Search Documents

By John H. Bell

R. B. T. KILIANI, New York, N. Y.-I wish to present some figures based upon actual observation extending over a few months time which seem to prove the author's conclusions. It is a comparison of two machines operating on the same ore, in the same plant, one taking the undersize of ½ -in. screen and the other taking the undersize of 8-mesh. Each of the machines was first operated as a pebble mill, with flint pebbles, in open circuit, then with metal pebbles in open circuit and, finally with metal pebbles in closed circuit. For the first case, the percentage of oversize on 48-mesh, Tyler screen, in the discharge, varied, in the mill taking ½ -in- feed, from 37.2 to 19.9 per cent. The second mill, taking the 8-mesh feed, had a variation in oversize on 48-mesh, from 36.8 per cent: to 0.5 per cent.; so it is seen there is considerable variation in these figures. I have computed the tons per kilowatt-day reduced through 48-mesh for each machine under each one of these conditions, giving 6 sets of figures. The first of these I called 1.0 and determined the ratio of the others to this.. In the snipe way, I figured the relative mechanical efficiency according to Kick's law, using' the figures given by Mr. Taggart in his paper, for ordinal numbers of the Tyler screens. I have also figured the efficiency in mesh-tons per horsepower according to Gates' method by plotting the screen analyses of feed and product and multiplying the area by a constant dependent on the scale used. The commercial efficiency of tons per kilowatt-day reduced through 48-mesh checks very closely with the efficiency by Rittinger's law, within 1 per cent. except in one case. By Kick's law, the efficiency checks fairly closely, within about 5 per cent., with the commercial efficiency of the mill grinding feed, but when we start to grind a finer, 8-mesh material, and especially grinding very fine; with a

Jan 4, 1917

By H. Case Willcox

AERIAL photographic surveying and mapping is not new or unknown to geologists. However, it has been utilized but little before, principally because it is only within the last few months that practical means of adapting this method to the requirements of petroleum companies have been discovered. No American aerial survey company has taken up aerial surveying and mapping as an engineering service to be offered to petroleum companies and their geologists for use in undeveloped and jungle-covered petroleum areas. This method of surveying and mapping, however, is used by the War Department, the U. S. Reclamation Service, and Geological Survey, and the corresponding Departments of the Canadian Government. ADVANTAGES OF AERIAL PHOTOGRAPHIC SURVEYING AND MAPPING The advantages of aerial photographic surveying and mapping to petroleum companies and their geologists are many. One of the most valuable is presented in the very first phase, or the exploration period. It is assumed that, when convinced that petroleum possibilities are present, a petroleum company has secured a concession of 8000 sq. mi. of unexplored area in Eastern Venezuela. The company may either have the entire area surveyed and mapped by the aerial photographic method, or send its chief field geologist up in an airplane so that he, from-an aerial reconnaissance, may reject certain portions that, for geological reasons, the company would not be interested in. He will then point out the regions that are to be surveyed and mapped. After the air-work is completed, the results are brought down, developed, and printed; then the resulting "contact prints" are given to the field geologist. They may be roughly assembled to give a general idea of the property in its entirety, or they are in shape to be examined in adjoining pairs under the stereo-scope. With this instrument, the geologist is enabled to make a minute examination of surface indications. The work of assembling and constructing a complete general or detailed map, according to the scales desired by the petroleum company and for the later office use, is continued by the aerial photographic company.

Jan 3, 1925

By S Bankoff

INCE1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. [ ] In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (-200 mesh) and 50 c.c. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments c through g are more insoluble than lead carbonate, there- [ ] fore should prevent the formation of lead carbonate on the galena surface. In experiment i the calcium oxalate, which presumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments j through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1941

By C. E. Ells, A. Sawatzky

The effect of neutron irradiation on tensile properties of the Zr-2.5 wt pet Nb-0.5 wt pet Cu alloy has been evaluated for integrated neutron fluxes up to 3 x 1020 n per sq cm (E > 1 Mev). Specimen temperature during irradiation was normally 300°C. The material was studied both in annealed and in quenched and aged conditions. When the alloy (fab-ricatedfrom sponge zirconium) is quenched from a temperature =40°C below the a + ß/ß transformation and aged 6 hr at 535oC, neutron irradiation up to the maximum studied has little effect 071 reduction in area, although there is a drop in uniform elongation and the yield strength is increased by = 25 pct. Conversely, irradiation of the alloy in an annealed condition can result in much greater changes in properties, with yield-strength increases of up to 200 pet. The dose dependence of irradiation hardening obeys the saturation equntion proposed by Makin and Minter to explain hardening in copper and nickel: Act = C[1 - exp(-Døt)/1/2 A rnodel is proposed to explain the effect of niobium content and metallurgical condition on irradiatiotz behavior. THE Zr-Nb alloys form a class of material susceptible to marked strengthening by quench and age heat treatment. With niobium concentrations as low as 2.5 wt pet, strengths can be developed which are double those of annealed zircaloy-2.1 Since the neutron-capture cross section of the Zr-2.5 wt pet Nb alloy is nearly identical to that of Zircaloy-2, significant gains in power-reactor neutron economy could be obtained by replacing stressed in-reactor components of Zircaloy-2 with the heat-treated Zr-Nb alloy. When the solution heat-treatment temperature is in the high (a + ß) phase, then the tensile properties of the quenched (and aged at 500°C) material have been shown to be relatively insensitive to neutron irradiation.1-3 Addition of small quantities of copper to the binary Zr-2.5 wt pet Nb alloy gives a useful reduction to the corrosion rate in air and carbon di- oxide,&apos; and a ternary alloy of composition Zr-2.5 wt pet Nb-0.5 wt pet Cu was chosen for one component in the Douglas Point Reactor. This application utilizes both the corrosion resistance to a moist air-carbon dioxide environment and the strength developed by a quench and age heat treatment. By suitable choice of solution heat treatment and aging temperatures, tensile properties of the ternary alloy can be made nearly identical to those considered as optimum for the binary alloy. One effect of the copper addition, however, is to give marked changes in the aging kinetics of the alloy.&apos; For this reason, it appeared that neutron irradiation might promote overaging in the ternary alloy, particularly at the elevated service temperature (=300°C). This paper describes the effect of neutron irradiation on the tensile behavior of the Zr-2.5 wt pet Nb-0.5 wt pet Cu alloy in several metallurgical conditions pertinent to its use as a reactor material. The metallurgical conditions included those for which aging occurs in the unirradiated material, and fully annealed conditions for which a higher degree of thermal stability could be expected. 1) EXPERIMENTAL Two batches of alloy were used, both made from sponge zirconium. The fabricator&apos;s analysis of principle constituents showed no significant difference between the two batches, Table I. The rod material was rolled to 1.5 in. diam, and then swaged to final sizes of 0.5 to 0.375 in. diam at nominal temperatures of 785" and 625°C for the AM and AS batches, respectively. Subsequent hydrogen analyses at CRNL confirmed that the hydrogen concentration of the as-received rod was indeed <20 ppm. However, it was found that the (a + ß)/ß transus for the AM material was approximately 25°C lower than that of the AS material, indicating rather more difference in oxygen concentration than given in Table I. Except for a small difference in yield-point behavior, the tensile prop-

