Search Documents

By C. A. Heberlein

C. A. HEBERLEIN,* New York, N. Y.-The results stated by Rey and Brevers are so startling that they are of great interest, as the concentration of a low percentage of cinnabar by differential flotation yields a high-grade concentrate in the presence of either arsenical or iron pyrite. The authors say: "Cyanide can thus be used to depress arsenopyrite and make a good cinnabar-arsenopyrite separation. A cinnabarpyrite separation could probably be effected in the same way." Corrosive sublimate at the present price of mercury would be a very expensive reagent but the expense would be justifiable if a high rate of concentration could be obtained with a high extraction. On my request, special tests were made in the Punitaqui mill in Chile along the line suggested by the authors, without any improvement of either grade or extraction. As the recovery of the cinnabar in a complex sulphide of chalcopyrite and pyrite gave unsatisfactory results, I had tests made at the testing laboratory of the American Cyanamid Co. at Stamford, Conn. As these tests turned out to be highly satisfactory, not only at Stamford but later at the mine, they are presented here. [AMERICAN CYANAMID TEST FEED PER CENT Si02 66.54 A12032.08 CaO0.70 MgO 0.00 Alkalis1.78 Fe15.63 Cu0.44 S9.42 Hg0.45 OZ. PER TON Ag0.95 Au0.151 Screen Analysis of Tailings, Per Cent Plus650.0 Plus 1001.32 Plus 15020.75 Plus 20019.85 Minus 20058.08] The pulp had a density of 22 and a pH of 7.8. Total time of conditioning was one minute. The reagent added was Texas fuel oil, 0.116lb. Of 33.7 Bé. gravity containing 0.9 per cent sulphur. Frother, 0.062 lb. of No. 5 pine oil. Rate of concentration of mercury was 25.7: 1 [ ]

Jan 1, 1941

The Mining Enforcement and Safety Administration has called attention to the increasing frequency of accidents occurring during mine maintenance and repair tasks in a recent publication. Data from the agency's Health and Safety Analysis Center have been compiled and presented in a report titled "Analysis of Injuries Associated with Maintenance and Repair in Metal and Nonmetal Mines,"* a booklet aimed at answering four questions: (1) Which pieces of operating equipment are most frequently involved in maintenance accidents; (2) Which maintenance functions are the most hazardous; (3) Which tools are most often associated with injuries; and (4) What is the comparative hazard of welding or flame cutting vs. mechanical or electrical maintenance functions.

Jan 3, 1978

By O. B. Hopkins

There was no noteworthy development in the oil industry in Peru during 1933 and all activities were restricted to the producing fields. The output of the country increased above that of previous years but there still remained a substantial shut-in production at the close of the year. The total production during 1933 is estimated at 13,259,891 bbl., of which the International Petroleum Co., Ltd. contributed 11,205,-362 bbl. A relatively small amount of new drilling was undertaken during the year. The International completed only one new well although a number of the old producers were reworked and deepened. Comments on Tables There are four oil districts in Peru, as shown in Table 1, although only three of these are now being operated. The exhausted Pirin field was abandoned eight years ago. La Brea-Parinus.—The La Brett-Parinas fields are on the property of the International Petruleum Co., Ltd. in the westernmost part of Peru. These fields include a number of producing districts that are defined by complex fault blocks associated with anticlinal folds. Data covering all the items listed in the table are not available on these fields but can perhaps be supplied in part in the future. Lobitos and Restin.—These two fields belong to the Lobitos Oilfields Limited and are near the coast, 10 to 20 miles north of the La Brea-Parinas fields. According to the Department of Mines and Petroleum of Peru, 311 wells at Lobitos and 197 at Restin had been drilled to the end of 1927. Since that date there has been enough drilling to increase moderately these figures. The depth of wells is not available but it is believed that their average depth is slightly greater than in the La Brea-Parinas area. The productive horizons are of Eocene age. zorritos.—The Zorritos field is the northernmost in Peru and is operated by the Establecimiento Industrial de Petroleo de Zorritos. The field is on the coast about 70 miles north of Lobitos. The number of wells drilled in this field to the end of 1927 was 343, according to the Department of Mines and Petroleum of Peru. The depths of these wells are reported to range from 300 to 700 ft. The largest wells do not produce

