Search Documents

By John Tabor, R. B. Spivey

INTRODUCTION Shafts have been sunk in a number of ways. By and large, however, most have been sunk by drill, blast, muck, and slip form methods. Most methods have provided satisfactory means of completion. The major drawbacks to the conventional methods have been: (1) un- reliable cost estimates for completion; (2) unreliable rates of progress; and (3) unreliable integrity of the shaft lining. Recently , engineering design studies have been done that strongly indicate, that, by the use of existing proven technology, shafts can be completed faster, more cheaply, safer, and with a better lining that has been possible using conventional methods. THE METHOD The alternate method utilizes the techniques of big hole drilling, shield excavator tunnelling, and pre-cast concrete lining. Big Hole Drilling - Drilled shafts have been completed for several years and I don't intend to address the technology, only to point out the use of drilled shafts is an alternate method of shaft sinking. Ideally, in a multi-shaft mine, the first shaft would be blind bored and cased to a size, whereby it can handle the muck from the excavation of subsequent shafts. It should be an 8' to 10' completed diameter. The cost of such a shaft in sedimentary formations compares favorably with a conventional shaft. However, it is much faster. For additional shafts, the role of the drill is to complete small holes (3' to 4') to the desired horizon. This is merely a hole to allow slashing to a larger size with easier muck removal from an underground drift connected to the previously drilled shaft. The smaller holes, just as the larger one, should be cased and grouted into place so as to assure a smooth open hole. SHIELD EXCAVATOR Theory and History - Tunnelling Shields have been in common use for several decades, and steam powered shields were used in England over 100 years ago. The purpose of the shield is to provide temporary ground support, protect personnel during operation, and to house the excavating equipment. The excavating equipment approach has varied from attempts at a continuous or semi-continuous boring machine, the tunnel mole, to a mechanical or hydraulic digging arm. The shield may or may not be an active digging element. If not active, the boring tool or cutter is advanced ahead of the shield to full diameter and then the shield is moved up to the cutter, or the shield advances along with the cutter. If active, the cutter opens a conical free face, and the shield is either jacked forward so that the leading edge spalls rock to the free face or poling plates are thrust forward to spall to the free face. In either approach, various methods of muck removal are incorporated into the shield. These may be gathering arms, conveyors, or with moles, hydraulic transport, where the cuttings are sufficiently fine. The efficiency of the muck removal system is critical as excavation is rapid and the system could easily become muck-bound. Application to Shaft Sinking- Technically, the use of a shield to sink vertical shafts is no different than a tunnelling operation. It is, in fact, less complex in most respects. Muck and water removal are difficult in a blind-driven shaft. However, where an underground opening is available for handling muck and water, rapid shield sinking is possible, using a pilot hole for muck and water to fall through and be removed from below. The Tabor Mining Shield is basically a caisson approach, whereby, the ground is only seen at the face or bottom. It does have hydraulic jacks to force it downward and has segmented cutting edges which allows forepoling ahead of the shield. The hydraulic excavator allows mining in the center of the face around the previously drilled hole with the forepoling segments slabbing to this free face. First, the drilled hole is cased and grouted. The machine is a tube with an excavator. The work cycle is as follows: (1) The casing and grout are cut at predetermined intervals by shaped charges. (2) The casing is crushed by the excavator, removed from the hole and hoisted to the surface. (3) The excavator then rips out a face around the hole by digging the formation in tension and breaking the pieces