Jan 1, 1965

By E. R. Helderman, C. Y. Ang, C. C. Nealey

Beryllium-base alloys have been successfully p7.-epared by the liquid-phase sintering technique. Depending orz the composition and amount of the intended liquid please, microstructures either single -phase or duplex in feature with randomly oriented grains have been obtained. Qualitative and semi-qualitative determination of distribution of alloying elements md microsegregations in some experi)uzental alloys haue been made by electron-micro-probe analysis in conjunction with microliardness testing and standard metallography. Tensile tests reoealed that some conzpositions possess attractive elastic properties with Young&apos;s mot1uli greater than 40 X 10&apos; psi. In powder metallurgy, liquid-phase sintering is a process or phenomenon that has proven to be of practical value. For example, the heavy metals such as tungsten-copper-nickel, high-strength heavy gyro alloys,&apos; heavy-duty electrical contacts,&apos; and tungsten carbide tool materials are all products of liquid-phase sintering. Mechanisms involved in liquid-phase sintering, however, are not completely understood. Questions regarding the exact roles played by rearrangement of particles, liquid/vapor surface energy, solution and precipitation, and so forth, have not been completely answered. Evidence has been cited3 that at least volume shrinkage in the densification process is diffusion-controlled. It is possible that the predominant mechanisms for the complete densification and grain growth in a liquid-phase sintered system depend primarily on the alloy systems involved, in addition to processing conditions. Despite the lack of sound understanding of the mechanisms of the process, liquid-phase sintering has been and is being used to advantage either to synthesize microstructures for their special properties or to prepare alloys which are difficult to form by fusion process. Liquid-phase sintering of beryllium alloys was first attempted by Jones and Williams.4 They first tried infiltrating beryllium with magnesium, and then succeeded in preparing the alloy by sintering Be-Mg powder compact in molten magnesium bath. This investigation resulted in the identification of some Mg-Be intermediate phases. Crossley et a1.5 also used liquid-phase sintering technique in an attempt to produce ductile beryllium alloys for structural applications. The major liquid-phase components investigated by Crossley et al. were aluminum and silver with minor additives of germanium, calcium, lanthanum, cerium, and yttrium. The lack of wetting and the bleeding out of liquid phase were the difficulties encountered during experimentation. According to Hodge,6 the two compositions investigated by Crossley, which showed some promise based on compression tests, involved large amounts (over 35 wt pct) of silver, thus making them too heavy to be of practical interest to the aerospace industry and military users. The present investigation was prompted by the search for light-weight (density less than aluminum) beryllium alloys exhibiting small anisotropy in physical properties for precision inertial navigation instrument applications. In addition to isotropy, good structural properties such as high elastic modulus or desirable combination of mechanical and physical properties are also objectives of this investigation. The technique of liquid-phase sintering was chosen for its versatility in producing either duplex or homogeneous microstructures. This report is concerned with the use of copper and aluminum, with or without silicon addition, as the intended liquid phase, and the resultant micro-structures and some physical properties of the beryllium alloys. Qualitative and semiquantitative electron-microprobe analyses of some of the alloys are presented to illustrate the usefulness of this microanalytical technique for the identification of microconstituents and their distribution. EXPERIMENTAL PROCEDURES The beryllium powder used was -200 mesh Brush Beryllium Co. QMV NP-50 grade. Typical chemical analysis of the powder is shown in Table I. Commercial high-purity copper, aluminum, and silicon powders all screened to —100 mesh were used as additions. Mixed powder compositions were ball-milled in ceramic jars for 1/2 hr to ensure thorough blending. Milled powder was loaded either in 3/4-in.-diam button die or in Metal Powder Association flat tensile specimen die and compacted under top and bottom pressure. No lubricant or organic binder was used. Sintering was carried out in a quartz tube under a vacuum of 50 to 100 µ pressure. Surface hardness and some microhardness readings were taken on sintered specimens. Sintered density was

Jan 1, 1965

By H. B. Charmbury, D. R. Mitchell

Recovery of fine coal from solids reporting to wash water has become increasingly important. These solids range from about 28 mesh to 0 and constitute 3 to 7 pct by weight of the feed tonnage to a coal preparation plant. In the past they were usually wasted to streams, but present clean stream legislation makes it necessary to remove them from the wash water and, if economically possible, recover the associated coal as a saleable product. Where these solids are not wasted to streams or to slime ponds they are recovered by thickeners and filters. Since filter cake is often high in ash or sulfur, or both, it is not readily marketed or used. Common practice is to mix it with other plant products, generally slack or cleaned run-of-mine. Uniform blending is difficult, not only because the impurity is usually high, but also because during certain operating periods it is possible to get a concentration of this filter cake in a railroad or barge. At some plants filter cake has been derived from the froth flotation clean-up of Dorr thickener underflow. The operating circuits required for a froth flotation plant make this a comparatively high-cost treatment, and in the last few years experiments have been carried out with bulk oil methods. These also are quite expensive and lend themselves only to special situations. Table I gives some characteristics of thickener underflows for plants in the Pittsburgh area treating Pittsburgh seam coal. It will be noted that there is a concentration of impurities in the -200 mesh sizes.

