various materials tested and some of the physical properties are listed in Table 1. The rocks were cut into rectangular blocks with dimensions of 11/2 X3Y2 X4 to 8 in. An initial slot was cut into the end face of each block along the longitudinal axis normal to the top face. The slot was filled with plastic aluminum along its outer edge to a depth of 1/16 in. A hole of 3/8-in. diameter was drilled into the sealed slot at the center of the end face to serve as an entry port for the fracturing fluid. Existing fractures of various types were simulated in the models. A "hairline" fracture with essentially zero width was created by cutting the model into two parts with a diamond saw and replacing the two parts together along the cut. A finite-width fracture was created by placing a layer of sand grains between the two faces of the cut just described (see Fig. 12). A large open fracture (similar, perhaps, to a vug) was created by cutting the model in two parts and removing a portion of the downstream block to a depth of % in. See Fig. 13. For a fourth

By C. Laird, C. E. Feltner

An investigation into the effect of a material's slip character on its high strain fatigue properties has been carried out using copper and Cu-7.5 wt pct A1 as representative wavy and planar slip mode materials, respectively. In copper, the constant term and exponent in the Coffin-Manson equation, ?EpNf1/2 = const, are unaffected by the temperature of testing or the history of the metal. On the other hand, in Cu-7.5 wl pcl Al, while the exponent is invariant, the constant is increased with respect to copper and increased further with decrease in temperature. The life in Cu-7.5 wt pct A1 is double that of copper at room temperature and about four times at 78°K. Fractoflaphic studies indicate that these diffevences in life are associated with the early stages of cracking. In copper, severe surface rumpling provides crack nuclei at pain boundaries independent of' testing temperature or the history of the metal. In Cu-7.5 wt pct Al, the planar slip mode of deformation prevents grain boundary folding; crack nucleation is therefore mainly transgranular and the increase in life with respect to copper is associated with a prolonged linking-up stage of such transgranulay cracks. At the lower temperature the increased difficulty of cross slip inhibits multiplication of trans-granular cracks and retards the linking-up process, giving a further enhaancement in life. It is expected that such behavior will be found general in materials of wavy and planar slip mode, respectively. STAGE II crack propagation in high strain fatigue takes place by a repetitive process of crack tip blunting in the tension part of a fatigue cycle followed by resharpening of the crack in the compression part.1-3 This mechanism has come to be called the "plastic relaxation process".3 At very high strains (lives to failure less than 103 cycles), most of the life of a specimen is spent in crack propagation by the plastic relaxation process.4,5 Since the differences in the cyclic strain hardening behavior of metals and alloys are comparatively small in this strain range,6,7 the amount of blunting at a crack tip depends primarily on the applied strain amplitude. The rate of crack propagation in this life range is therefore nearly constant with respect to material and temperature of testing. In the longer life portion of the high strain fatigue range (l03 to 103 cycles to failure), a considerable fraction of the lives is spent in crack initiation and Stage I growth. Grain boundaries have frequently4,5,8 been found to be the sites for this growth which is also associated with a surface folding process.4'5 Such folding behavior may also be general in any material having a grain structure and capable of plastic deformation. It has therefore been suggested475 that the universality of the Coff in-Manson law,9'10 constant,* where ?Ep is the plastic strain range and Nf the number of cycles to failure, is reflected in the approximate invariance of both the crack initiation and propagation behavior. It happens that, in most investigations of the phenomena associated with failure,4,5,8 materials with a wavy slip mode have been used as vehicles for the studies, or else "normally" planar slip mode materials have been tested under conditions giving rise to wavy glide deformation, e.g., stainless steels cycled at high temperature.'' The purpose of the present investigation was to determine whether or not different cracking phenomena would occur when the slip mode of a material is planar and if the associated life to failure would be different than that of a wavy slip