Jan 1, 1982

By Waldemar Lindgren

During the last 15 years much attention has been given to the " contact-metamorphic" ore deposits which mainly occur in limestone close to intrusive contacts. In general, these deposits are characterized by the association of magnetite and simple sulphides with the so-called L'contact-metamorphic" silicates. These silicates comprise garnet, epidote, vesuvianite, tremolite, wollastonite, diopside, hedenbergite, ilvaite, and many other rarer forms. The contact-metamorphic zones contain also in places minerals with boron, fluorine, and chlorine, like axinite, tourmaline, danburite, fluorite, and scapolite. There is also more or less quartz and coarsely recrystallized calcite. The simple sulphides embrace pyrite, pyrrhotite, chalcopyrite, galena, zincblende, more rarely arsenopyrite. On the whole, sulphantimonides and sulph-arsenides are rare. Deposits of magnetite or chalcopyrite or of both are most common. The deposits have an irregular or rudely tabular form, following main contacts, dike contacts, or stratification planes; they rarely extend for more than 1,500 or 2,000 ft. from the contact; far more commonly they only reach a distance of a few hundred feet from that surface. The deposits are usually formed by replacement of limestone, or allied calcareous rock. Apparently they are found both in relatively pure and in impure carbonate rock. The deposits are geoiogical bodies of a chemical and mineralogical character differing greatly from the adjoining intrusive rock and from the unaltered limestone. They are rich in silica and iron, with more or less of lime, magnesia, alumina, sulphur, and rarer metals like copper. The so-called contact-metamorphic silicates which form the gangue usually are coextensive with the metallic minerals, though of course not necessarily with the merchantable ore. All opinions agree in holding the deposits of epigenetic origin, later than the inclosing limestone. Regarding the origin of the metals and the genesis of the ores there are several opinions. 1. There are those who see in these deposits the result of concentration of material contained in the intrusive rocks by means of hot circulating

Jan 1, 1915

C. H. MATHEWSON, New Haven, Conn. (written discussion *).-In a recent discussion of Dr. Jeffries' paper on tungsten,1 J. C. W. Humfrey,2 after taking exception to certain of the author's ideas relative to the cohesion of A and C metal, expresses the opinion that future research is likely to develop a method of preparing tungsten possessing "mechanical properties in line with those of other metals." The present paper by Dr. Jeffries begins with a determination of comparative properties of tungsten, copper, and iron, in which much dissimilarity is apparent, and ends with a coherent explanation as to why much of this dissimilarity is natural and inevitable, thereby supplying theoretical means for visualizing the changing properties of metals in general, once certain fundamental facts are known. The author's reasoning is primarily from the standpoint of the amorphous theory and his principal achievement is the development of an idea f differential cohesion according to conditions of temperature, etc., between A and C metal (which was first plainly suggested by Rosehain and Ewen, in their papers on Intercrystalline Cohesion of Metals) along with associated ideas, so as to give us a really useful working theory. I have come rather reluctantly to believe in the amorphous theory, or some theory admitting a modification of the ordinary crystalline phase so as to permit differential properties within the conglomerate, mainly because in no other way does it seem possible to account for observed changes of properties with temperature, etc. The very best illustration f the competency f the amorphous theory in this respect is seen in this and other recent papers by the author. All fractures through normal or healthy metal that have been preceded by deformation are supposed, by Dr. Jeffries, to take place either through the amorphous phase or at certain boundaries between amorphous and crystalline material; his reference to fractures, both members of which are similar in appearance and do not reveal a preexisting coarse-grained structure because of a coating of amorphous metal, indicates his preference for the former interpretation.

Jan 5, 1919

By J. M. Avasthi

The DOE-funded (Contract No. DE-ACO3-77ET13108) Gulf Research & Development Co. (GR&DC) field tests of underground coal gasification in steeply dipping beds (UCG/SDB) were conducted in the North Knobs area, located 12.8 km (8 miles) west of Rawlins, WY. The site has a gently rolling, sparsely vegetated, semidesert terrain on the transition zone between a broad, flat basin (Great Divide Basin) to the west and the subdued mountains of the Rawlins uplift to the east. A comprehensive geotechnical program (Ahner et al., 1980) was essential to successfully complete the test program. Emphasis of the program was the subsurface characterization of the site and consisted of mapping, drilling and logging, core analyses, and hydrologic tests. The samples of lithologic units over- and underlying the G coal seam were tested in the laboratory for their modulus and strength. This program provided the required data necessary for designing surface facilities, input for permits, and ensuring correct placement of the process modules. The two UCG tests at the Rawlins site were conducted in the nominally 6.7 m (22 ft) thick G coal seam (rank-subbituminous B), dipping at 63°.