Jan 1, 1960

By W. C. Winegard, C. J. Simpson

BNINGESSNER et al.1 have shown that the solidification substructure in dilute cadmium alloys persisted after repeated deformation, recrystallization, and annealing treatments. On the basis of this and similar evidence, Whelan has suggested in a recent publication&apos; that the solidification structure might affect the mobility of grain boundaries even after primary re-crystallization. This suggestion is important, since the technique used by previous investigators3-5 to fabricate grain growth specimens consisted only of casting, deforming, and recrystallizing prior to the grain growth anneal. Usually no attempt was made to homogenize samples with prolonged annealing. Experiments. To test the Whelan hypothesis, grain growth experiments were performed with samples in which the degree of solute segregation was altered by controlling the solidification rate of the alloys. The initial experiments were performed on the Pb-Ag system. Alloys containing 0.01 at. pct Ag were produced from 99.9999 pct Pb and 99.999 pct Ag. Cylindrical samples, 40 cm long and 12 mm in diam, were solidified in graphite-coated Vycor tubes by lowering them through a vertical furnace at varying rates with the furnace power settings constant. Six-centimeter sections were discarded from each end, and the 28-cm section from the center was cut into sections 25 mm long for grain growth experiments. These samples were deformed with the aid of a drophammer to a uniform thickness of 5.7 mm. After almost instantaneous recrystallization, the samples were given a grain growth anneal for various times at 260°C in a salt bath. Experimental results are shown

Jan 1, 1970

By Euclid P. Worden

In 1977, an article in World Mining1 reported a total of 2726 rotary blasthole drills in service. This figure included only those machines produced by three of the manufacturers building drills of this type. The total, therefore, is much higher. Rotary drilling in the mining industry is big business to the manufacturers and suppliers involved, and a significant cost item to mine operators. The time has come to take a hard look at rotary drilling technology with an eye to reducing costs by increasing drilling efficiency. The efficiency of any rotary drilling operation is best measured in terms of the rate of penetration achieved by the bit. In blast hole drilling, there are five factors which affect the rate of penetration. They are: (1) bit selection, (2) weight on the bit, (3) rotary speed, (4) hole cleaning, and (5) formation properties. Of these factors, all but one may be controlled by the operator. Looking at any one in detail may reveal possible improvements in the system. One of these factors -- proper hole cleaning - will be discussed in this paper. In order for a bit to perform at its maximum capability, each tooth or insert should strike fresh clean rock as it falls into its drilling position. If the tooth or insert lands on previously drilled cuttings, a major portion of the energy delivered to the bit is absorbed in redrilling this broken material. A major portion of the interest, therefore, should be directed to the proper cleaning of the bottom of the hole. In an in-depth study of the cleaning of large diameter holes, Allen2 reports that horizontal air velocities of 38.10 m/s are necessary to prevent the saltation of drilled cuttings on the bottom of the hole. The exact flow pattern on the bottom of the hole, however, is not generally known. The air leaves the bit through the jet nozzles and the mouths of the cones, but where it goes from there is uncertain. This problem should be investigated by the bit manufacturers because they can best utilize the results of such an investigation to provide a more effective product. Some work has been initiated in this area and competition will probably increase its intensity. Bailing velocity is the best criteria to measure the cleaning of the hole, including the bottom, and is the factor on which efforts toward improvement must be concentrated. The first consideration is "What should the bailing velocity really be?" In drilling deep holes for oil and gas, 15.24 m/s is the generally accepted figure. In blasthole drilling, the figures of 25.40 m/s for average rock to 35.56 m/s for iron ore were first mentioned by Capp3 in 1962. The recommendations are the same to this day. A number of questions could be asked in regard to the apparent disparity between these two sets of figures. Various investigators have derived formulas which support one or another of these criteria. A thesis on the subject was written by Alexander4 who derived a formula based on research which resulted in velocities in the lower end of the ranges quoted previously. He set out to compare this figure to laboratory tests and his tests indicated that the velocities given by the derived formula appeared to be high.1 Perhaps the best reason that the 25.40 to 35.56 m/s range has been used, is that these velocities seem to work. Below the accepted figures, low bit life and slow penetration rates occur. Above these figures, increasing amounts of abrasive wear on the drill pipe and stabilizers seem to appear. There is a fallacy to this entire approach, however. The entire velocity calculation is made using nominal bit and pipe sizes and compressor deliveries with no compensation made for losses in the system. Perhaps an examination of some of the things that are not presently considered could lead to some practical improvements in the operation.

