Search Documents

By James Norman

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content, it might be a desirable constituent of glass batches. The use of spodu-mene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manga-nese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li2O on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, ? the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3 The methods described in the second publication' did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted.

Jan 1, 1940

NEW MEMBERS The following list comprises the names of those persons who became members during the period May 10 to June 10, 1914. Members ABE, ASAKA, Chief Min. Engr., Yamagano Gold Mine, Satsuma-Gori, Satsuma, Japan. ANDERSON, FRANK M., Geol Cartagena Refining Co., Cartagena, Colombia, S. A. BACON, MAURICE W., Genl. Mgr Stewart Mining Co. Butte, Mont. BACON, RAYMOND F., Chem Director, Mellon Institute, Pittsburg, Pa. BAKER, HAMILTON WALLACE, Min. Engr Fernley, Nev. VON BAYER, AUGUST HECTOR, Supt Kentucky Solvay, Coke Co., Ashland, Ky. BISHOP, WHEELER SCOTT, Research Chem Care Braden Copper Co., Rancagua, Chile, S. A. BOWEN, CHARLES GILMAN, Timekeeper 208 School St., Grass Valley, Cal. BOYER, SAMUEL L., Mine Operator, Mgr., Mike. Horse Min. Co., W. 2808 Boone Ave., Spokane. Wash.

Jan 7, 1914

By W. W. Coffeen, K. E. Doud

A singular mineral extraction and processing operation is conducted by Metal & Thermit Corp. in Hanover County, Va. The mine presently produces aplite rock, rutile and ilmenite. The deposit lies in the piedmont plain about 25 miles northwest of Richmond. It first drew attention as a result of discovery of float rutile on the surface about 1910. About seven years prior to this, Metal & Thermit through a subsidiary. American Rutile Co., had begun producing rutile'and ilmenite from a deposit in Nebon County, near Piney River, where aplite rock and ilmenite are mined today. Because of the interest in titanium minerals and the similarity of the new deposit to the Nelson County deposit, Metal & Thermit became interested and eventually acquired the Hanover County deposit.

Jan 10, 1962

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10 to Nov. 10, 1914: Members ADDAMS, CHARLES EDWARD, Asst. Supt.. . Ray Consolidated Copper Co., Ray, Ariz. ALEXANDER, HARRY H., Asst. Mgr. and Mgr., American Smelting & Refining Co., Maurer, N. J. ALLING, MARK,N., Min Engr Downieville, Sierra Co., Cal. ANDERSON, LESLIE DOUGLASS, Supt U. S. Smelting Co., Midvale, Utah. ATKINS, WILLIAM, JR., Sec'y Kingwood Coal Co., Howesville, W. Va. BLAKE, TRUE WALTER, Min. Engr Rombauer Coal Co., Novinger, Mo. BRACKETT, GEORGE SYLVESTER, Supt... Pittsvein Coal Co., Flemington, W. Va. BRAINERD, HOWARD STANFORD, Met Ingersoll-Rand Co., Phillipsburg, N. J. BROWN, THOMAS J., Genl. Supt., Nova Scotia Steel & Coal Co., Sydney Mines, N. S., Canada.