Jan 1, 1984

By George Watkin Evans

During the past ten or twelve years, the average reader of newspaper and magazine articles has been led to believe that enormous deposits of high-grade coal exist in the northland and that these can be mined for practically nothing. But much of the reputed glitter and attractiveness of Alaskan coals disappears when viewed at close range. Many areas of coal-bearing rocks are widely distributed geographically from Cape Lisburne, on Bering Sea, to Admiralty Island, south of Juneau. Bituminous coal is found at Cape Lisburne, on the Bering Sea, at Five Finger Rapids on the upper Yukon, and at Herendeen Bay and Chignik Bay; lignite is found on the Kobuck River, along the Yukon River from points near the mouth to Tonakat, near Rampart, at Dawson, on the east shore of Cook Inlet, and in the Tanana Valley, 50 mi. south of Nenana. The Susitna and Matanuska Valleys contain coal ranging from lignite to anthracite, and in the Bering Lake district, there are coals ranging from semi-bituminous to anthracite. No effort will be made to describe all of these fields, but the writer will confine himself to the four principal fields, namely, the Nenana field! in the interior of Alaska, tributary to the Fairbanks district; the Matanuska field, in the Matanuska Valley; the Kachemak Bay field on the east shore of Cook Inlet; and the Bering River field, east of the mouth of Copper River. Nenana Coal Field The Nenana field occupies an area east of the Nenana River 70 mi. (112 km.) southwest of Fairbanks and approximately 50 mi, from the town of Nenana, which is located at the junction of the Alaskan Railway and the Tanana River. It is on the northern flank of the Alaskan Range and occurs within the foothills of that district. The elevations range from 1000 to 4000 ft. (304 to 1219 m.). Future developments may prove the field to extend from a considerable distance west of the Nenana River to the headwaters of the Tanana River. The coal measures are of Tertiary age and are probably Eocene. They are not badly deformed by folding, but portions of the field show

Jan 1, 1922

By C. E. Agnew

The Eastern district, composed of New Jersey and eastern Pennsylvania, with its native ores, was the cradle of the iron industry of the United States. The district attained and held the leadership in production of pig iron for over 100 years, from pre-Revolutionary days to approximately 1875. The first shipment of Lake hematite ore was made in 1853. It was a small shipment, transported by a sailing vessel and a canal barge, but it was the beginning of the end of the supremacy of the Eastern district, although at that time the ore was supposed to be too rich to be successfully smelted with the block coal then in use at western furnaces. The iron made from the first shipment of Lake ore was worked into nails by the Sharon Iron Co., at Sharon, Pa. The writer's great-grandfather, David Agnew, and his brother, John P. Agnew, owners and operators of the Sharpsville furnace, Sharpsville, Pa., worked the shipment through a furnace. Because of this, the writer feels some satisfaction in having been one of a group that solved the problem of making profitable an operation using Eastern district ores exclusively. With the development of Lake mines, and the production and use of coke, the Middle West district gradually assumed the position of leadership in production; because, even though the ores were transported 1000 miles by water and rail, its cost figure on pig iron was better than that of the eastern producer whose furnace was next to his mine. Such a cost figure was possible because the ore was naturally rich in iron and reduced easily. It was possible to carry a heavy burden on the furnace, which resulted in large tonnage and low coke per ton of iron. This paper is in no sense a technical one. The purpose is to show that with the proper physical preparation of the Eastern magnetites they will reduce as easily as the Lake hematites, and because of the high iron concentration give the Eastern producer just as much advantage as formerly he was at a disadvantage in comparison with the Middle West producer.