Jan 1, 1980

By J. L. Walter

Extra-low carbon iron sheet, when deformed and annealed, undergoes exaggerated or abnormal grain growth in the critically deformed regions of the sheet. This exaggerated pmth occurs, for low strains (3 to 6 pct), only in sheet which has a fine dispersion of precipitates in the subsurface region of the sheet and fewer and coarser precipitates in the sheet interior. These particles have been identified as manganese sulfides. Wing the anneal, grains near the surface are gvowth-inhibited by the fine particles but the grains in the interior are free to grow normally. With the additional driving force provided by the strain energy, the interior grains first grow into the small subsurface pains. Eventually, these growing grains grow completely through the sheet. Calculations of limiting grain sizes at various values of strain indicate that a volume fraction of precipitates in excess of 10-&apos; would be required to eliminate exaggerated growth in material strained to 10 pct. OPEN-COIL annealing has made decarburization of sheet steel both efficient and economically practical. Use of such material for porcelain-enameling stock is one of many possible applications of low-carbon iron since carbon in steel is deleterious to porcelain-enameling properties.&apos; However, the extra-low carbon iron presently available presents another problem, that of exaggerated grain growth in regions where the sheet has been deformed as by bending or stretching. In exaggerated grain growth a few grains start to absorb their neighbors and these may become very much larger than the average grains of the sheet. Other names for exaggerated grain growth are coarsening, critical grain growth, secondary recrystallization, abnormal grain growth, or discontinuous grain growth. While this grain growth does not affect the enameling qualities of the low-carbon iron sheet, their presence results in a marked reduction of tensile-yield strength in the region of the sheet containing the large grains. The loss of tensile yield strength may render the material unsuitable for many applications . This report describes the results of a study undertaken to determine the cause of the exaggerated grab growth in extra-1ow carbon iron and, if possi- ble, to prescribe practical procedures for its prevention. GENERAL THEORY The driving force for exaggerated grain growth is the grain boundary free energy. This driving force is proportional to (l/rl + l/r2) where rl and r2 are the mutually perpendicular radii of curvature of the boundary between the growing grain and the grain being consumed. Thus, the greater the difference in size between the growing grain and the matrix grains, the higher the driving force for grain growth. If, however, the matrix grains are free to grow simultaneously, the driving force for exaggerated growth will be diminished. Stability toward growth of the matrix grains may be caused by a) a strong single orientation texture (texture inhibition),&apos; b) a dispersed second phase,3"5 c) the thickness effect,&apos; or d) intergranular segregation.7"9 As exaggerated growth occurs when growth of the matrix grains has been slowed by the stabilizing processes mentioned above, there must be an additional factor acting to promote growth of a few of the grains to the point where they are enough larger than the matrix grains that boundary energy driving forces are sufficient to cause continued growth. For instance, at the annealing temperature, growth-inhibiting inclusions may slowly dissolve and coalesce. Eventually, a grain boundary becomes unlocked and migration occurs at the expense of neighboring grains. Or, an additional driving force may be supplied to some of the grains if the material is strained. Then, since some grains will be strained less than others, the difference in strain energy between adjacent grains may be sufficient to overcome boundary locking and allow growth of the grains with lower strain energies. In the present study, therefore, such factors as the presence or absence of dispersed phases, the nature of the exaggerated growth, and the effect of strain have been considered. EXPERIMENTAL PROCEDURE I) Material and Processing. Three types of low-carbon iron were used in this study; types A and B were commercial grades, each from a different supplier.* The precise details of the processing of

Jan 1, 1963

By H. Margolin, A. Coucoulas

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKcll radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuAl2, and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band.1,4 Europium in EuAl2 appears to have a valence closer to 2. In previous work.&apos; X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref. 1. One of the other phases was identified as Co5Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. &apos;J. H. Wernick and S. Geller: AIME Trans., in press. &apos;J. H. Wernick and S. E. Haszko: to be published. &apos;F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. &apos;S. E. Haszko: to be published. &apos;J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acia Cryst., 1959, vol. 12, p. &apos;162. A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently hiher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1 week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By Appendix by A. S. Goldoni, R. E. Tate, E. M. Cramer

The diffision coefficient for self-diffision of plutonium in the temperature range 350" to 440°C has been measured by using puZ3 as the tracer isotope. Autoradiopaphic techniques were used to inzlestigate the possibility of grain boundary diffusion, hut only evidence for volume diffusion was found. The least-squares fit of the data gives the .following equation for the diffision coefficient: The computer least-squares technique for fitting the nonlinear equations is outlined. DETERMINATION of the self-diffusion coefficient of the fcc 6 phase of plutonium is in principle a straightforward experimental task. However, the chemical reactivity, the intense @ activity, and the toxicity of plutonium put limitations on the experimental techniques. The technique selected included roll bonding for preparation of the diffusion couples and pulse-height analysis of the @-particle activity to determine the distribution of the PU tracer in the diffusion couples. EXPERIMENTAL PROCEDURE Couple Preparation. Cylinders about 0.5 in. in diam were cast from two special stocks of plutonium, one of which had been enriched in puZ3&apos;, as shown in the isotopic analyses listed in Table I. For each roll-bonded composite sheet, a cylinder 0.437 in. in diam and 0.190 in. thick was turned from each kind of plutonium on a lathe in a 98 pct He atmosphere. The two freshly machined cylinders were positioned face to face in a tube of commercially pure aluminum which had been sealed at one end by welding and the assembly was evacuated on a vacuum manifold overnight. The elapsed time between machining the faces of the plutonium cylinders and evacuating the loaded tube was about 15 min. After overnight evacuation of the assembly the indicated vacuum was 1 X 10"5 torr or better. The aluminum tube was then warmed and pinched off with a cold-welding tool. The pinched-off weld was also fusion-welded as an additional precaution against leakage of air into the evacuated assembly. The assembly was immediately heated for 30 min in a 250°C furnace and reduced in thickness by being passed through a rolling mill with rolls heated to 200°C. The rolling schedule (four passes of 100 mils each with a 10-min reheat after two passes) reduced the thickness of the assembly to 100 mils. The rolled assembly was allowed to cool normally in air. The rolled assembly was sheared at the edges and the aluminum peeled from the composite plutonium sheet. The elliptical sheet was about 0.060 in. thick and usually three 0.383-in.-diam disks could be punched from its central portion. The sheet was heated on a hot plate to the ductile low 0 range (140°C as measured by temperature-indicating pellets) before each disk was quickly punched. The quality of the bond in the disks was evaluated by metallographic examination of the scrap sheet adjoining the hole left by the punch. Only well-bonded specimens without oxide in the interface (as indicated by metallography) were considered satisfactory for further use. More than half of the specimens so examined contained sufficient oxide in the interface to be rejected. Diffusion Anneal. Each disk to be diffusion-annealed was wrapped in 1-mil-thick tantalum foil and sealed within a Pyrex capsule evacuated to 1 x 10~5 torr or better. This capsule was then sealed within another Pyrex capsule at a similar pressure. The diffusion anneals were carried out at temperatures between 350" and 440°C in Marshall furnaces adjusted to have a temperature gradient of not more than *1/2"C over a 5-in. length. This gradient was then further smoothed by using a nickel tube as a liner in the furnace. The liner was divided into three longitudinal cavities by a septum of nickel sheet to which two calibrated Chromel-Alumel thermocouples were attached. One thermocouple was used for controlling the furnace temperature by means of a Brown Pyrovane controller equipped with a Capaciline anticipation circuit; the second thermocouple was monitored twice daily with a Leeds and Northrup K-2 precision potentiometer.