Jan 12, 1914

By J. J. Gilman

Rates of prisnzatic plastic glide ( {1010}<2110>) in pure Cd crystals have been measured at temperatures from 158° to 276°C. The glide rate is proportional to the 2.75 power of the applied shear-stress. The activation energy is 29.2 kcal per mol. It is suggested that the rates of prismatic glide in Cd and Zn crystals are determined by the strengths of the atomic bonds across the prism planes. ALTHOUGH zinc and cadmium crystals both have hexagonal structures with nearly the same c/o ratios, their mechanical behaviors are quite different. Whereas zinc becomes quite brittle below room temperature, and cleaves readily on (0001) planes, cadmium is very ductile even at 4.2°K, and cannot be cleaved at any temperature. As part of a search for the explanation of this difference in behavior, a study has been made of prismatic glide in cadmium. It complements a previous study of the same phenomenon in zinc.1 The primary glide plane in cadmium is the basal (0001) plane, and the primary glide direction is the direction of atomic close-packing <2110>. However, if a tensile stress is applied parallel to the basal plane, then the shear stress on the basal plane equals zero so basal glide cannot occur. At low temperatures, deformation by twinning occurs; but at high temperatures, it has been found in this study that gliding on prismatic planes (1010) occurs in the close-packed direction. This is completely analogous with the case of zinc, except that lower temperatures are required. EXPERIMENTAL The experiments were done in nearly the same way as for zinc.&apos; Therefore, only the differences in the two sets of experiments will be described here; for other details the reader is referred to the previous paper. Crystals 6 by 6 mm sq were used that were grown from "Super Purity" 99.999 + pct Cd purchased from the New Jersey Zinc Co. The crystals were grown with their basal planes parallel to both the rod axis and one of the flat sides of the square cross section, A close-packed direction in the basal plane was oriented parallel to the rod axis. Gage sections were carefully machined into the crystals, and the surface damage caused by machining was removed with the same chemical polishing reagent as had been used for zinc. Thus, specimens of the same form and size as the previous zinc ones were produced. The crystals were heated to the test temperatures in a silicone oil bath (fused salts were tried first, but they reacted badly with the cadmium). An Instron tensile-testing machine was used for applying stresses to the crystals at various constant strain-rates. RESULTS The general behavior of cadmium crystals is much the same as for zinc. Only the constants that measure specific properties are different. Just as

Jan 1, 1962

By W. S. Ayres

BACK in the early nineties the old Dickerson iron mine in Morris county, N. J., was operated by a vertical shaft 850 ft. deep and by a continuing slope for more than 1000 ft. more 011 an incline of 65", together making the vertical depth about 1800 ft. I was then the general superintendent there. This mine, named for a former governor of New Jersey, had been worked more or less continuously from long before the American Revolution and up to this particular time. The pumping equipment was of the old-time Cornish type, with its long pump-rods running down the vertical shaft and the slope to the sump at its bottom. It was operated by a large flywheel engine in the engine room and all angles were turned by the usual bobs. Saturday was the day fixed for lowering the "suction" into the deepened sump at the bottom of the advancing slope. The mine foreman had gone down with the morning shift to superintend this very vital and particular work, which consisted not only of lowering the "suction" into the sump immediately after the pump had been stopped, but of securing it to the rock and putting in the added sections of column-pipe and of tightening up the numerous bolts at their joints, all before the water rose to the point of working. At an appointed time during the forenoon I had agreed to go down into the mine and join the mine foreman in consultation over any difficulties that might have arisen. At the time agreed I went down by the cage to the bottom of the vertical 850-ft. shaft, and then by ladders down the slope for over 1000 ft. more.

Jan 1, 1930

NEW MEMBERS The following list comprises the names of those persons who became members during the period of July 10, 1917, to Aug. 10, 1917. ARNOT, STANLEY L., Engr., Plymouth Cons. Gold Mines; Ltd., Plymouth, Amador Co .2 Cal. BARRETT, LESLIE PARK, Asst. Geol.... Michigan Geological Survey, Lansing, Mich. BENNIE, JOHN WILLIS Gen&apos;l. Mgr., Shannon Copper Co., Clifton, Ariz. BRINTON, OWEN FUGATE Mgr., Admiralty Zinc Co., Quapaw, Okla. BRODERMANN, JORGE, Civil Engr., Compania Minera San Francisco, Havana,Cuba. BROWN, RICHARD HENRY JR., Sales Engr., Ingersoll Rand Co., 300 N. Broadway, St. Louis, Mo. BROWN, STANLEY Chile Exploration Co., Chuquicamata, Chile. BUDDECKE, WILLIAM A Pres., Point Milling & Mfg., Co. Mineral Point, Mo. BURGESS, GEORGE K., Physicist and Chief, Division of Metallurgy, Bureau of Standards, Washington, D. C.

Jan 9, 1917

NEW MEMBERS The following list comprises the names of those persons who became members during the period Aug. 10 to Sept. 10, 1915: Members ACOSTA, JOSE NICANDRO, Min. Engr. and Chem., Shannon Copper Co., Gleeson, Ariz. ANDERSON, AMIL. ABNER,. Met Homestake Mining Co., Lead, S. D. BARB, P. A Apartado 92, Pachuca, Hid., Mexico. BERGH, SVEN VILHELM,. Min. Engr Rorstrandsgatan 32, Stockholm, Sweden. BOAS, Ross H., Min. Engr:, Care Highland Boy. Mine, Bingham Canyon, Utah. BONSALL, JAMES MALCOLM,.Chem., Copper Queen&apos; Reduction, Works, Douglas, Ariz. BOWLES, Ross., Supt. Of Smelters,. Granby Min. & Smelt. Co., East St. Louis, Ill. BRIGHT, GRAHAM, Engr., Westinghouse Electric & Mfg.. Co., East Pittsburgh, Pa. BUTLER, RICHARD,. Min. Engr., Mines. Supt., Lindal Moor Mines, Ulverston, Lancashire, England.