Jan 1, 1934

By P. N. Richards, M. K. Ormay

The present Paper extends the previous work on cold reduced, low carbon steels to preferred orientations developed after various heat treatments. In recrystal-lized rimmed steel, cube-on-comer orientations increased with cold reductions up to 80 pct. Above that {111}<112> and a partial fiber texture with (1,6,11) in the rolling direction dominated. During grain growth, cube-on-corner orientations have been observed to grow at the expense of {210}<00l>. In re-crystallized Si-Fe (111) (112) and cube-on-edge type orientations are dominant near the surface and the (1,6,11) texture near the midplane for reductions up to 60 pct. With larger reductions {111)}<112> and the (1,6,11) texture are dominant. In cross rolled capped steel a relationship of 30 deg rotation was observed between the (100)[011] of the rolling texture and the main orientations after re crystallization. Most orientations present in recrystallized specimens can be related to components of the rolling texture by one of the following rotations: a) 25 to 35 deg about a (110) b) 55 deg about a (110) C) 30 deg about a (Ill) THE orientation texture of recrystallized steel is of interest where the product is to be deep drawn, because preferred orientation is related to anisotropy of mechanical properties such as the plastic strain ratio (r value);1,2 and in electrical steel applications where a high concentration of [loo] directions in the plane of the sheet improves the magnetic properties of the material. It is interesting to note that both these aims are to a large extent achieved commercially, even though the orientation texture of cold rolled steel does not show large variation3 and the recrystallized orientations are generally given as being related to the as rolled orientations mostly by 25 to 35 deg rotations about common (110) directions.4-6 There is, as yet, no single completely accepted theory on recrystallization. The three mechanisms that have been investigated and discussed are: a) Oriented growth b) Oriented nucleation c) Oriented nucleation, selective growth Largely from the observations of the recrystalliza-tion process by means of the electron microscope,7-11 there is now considerable evidence that the "nucleus" of the recrystallized grain is produced by the coalescence of a few subgrains to form a larger composite subgrain, which finally grows by high angle boundary migration into the deformed matrix. From the intensive work on the recrystallization of rolled single crystals of iron, Fe-A1 and Fe-Si al-loys4-" he following observations have been made: 1) The change in orientation during primary recrys-tallization can usually be described as a rotation of 25 to 36 deg about one of the (110) directions. 2) The (110) axes of rotation often coincide with poles of active (110) slip planes. 3) If several orientations are present in the cold rolled structure, the (110) axis of rotation will preferably be a (110) direction that is common to two or more of the orientations. 4) With larger amounts of cold reduction (70 pct or more) departure from these observations became more frequent. 5) After larger cold reductions, rotations on re-crystallization about (111) and (100) directions have been observed. K. Detert12 infers that a rotation relationship of 55 deg about (110) directions is also possible, by stating that the recrystallized orientation {111}<112> can form from the orientation {100}<011> of cold reduced partial fiber texture A.3 The observation by Michalak and schoone13 that (lll)[l10] formed during recrys-tallization in fully killed steel containing (111)[112],— as well as (001)[ 110] which is related to the {111}<011> by a 55 deg rotation about <110>-implies a possible 30 deg rotation relationship about the common [Ill]. Heyer, McCabe, and Elias14 have recrystallized rimmed steel after various amounts of cold reduction, by a rapid and by a slow heating cycle and found that the preferred orientations strengthened with increased cold reduction. The most pronounced orientation up to about 70 pct cold reduction was found to be {1 11}< 110>, after 80 pct cold reduction both {111}<110> and {111}<112>, after 85 and 90 pct cold reduction, {111}<112>, and after 97.5 pct cold reduction it was {111}<112> and (100)(012). In the present work, the orientation textures of the recrystallized specimens are examined under various conditions of steel composition, amount and method of cold reduction, and method of recrystallization. The relationships between the preferred orientations of the as rolled and recrystallized specimens, and the conditions for the formation of the various orientations during recrystallization are investigated.