Jan 1, 1964

By ELTCENE A. WHITE

WE are all interested in our ou7n lines of endeavor and consider ourselves the center of the universe. The farmer thinks he is the most important man because he feeds us. The doctor knows he is the real center because he keeps us well. The lawyer says that he is indispensable because he keeps the peace. The banker furnishes us a place to keep our money and tells us how to make proper use of it. The miner sags that without metals there would be no civilization. I think that my branch has sufficient interest and exhilaration. of accomplishment to fully occupy any man&apos;s mind and attention. Mining and metallurgy are as old as the human race. It did not have much, if any, importance in the stone age as there are not found remains of iron and copper, but in the bronze age, which was co-existent with the stone age, it came to the front. Iron and copper were the most important metals. Copper, as bronze, was known in ancient Egypt, I\~:IS important in Rome and other parts of Europe and in Asia; in South America among the Aztecs and farther North were the Mound Builders and the early inhabitants of Lake Superior. At a very early date the Egyptians conquered the Sinai peninsula for the sake of the copper produced there. The history of copper metallurgy can be compared to that of a flower. The seed is sown in darkness and in the Dark Ages the crude metallurgy of copper began. As the shoot comes up from the seed it may be compared to the age of alchemy; the branches of the plant can be compared to the Middle Ages; the flowering shoots to the 17th century, the budding to the 19th and the blossom to our own time from 1870 on.

Jan 1, 1930

By Persifor Frazer

COMPARATIVE columns expressing the series of rocks of the lower half of the Mesozoic age in this country and in Europe are not yet definitely established. The following represents a co-ordination of the beds in England and Germany,* with a list of materials to be worked in from this country. † * Cotta, " Geologic der Gegenwart." † Section from York to Dillsburg. Report C, 1875; Second Geological Survey of Pennsylvania.

Jan 1, 1877

By S. A. Lever, R. Hultgren

The solidus is usually the least satisfactorily determined portion of a phase diagram. Cooling curves, which succeed well with the liquidus, show the solidus inaccurately or not at all because of segregation which occurs during freezing. Heating curves of carefully homogenized alloys might be expected to indicate accurately the solidus, but they are seldom used. Dynamic methods involving heating or cooling are never completely satisfactory because of uncertainty as to whether equilibrium is attained. A static method in which the specimen may be allowed hours, days, or even weeks to attain equilibrium is to be preferred. In a static method a solid solution, for example, is first made thoroughly homogeneous, then heated to successively higher temperatures. After sufficient time at each temperature to assure equilibrium, some property is measured which should alter strikingly when melting begins. Microscopic examination can be used to detect the beginning of melting, but the method is tedious since the specimen must be quenched, sectioned, polished, and etched before each examination. Of all the physical properties which change on melting, electrical resistance is probably the most satisfactory to measure. The measurement may be made while the specimen is at temperature without damage to the specimen. It may be repeated indefinitely to ascertain when equilibrium has been achieved. Measurements may be made on a single specimen over the whole range of temperature. Most metals approximately double their resistance on melting. Since an accuracy of a few tenths of a percent is easy to achieve, the method is highly sensitive to the beginning of melting. In spite of these advantages, which have been perceived for a long time,l,2 a reasonable search of the literature has failed to reveal a single case in which the method has been satisfactorily applied in practice to the determination of solidus temperatures. The use of electrical resistance measurements appears to have been confined in practice to changes in the solid state. In the work described in the following pages we have applied the electrical resistance method to the solidus of the lead-tin system. We have found the method to be convenient, reproducible, and highly sensitive. We chose the lead-tin system because it leads to few technical difficulties. Furthermore, a number of determinations of solidus have been made in this system by various methods and results could be checked against them. However, all published results are not in good agreement with one another, so this work should help in determining the solidus more precisely. The Lead-tin Diagram Because of its commercial importance, there have been numerous investigations of the lead-tin diagram. The results of the most recent work on the solidus are indicated in Fig 7, as well as the results of the present work. The works of Honda and Abe3 and of Stockdale4 agree fairly well with each other and with the present work. Jeffery&apos;s5 data indicate the solidus to be about 50°C lower. Honda and Abe3 used differential thermal analysis on both heating and cooling cycles. Stockdale4 used the microscopic method and also differential heating curves. Stockdale&apos;s results were about 4" higher than those of Honda and Abe at low tin contents and lower at higher tin contents. These results also agree with those of Rosen-hain and Tucker.= Jeffery5 used electrical resistance measurements of the alloy as it was being heated or cooled. Apparently he did not attain equilibrium as his results are about 40°C lower than those of Stockdale4 or Honda and Abe.3 MATERIALS AND METHODS The lead and tin used were of high purity. They were supplied by the American Smelting and Refining Co., who gave the following analyses: Lead: silver, 0.0016 oz per ton; copper, 0.0008 pct; cadmium, 0.0007 pct; zinc, 0.0002 pct; arsenic, 0.0003 pct; antimony, 0.0002 pct; bismuth, 0.0005 pct; tin, 0.0001 pct; iron, 0.0020 pct; lead (by difference), 99.995 pct. Tin: antimony, 0.037 pct; arsenic, 0.020 pct; bismuth, 0.004 pct; cadmium, trace; copper, 0.025 pct; iron, 0.004 pct; lead, 0.020 pct; nickel and cobalt, 0.005 pct; silver, 0.0005 pct; sulphur, 0.005 pct; tin (by .-difference). 99.88 pct. One hundred grams of metal with the desired proportions of lead and tin was weighed out to the nearest one-tenth of a milligram. The mixture was placed in a silica crucible, covered with charcoal, and melted in a reducing atmosphere in a gas-fired furnace. The alloy was well stirred. Chemical analysis of two of the alloys checked closely with the weighed portions. The compositions of the remainder of the alloys were taken directly from the weighings, without chemical analysis.