Jan 1, 1968

By D. D. Pollock

Many constitution diagrams do not indicate the limits oJ solid solubility of the silver-rich solid solutions below 200°C. Thermoelectric measurements were employed to determine this limit in the nieighborhood of room temperature. The appearance of a second phase causes a discontinuity to occur in the tkevtrroelectric power as a function of cornposition at constant temperature and pressure. This discontinuity was employed to determine the limits of the silver-rich terzinal solid solutions of the Ag-A l, Ag-As, Ag- Bi, Ag--Ge, Ag-In, Ag-Pb, Ag-Sb, and Ag-Sn systenls at 30°C. CONSIDERABLE work has been done on the constitution of binary alloys of silver. The available data have been compiled by Hansen1 and Elliott.2 However, many of the binary diagrams do not show the limits of solid solubility of the silver-rich solutions below about 200° C. This work was undertaken in an attempt to extend these limits to the neighborhood of room temperature . PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pct (by weight) of impurities. The materials were weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony alloys were melted in A1203 crucibles, under a boric anhydride cover, and were poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles; they were also covered with boric anhydride and poured into split graphite finger molds. The $-in.-diam ingots were heated to 750°C and were forged and hot-rolled down to 0.1 by 0.1 in. The wires were pickled in a 25 pct HNO3-75 pct H2O solution to remove any oxygen-rich surfaces. The wires were then annealed at 550°C for 2 hr in a dissociated ammonia atmosphere. They were then furnace-cooled for 20 hr to room temperature in this atmosphere. The wires were cold-drawn to 0.0808 in. diam. The finished wires were again annealed at 550°C in the same manner as in the first anneal. Thermoelectric Power. The thermoelectric power of a single specimen of each alloy was determined against pure silver which contained a maximum impurity content of 0.014 pct by weight. The wire specimens were straightened and then cleaned with ethyl alcohol. They were then reannealed in the same way as the finished wires to assure that any residual stress would be at a minimum level. Previous work has shown that the presence of small amounts of stress has the effect of decreasing the thermoelectric power. The alloy specimen was soldered to the pure silver wire to form the measuring junction. A standard set of copper leads was then soldered to the reference junctions of the thermocouple. These junctions were maintained in separate dewar flasks which contained finely shaved melting ice during the test. The thermal electromotive forces of the thermocouples were measured at four temperatures between 15° and 45°C. A known source of electromotive force was balanced against the output of the thermocouple until a null balance was reached. The data were then expressed in terms of the thermoelectric power at 30°C. The results were then converted to absolute thermoelectric power, s303.3 These data have an average error of less than ±0.2 pct. RESULTS AND DISCUSSION All of the experimental data are given in Table 11. Since the electromotive forces of the binary alloys of silver were determined against the pure silver from which they were made, the resultant thermoelectric powers are only a function of the intentionally added binary elements at the constant test temperatures. This provides a direct measure of the effects of the alloying elements. The absolute thermoelectric power of an alloy of silver is given4 by:

Jan 1, 1968

By W. B. Mather

Of the 61 dikes examined some yielded cassiterite, tantalite, and beryl; eight contained spodumene; and six carried amblygonite. Two mines stockpiled spodumene as a byproduct. Only zoned pegmatite dikes carried lithium minerals. GEOLOGICAL studies have revealed the occurrence of hundreds of pegmatite dikes in northeast Brazil, Fig. I, in the three states of Rio Grande do Norte, Paraiba, and Ceara. Heretofore data have not been available on the possible production of lithium minerals from these areas, and in March, April, and May 1953 the author undertook a reconnaissance survey covering a cross-section of the pegmatite~. Sixty-one pegmatites were examined. The pegmatites of Rio Grande do Norte and Paraiba are located in an arid region (Seratao), and except in the most southerly portion there is a minimum of vegetation and overburden. The region is easily prospected and relatively accessible by jeep or truck. The pegmatites examined in Ceara are in an area of lush vegetation along the flanks of the Jaqueribe River valley. It is therefore more difficult to prospect, and the dirt roads, as a means of access, leave much to be desired. For all practical purposes rail transportation, except in Ceara, is not available. The rocks of the area are composed of Pre-Cambrian schist, gneiss, quartzite, and marbles. They have been intruded by granites, monzonites, and diorites and cut by quartz veins and pegmatites. Pre-Cretaceous erosion reduced the area to a peneplain upon which Cretaceous or younger sandstones were deposited. Recent erosion has left only a few remnants of these younger rocks. In most of the Rio Grande do Norte-Paraiba area the pegmatites were more resistant to erosion than the enclosing schists and therefore stand out in relief. This is not true in the rolling country of Ceara, where the pegmatites lack topographic expression. With regard to structure and lithology, the pegmatite~ of northeast Brazil are divided into two types, uniform and zoned. Of the 61 examined, 19 belong to the uniform and 42 to the zoned type. Uniform pegmatites are normally long, narrow, and tabular, with sharp contacts. They are composed of an intimate mixture of feldspar (microcline or ortho-clase), mica (biotite, phlogopite, or muscovite), and quartz. The grain size5 varies from fine at the contact to coarser in the interior. They are not considered a commercial source of pegmatite minerals, although efforts have been made to produce green beryl of gem variety. This type of dike is often abundant in schists and gneisses close to granite intrusives. The productive dikes — lenticular, pod-shaped, or irregular in outline, with sharp contacts — are of the zoned variety. Zone contacts are gradational, except for those with the quartz core. Zones re identified as follows, see also Fig. 3. Border Zone: This outer zone, in contact with the country rock, is composed chiefly of fine-grained muscovite and biotite, with lesser quantities of finegrained microline and quartz. It is the narrowest zone, usually measurable in inches. Wall Zone: Lying between the border and intermediate zones, the wall zone is composed of medium-grained feldspar (often microcline), muscovite, and quartz. Usually it is the widest zone. Widths of 50 ft were noted. Intermediate Zone: Lying between the wall zone and core, the intermediate zone is composed principally of coarse-grained microcline (occasionally with some orthoclase and albite). It may also carry minor amounts of coarse-grained quartz and fine to medium-grained mica. The width varies from less than 3 ft to more than 30 ft. Core: The center of the dike is composed almost entirely of massive quartz, occasionally with minor amounts of fine-grained muscovite. The width reaches 30 ft. Lithium and other minerals of potential economic value are found in the following zones:

Jan 1, 1955

By Garth M. Crosby

Hugh E. McKinstry (Professor of Geology, Laboratory of Mining Geology, Harvard University, Cambridge, Mass.) Pre-Cambrian age for the Coeur d'Alene mineralization, as indicated by isotope studies and recently discussed by Silverman, Long, and Kulp' would explain some features of the mineralogy of the district that have long been a puzzle. In the Silver Belt, especially in the Sunshine mine, lead-zinc min erali zation passes downward into tetrahedrite ore. Although commercially speaking this is a rich silver zone, the silver is, quantitatively, a mere impurity amounting to a small fraction of 1 pct. In effect the zonal change is from lead-zinc down into copper mineralization—-the usual zonal change that occurs in many districts. In the Burke-Mullan portion of the district, on the other hand, lead-zinc ore does not pass downward into copper mineralization of the Sunshine type. Instead, pyrrhotite appears in depth while the tenor in lead and zinc declines. The change occurs at increasingly greater depth away from the Gem stocks, deepening irregularly by some 3000 ft within two to four miles. As noted by Crosby, biotite, grunerite, and garnet appear in the deep zone. The marked difference between this apparent zonal change and the more nomal change to a copper zone is quite explainable if already existing pre-Cambrian veins have been locally metamorphosed by a Tertiary intrusive. The chief obstacle to this explanation is the evidence that mineralization cuts Laramide intrusives, but evidence on this point is conflicting as indicated by Crosby's observations and summary. This is not the first instance of a problem in determining the time-relationship of mineralization to a spatially associated intrusive. At the Noranda mine veins of chalcopyrite extend into a diabase dike which apparently cuts the ore, although Price2 concludes that the ore is later. However, at the Normetal mine diabase of a similar dike is thought3 to intrude the orebody but is cut by stringers of chalcopyrite. In the Sullivan Mine, B. C.,4 galena follows a fracture in a larnprophyre dike which, itself, cuts the main orebody. In the Sudbury district dikes of olivine diabase are clearly younger than the nickel ore, yet where they cut the Creighton orebody they contain stringers of chalcopyrite. In the laboratory, Hawley5 has developed veinlets of sulfide (chalcopyrite) it] silicate gangue by heating specimens of ore in a stream of H2S at 410 °C. From this and other evidernce. it seems clear that sulfides can be transferred from one site to another — at least through short distances — at temperatures well below their melting points. It would seem then that even if sulfide Mineralization in the Gem stocks can be shown unequ ivocably to be later than the intrusive the possibility of "remobiliza tion" need not be more than local. Thus the zonal relationships are quite in accord with a pre-Cambrian age for original deposition of the lead, zinc, copper, silver, and uranium in the Coeur d'Alene district. REFERENCES 1. A. Silverman, A. Long, and J. L. Kulp: Discussion of: The Gem Stocks and Adjacent Orebodies, Coeur d'Alene District, Idaho. Mining Engineering, May 1960, pp. 470-471; AME Trans., 1960, vol. 217, p. 117. 2. Peter Price: Geol. & O. D. at the Home Mine, Noranda, Quebec. Can. Inst. M & M Bull 263, 1934, p. 108; also,Trans. CIMM 1939, pp. 108-140. 3. w. L. Brown Nometal Mine in structural Geology of Canadian Ore Deposits, Montreal, 1948, p. 690. 4. C. O. Swanson and H. C. Gunning: Geology of the Sullivan Mine. Can. Inst. Mining & Met. Trans. vol. 48, 1945, p. 653. 5. J. E. Hawley: Heat Effects on Sulphides and Possible Applications. Univ. Toronto Studies, Geol. Ser. No. 46, 1941, p. 34.