Jan 1, 1970

By J. W. Stewart

ONE of the postwar problems posed for mineral engineering educators is the desire of some mature student veterans to finish their college education under the G. I. Bill of Rights as quickly as possible, a desire that is quite understandable. Not only have they lost several years of education, which they wish to make up as quickly as possible, but many are married and have families and want to become productive as soon as possible in order to support their families properly. The obvious solution to this problem, if it really is serious, would appear to be a continuation of the wartime Accelerated Program, as it was carried on in most colleges and universities. As a matter of fact some schools are known to have continued their wartime programs in one or another form. To ascertain just what our mineral engineering schools generally are doing to meet this postwar problem, last April a questionnaire was sent to administrative officers at colleges and universities

Jan 1, 1946

R. H. THURSTON, Cornell University, Ithaca, N. Y. (communication to the Secretary): The " tri-axial diagram" was, I think, first employed by me in the work of the " U. 8. Board Appointed to Test Iron, Steel and Other Metals." A model was exhibited to the American Association for the Advancement of Science, and the diagram was first published, and the model described, in a paper presented to the same society at its Nashville meeting in 1877." The problem then presented to its inventor was to find a method of planning a research involving proportions of ternary compositions in such manner that, a limited number of such compositions being tested, the results should give the law of variation in the physical properties of all possible combinations of the three elements, and the actual numerical values of such as were important to the investigator. The investigation of the binary alloys, copper and tin, copper and zinc, and tin and zinc, had been completed and satisfactorily discussed, employing the usual bi-axial diagram, of which the ordinates represented the one, and the abscissæ the other, of the characteristic properties to be studied, the composition being commonly indicated by the abscissæ. In these cases it was easy to ascertain, by the study of a limited number of compounds, the law of variation in strength, ductility, etc., with composition; but, for a long time, the ternary alloys were not attacked, because no simple and satisfactory method presented itself of securing results significant for the whole field by the investigation of a comparatively small number of alloys. The tri-axial diagram was finally hit upon as a means of representing and interpreting results, and researches were at once begun, and in due time satisfactorily completed.

Jan 1, 1899

By R. H. Gautschi, F. C. Langenberg

Rare-earth additions were made to laboratory heats of Type 310 stainless to observe their effect on as-cast ingot structure, nitrogen and sulfur contents, and nonmetallic inclusions. Lanthanum had a grain-refining effect in 30-lb ingots, but results with 200-lb ingots were inconsistent. Cerium, lanthanum, and misch metal lowered the sulfur content when the sulfur exceeded 0.015 pct and the rare-earth addition was greater than 0.1 pct. The rare-eardh content in the metal dropped very rapidly within the first few minutes after the addition. The size, shape, and distribution of nonmetallic inclusions was not changed in 30-lb ingots, but changes were noticed in larger ingots. RARE-earth* additions have been made to austenitic Cr-Ni and Cr-Mn steels to improve their hot workability. The high alloy content of these steels often results in a considerable resistance to deformation and inherent hot shortness at rolling temperatures, particularly in larger ingots. Rare earths in the metallic, oxide, or halide form are usually added to the steel in the ladle after deoxidation although they can be added in the furnace prior to tap or in the molds during teeming. The literature- indicates that the effects of rare-earth treatments on these stainless steels are not consistent, and sometimes even contradictory. Since no mechanism has been presented which satisfactorily accounts for the claimed improvements, the effects of rare earths are a qualitative matter. The work described in this paper was initiated to expand the knowledge of the effects of rare-earth additions on melting variables such as ingot structure, chemical analysis, and nonmetallic inclusions. REVIEW OF LITERATURE Ingot Structure—Rare-earth additions to stainless steels have been reported to cause a change in primary ingot structure in that there are fewer coarse columnar grains. However, the results are inconsistent. While one investigation1 has shown a large reduction in coarse columnar crystals, another2 has been unable to observe this effect, particularly when small ingots were poured. Post and coworkers3 observed ingot structures for a number of years and found that the columnar type of structure is not definitely a cause of any particular trouble in rolling or hammering, provided the alloy is ductile. Knapp and Bolkcom4 found rare-earth additions to be quite effective in preventing grain coarsening in Type 310 stainless steel. Chemical Analysis—Many effects of rare-earth treatment on chemical analysis have been claimed in the literature. Russell5 observed that some sulfur is removed by rare-earth metals, and that a high initial sulfur content improved the efficiency of sulfur removal. Lillieqvist and Mickelson6 report that rare-earth treatment causes sulfur removal in basic open-hearth furnaces, but not in basic lined induction furnaces. Knapp and Bolkcom found no sulfur removal in acid open-hearth and acid electric furnaces, probably because the acid slag can not retain sul-fides. snellmann7 showed that sulfur could be lowered apprecfably with rare-earth additions; however, a sulfur reversion occurred with time. Langenberg and chipman8 studied the reaction CeS(s) = Ce(in Fe) + S(in Fe), and found the solubilit product [%Ce] [%S] equal to (1.5 + 0.5) X 10-3&apos;at 1600°C. Results in 17 Cr-9 Ni stainless were about the same as those in iron. Beaver2 treated chromium-nickel steels with 0.3 pct misch metal and observed some reduction in the oxygen content. He also noted an inconsistent but beneficial effect of rare earths when tramp elements were present in amounts sufficient to cause difficulty in hot working. It is not known whether rare earths reduce the content of the tramp elements or change the form in which these elements appear in the final structure. No quantitative data are available concerning a possible effect of rare-earth treatment on hydrogen and nitrogen contents. However, Schwartzbart and sheehan9 stated that additions of rare earths had no effect on impact properties when the nitrogen content was low (0.006 pct), but served to counteract the adverse effects of high nitrogen content (0.030 pct) on these properties. Knapp and Bolkcom4 analyzed open-hearth heats in the treated and untreated conditions and found the nitrogen content (0.006 pct) to be unaffected. These two results lead to the speculation that rare-earth additions can reduce the nitrogen content to a certain level. Decker and coworkers10 have observed that small amounts of boron or zirconium, picked up from magnesia or zirconia crucibles, increased high-tem-