Jan 1, 1950

By P. E. Busby, C. Wells, M. E. Warga

Fundamental data on the rate of diffusion of boron in austenite and solubility of boron in the a and y phases of iron and steel have been obtained from deboronizing experiments and provide partial explanations for some of the phenomena observed in boron steels. The rate of diffusion of boron is about the same as carbon in austenite. The solubility of boron in austenite at normal heat-treating temperatures is less than 0.001 pct. A partial tentative Fe-B phase diagram in the important low boron concentration ranges and an equation representing the diffusion of boron in austenite are presented. A LTHOUGH a search of the literature revealed ALTHOUGHthat boron diffusion had not been studied quantitatively and systematically prior to 1948, a few qualitative observations which were made by following the diffusion of boron into iron packed in ferro-boron1-3 suggest that boron obeys normal diffusion laws and that the rate of diffusion increases with increasing temperature. The claim of Cornelius and Bollenrath1 that boron does not appear to influence the rate of carbon diffusion has recently been substantiated by Wells, Batz, and Mehl.4 Calculations based on data from the paper by Campbell and Fayv indicated that the diffusion coefficient (D) for boron in iron at 900°C is approximately 3x10 sq cm per sec; a value of 2x10-7 sq cm per sec at 1038°C has been reported by Digges et al in connection with decarburizing experiments on a commercial boron steel containing 0.43 pct C. During the period 1948 to 1950 several diffusivity constant (D) values for the diffusion of boron in the y phase of iron and steel and a number of solubility values for boron in both a and y phases were reported. It was concluded tentatively as a result of Metals Research Laboratory studies that D values for boron in y and a phases are about the same as for carbon in the comparable phasesa and that carbon up to 0.4 pct did not affect the rate of diffusion of boron in y iron above 1000°C within the limits of experimental error. Whether saturation of the y or a phases with carbon would significantly affect rates of diffusion of boron through them was then and still remains in doubt. The best estimate of Q (activation energy) was reported to be about 25,000 cal, somewhat lower than that for carbon in y iron. The solubility of boron in y iron at 1000°C was thought to be higher than 0.004 pct B but not as high as a more recent analysis of available data shows it to be. The solubility of boron in a iron at 700°C was reported to be 0.0004 pct B, but it would not have surprised the authors if the true solubility value is actually lower than this. Breaks in diffusion curves which were not understood when first obtained prior to 1950 have now been recognized as indicating solubility limits, and these are included in the present paper. Experimental Procedure Two methods were employed in an effort to determine diffusion coefficients (D) for boron in austenite. Early experiments involved the use of welded couples prepared in accordance with the procedure of Wells and Mehl,&apos; but when the results of these experiments proved to be unsatisfactory for calculating D values, studies were continued by means of deboronizing experiments. In both cases, boron analyses following the diffusion anneal were carried out spectrographically and all D values were computed using the Grube solution of Fick&apos;s law. The precision of the spectrographic method used proved to be about equal to that reported by Corliss and Scribner" —average deviation from the mean about 5 pct of the amount present when the boron content is 0.003 pct. Concentration-penetration curves obtained from spectrographic analyses of welded couples generally indicated that practically no boron was transported across the weld interface during the diffusion anneal. Furthermore the concentration-penetration

Jan 1, 1954

By H. R. Gardner

The heat treatmmt of plutonium was studied using the Jominy end-quenching technique commonly used for determining the hardenability of steel. Plutonium specimens were end-guenched from temperatures in each of the ß, y, d, d&apos;) and E phases. One series of specimens with a low-iron content, 165 pprn Fe, and another gvoup with a high-iron content, 678 pprn Fe, were used in order to study the effect of a Pu-Pu,Fe eutectic network on the hardness and micro-structure. Hardness traverses indicated no significant variations in hardness with either cooling rate or quench temperature. Metallographic studies indicated major effects on microstructure. Grain size was found to vary markedly with quenching temperature and cooling rate. It was determined that the Pu-PueFe eutectic network could be modified extensively by heat treatment, including spheroi -dization in the y phase and 6 phase below 413°C. An unidentified spheroidal inclusion was observed to go into solution in the delta and higher temperature phases. 1 HE element plutonium is unique among metals in that it has six allotropic forms in the solid state.&apos; These have been designated&apos; as the a, ß, y, d, d&apos;, and phases. The respective phase transformations occur at approximate temperatures of 122", 210°, 319°, 450°, and 480°C with a melting point at 640°C. With this number of phase transformations it becomes pertinent to consider the effect of heat treatment and cooling rate in the various phases on the microstructure and hardness of plutonium. To determine; the effect of a wide range of cooling rates, the Jominy end-quenching technique was applied to cylindrical plutonium specimens. In addition, since the presence of iron in amounts greater than 500 pprn is common in plutonium and results in a network of the Pu-Pu6Fe eutectic, it was decided to study heat treatment effects on two bomb reduced plutonium buttons with different iron contents. A low iron button containing 165 ppm Fe and a high iron button containing 678 ppm Fe were selected for this comparison. EXPERIMENTAL PROCEDURE Experimental Material. The cylindrical bars for Jominy quenching were cast from button stock in vacuo in MgO coated graphite molds. Metal pouring temperature was approximately 950°C and the molds were preheated to 300°C. The castings were machined to 0.5 in. diam. by 2.5 in. long cylinders. Chemical analysis and density data for the two groups of Jominy specimens containing different iron contents are presented in Table I. Except for iron, heats 19-12-1 and 20-2-1 are comparable within the limits of analytical accuracy. Representative specimens from the low-iron and high-iron bars were taken for metallographic examination. The low iron specimen was found to have extensive microcracking, Fig. 1. In addition, numerous unidentified spheroidal inclusions were present, Fig. 17. The average grain size of the low-iron plutonium is 0.068 mm, Fig. 4. In the high-iron plutonium, a Pu-Pu6Fe eutectic network is prominent, Fig. 7. The average size of the network is 0.100 mm. Unidentified spheroidal inclusions were also common in the high-iron plutonium. The average grain size of the high-iron plutonium is 0.036 mm. Experimental Technique. A Jominy end-quenching fixture was fabricated for glove box use. A 2.5 in. water height was used with an orifice of 0.250 in. ID. The orifice to specimen distance was maintained at 0.5 in. Annealing temperatures of 160°, 265°, 400°, 465°, and 535°c were chosen for the study of the effect of quenching from ß, y, d, d&apos;, and e phases on microstructure and hardness. During quenching, cooling curves were obtained from the Jominy specimens at distances from the quenched end of 1/16, 1/8, 3/8, 3/4, 1-1/4, and 2 in. Cooling rate calculations were made from the cooling curves for temperature intervals of 100° to 110° 160" to 170°, 330" to 340°, 420° to 430°, and 490° to 500°c. These temperature intervals were chosen