Jan 10, 1915

By D. C. Hilty

It has long been known that in melting high-chromium steels, some of the carbon might be oxidized out of the melt without excessive simultaneous oxidation of chromium, and that higher temperatures favor retention of chromium. The advent of oxygen injection as a tool for rapid decarburization of a steel bath permits significantly higher bath temperatures, and it was quickly recognized that the use of oxygen injection facilitated the oxidation of carbon to low levels in the presence of relatively high residual chromium contents. Up to the present time, however, specific data pertaining to the chro-mium-carbon-temperature relations in chromium steel refining have not been available. Individual steelmakers have evolved practices more or less empirically, but there has been very little real basis for predicting how effective any given practice can be in permitting maximum oxidation of carbon with minimum loss of chromium. The current investigation, therefore, was undertaken in an effort to establish the fundamental carbon-chromium relationship in molten iron under oxidizing conditions. As reported below, the equilibrium constant and the influence of temperature on that constant have been derived for the iron-chromium-carbon-oxygen reaction in the range of chromium steel compositions with what appears to be a fair degree of precision. The practical application of the result will be obvious. Experimental Procedure The laboratory investigation was carried out on chromium steel heats melted in a magnesia crucible in a 100-lb capacity induction furnace at the Union Carbide and Carbon Re- search Laboratories. The charges for the heats consisted of Armco iron, low-carbon chromium metal, and high-carbon chromium metal, the relative proportions of which were calculated so that the various heats would contain from approximately 0.06 pct carbon and 8 pct chromium to 0.40 pct carbon and 30 pct chromium at melt-down. When the charges were melted, the bath temperatures were raised to the desired level, and the heats were then decarburized by successive injections of oxygen at the slag-metal interface through a ½-in. diam silica tube at a pressure of 30 psi. The duration of the oxygen injections was from 30 sec to 2 min. at intervals of approximately 5 to 30 min. It did not appear that length or frequency of the injection periods had any significant effect on the results; cansequently, no effort was made to hold them constant and they were controlled only as was expedient to the general working of the heats. Between successive injections, the heats were sampled by means of a copper suction-tube sampler that yields a sound, rapidly-solidified sample representative of the composition of the molten metal at the temperature of sampling. This sampling device is a modification of the one described by Taylor and Chipman.1 An attempt was made to vary bath temperatures between samples, but it quickly became evident that, unless the variations were small or unless the new temperature was maintained for a minimum of 15 min. during which an injection of oxygen was made in order to accelerate the reactions, a very wide departure from equilibrium resulted. For most of the runs, therefore, temperature was maintained relatively constant at approximately 1750 or 1820°C. A few reliable observations at other temperatures, however, were obtained. Temperature Measurement The high temperatures involved in this investigation were measured by the radiation method, utilizing a Ray-O-Tube focused on the closed end of a refractory tube immersed in the metal bath. The immersion tubes employed were high-purity alumina tubes specially prepared by the Tona-wanda Laboratory of The Linde Air Products Co. These tubes were quite sturdy under reasonable mechanical stress at high temperature. They were unusually resistant to thermal shock, and chemical attack on them by the melts was slow. With care, it was found possible to keep these tubes continuously immersed in a heat for as long as 5 hr at temperatures up to 1850°C, before failure by fluxing occurred. The Ray-O-Tube—alumina tube assemblage was similar to those supplied commercially for lower temperature applications. In operation, the alumina tube was slowly immersed in the molten metal to a depth of approximately 5 in., and the device was then clamped solidly to a supporting jig where it remained for the duration of the run. A photograph of the equipment, in operation with Ray-O-Tube in place and oxygen injection in progress, is shown in Fig 1. When in position in a heat, the instrument was calibrated by means of an immersion thermocouple and an optical pyrometer. For calibration through the range of temperatures from 1500 to 1650°C, a platinum -platinum + 10 pct rhodium thermocouple in a silica tube was immersed alongside the alumina tube. Output of the Ray-O-Tube in millivolts and the