Jan 1, 1961

By R. A. Wolfe, H. W. Paxton

Self-diffilsion coefficients for cr51 and Fe55 in 12 pct Cr-Fe and 17 pct Cr-Fe for Fe55 in chromium, and for Cr51 in vanadium have been measured. The results are compared with other values for the Fe-Cr system, and with the various theories of diffusion in hcc metals. Some empirical correlations are discussed between Do and Q in hcc systems, or, expressed differently, the constancy of ?G*/T solidus for seveval bcc metals and alloys is noted. It appears very probable that a vacancy mechanism is operative in bcc metals, hut this cannot he stated with certainty. THE great bulk of work on diffusion in metals, both experimental and theoretical, was for many years concentrated on those with close-packed and, in particular, fcc lattices.1,2 There appears to be little doubt that the mechanism of diffusion in these solids is vacancy migration, leading to mass transfer and in substitutional solid solutions to a Kirken-dall effect.3,4 For bcc metals, the picture is much less clear. The Kirkendall effect certainly occurs in several alloys.5-10 However, attempts to understand the factors contributing to the pre-exponential in the usual expression for the diffusion coefficient D =D, exp {-Q/RT) by extension of ideas useful in close-packed lattices have not always been successful. Zener,11 Leclaire,12 and Pound, Paxton, and Bitlerl3 have suggested that various forms of ring diffusion may be important in some bcc metals. For close-packed metals, Do is usually about 1 sq cm per sec and Q - 35Tm kcal per mole (Tm = melting temperature in OK). The theory of Pound et al. suggests for ring diffusion that Do may be about 10-4 and Q, although difficult to calculate with any precision, would be significantly less than 35 T,. The experimental results on self and solute diffusion in ? uranium14,15 and ß zirconium,10 and for solutes in 0 titanium,17 and possibly for self-diffu- sion in chromium below about 0.75 T,," gave some credence to this theory. However, not all bcc materials display low values of DO and Q, and the exceptions were not predicted by any theory. Furthermore, it has recently become apparent that, in bcc materials, log D is not always linear with T-l if a sufficiently wide range of temperature is studied.16,18 This variation may be such that Q may increase18,19 or decrease20 with increasing temperature. The present work was undertaken in an attempt to provide further diffusion data on bcc metals, and to try to understand the factors which contribute to differences in behavior between the various elements. For part of this work, the Fe-Cr system was chosen since it is of considerable technological importance, and data on 12 pct Cr and 17 pct Cr alloys appeared well worthwhile to supplement that existing for the remainder of the stern.18,22 The diffusion of Fe55 in chromium was studied as an example of a more or less "normal" tracer element in a possibly abnormal host lattice. Finally, no data were available for vanadium, the neighbor of chromium in the periodic table, because of lack of a suitable isotope so cr55 was used as a tracer in a few preliminary experiments. For convenience, we shall refer to elements whose Do and Q are low compared to those predicted by Zener&apos;s theory as "anomalous". PROCEDURE This investigation determined self-diffusion rates by means of radioactive tracers and the integral-activity method first utilized by Gruzin.23 In this method a thin layer of radioisotope of the diffusing element is plated or coated onto a planar surface of the diffusion sample, which is then given an isothermal-diffusion annealing treatment. The determination of an activity-penetration curve involves measuring the residual activity of the specimen after each successive layer or section has been removed parallel to the original planar surface. The method used here is essentially the same as that used by Gondolf18 and Kunitake.21 Two radioactive tracers, cr51 and Fe55, were used in this investigation. Diffusion coefficients were determined for the diffusion of one or both of these tracers in four different materials, viz., Fe-12 wt pct Cr alloy, Fe-17 wt pct Cr alloy, chromium, and vanadium. The diffusion samples had nominal dimensions of 1.5 cm diameter and 0.5 cm thickness. The grain size was several millimeters for the Fe-Cr alloys and at least 1 mm for the chromium and vanadium samples. Accurately planar surfaces