Jan 1, 1938

By C. E. Agnew

The Eastern district, composed of New Jersey and eastern Pennsylvania, with its native ores, was the cradle of the iron industry of the United States. The district attained and held the leadership in production of pig iron for over 100 years, from pre-Revolutionary days to approximately 1875. The first shipment of Lake hematite ore was made in 1853. It was a small shipment, transported by a sailing vessel and a canal barge, but it was the beginning of the end of the supremacy of the Eastern district, although at that time the ore was supposed to be too rich to be successfully smelted with the block coal then in use at western furnaces. The iron made from the first shipment of Lake ore was worked into nails by the Sharon Iron Co., at Sharon, Pa. The writer's great-grandfather, David Agnew, and his brother, John P. Agnew, owners and operators of the Sharpsville furnace, Sharpsville, Pa., worked the shipment through a furnace. Because of this, the writer feels some satisfaction in having been one of a group that solved the problem of making profitable an operation using Eastern district ores exclusively. With the development of Lake mines, and the production and use of coke, the Middle West district gradually assumed the position of leadership in production; because, even though the ores were transported 1000 miles by water and rail, its cost figure on pig iron was better than that of the eastern producer whose furnace was next to his mine. Such a cost figure was possible because the ore was naturally rich in iron and reduced easily. It was possible to carry a heavy burden on the furnace, which resulted in large tonnage and low coke per ton of iron. This paper is in no sense a technical one. The purpose is to show that with the proper physical preparation of the Eastern magnetites they will reduce as easily as the Lake hematites, and because of the high iron concentration give the Eastern producer just as much advantage as formerly he was at a disadvantage in comparison with the Middle West producer.

Jan 1, 1938

By Zay Jeffries

IMAGINE a spinning sphere of hot matter about 8000 miles in diameter, rushing through space at a velocity measured in miles per second, and you have a rough idea of what our earth is supposed to have been like about two to four billion years ago. By applying all of the science known to man and, more especially, by determining the velocity of earthquake waves at different depths, making comparisons with meteorites, studying densities, compressibility of rocks and the nature of surface rocks, a fairly definite conception of the general constitution of the earth has been obtained.1 The earth is supposed to have a central core rich in iron containing a substantial amount of nickel and small percentages of several other elements. The density of the core is assumed to be about ten times that of water and the diameter about 4200 miles. An intermediate shell of density about 4, and thickness of about 1800 miles, is sup- posed to consist of heavy rocks including sulfides, oxides, and silicates. The outer rock shell, probably about 100 miles thick and with a density around 2.8, is thought to be composed mostly of silicates, becoming in general more siliceous as the earth's surface is approached. NATURE'S SMELTING OPERATION Nature seems to have subjected the earth to a stupendous smelting operation, burying beyond reach much of the metal that man recovers in his smelting practices. We live on the surface of Nature's "slag dump" and must be content, for the near term, to recover for man's

Jan 1, 1953

By S. E. Bretherton

MOST metallurgists appreciate the great need of a process for the extraction and recovery of valuable metals from complex ore, where the presence of one metal increases the cost of extracting the other metals to such an extent that not any of the metals can be extracted at a profit. We need only refer to some of the mines in Colorado, Utah, and New Mexico, where oxidation has taken place and the sulphur, zinc, copper, and some of the iron and other metals have been leached out, large bodies of oxidized ore remaining, rich in lead, silver, and sometimes gold. These metals have been concentrated by the removal of the other metals, leaving a very desirable ore for treatment in the blast-furnace for the production of lead bullion, and recovery of the silver and gold. If lead is not present, the gold and silver are usually recovered by some method of milling, or the ore is shipped to a smelter, where it is mixed with lead ore or copper-iron sulphide ore from some other mine. In these same mines, when developed to greater depth below the leached or oxidized zone, the ore is found to contain the original mixture of sulphur, zinc, copper, etc., added to, or I should say left with, the lead, silver, and gold values; but instead of adding to the value of the ore, the presence of these elements, especially zinc, makes the copper, silver, and gold of less value, and often worthless. Such was the experience of the oldest mines in Leadville, Colo., until methods of mechanical separation of the lead from the zinc were developed sufficiently to allow of some profit by the making of a concentrate rich in zinc to be shipped to the zinc smelter, and sometimes a lead concentrate which could be shipped to the lead smelter; but even in these cases the waste of the different metals is a very serious matter. In the very best concentrating plants some zinc will be left in the lead concentrate, to be lost and to give considerable trouble in the lead-smelting furnace. On the other hand, some of the lead, with a large percentage of the copper and silver, will follow the zinc into the zinc concentrate, to be, perhaps, recovered y smelting the cinder or clinker left in the re-