Jan 1, 1950

By F. Hulsmeir

The increase in drilling activities in Venezuela noted during the latter half of 1932 continued, and 132 wells were completed in 1933 as compared to only 60 completed during 1932. Notwithstanding these new wells, 114 of which were producers, and also the appreciable increase in artificial lifting installations during the year, Venezuelan production was maintained at only a slightly higher level than in 1932, amounting to 120,356,000 bbl. in 1933 as compared to 118,167,000 bbl. in 1932. However, at the end of the year the daily average production of 358,-860 bbl. was 16 per cent higher than that at the end of 1932. Exports from Venezuela recorded an increase of approximately 4 per cent, totaling

Jan 1, 1934

By S. M. Bishoff

The disturbance of surface land to support the underground mining of coal requires several hundred acres to produce easily in excess of $1 billion in sales at a moderately sized mine over 20-30 years. Due to the recent influx of environmental legislation, these surface operations must now undergo complete reclamation upon permanent cessation of production. This reclamation procedure has become so complex that the cost of reclamation must be a major consideration in the design of a new mine. This presentation will discuss these costs as they may be methodically evaluated and surcharged as a percentage of the product price. When placed in the proper, logical perspective, it is anticipated that the obstacles involved in this process may be minimized.

Jan 1, 1985

By Roger L. Goin

Maintaining smooth haulage roads is a key to significant cost savings at Kennecott Copper Corp.&apos;s Bing- ham Canyon copper mine, located near Salt Lake City, Utah. The truck operations section of the mine moves an estimated 300,000 tpd of waste plus some ore to maintain a balanced production cycle. A three-year truck replacement program has produced a dramatic new look in both size and capacity of the truck fleet. Currently there are 95 haulage trucks in the Bingham fleet with capacities up to 150 t. The trend towards the larger haulage units places greater importance on overall truck availability. The impact of a 150-t truck being out of service is far more critical than with the former 65 or 85-t units.

Jan 12, 1974

By R. F. Janke, J. F. Bossler

Introduction The commercial use of ion exchange resins to recover uranium evolved in the decade following 1950 when significant efforts were made to recover this vital element economically and efficiently from low grade ores. It was discovered that in both acid and alkaline systems, uranium exists as an anionic complex. This led to the application of anion exchange resins to concentrate and purify the uranium product. While this is the simplest statement of what an ion exchange resin does in the recovery of uranium, it should not be forgotten that the industry is continuing to evolve new methods in mining and processing which affect ion exchange operation. The inception of solution mining, the use of expanded bed ion exchange columns and the development of continuous ion exchange systems represent several examples of this continuing evolution in the industry. Throughout all of the changes in equipment designs and variations in solution compositions, the purpose of the ion exchange resin remains the same - to concentrate and purify uranium. Ion Exchange Resins When evaluating ion exchange resins for a uranium recovery project, the task that faces the chemist or process metallurgist is an assessment of the efficiency and, therefore, the economics of the various candidate resins for a given project. This assessment should include consideration of both physical factors such as particle size, density, hydraulic expansion and pressure drop as well as chemical factors such as the uranium loading and elution characteristics. For any given application, the differences in the physical and chemical behavior of ion exchange resins are a function of the conditions used to manufacture those resins. Therefore, an understanding of the way in which manufacturing variables affect resin behavior is important. Since most uranium recovery projects are concerned with recovery of the anionic complexes of uranium using anion exchange resins, this discussion will be restricted solely to the family of anion resins. The majority of the ion exchange resins used in commercial recovery operations look similar to the resins shown in Figure #1. [ ] Most of these materials are based on a styrene- divinylbenzene copolymer. The liquid monomers, styrene and divinylbenzene, are charged to a co-polymer reactor containing water. The water insoluble monomers are then mixed with the water to suspend oil-like droplets of the monomer mixture in. the water. The entire reaction mixture is then heated causing the monomers to polymerize into sol id thermoset plastic spheres. The spherical nature of the particle, the particle size distribution and the primary crosslinking level are fixed in this step in the production process. Figure 2 is a simplified illustration of this step of the process. [ ]

Jan 1, 1979

By Donald R. Williamson, Edward R. Mueller

Cyprus Pima Mining Co.&apos;s open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. Over the years, a number of attempts have been made to refine and polish the ore reserve figures using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results.