Jan 1, 1964

By P. Barnes

If it be admitted that the use of the metric system of measurement is desirable, and that it will be well, as urged by one of our engineering societies, to show upon all our plans or drawings a metric scale in addition to a scale of inches, then it becomes important to introduce some ready means of drawing these scales. For many present purposes it is quite sufficient to space off and to draw them with the common dividers and the right-line pen, but if the number of drawings made or copied in an engineer&apos;s office, and upon which scales must be shown, is more than two or three daily, then some more mechanical or automatic means should be provided. For a great majority of detail drawings, a simple transcript of the surface of a good two-foot rule would answer every purpose, and probably the best comparative showing of the metric scale would be made by drawing a line of millimeters close by the side of the line of sixteenths. This would be in fact little more than the

By J. R. Elenbaas, J. A. Vary, D. L. Katz

The development of gas fields, oil fields and aquifers for storing natural gas is treated from two main vieu.-points: (I) the volumetric storage capacity for gas in a given situation and (2) the prediction of the number of wells required for the delivery of gas. Other experiences in the design and operation of storagc fields are incluclerl INTRODUC TION Storage of natural gas in underground reservoirs near the terminus of long distance pipelines has been the prime factor in opening the space heating market to the natural gas industry. Storagc has permitted a major. increase in both the load and the load factor of pipe-lines; some are now operating at steady load throughout the year. Thus, underground storage has been responsible for the rapid increase in demand for natural gas in recent years. Three types of reservoirs have been used for gas storage: natural gas reservoirs, oil reservoirs, and waterbearing sands or aquifers. This paper presents the factors to be considered when developing gas storage reservoirs of these three categories. There are two prime considerations tor any storage reservoir: (1) the volume of gas which a given reservoir will store advantageously and (2) the number 01 wells needed to provide the required peak deliverability. These two problems will be considered for the three types of reservoirs just noted STORAGE IN PARTIALLY DEPLETED GAS FIELDS Early storage operations consisted of replenishing the natural gas in a depleted gas field situated adjacent to the market. Today, newly discovered fields near the market may be considered for storage, and this discussion applies equally to both types of reservoirs. For reservoirs originally containing gas or oil, the question of the impermeability of the cap rock nor-mally does not arise. However, such fields are likely to have many wells drilled either to or through the reservoir under consideration. Positive assurance must be obtained that such wells are or can be made mechanically tight. Corroded casings may need to be lined or permanently plugged. Abandoned wells should bc reopened and properly cemented. The volumetric capacity for gas storage depends upon space available in the porous rock as well as pressure and temperature of the gas in the reservoir. The production-pressure decline data on partially depleted gas reservoirs without water drive permit calculation of the reservoir space for gas. Isopachous maps of sand volume and porosity data for the reservoir rock provide an alternate method of calculating the pore volume for water-drive reservoirs. The pressure range selected for the storage cycle depends upon ()) the safe upper limit of pressure. 