Jan 1, 1961

By B. F. Decker, J. H. Keeler, W. R. Hibbard

Textures of hot-rolled, of cold-rolled, and of cold-rolled and annealed zirconium sheets were determined by use of an X-ray spectrogoniometer. All textures showed a tilt of the basal planes 240" from the rolling plane about the rolling direction. Deformation textures showed the [1010] direction to be approximately in the rolling direction. After recrystalliza-tion, the 111201 direction was approximately in the rolling direction. This texture was sharpened by annealing above the allotropic transformation. Textures of sheet produced by alternately cold rolling and then annealing were less strongly oriented than sheets that underwent severe deformation without intermediate anneals. THIS study of the deformation and annealing textures of high purity zirconium was carried out to supplement an investigation of zirconium and zirconium-base alloys. The spectrogoniometer method of pole figure determination was used and yielded more detailed and precise information than the photographic techniques used by previous investigators. Earlier investigations of the rolling textures of hexagonal metals titanium,1,2 beryllium," and zirconiumL having a c/a ratio slightly less than 1.6 disclosed a rotation of the basal planes from the rolling plane about the rolling direction so that the basal poles were inclined toward the transverse direction, and with one exception,& the [1010] direction was found parallel to the rolling direction. Similarly, hot rolling produced a spread of the basal poles in the transverse direction,2,3,5 With the [1010] direction parallel to the rolling direction. The textures of these metals after recrystallization differ somewhat from each other although still exhibiting the transverse rotation of the basal poles about the rolling direction. Zirconium" was found to have the [1120] direction in the rolling direction, beryllium" continued to have the [1010] direction in the rolling direction, and titanium' was shown to have the [1010] direction in the rolling direction (the cold-rolling texture) when annealed at 1000°F, changing to the [1120] direction in the rolling direction when annealed at 1500°F. It was suggested2 that the titanium retains the deformation texture after re-crystallization, and preferred grain growth at higher temperatures produces the second texture. Annealing above the allotropic transformation temperature did not appreciably change the high temperature recrystallization texture for titanium.' Coarsegrained zirconium showed more spread" in the transformation texture than in the recrystallization texture. The material used in this investigation was crystal-bar zirconium prepared by the iodide process. The major impurity was hafnium which was less than 0.3 pct. The composition obtained by spectro-graphic analysis is given in Table I. The hot-rolled specimen was prepared from a 50-g button of zirconium arc-melted in a water-cooled crucible under an argon atmosphere. This button was enclosed in a welded sheath of soft iron and the ensemble was rolled at 825°C. After each pass the sheath was put back into the furnace to allow it to return to the desired temperature. The zirconium ingot was reduced in this manner to a thickness of about 0.035 in., a reduction of approximately 90 pct. The sheet after removal from the sheath was alternately polished and etched to a thickness of 0.001 in. Cold-rolled specimens were prepared from crystal bar by a series of reductions of approximately 0.010 in. until the sheet reached a thickness of 0.010 in. after which it was cold-rolled to 0.001 in. thickness between sheets of alloy steel. The total cold reduction amounted to about 99.8 pct. Specimens were annealed in an evacuated Vycor or quartz tube. The transmission pole figures were obtained by the quantitative method of Decker, Asp, and Harker6 modified by Geisler7 using an X-ray spectrogoniometer with Cu Ka radiation. Unless otherwise specified all four quadrants were examined with 5" increments along the radius of the pole figure. Absorption corrections were made for changes in length of the X-ray path through the sample as inclination of the

Jan 1, 1954

By William H. Bassett

COPPER is the world's most important non-ferrous metal, and brass is the most widely used non- ferrous alloy. Much of the utility of each may be credited to the work of metallurgists who have constantly improved the quality of the metals and alloys and the methods of fabrication. Standing in the front rank among these is William Hastings Bassett, the newly elected president of the Institute. Mr. Bassett, ,who is technical superintendent and metallurgist for the American Brass Co.,

Jan 1, 1930

By Scott Turner

IT has been considered that the training of an engineer is too often vocational training; that it is a pity all engineers cannot have had a period of liberal training before taking up' pure engineering. Offhand, the so-called liberal courses should bring more ready adaptability to deal with the unexpected, to face with assurance situations which have had no parallel in one's experience, and to move without hesitation under conditions which were heretofore unknown to one, than the specialized course in mining engineering. We hear increasing talk as to the necessity of making the engineer articulate and bringing him into public life. The social implications, and responsibilities of engineering are pointed out, as of equal importance with the prodigious marvels of engineering ingenuity. You often read of this as the logical result of the in¬creasing consciousness of the engineer as to his rela¬tive position in our modern industrial civilization. , Some wag has noted that man is the noblest work of God, but that man is the only one who has said so. Perhaps engineers are the only claimants as to the necessity of their going in for public life and service; at any rate, some liberal educators' still maintain that a well-rounded general education is the better training.