Jan 1, 1978

The Bougainville ore body was discovered in 1964 by a partnership of Conzinc Rio Tinto of Australia and New Broken Hill Consolidated Limited. The ore body is a porphyry copper in a fine-grained quartz diorite, which intrudes andesite volcanics and is located at an elevation of about 2, 000 ft in the Crown Prince Range of Bougainville in the Solomon Islands. Mineralization is predominantly chalcopyrite with some bornite and some gold and silver present. Rainfall in the area amounts to 200 in. (5. 08 m) per year. An active volcano is situated only 24 miles (38.4 km) from the mine, and all structures were designed to resist seismic shocks. An interesting and unique feature of the Bougainville operation was that the overburden was stripped with hydraulic monitors. Bougainville Copper, at 90,000 tpd, is the largest copper concentrator to be designed and constructed at one time; and besides the twin 54 in. by 74 in. Allis-Chalmers gyratories, it features seven 7 ft (2. 13 m) standard and fourteen 7 ft shorthead crushers, in addition to nine 18 ft diameter by 21 ft long (5. 5 m by 6. 4 m), 4250 hp, single -stage ball mills. During the design stage of the Bougainville primary crushing plant, several alternates were studied because the ore was expected to break with the production of large amounts of small-sized particles but with a minimum of fines. These alternates included two 54 in. by 74 in. gyratories with grizzlies, two 60 in. by 89 in. gyratories, and one 72 in. by 96 in. gyratory, the latter two installations without grizzlies. The two 54 in. units with grizzlies were finally selected as giving good reliability and the ability to handle the large amounts of small material in the feed. As originally installed, grizzly bars were set at 8 in. (203 mm); but, in an effort to perform more interparticle crushing in the primary and less rock-on-steel crushing in the secondaries and tertiaries, a test is underway (1976) to determine the effect of using 6 in. (152 mm) grizzly spacings (see write -up on Anaconda&apos;s crusher at Butte). The Bougainville ore is mined with 17 cu yd (13 cu m) shovels and hauled in 105, 170, and 210 st trucks to the crushers, which are equipped for two-side dumping. Up to 40% of the ore passes the grizzlies, which are equipped with splitters; and additional horizontal splitter bars are located directly above the spider caps. Because of the grizzlies, the crushers are supported by unique U-shaped enclosures, which are in turn supported by the end and center walls of the installation.

Jan 1, 1978

IRVING. PERRINE, Hutchinson, Kans.-I think in reading this paper one should hear in mind its relation to Dr. David White&apos;s paper on "Some Relations in Origin between Coal and Petroleum."&apos; In that paper he discusses the relationship between the percentages of fixed carbon in the coals, the gravities of the oils, and commercial gas possibilities. His paper has a map showing certain areas which Dr. White believes to be hopeless as far as oil and gas possibilities are concerned. THE CHAIRMAN (C. W. WASHBURNE, New York, N. Y.).-I. would like to emphasize one point brought out by Professor Schuchert.2 The southern hemisphere has had an exceedingly monotonous geological his-tory, except the northern border of Africa, the eastern border of Aus-