Jan 7, 1914

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole. The Calcite plant operates a limestone quarry near Rogers City, Mich., in the northern part of the lower Michigan peninsula. The formation quarried, a portion of the middle Devonian series, is the Dundee limestone, which is uniform, seldom massive, and characterized by definite bedding planes. The dip is southeast, 40 ft to the mile. Quarry faces vary from 20 to 116 ft in height. Vertical blastholes are used entirely, from three to five rows of holes being drilled parallel to the working face, spaced 18 ft apart with 18-ft burden and drilled 6 to 8 ft below shovel grade. Quarry operations coincide with the navigation season on the Great Lakes, as the bulk of the stone is transported by lake carrier. The normal operating season runs from April to December, the remaining time being devoted to stripping operations and plant and equipment maintenance. In the followirig discussion drilling rates mentioned refer to overall drilling time and include all operations such as moving from hole to hole, penetration and extraction of tools, and routine maintenance. Time consumed by such factors as power delays and major machine repair is not included in drilling time unless otherwise stated. Figures cover only operations at this one plant in the formation mentioned. Needless to say, a very different set of figures could be obtained in a different formation. However, the comparison of footage obtained with churn drills and rotary rigs in this particular formation has been used as an indication of what might be the expected performance of rotary rigs in other formations. Prior to 1950 the bulk of the blasthole drilling at the Calcite plant was done by electrically powered churn drills. Both crawler and wheel-mounted rigs were used. These machines, which mounted a 22-ft drill stem of 4½ in. diam and a spudding type of bit 2 to 4 ft long, drilled a hole of 5 ?-in. diam. Average drilling rate of these rigs in the Rogers City formation was 8 % ft per hr. In 1946 one of the first rotary blasthole drills offered to the quarry industry was put into use on an experimental basis. This machine, known as the Sullivan Model 56 blasthole drill, Fig. 1, was on 16-in. crawler pads and electrically powered at 440 v. The drill bit, a Hughes Tri-Cone roller bit of 5?-in. diam, Type OSC, was threaded into the end of the 4-in. square hollow drill rod or stem. These drill rods were 20 ft long with female threads on one end and male on the other to allow for addition of the desired number of rods for drilling holes of various depth. Rods were handled by a single drum hoist geared to the main drive motor and racked by a 30-ft derrick or mast when not in use. The cable from the hoist drum fed through a crown block on the top of the derrick back to the water swivel mounted in the top end of the drill stem in use. This cable remained attached during drilling operations and was used to hoist the tool string from the hole. Down pressure was applied to the tool string by means of a pair of 4-in. diam hydraulic cylinders acting on the drill chuck holding the drill rod. The first chuck consisted of flat jaws which gripped the flat sides of the stem. These jaws were controlled by set screws forcing them into contact with the drill stem. As these set screws had to be loosened and tightened by hand with each stroke of the hydraulic feed cylinders, there was great delay. For this reason the semi-automatic chuck was developed which automatically gripped the stem on the downward stroke but released for retraction of the hydraulic feed cylinders. Rotation was imparted to the tool string by a rotary table acting on the chuck and geared to the main drive motor through a separate gear train and clutch. A positive displacement water pump, mounted on the drill, fed water through a system of pipes and hose into the water swivel mounted on the top of the drill rod and through the rod and bit, washing the drill cuttings to the collar of the hole. Where water was scarce, provision was made to settle out the cuttings coming from the collar of the hole and re-use the water. Where water was abundant the stream coming from the hole was wasted. Drilling rate with this machine was about 20 ft per hr and bit life 1600 ft of hole. While this rate was more than twice that obtained with the churn drills employed, the problem of water supply and drill cuttings disposal rendered the machine impractical from an operating standpoint. Consequently it was used only in that part of the operation for which water was easily supplied, when the character of the formation made it least difficult to wash cuttings away from the collar of the hole. In October 1949 it was suggested that drill cuttings be removed by compressed air, long used for this purpose on pneumatic drills, and collected at the collar by suction. Thereafter, the water pump on the Sullivan 56 was replaced by a 500-cfm air compressor and a trial run made. Air pressure at