Jan 1, 1930

By M. L. Hammond, G. M. Bowers

Silicon dioxide films have been prepared on silicon wafers by the oxidation of SiH, near 400°C. Results previously reported by Goldsmith and Kern7 have been qualitatively corrobovated using a system of different geometry, and significantly greater deposition rates have been achieved. The deposition rate is independent of thickness and nearly independent of the O2/SiH, ratio over a wide range; however, the rate is strongly temperature-dependent. The structure of the deposit depends upon the cleanliness of the substrate, and the electrical field strength of the deposited oxide depends upon the nature of the electrodes. MULTILEVEL interconnects in integrated circuits using aluminum metallization require an insulator that can be deposited at low temperature. Because the A1-Si eutectic is only 577°C, the maximum deposition temperature must be below about 500°C to prevent reaction of the aluminum with the silicon and with other materials in the integrated circuit. Many methods of depositing insulating films of SiO, and other dielectrics have been reported'-6 but the technique described by Goldsmith and Kern7 offers the simplest method of preparing SiO, films. The technique involves the reaction of SiH, and 0, to form SiO, films in the 300" to 500°C temperature range. Previous work using this gas system has been reported8 and the initial development work at Philco Microelectronics was done at the East Coast R&D Laboratories. 9 This paper corroborates some of the results of Goldsmith and Kern,7 shows that much higher deposition rates can be obtained than previously reported, and presents some observations on the structure of deposited SiO, films. EXPERIMENTAL CONDITIONS Fig. 1 is a schematic drawing of the apparatus used in this study. It differs from that of Goldsmith and Kern in that 1) the gases are mixed before they enter the reaction chamber, 2) there is no fritted glass diffuser, and 3) the wafers are stationary during deposition. The control thermocouple was in a well located 0.06-in. from the substrate, and three gas supplies were used: 1 pct SiH4 in N 2, O 2, and N 2. Water vapor must be excluded from the plumbing to prevent the formation of colloidal SiO, and the SiH4 must be diluted with an inert gas because SiH4-0, mixtures are extremely flammable above about 4 pct SiH The wafer temperature was determined by attaching a thermocouple to a test wafer and the temperature was maintained to +5 C. The conditions used in this investigation are listed in Table I. The temperature range was chosen for compatibility with the A1-Si system. The volume ratio of 0, to SiH4 is the actual volume of 0, delivered to that of SiH4, taking into account the initial dilution of the SiH4. This ratio, which was used by Goldsmith and Kern,7 is a useful indicator of the experimental conditions. The active/inactive ratio is the ratio of the volume of active gases, SiH4 and O2, delivered to the volume of dilution gas. The active/inactive ratio is an important parameter to specify for deposition rate determinations since it determines the amounts of reactants that arrive at the sample per unit time. Fairly high dilution ratios were necessary to achieve uniform deposits of SiO,. Most of the process characterizations were performed on the polished (111) face of 3 to 5 ohm-cm, n-type silicon wafers which were 0.009 in. thick; but the data approximately apply to deposition of SiO, on thin films of aluminum. It is difficult to obtain accurate deposition rate data over aluminum films because of coarsening the aluminum surface during exposure to 300" to 400°C. The deposited SiO, film fol-

Jan 1, 1969

By G. D. Cremer, J. J. Cordiano

ALUMINUM powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, how- ever, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and aluminum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. 4 second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age- hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders, is probably the significant factor in our failure to obtain strong sintered pieces. METHODS OF PRODUCING THE POWER Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By John M. Hartman

On May 19th, 1857, an English patent was granted to E. A. Cowper for heating air or other gases under pressure by means of a regenerator inclosed in an air-tight iron case, having between the regenerator and case a lining of brick. This patent provided for heating the stoves by a separate fireplace, or by gas direct from the blast furnace. A number of forms of interior arrangement of the brickwork are shown in the drawings; also hollow poppet valves with hollow stems, and a pipe inside of the stem for circulating the water; the valve seats have coil cast in them for water circulation to keep them cool; slide valves, with snake coil cast in the discs, are shown, and the use of cold air for cooling the valves is also described. The combustion-chamber of these stoves was central, and openings mere provided at the top and bottom to get into the stoves. These Cowper stoves are all circular in section. November loth, 1865, an English patent was granted to Thomas Whitwell for regenerative stoves for heating air or gas, provided with cleaning openings at the top and bottom capable of being closed with firebrick plugs and doors. The drawings show a rectangular stove inclosed in an iron case. The interior brickwork has numerous upand-down passages through the stove, but there is no claim on the interior construction. March 3d, 1868, an English patent was granted to Charles Cochrane for a slide valve to be subjected to high heats. The disc of this valve was hollow, and had a circulation of water through it by the two hollow stems that operated it. The valve-seat was detachable and had a coil cast in it, through which water circulated. The valve and seat were placed on an incline to the body to cause the valve-disc to lie on the valve-seat. A cap was placed on the bottom of the body to get at the interior readily. January 5th, 1870, an English patent was granted to Siemens, Cowper and Cochrane for the construction of regenerators in firebrick stoves, with numerous vertical passages of sufficient size to allow a brush to pass through and clean them. These passages had slight projections on the sides to tarn the air over and over as it passed through. A claim also covered the use of horizontal passages connected at each end alternately, and the use of blasts or jets of air,