Jan 12, 1919

By John Birkinbine

IN the spring of 1878 the Pine Grove Furnace, located in Cumberland County, Pa., was blown in after lying idle for several years. The furnace was constructed in 1770, and for over a century it has been in almost continual operation. The plant consisted in 1877, when the writer was first called there, of a stone stack 32 feet in height, inclosing a shaft and boshes, the latter being 8 feet in diameter. The blast was supplied by two wooden blowing-tubs discharging into a third, having a floating piston sustaining a box weighted to give the desired pressure, the power being furnished by a waterwheel. A small 18-pipe hot-blast stove heated the blast. The furnace was remodelled during the winter of &apos;77-78, and a Weimer blowing-engine with a blowing-tub 5 feet in diameter and 2 feet stroke, and the necessary boilers, were substituted for the wooden tubs and water-wheel. The stack was raised and enlarged, and provided with a bell and hopper having a central drop. Water dam and tymp were added, and general repairs were made. The hot oven, however, was riot increased. The furnace had always been operated with charcoal as fuel, and its reconstruction was made with a view to continue the use of charcoal, but provision was made for ample blowing capacity should other fuels at any time be employed. Although liberal arrangements had been made in cutting wood, the stock of charcoal supplied in 1878 was insufficient for the increased requirements of the remodelled plant, and notwithstanding the purchase of some 80,000 bushels from an adjacent idle furnace, there was riot enough to keep the furnace in constant blast until a new supply could be obtained, particularly as the season was unusually backward. Instead of following the established precedent of many charcoal furnace managers, i. e., blow out every February, it was determined to continue in blast, using coke as fuel. Accordingly, when the charcoal stock was exhausted, on March 22d, 1879, Connellsville coke was substituted, the change of fuel being made at once; that is, the coke charges followed immediately upon the last charcoal charges. After working a few days,-the strike in the Connellsville coke region cut off the supply, and anthracite coal was obtained, a mixture of the two fuels being employed. The strike continuing,

Jan 1, 1880

By R. S. Sherwin

The extractive metallurgy of primary aluminum from its ores is discussed with special attention to the production of alumina from high grade ores by the Bayer process, including differences between American and European practice and a brief description of some processes for lower grade ores and the electrolytic reduction of the oxide to aluminum. METALLIC aluminum is not found in nature, but the oxides, hydroxides, and especially the silicates are plentiful. The estimated percentage of in in the crust of the earth is about 8 pct while that of iron is about 5 pct. By far the larger portion of this is combined with silica in the form of various clay minerals and igneous silicate rocks. From the point of view of extractive metallurgy of aluminum, these are low grade ores while the better qualities of bauxite are the high grade ores. There have been various definitions of bauxite but perhaps the best definition at the present time is that bauxite is a rock or earth commonly used as an ore of aluminum or its salts in which the aluminum is present predominantly as a hydrate or a mixture of hydrates and hydrous oxides. It contains varying amounts of oxides of silicon, iron, and titanium and traces of compounds of some of the less common elements. The silica is mainly combined with alumina as clay or clay minerals which are hydrous aluminum silicates, although a part of it may be present as quartz sand. On the American continents, the alumina is mainly present as gibbsite, Al2O3 . 3H2O, and the same may be said of the best known deposits of the Dutch East Indies and some of the deposits in India. In France and other countries in Europe as well as in Africa, the alumina is present mainly as boeh-mite, A12O3 . H2O, but in some of these deposits it is mixed with minor amounts of gibbsite. Some other deposits, such as those in the islands of Haiti and Jamaica, evidently contain two or more hydrates or hydrous oxides of alumina in varying proportions. Perhaps the main portion of the alumina may be present as gibbsite and boehmite with the proportion between the two varying rather widely. In the silicate minerals, including clay, the alumina is chemically combined with silica and has not been separated satisfactorily by mechanical or physical ore-dressing methods. Low grade bauxites are mixtures of hydrates, usually gibbsite or boehmite, with clay, iron oxides, etc. In some low grade bauxites, it is possible to separate a portion of the gibbsite or boehmite, which may be present as relatively hard and coarse particles, from soft or finely divided clay minerals by log washing or similar methods. This has been applied to the product of some mines or parts of them, but on other ores it is not applicable. In some cases the gibbsite or boehmite is almost as fine and soft and of nearly the same specific gravity as the clay minerals so that washing and gravity separations are not successful. The iron oxide, the clay minerals, and a part of the titanium minerals are often so finely dispersed in the ore that any of the physical mineral separation methods, including separations by gravity, particle size, flotation, and electrostatic or magnetic separation, have not been commercially SUCCESSFUL except on relatively small lots of ore. For these reasons, the only available methods of separation on the general run of ores have been methods which would be classed as chemical rather than physical or mechanical separations. Aluminum oxide can be reduced by carbon at temperatures above 1800°C to form metallic aluminum and aluminum carbide or nitride. The temperature for rapid reduction of aluminum oxide to metallic aluminum is about the boiling point of aluminum and above the temperatures necessary to reduce iron, silicon, and titanium so that the direct reduction of an aluminum ore with carbon will produce an alloy of aluminum, iron, titanium, silicon, etc., which may be mixed with carbides and nitrides. Also a large amount of the reduced aluminum may be lost as a vapor except in the presence of some alloying agent such as copper or other metals. While it is possible to refine such alloys or mixtures so as to produce commercially pure aluminum, the methods which have been found are too expensive for the present market. One direct reduction method which found limited commercial use in Germany during World War II was the direct reduction of a mixture of clay containing very little