Jan 1, 1955

By W. H. Meyer

Although an aerial photograph is not a map, most of the information that is necessary for compiling a map is recorded in the photograph provided some form of radial-line method is used to determine the true position of images. The slotted- templet method, which is based on the well-established radial-line principle, has made it possible to construct accurate mosaic maps at a cost comparable with that formerly charged for the average mosaic. It makes possible the securing of these results with far less ground control, which is always expensive. It has expanded widely the possible use of aerial photographs for mapping. ALTHOUGH a vertical or oblique aerial photograph is not a map, most of the information that is necessary for compiling a map is recorded in the photograph. Some ground controls or data are needed, the number and accuracy to be governed by the mapping method to be used and the scale and final accuracy desired in the finished map. RADIAL-LINE CONTROL It is essential that the principle of radial-line control in the use of vertical aerial photographs be understood and accepted before any confidence in the slotted-templet method can be gained. A simple sketch and some enlargements showing the Empire State Building will serve to illustrate the cause of displacement of an image that is above the datum plane as recorded in the photograph. The top of the tower of the Empire State Building is directly above the base, and when the image of the top is shown almost two blocks away from the center of the base, it is evident that the image of the top of the tower is not the true location, and in this particular case we know where the true location is; namely, over the center of the base of the tower. If the top of the tower were the top of a hill 1250 ft. high, we would have no way of knowing by inspection the true position of the top of the hill, so it is very important to have a method whereby the true location of any such point can be determined, and thereby make it possible to convert the detail of an aerial photograph into accurate information for mapmaking.

Jan 1, 1939

By Howard L. Hartman, Burke O. Trafton

There is a fruitful area of computer competence which has gone virtually unnoticed by the mining industry. This is in the solution of its numerous fluid-flow distribution problems, involving the circulation of air, water and other fluids in conduits through mines. Typical of these is the mine ventilation system, which circulates air through mine openings to the working faces. The networks of interconnected airways in large mines-often resembling a tortuous maze or labyrinth defying representation by schematic, let alone solution-must somehow be resolved and analyzed, if effective and safe control of the ventilation is to be maintained. These are admirably suited to programming for solution by high-speed electronic computer. Not only can direction of flow be determined but quantity and head loss as well. EARLIER EFFORTS AT NETWORK SOLUTION The only prior attempt to solve mine ventilation networks by digital computer methods was made by a Japanese investigator1 in 1958 whose work went unpublished. Unfortunately, he employed a method of network analysis little used in the United States and one which could accommodate a maximum of only 30 airways. While his analysis seems unnecessarily cumbersome and involved, it did suggest that a digital computer approach was feasible.

Jan 9, 1963

By S. W. Parr, F. B. Hobart

Studies relating to the behavior of coal toward oxygen may have for their purpose the determination of the fundamental factors that underlie spontaneous combustion, weathering and deterioration, and the general topic of storage, as well as those properties that have to do with the underlying principles of carbonization. There is also involved the possibility of developing information relating to the constitution of coal, or at least the chemical properties inherent in the type substances of which the coal is composed. It is the purpose here to record certain results bearing on this latter idea of the chemical properties that characterize the main constituents of bituminous coal. The avidity of freshly mined coal for oxygen has long been known. What happens to the coal or to the oxygen is not so clear. Is the oxygen absorbed or chemically combined, and what are the conditions as to time, temperature, texture, or components that are most involved in the phenomenon? If we subject a weighed quantity of coal maintained at a constant temperature to a current of oxygen, we may obtain three factors of interest—the weight increase of the coal, the weight of the water, and the weight of the carbon dioxide formed in the reactions involved at that