Jan 1, 1880

By Joan M. Hartman

ON May 19th, 1857, an English patent was granted to E. A. Cowper for heating air or other gases under pressure by means of a regenerator inclosed in an air-tight iron case, having between the regenerator and case a lining of brick. This patent provided for heating the stoves by a separate fireplace, or by gas direct from the blast furnace. A number of forms of interior arrangement of the brickwork are shown in the drawings; also hollow poppet valves with hollow stems, and a pipe inside of the stem for circulating the water; the valve seats have coil cast in them for water circulation to keep them cool; slide valves, with snake coil cast in the discs, are shown, and the use of cold air for cooling the valves is also described. The combustion-chamber of these stoves was central, and openings were provided at the top and bottom to get into the stoves. These Cowper stoves are all circular in section. November 10th, 1865, an English patent was granted to Thomas Whitwell for regenerative stoves for heating air or gas, provided with cleaning openings at the top and bottom capable of being closed with firebrick plugs and doors. The drawings show a rectangular stove inclosed in an iron case. The interior brickwork has numerous up-and-down passages through the stove, but there is no claim on the interior construction. March 3d, 1868, an English patent was granted to Charles Cochrane for a slide valve to be subjected to high heats. The disc of this valve was hollow, and had a circulation of water through it by the two hollow steins that operated it. The valve-seat was detachable and had a coil cast in it, through which water circulated. The valve and seat were placed on an incline to the body to cause the valve-disc to lie on the valve-seat. A cap was placed on the bottom of the body to get at the interior readily. January 5th, 1870, an English patent was granted to Siemens, Cowper and Cochrane for the construction of regenerators in fire-brick stoves, with numerous vertical passages of sufficient size to allow a brush to pass through and clean them. These passages had slight projections on the sides to turn the air over and over as it passed through. A claim also covered the use of horizontal passages connected at each end alternately, and the use of blasts or jets of air,

Jan 1, 1880

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By Nathan C. Rockwood

The title of this paper, I understand, was suggested by professional mining engineers as an opportunity for someone to pose problems rather than to offer solutions for them, but the paper will merely attempt to pose some of the production problems of the mineral aggregates industry in such manner as to create professional interest in their solution by the mining engineer, geologist, geochemist and the metallurgical engineer versed in mineral-dressing technique. Definition of Mineral Aggregates " Mineral aggregates" may be defined as fragments of any rock or mineral used to supply bulk or volume or substance for a given purpose. For example, mineral aggregates are used in portland-cement concrete to provide bulk with the expenditure of the least feasible amount of cement binder. Mineral aggregates are used without port-land cement or bituminous binder in highway and railway roadbeds to provide substance, to carry loads. provide aggregates are used in filters for water and sewage, to provide substance for the liquid to trickle through. These are only a few typical uses of mineral aggregates. For all these uses, strength, toughness, resistance to abrasion, and durability are usually prime requisites; so, while theeretically mineral aggregates may be of any mineral composition, what really is desired is a mineral composition as nearly inert under the conditions of use as anything of earthly origin can be. Exploration and Possibilities of Development The distribution of deposits of mineral aggregate is universal, since almost any part of the earth,s crust can be used; even the top soil is sometimes used in stabilized surfacing for highways or airport runways. Nevertheless there is ample opportunity for exercise of the talents of the mining engineer and the geologist in finding the particular deposit that will be most economical to develop, keeping in mind such considerations as: (i) quality and mineralogical characteristics of the material; (2) size and permanency of the market; (3) final cost of opening and development of the deposit; (4) selection of location of plant; (5) methods and costs of distribution of the product in comparison with both present and possible future competition; (6) selection of the proper type of operating equipment; (7) estimation of probable waste products and their disposal. These are typical but there are other considerations also. Because profit margins are far smaller than in any comparable mining operation, it is all the more logical to assume that a higher degree of expert knowledge is desirable to make a success of a mineral-aggregates business. The industry has much engilleering talent in its operating branch, but it lacks, to a considerable degree, engineering talent with experience