2) the flow capacity of wells and (3) compression requirements when injecting gas into the reservoir or delivering to market. Normally, gas and oil fields have pressures at discovery in the range of 0.43 to 0.52 psi/ft of depth. Pressures of around 1.0 to 1.2 psi/ft of depth appear to lift the overburden1-3 and invite uncontrolled movement of fluids in the porous rock. Some top pressure is normally selected for a storage reservoir ranging from below discovery pressure for deeper reservoirs to 0.65 psi/ft of depth for shallower reservoirs. Pressures to 0.66 psi/ft have been experienced without difficulty. The lower pressure limit is set by water intrusion accompanying low pressures, reduced flow capacity for wells at lower pressures and compression requirements. Depletion-type gas reservoirs often encounter water problems in the later stages of gas production. Such water intrusion may be due to movement from the surrounding aquifer. Accordingly, displacement of this water back into the aquifer by gas pressure and subsequent surges of water corresponding to the gas storage pressure cycle must be considered. Storage fields often produce in four months a volume of gas equal to its initial content. Rapid decreases in reservoir pressure occur, such as 20 psi/day. Accordingly, closed-in pressure observation wells which reflect the pressure in the bulk of the reservoir are required for following the operation of the reservoir. It has been found that a plot of observation wellhead pressures against gas content, Fig. 1, is very useful in observing operation of the field, checking the inventory and predicting future behavior. The plot is based on a given quantity of base or cushion gas in place. The injection and withdrawal curves may spread depending upon the homogeneity of the reservoir rock. permeability of the rock, well spacing and flow rates.

By Ivor Jenkins

Processes employing &apos;controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,&apos; but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

By Ivor Jenkins

Processes employing &apos;controlled at-mospheres in the heat-treatment of metals and alloys are now well established on an industrial scale, and the general principles involved and the advantages to be gained in the use of the technique have received considerable publicity over a period of years. During this time the greatest emphasis has been on the establishment of the process in industry, the main effort being devoted to development work on various types of atmospheres, their useful fields of application and the design of suitable heat-treatment furnaces in which they are to be used. The various types of controlled atmospheres are fairly well standardized, but there still remains a considerable field for the investigation of related problems, in connection with both the gas-generating equipment and the surface chemistry of the heat-treatment of metals, especially in complex controlled atmospheres. This paper describes certain investigations of this nature that were carried out in England up to 1939. The development of processes employing controlled atmospheres has been asso-ciated to a very large extent with the heat-treatment of steels, both because of the major importance of steel in industry and the many diverse and dificult prob-lems of surface chemistry involved when steels of such a wide range of composition are heated in the presence of active gases. Controlled atmospheres such as disso-ciated and burnt ammonia or charcoal gas are used in the heat-treatment of low-carbon and high-carbon steels, but from certain points of view a suitable atmosphere generated by the partial combustion of city gas is to be preferred. Both the ammonia derivatives are comparatively expensive, and even if the burnt ammonia is regenerated, thereby reducing operating costs, the capital expenditure of the gas plant may make it prohibitive for the smaller type of furnace installation. Charcoal-gas generators are not without their operating difficulties especially those associated with the quality of the charcoal, clinker formation and the removal of carbon dust from the generated gas. City gas has the advantage of being comparatively cheap and "on tap" in most if not all industrial centers. The use of raw city gas as a protective atmosphere in the heat-treatment of steels has been described,&apos; but it presents certain difficulties because of its complex composition and its explosive nature when mixed with air. These factors, together with the tendency toward sooting at elevated temperatures, arising mainly from the hydrocarbon gases present, all militate against its use as a protective atmosphere in industrial furnaces. The following analysis, based on the analyses of city gas in different localities in Great Britain, indicates the wide limits existing