Jan 1, 1925

By C. M. Smith

PILOTED by Cadwallader, Evans, Jr., as chairman, the Coal Division got under way Monday morning for the first of three consecutive sessions. N. F. Patton started the ball rolling with a paper on the economics of anthracite distribution, which was ably discussed by H. J. Rose, W. S. Blauvelt, and others. Mr. Patton pointed out many incongruities in freight rates, dealers' margins, and other factors which are disturbing the distribution of anthracite, one result being that trucks are hauling at least six million tons of anthracite annually, half of which is stolen. In the discussion of the papers the desirability of greater uniformity in the production and shipment of coal from month to month was urged; with larger summer price concessions as a means toward this end. "Performance Expectancy of Domestic Underfeed Stokers for Anthracite," by Allen J. Johnson, brought this important platter down to date by showing the range in capacities and efficiencies to be expected from well-made stokers, and by detailing other of their operating characteristics. One of his most interesting points is that the efficiency of domestic stokers is practically equal to that of handfiring for good installations and operations of both

Jan 1, 1935

By C. Norman Bowers, Blaine B. Wescott

MARKED improvement in the serviceability of sucker rods has been effected in the last two years, partly because of the insistent necessity for greater economy in the operating costs of crude oil production growing out of the general industrial depression and partly because many of the recently developed fields have imposed more severe operating conditions upon both surface and underground equipment. The latter is particularly true of Kansas, where practically all of the oil produced. is associated with damaging amounts of hydrogen sulfide brine and where the method of establishing potential production demands equipment capable of being operated at maximum capacity without interruptions. The decline of flush production in the Oklahoma City field created new problems in deep-well pumping on a scale heretofore unequaled and the increased proportion of water it has been necessary to produce in the fields of the Greater Seminole area presented conditions that were acutely in need of betterment. The problem in the latter fields was complicated by the shift towards sulfide characteristics, which accompanied water encroachment, and it is probably true that nowhere, at the present time, are pump¬ing conditions generally as severe as in this territory. The Mid-Continent district, therefore, has become the proving ground for the numerous materials that have been proposed for sucker-rod fabrication. The information that ultimately will be obtained from an unprecedented amount of field experimentation will pay ample dividends when the decline of East Texas increases the demand for the vast reserves of sour crude in West Texas. It is a rare occurrence in industry that the use of such a simple piece of equipment as a sucker rod presents so complicated a problem for solution. As proof of this, it is only necessary to consider the numerous types of sucker rods on .the market at the present time and contrast this condition with that of less than four years ago, when it was the common aim of manufacturers to develop a single sucker rod for all conditions of

Jan 1, 1935

By A. H. Kline, E. B. Zimmer, Zay Jeffries

It is well known that many properties of a given metal vary with the size of grain or cell. For most industrial purposes, where high ultimate strength and high elastic limit are desired, the manufacturer tries to produce a fine-grained structure. For some purposes, for example in transformer iron, a coarse-grained structure is desirable. The terms fine-grained and coarse-grained are used only in a relative sense. For example, a fine-grained cast copper might have grains 100 times larger than coarse-grained high-speed steel. Similarly, a finegrained steel rail might have grains or cells 100 times larger than coarsegrained wire, which was made of steel from the same heat. In some metals, the change in grain size is more appreciable khan the changes in any of the properties determined by the tensile test. Furthermore, in metals which have been annealed or subjected to high temperatures, grain size may prove to be a better indication of the life of the metal in use than the tensile test. One of the authors was able to supplant the tensile test with grain-size determinations in the control of metal for a specific use, the latter determination being more indicative of the life of the metal part than the tensile test. A grain-size determination with a tensile stest is, of course, more valuable than either singly. At present there is a decided dearth of data on actual grain-size determinations in metals, and consequently a corresponding lack of ability to interpret the determinations after they are made. It would be desirable to have correlation made between grain size and properties of metals, comparing thousands of determinations. In this way, grain-size determinations might be interpreted in much the same manner that tensile tests are now. Several Methods of Measuring Grain Size One of the chief reasons why more grain-size measurements have not been made is the excessive work involved in making a determination.