Jan 1, 1948

By C. D. Hall, F. E. Dollarhide

Conventional static tests of fluid-loss agents do not realistically simulate conditions in a fracturing treatment. The dynamic tests reported here show that fluid-loss volume is better represented as proportional to time, rather than as the square root of time. This leads to a different equation for fracture area. The leak-off rate increases with increasing shear rate at the fracture wall, but appears to approach a limiting value. Pressure effects are minor. Spurt loss ordinarily is not affected by the flow velocity in the fracture and is inversely proportional to concentration of agent. The filter cake, once it is well established, is resistant to damage by the flow of plain fracturing liquid (without fluid-loss agent). The latter two findings indicate that a treatment employing a high-concentration spearhead followed by plain fluid can offer a more economical treatment under suitable conditions. INTRODUCTION The successful design of hydraulic fracturing treatments depends on accurate knowledge of the fluid-loss properties of the fracturing fluid. Howard and Fast,' in giving the basic equation relating fracture area to fluid and treating parameters, described three mechanisms which might control the rate of fluid leak-off from the fracture. One mechanism usually is dominant in a given well treatment. For each mechanism, the leak-off velocity is inversely proportional to the square root of time, and the proportionality constant is designated as the fracturing-fluid coefficient. For the wall-building type of fluid-loss agent, the coefficient is determined by a filtration test in a pressure cell, usually with a rock wafer or core as the filter medium. In these static tests, the cumulative volume generally is proportional to the square root of time, after an initial spurt volume. The static-fluid-loss test is not representative of the con,-&tions under which a fluid-loss agent performs in a fratturing treatment. The marked difference between the dynamic- and static-fluid-loss behavior of drilling fluids reported in the literature2,3 implies that dynamic testing is also needed with fracturing fluids. We have therefore undertaken a study of the dynamic-fluid-loss behavior of fracturing fluids. The testing apparatus has also afforded opportunity to evaluate the resistance of the filter cake to removal or damage by flowing fluid containing no fluid-loss agent, with and without sand. The results of these studies offer a means for more accurate evaluation of fluid-loss agent performance, and point the way to a "spearhead" fracturing technique which may offer more economical treatment for some wells. EXPERIMENTAL METHODS The dynamic-fluid-loss testing method is applicable to any type of wall-building fracturing fluid. The present study aimed first at finding what phenomena are involved, and therefore has been limited in the number of materials tested. All of the results specifically reported herein are for kerosene containing a commercial solid fluid-loss agent, which is commonly used at 50 lb/1,000 gal of oil. Another agent in liquid form, used usually at 20 ga1/1,000 gal oil, has shown all the same phenomena in dynamic tests, and generally the same level of fluid-loss control as the solid agent. The dynamic-fluid-loss core cell used in all tests is shown in Fig. 1. The fracture was simulated by the an-nulus between a 2.03 in. OD sandstone core and the surrounding pipe. Annulus widths of 0.234 and 0.117 in. were used, and the core was 3.5 in. long. The annular geometry provides a uniform fluid velocity and a well-defined shear rate over the entire filtering surface, and permits a large filter area (144 sq cm) in a reasonably compact cell. The leak-off fluid passed into a 0.5 in. diameter axial hole in the core. A hollow steel rod through this hole was threaded into a rounded "streamliner" upstream of the core, and into a mounting stud downstream. The streamliner and the stud had the same outside diameter as the core. In all tests except those where sand was circulated, the mounting stud had protruding rings which constricted the annulus, to minimize any tendency for channeling of the fluid to the side exit port. The ends of the core were sealed by Neoprene, steel and Teflon washers. The leak-off fluid was conducted from the hollow rod to an exit tube, through a metering valve (a fine-pitched needle valve) and a quick-opening toggle valve in series, and into graduated cylinders for volume measurement; Two separate circulating systems were used in the experimental program. The extensive initial testing was done at 50 to 150 Psi. The fluid was circulated by a variable speed Moyno pump, and the flow rate was read by a rota-meter flow meter. The filtration Pressure was supplied by holding a back-pressure with a throttling valve. The discharge streamcould be diverted into any of four sections

Jan 1, 1965

By F. M. Waring

produced when zinc is substituted for a certain amount of tin are decidedly unsatisfactory. The substitution of aluminum for tin is entirely impractical, and such castings are worthless. This does not, however, exhaust all the possibilities of substituting other metals for tin in the copper-tin-lead alloys, but it is my opinion that the substitution of any other metals, in those alloys, can be made only by sacrificing the quality of the alloy. The possibility of substituting alloys of an entirely different type presents an attractive field for research. The copper-tin-lead alloy has attained its position as the most desirable bronze bearing alloy, but this does not mean that some other alloy may not be found which may give equally good or better results. In the search for such a substitute alloy it should be borne in mind that a bearing metal should possess the following properties: (1) It should be sufficiently rigid to support the load or resist the impact, but yet not so brittle that it will easily crack. (2) It should have as great a yielding or plastic nature as is consistent with its ability to support the load or resist the impact without deformation of the bearing as a whole. (3) The ideal structure combines a hard matrix to support the load and a softer metal or alloy contained within such matrix, to permit the bearing surface to adjust itself to irregularities of service. (4) It should be easy to handle in the foundry and machine shop. (5) It should be capable of being remelted without deterioration. (6) For use in babbitt-lined bearings, it should be capable of being tinned, so that the babbitt can be applied thereto. (7) It should have good heat conductivity in order to dissipate the heat generated by friction. Pennsylvania Railroad Anti-friction and Bell Metals F. M. Waring," Altoona, Pa.—Thc necessity for conserving tin has recently been very forcibly brought to the attention of all consumers, and efforts are now being made to reduce the tin content in certain alloys or to substitute other alloys not containing tin. The approximate composition of the non-ferrous alloys in general use on the Pennsylvania Railroad are given in the accompanying table. Phosphor bronze is used principally for rod bushings, main-rod brasses, and crosshead shoes. Ex. B bronze is used to a small extent for backs of car and coach bearings, but the majority of these are now made of the car-journal bronze, which contains, on the average, about 5 per cent. tin.