Jan 1, 1948

Discussion of the paper of PHILIP W. HENRY, presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 1915, pp. 23 to 30. C. ,E. GRUNSKY, JR., San Francisco, Cal. (communication to the Secret ary*).-The difference of opinion of engineers on the subject of depreciation is justified, to some, extent, by the many viewpoints from which such a subject can be considered when applied to properties of widely differing physical characteristics. Mr. Henry takes up the subject of depreciation as applied alone to oil properties, and in doing so makes a clear distinction between amortization and the repair or renewal requirement. After carefully reading the paper the purpose of its author in suggesting a "depreciation" reserve or fund to keep the property at a constant value does not seem clear. As shown by Mr. Henry, the depreciation element as compared with the operating expense per gallon of oil is very large because of the comparatively short life of the oil properties, and it is also evident that such a "depreciation" fund would in a short time contain a very large amount of money. It seems desirable and permissible in income-tax matters to take into account the depreciation of property and to separate from the income such money as is necessary to amortize the invested capital to an extent warranted by the depreciation. However, it does not seem either necessary or desirable to create a large fund which will in time approximate the entire invested capital and which may he invested by the directors, as Mr. Henry suggests, "in the property itself or in outside securities." This method seems cumberome and liable to offer in the reinvestment of such a fund temptations to a directorate that might show more devotion to its own interests than that of the stockholders. A reserve fund is very frequently desirable in mining and oil operations, but to keep up a fund of this magnitude or to reinvest it in outside securities does not seem desirable from a stockholders&apos; standpoint. The. money withdrawn from the receipts to be placed in the depreciation fund (not including replacements and the drilling of new wells necessary to keep up the productiveness) should he returned to the stockholders of the company, not as dividends, but as an amortization of the invested capital.

Jan 5, 1915

By H. M. Ziesemer, George Mieyr

Prior to 1909 that mountain of porphyry known as Sacramento Hill had hardly been touched though it had always been thought to contain ore. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined ; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. NO ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300 ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a siliceous gangue. About 30 per cent. of the copper is caused by

Jan 1, 1923

By George Mieyr, H. M. Ziesemer

Prior to 1909 that mountain of porphyry known as Sacramento Hill had hardly been touched though it had always been thought to contain ore. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined ; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. NO ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300 ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a siliceous gangue. About 30 per cent. of the copper is caused by

Jan 1, 1923

By Edwin Shorey

IN THE southwestern Wisconsin zinc district, lying in Lafayette, Grant, and Iowa Counties, and the adjoining territory in northwestern Illinois, the orebodies are generally small, and are mined out in a few years. Many of the mines are developed with an expectation of five years or less of actual production. For this reason, as well as for considerations of economy, certain features in the development practice, which have been worked out with a view toward keeping the ratio of time required for, development to that occupied by actual production as small as possible, are of interest. ORGANIZATION The organization of a crew for, this work is as follows: Inasmuch as speed in sinking is desirable, the shaft crew comprises three shifts working 8 hr. each. In the smaller shafts, running up to 6 by 12 ft. (1.8 by 3.6 in.) in size, two men are employed on a shift; in larger shafts an additional man is usually employed. A mine foreman, or ground boss, has general control of the work of the three shifts. He is usually with the crew on the first and the early part of the second shifts, and plans the work to be done for the third shift when it comes on. His schedule, of course, is flexible and when pump changes, or other special conditions warrant, he, arranges his working time to suit the occasion. The surface crew for a sinking operation is made up of two hoistermen, each working 12-hr. shifts. Since the various operations in the shaft must be conducted in succession,. and not in combination, one with the other, separate attendance for hoisting and general plant is unnecessary. Drilling is done when no hoisting is necessary and vice versa. The hoisterman trams out and dumps the excavated material which the crew in the shaft is mucking, as a part of his regular hoisting work.