Jan 1, 1962

By U. K. Custred, E. W. Long, V. R. Degner

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. One approach towards increasing plant production capacity to meet the growing demand is through large-capacity flotation cells, provided they achieve metallurgical performance comparable to existing smaller cells. A 9-month evaluation test program recently completed at the Haynsworth mine at Bradley, Fla., demonstrated the feasibility of achieving economically acceptable concentrate grade and recovery levels using large, high-capacity flotation cells. The composition of the feed to the Haynsworth beneficiation plant is a typical Florida pebble phosphate matrix composed of phosphorite pebbles ranging in size from approximately 1-1/2 in. down to 150 mesh and intimately associated with a mixture of clay and sand (essentially silica). The feed contains approximately 22 to 28% phosphate reporting as tricalcium phosphate, Ca3 (PO,) 2, or "bone phosphate of lime" (BPL). The flotation section utilizes the double-float procedure typical of Florida plants. The phosphate is first floated away from the silica in the rougher circuit, using crude fatty acid, ammonia, and fuel oil or kerosene. Rougher conditioning is accomplished at 60 to 70% pulp solids with sufficient ammonia added to raise the pH to 9 to 9.5. Following coarse and fine rougher flotation, the concentrate (overflow) streams are joined and conditioned (sulfuric acid cleaned and washed) prior to entering the cleaner circuit where an amine float (cationic reagent and kerosene added in the feed box; pH 7.3 to 7.8) is employed to float the silica. The feed to the coarse rougher circuit averages 29% +35 mesh while the fine rougher feed averages 10%+35 mesh. Primary attention was directed toward the large rougher cell performance (recovery and grade) on coarse feed during the Haynsworth evaluation program. Flotation Cell Test Program A row of three No. 120 size (300 cu ft) WEMCO flotation cells was installed in parallel with an existing air-cell row. The total installed volume of the large cell circuit was 900 cu ft and required a floor space of 306 sq ft. This compared to the air-cell total volume of 200 cu ft and 152 sq ft floor space. (Both floor areas include feed and tails hoppers but exclude walkways.) Fig. 1 is a schematic cross section of the large flotation cell showing the relative location of key mechanism elements. In operation, the rotor generates a fluid vortex extending up along the walls of the standpipe and creating a sufficient vacuum within its core to ingest air into the standpipe/rotor cavity through the air inlet duct. The ingested air mixes with the pulp, which has been recirculated through the false bottom and draft tube, in the rotor. Further mixing occurs as the air and pulp move radially outward from the rotor, finally passing through the disperser into the flotation cell. Flotation is accomplished outside the disperser, where phosphorite laden air bubbles rise and the remaining pulp recirculates down along the cell wall to the false bottom and draft tube. Large-flotation-cell performance is influenced by the ability of the mechanism to (1) circulate, or suspend, the solids in the pulp; (2) ingest air into the rotor cavity; and (3) mix the air and pulp effectively. The proper balance between pulp circulation and air ingestion is a key consideration in achieving good recovery in a course feed application. Large-flotation-cell pulp circulation and air transfer characteristics are significantly influenced by rotor speed and rotor submergence; therefore, these two operational parameters can be used to "optimize" a particular mill application. Fig. 2 maps the hydraulic performance of the WEMCO No. 120 size flotation cell. This map can be used to relate the cell operational parameters which influence metallurgical performance. At a given rotor speed, power intensity (i.e., pulp circulation) is seen to increase, and airflow decrease, as rotor submergence is increased. The inverse relation between power and airflow is due to the two-phase air-liquid mixture density reduction accompanying the increased airflow rate. For any fixed rotor submergence, the power intensity (i.e., fluid circulation) and airflow both increase as rotor speed is increased. The selection of these two mutually related operating conditions (i.e., rotor speed and submergence) was a key consideration in the Haynsworth evaluation program.