Jan 1, 1919

By K. G. Wikle, W. W. Beaver

The factors which control the rate of dissolution of pure gold in cyanide solution were studied both directly and through measurement of solution the current-potential curves for the anodic and cathodic portions of the reaction. The mechanism of dissolution is probably electrochemical the reaction in nature, and the rate is determined by the rate of diffusion of dissolved oxygen or cyanide to the gold surface, depending on their relative concentrations. The significance of the results and the effects of impurities are considered. ALTHOUGH the dissolution of gold in aerated cyanide solutions has been used as an industrial process for treatment of gold ores since the late nineteenth century, the factors which determine the rate of the reaction have never been identified unambiguously. Studies of the rate of dissolution by Maclaurin,1 White,2 Christy,3 Beyers,4 Thompson,6 and others are contradictory in their conclusions; some claiming that diffusion of the reactants to the gold. surface controls the rate, and others that the chemical reaction is inherently slow and related to high activation energy for the reaction. Christy3 and 'Thompson" both suggest that the reaction is electrochemical in nature and that the dissolution of gold proceeds at local anodic regions while the oxygen is reduced at cathodic regions on the gold surface. Although their studies are ingenious and do indicate an electrochemical reaction under the conditions of study, their experiments were of limited nature and failed to identify the rate-controlling process in the system. The importance from an industrial viewpoint of a knowledge of the mechanism and rate-controlling factors in gold dissolution can be illustrated as follows: If the rate is controlled by a slow chemical reaction rather than by diffusion of the reactants, then an increased temperature should have a marked accelerating effect; agitation of the slurry should have no effect on rate: and increased concentration of reactants should cause acceleration of the rate. If the rate is controlled by the diffusion of one or the other of the reactants to the gold surface, then increased agitation should increase the rate; increased temperature will increase the rate, but not as much as for the case of a slow chemical reaction; increased concentration of the reactant which is diffusion limited will increase the rate; and the concentration of other reactants should be without effect on the rate. It may be concluded that for design of a commercial process for gold leaching, the rate-controlling factors of the reaction should be understood so that an intelligent choice of the conditions of agitation, temperature, and reactant concentration may be made. The experiments described here lead to the unambiguous conclusion that in a system of pure gold and a pure aerated cyanide solution the rate of dissolution is controlled either by the rate of diffusion of dissolved oxygen or cyanide to the gold surface, depending on the relative concentrations of each. There is also ample, but not conclusive, evidence that the mechanism of the reaction is identical to that of electrochemical corrosion. The practical significance of these conclusions will be discussed later in the paper. Experimental The experimental method used in this work was to employ an electrolytic cell which performed the overall gold-dissolution reaction, and to study the anodic and cathodic reactions of this cell as to their nature and the rate-controlling factors. Simple experiments on the rate of dissolution and the potential of the dissolving specimen also were performed under conditions of agitation, temperature, and concentration identical to those used in the electrode studies. Analysis of the electrode studies by well established theories of electrochemical corrosion were made, and the results were found to bear a one-to-one relation with actual rate and potential measurements. Electrode Studies: The Anodic Reaction: The gold specimen used for all of the electrode studies and the rate determination consisted of a sheet of 99.99 + pct Au wrapped around a lucite rod and sealed at the edges with plastic cement, thus forming a cylinder of gold of known and constant area (8.0 sq cm). The lucite rod was threaded into a brass spindle which could be rotated at speeds of 100, 300, and 500 rpm. For the electrode studies electrical contact between the gold cylinder and the brass spindle was made by means of a gold strip covered with plastic. The anodic dissolution of gold was studied by immersing the electrode in a solution containing known concentrations of KCN and KAu(CN)2 but free of oxygen, and by passing an anodic current through the gold electrode. The pH of the solution was maintained between 10.5 to 11.0 in these and all other tests by addition of KOH. The pH was measured before and after each test by means of a glass-elec-

Jan 1, 1955