Jan 8, 1920

Jan 1, 1910

By Francis A. Thomson

But little has been written concerning the camp of Republic. In 1900 Chatard and Whitehead 1 reported the results of some experiments with samples of ore from the Republic mine, and a few years later Fritz Cirkel2 described the construction, operation, and results attained in the mill at the Mountain Lion mine. From time to time brief articles, mostly of a semi-technical nature, have appeared in the Engineering and Mining Journal and other mining periodicals. The general geology of the camp, especially in regard.to its areal features, has recently been ably described by Joseph B. Umpleby.3 To bring to mind the general features of the district it may perhaps be well to review briefly some facts in regard to it, before discussing the treatment of the ore. I. History and Production. The town of Republic is situated in the NW. corner of Ferry county, about 25 miles south of the International Boundary, on the head-waters of the San Poi1 river, in what was formerly the " north-half" of the Colville Indian reservation. On Washington&apos;s birthday, 1896, this portion of the reservation was thrown open to mineral location, and within a few weeks important discoveries had been made. The present Eureka mining-district was organized, the camp grew apace, and consignments of ore were shipped by wagon to Grand Forks, 30 miles away; or to Marcus, a somewhat greater distance. It is reported that the first 1,500 tons shipped from the Republic mine uetted the owners $160 per ton, after being hauled

Jan 1, 1913

E L. DEGOLYER, our new president, though a petroleum geologist by profession, has always s been associated with mining, for soon after his birth at Greensburg, Kan., on Oct. 9, 1886, his parents moved to Joplin, and when he went, in the course of time, to the University of Oklahoma, he intended to follow his course there with another at a mining school. He became a field assistant in the U. S. Geo-logical Survey, however, while still an undergradu-ate, and after field experi- ence in Montana, Wyoming, North Dakota, Colorado and Oklahoma, he went to Mexico as geologist for the Mexican Eagle Oil Co. This was in 1909, and as a result he was unable to complete his work for his degree until 1911. In Mexico, he located the Potrero de Llaño No. 4, one of the world&apos;s largest oil wells, and also the dis- covery well in the Naran- jos pool; and the Colorado School of Mines conferred the honorary degree of : Doctor of Science on him in 1925. On his return from Mexico, he engaged in the consulting business, specializing in financial ap- praisement, the Union and Marland companies being among his clients. In 1919, he organized the Amerada Petroleum Co., with the backing of Lord Cowdray. Last year, control of the company was purchased by an American group, headed by Dillon, Read and Co. Mr. DeGolyer is n o w president of the company. He is also vice-president and general manager of the Rycade Corp, the Rycade Oil Corp., and president of the Geophysical Re-search search Corp. The l a t t e r represents the practical appli-cation of his inter-est in the use of the torsion balance in the locating of salt domes, in which he has pioneered, the Nash dome being the first oil field in America actually brought into production by these methods.

Jan 3, 1927

By R. S. Shoemaker, R. M. Darrah

Expanded markets for copper in the past few years and a consequent search for new ore bodies have revitalized the widely known but seldom applied method of producing copper called heap leaching. Heap leaching is defined here as the process applied to oxide ores which have been mined solely for the purpose of leaching. In this case, all costs of mining the ore become a part (and a substantial one, as will be shown) of the cost of the copper produced, whereas in dump leaching the mining cost has already been accounted for as a stripping cost for the sulfide ore. Of course, with newly opened ore bodies, stripping costs may be divided through accounting procedures, between the copper produced by the mill and that obtained by leaching, but in general this type of operation must be economic on the basis of the sulfide ore alone. Heap Leaching Requires Low Capitalization Heap leaching, as a beneficiation method, is unique in that it is the only process used for the recovery of a metal in which the time involved from mining the ore to metal production is measured in months instead of hours or at the most, days. Then too, after the ore body has been depleted and mining has ceased, metal production will continue for some substantial period of time. Heap leaching is also unique because unlike any other method of beneficiation, metal recovery cannot be accurately forecast ahead of time and recovery will never approach that of a conventionally milled sulfide ore or even that of a vat leached oxide ore. Counter-balancing this drawback, however, is the relatively low capital expenditure necessary to put a heap leaching operation into production and the consequence that smaller ore bodies which would not support the higher capital cost involved in a vat leaching plant can be made into producers. Stated more simply, in heap leaching the operator accepts low recovery in exchange for low capital costs and low break even point. Whether the operator chooses vat leaching with its higher recovery and higher capital costs, is a mater of economics which depends in part on the nature of the ore to decide. For instance, an ore that will vat leach in 7 to 10 days using 7 pounds of sulfuric acid per pound of copper produced might use double or triple that amount of acid during the months that are required for heap leaching.

Jan 12, 1968