Jan 1, 1951

By Larry Kaufman, Martin Schatz

The effect of pressure on the extension of the ? loop in the FeSi system has been determined by means of metallogvaphic studies and hardness measurements performed on a series of high-purity Fe-Si alloys containing 7.5, 11.0, and 13.9 at. pct Si, respectively. These mensurements, performed at 42 kbar and temperatures up to 1200oC, indicate that the ? loop is expanded to about 10 at. pct Si at 42 kbar as opposed to a maximum extension of 4 at. pct Si at 1 atm. Comparison of the experimental results with thermodynamic predictions of the pressure shifts yields satisfnctory results. DURING the past few years, several studies have been performed in our laboratory1-&apos; in order to determine the effect of high pressure on phase equilibrium in pure iron and iron-base alloys. The purpose of these studies has been to elucidate the effects of high pressure experimentally and to compare the observed results with predicted pressure effects derived on the basis of known thermody-namic and volumetric data at 1 atm. These studies have included work on pure iron2,5,7 as well as Fe-Ni,1,5 Fe-cr,l,5 and Fe-c4-6 alloys. In addition, Tanner and Kulin3 have reported results of pressure studies on two Fe-Si alloys containing 2.0 and 6.25 at. pct Si. At the time of this latter study, no detailed information was available concerning the difference in volume between the a (bcc) and ? (fcc) phases in the Fe-Si system as a function of silicon content. In order to compare their observations with calculated pressure shifts, Tanner and Kulin were forced to assume that silicon had no effect on the difference in volume between a and ? iron. The resulting discrepancy between their calculation of the a/? phase boundary at 42 kbar and the observed results led them to the conclusion that silicon additions probably decrease the difference in volume between a and ? iron. Recently: Cockett and Davis8,9 have reported de- tailed studies of the lattice parameters of a series of Fe-Si alloys at temperatures ranging from 20" to 1150°C. These measurements, performed on alloys in the bcc and fcc range, show that silicon does indeed decrease the difference in volume between a and ? iron. By correcting the calculations of Tanner and Kulin in line with the observed effect of silicon they were able to show improved agreement between computed and observed pressure shifts.&apos; The present measurements were undertaken to provide additional corroboration of this effect, by extending the range of composition, in addition to exploring a situation where large extensions of a ? loop could result in impingement of the ? field with an ordered bcc phase (based on Feo.75Sio.25). I) EXPERIMENTAL PROCEDURES AND RESULTS The alloys investigated were obtained from Dr. F. Kayser of M.I.T. They were prepared at the Ford Scientific Laboratory by vacuum melting electrolytic iron and high-purity silicon. The melts were poured under an argon atmosphere into hot-topped steel molds. Subsequently the ingots were hot-worked down to 1/2-in.-diam rods. Three alloys containing 7.5, 11.0, and 13.9 pct Si were studied. Carbon, regarded as the principal impurity, analyzed at, or below, 0.001 wt pct for all of the alloys. Prior to pressure-temperature treatment, the rod was annealed for 24 hr in vacuum at 1000°C, water-quenched, and subsequently machined into 0.100-in.-diam by 0.100-in.-long specimens. Subsequent to machining, the specimens were again annealed and then examined metallographically. They were found to exhibit a clear coarse-grained ferrite similar to Figs. 10 and 110 of Ref. 1 and Fig. 2 of Ref. 3. Subsequently, specimens of each alloy were equilibrated at 42 kbar at various temperatures in supported piston apparatus.1,3,4,6 Three specimens, one of each alloy, were wrapped in platinum and exposed simultaneously. The pressure-temperature cycle consisted of increasing the pressure from ambient to 42 kbar at 25oC, heating rapidly to the desired temperature, holding for 15 min, and quenching to 100°C, followed by slower cooling to 25°C and pressure release. The temperature was measured with a Pt/Pt-13 pct Rh thermocouple which was not corrected for pressure effects. Subsequently, specimens were examined metallographically and by

Jan 1, 1964

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke&apos;s Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty&apos;s work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke&apos;s Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970