Jan 1, 1976

By Tibor Stefansky, John E. Dorn

MOTT and Nabarro1-5 were first to illustrate the importance of the flexibility of dislocations in accounting for the strengthening that metals undergo due to the presence of internal-strain centers. Such strain-centers might arise from a number of causes such as radiation damage, the presence of semicoherent and coherent precipitates and clusters, as well as individually dispersed interstitial and misfit substitutional solute atoms. Each strain-center induces positive and negative shear stress fields on the slip planes of the surrounding alloy matrix. In order to effect plastic deformation, therefore, the alloy must be subjected to sufficiently high applied shear stresses to push dislocations past all such internal stress fields. If dislocations were inflexible and moved as rigid lines, they would be equally pushed and pulled by internal stress fields. At this extreme the strengthening would be vanishingly small. Dislocations, however, are not rigid; they are flexible and extensible. They wiggle between positive and negative strain-centers, thus increasing their line energy at the expense of their interaction energy with strain-centers. cottrel16 and Friedel7,8 have independently presented lucid reviews of the significance of the Mott-Nabarro dislocation-flexibility concept to the strain-center strengthening of alloys. Their analyses however were only semi-quantitative. There is evidence in the recent literature of renewed interest in a more rigorous analysis of flexibility. Thus, Gleiter9 and Gerald" have shown that the calculated strain-energy interaction between a dislocation and the stress fields of coherent precipitates can be seriously in error if the flexibility of the dislocation is not taken into account. This report will be concerned with a more detailed analysis of the problem based on the following approximations: 1) Although many types of strain-centers exist, the following analysis will be limited to the case of solute-atom strain-centers in fcc substitutional alloys. 2) To facilitate the analysis by avoiding statistical considerations, the strain-Centers are assumed to be in regular arrays on the slip plane. Although the quantitative results are somewhat dependent on the type of array that is assumed, the qualitative trends are similar for various arrays that were studied. 3) An adjustment of the results from those for square arrays to those for the more realistic case of a random distribution of strain-centers is accomplished by adopting the interesting statistical theory first introduced by Kochs,11,12 elaborated on by Dorn, Guyot, and stefansky,13 and analyzed by Foreman and Makin14 in their computerized experiments. 4) For simplicity the dislocation lines are taken to wiggle about their edge orientation and no correction is applied to their line energy for deviations from edge configurations or for the elastic interaction between segments of the now curved dislocation. It will be shown that for extremely low concentrations of atomic strain-centers the strengthening increases with the square root of their concentration. For slightly higher concentrations the strengthening rate becomes less rapid. At a critical concentration a maximum strength is obtained and a decrease in the strengthening takes place as the concentration of solute atoms is further increased. These trends are a direct consequence of dislocation flexibility. They arise from changes in the amplitude of the waviness of the dislocation line at the yield stress with solute atom concentration. Despite the simplifying assumptions that were made, the results agree qualitatively with appropriate experimental data. I) STRESS FIELDS ON SLIP PLANES Internal stresses are introduced in a lattice whenever a host atom of radius ro is replaced by another that has a different atomic radius. According to the classical theory of linear elasticity,15 the stress field about a solute atom at the origin of a spherical coordinate system is given by arr=-4G€(?_0)3 ffflfl ="W =2G€{t) f°rr^ro(l+e) UJ where G is the shear modulus of elasticity and Y, = ro(l + E) is the radius in situ, of the substituted atom. As shown by ~shelb~,&apos;~ this approximation assumes that the bulk modulus of elasticity of the substituted atom is identical with that of the host species. ~abarro&apos;~ suggested that the strain E can be deduced

Jan 1, 1970

By A. T. Corey, C. H. Rathjens

INTRODUCTION Although the oil industry has been aware of the directional variability of permeability in porous rock, the directional variability of relative permeability has been largely ignored. Yet it is apparent that such an effect must be present in a system in which the distribution of oil and gas within the porous matrix is controlled by capillary forces. It is easy to visualize a rock composed of layers of fine and coarse material such that gas flow across the bedding planes would take place only after the average oil saturation had been reduced to a very low value. The fine layers, because of their greater capillarity, would remain saturated and act as barriers to the flow of gas after the coarse layers had been desaturated. Flow of gas parallel to the bedding planes would obviously take place at a much greater liquid saturation. Without more complete information concerning the geology of a reservoir than is generally available, it is not possible to predict exactly how such phenomena would affect the over-all performance of an oil field. It is possible, however, to predict qualitatively the effect of stratification on relative permeability measurements made on laboratory cores. In this investigation the effect of stratification was studied analytically by assuming that two porous materials with different capillary pressure-desaturation curves (but identical relative permeability curves) were in contact and in capillary equilibrium. As a qualitative check on the analytical results, cores having various degrees of visible stratification were used for relative permeability measurements made with fluids flowing both parallel and perpendicular to the bedding planes. A quantitative check was considered impractical because of the difficulty of devising models in which two materials of predetermined properties could be joined without the plane of contact becoming a discontinuity. THEORETICAL CONSIDERATIONS AND ASSUMPTIONS The assumption of capillary equilibrium in an oil-gas system implies that the difference in pressure between oil and gas is everywhere the same. This means that the curvature of the interfaces must be everywhere the same in order to satisfy the equation where PC is the pressure difference between phases, y the interfacial tension and r, and r2 are the major and minor radii of curvature. Depending on the pore size distribution of coarse and fine layers, the volumetric percentages of oil and gas in these layers will differ when equilibrium exists. The exact relationship can only be determined by obtaining the complete capillary pressure-desaturation curves for each of the porous materials in contact. It has been pointed out elsewhere&apos; that the capillary pressure-desaturation curves of sedimentary porous materials can often be approximated by the relation where C is a constant and Soe is the effective saturation to oil based on a percentage of the pore volume effective to flow. In the same paper it was indicated that, as a first approximation, the values of oil relative permeability are given by and the values of gas relative permeability by For this analysis Eqs. 2, 3, and 4 were assumed to apply to each of two components of a hypothetical porous rock in capillary equilibrium. It was also assumed that each of the components had a residual wetting phase saturation of 20 per cent so that 80 per cent of the total pore volume was effective to flow. The permeability of the coarse stratum was taken as 100, and its displacement pressure was such that C in Eq. 2 had the numerical value of 1. The corresponding values for the fine stratum were 10 for the permeability and 10 for C. Units are not specified because they do not enter into the final results. The choice of the permeabilities and displacement pressure ratios was made to expedite the calculations. Any reasonable rock properties could have been chosen without changing the results qualitatively. Several arrangements of the two components were studied. Table 1 summarizes the resultant permeabilities obtained for four types of arrangement. RELATIVE PERMEABILITY CALCULATIONS The first step in the computation of relative permeability for the composite cores was the plotting of the capillary pressure-desaturation curves and the relative permeability curves for the individual components according to Eqs. 2, 3, and 4. At arbitrary

Jan 1, 1957

By Burdett Loomis

The advantages of gaseous fuel have been too fully set forth during the past few years to need recapitulation. Papers, arguments, and editorials have been issued, in a more or less general way, that would make volumes. Systems have found zealous advocates, and many promises of results that have sounded strangely in the ears of old-fashioned gas-makers, have been born of theory, and have died in the earliest throes of trial; while in some few instances success has demonstrated the value of practical effort. With few exceptions, however, everything attempted or accomplished has tended towards the one end-—the realization of more perfect results than we can

Jan 1, 1891