Jan 1, 1916

By J. B. Hess, R. L. Dietrich

IN the mechanical twinning of magnesium on the {1012} planes the crystallographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only under tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [ 1120] fibers,1 the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to {1012 } twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or untwinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw3,4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig 1 is the pattern of an uncompressed specimen of AZ31 alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on {1012} planes produced an 86° reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1948

By Frank Rieber

The discovery that strongly magnetic bodies localized near the surface of the earth could be detected by the distortion which they produced in the resultant magnetic field marked the beginning of magnetic surveying methods. From an original ability to detect bodies of magnetic iron ore and the like when located very close to the surface, these methods have been extended until today they promise to give much information with regard to the structure of such slightly magnetic material as sedimentary rock containing only a very small proportion of iron.' The recent extensions have been made possible through the development of more delicate instruments, and of methods for their use. From the original compass and dip needle, the design of apparatus has progressed until equipment is typified by magnetic balances capable of measuring the components of the earth's field to an extremely high degree of accuracy. It seems unlikely that the limit of such instrumental development has been reached. Just as the change from compass and dip needle has enabled the location of relatively minor changes in magnetic materials, so additional developments in the direction of increased sensitivity, as well as in greater dependability and constancy of operation, should reveal positively many slight changes which either escape notice in the present surveys or are so small that they cannot with certainty be separated from uncontrollable errors due to inconstant operation of the equipment. The ability to read smaller and smaller variations does not mean, of course, that deductions as to the causes of these variations will be made as accurately and definitely as is possible with the more pronounced anomalies.

Jan 1, 1929

By John A. Shelton

One of the heaviest burdens uselessly cast by our mineral land laws upon the holder of the title conveyed by a patent from the United States is due to the provision excepting known veins from land patented as placer. In many instances the expense of defending such titles from the assaults of the owners of lode locations made upon the theory that the veins so located were known to exist at the date of the placer application for patent has exceeded many times the value of the land in question. Neither the lapse of time, however long after the issuance of the patent. nor repeated adjudications by the courts serve to quiet such titles Or to prevent them from being questioned. In the passage of laws providing for the acquisition of title to the mineral lands of the United States, Congress provided that the title to known veins should not pass from the United States by a patent based upon a placer location. As construed by the courts, the law (Sec. 2333 R.S.U.S.) provides that the applicant for a patent upon a placer claim may, if any vein of sufficient value to justify the expenditure of money in its development is known by him to exist within the boundaries thereof, include in his patent application an application for patent upon the vein as a lode claim; and failure to do so is to be deemed a conclusive declaration that the applicant makes no claim to the vein nor to an area of surface ground extending for 25 ft. (7.6 m.) on each side of its middle or center. As to such vein and such area of enclosing surface ground under the circumstances stated, the title remains in the United States notwithstanding the issuance of a patent that purports to convey the entire surface of a described area and everything beneath it, excepting only the segments of veins the apices of which lie outside of such area. Such known veins with such area of enclosing surface ground are, of course, at any time, so long as they remain unlocated, subject to location and appropriation in the same manner as other. veins upon the public domain. The history of the operation of this law in one district will serve to illustrate its effect generally throughout the mining regions of the United States. In the Butte district, the mineral that first attracted the atten-

Jan 1, 1920

By J. B. Hess, R. L. Dietrich

In the mechanical twinning of magnesium on the {1012} planes the crystal-lographic deformation is such that, in the direction of the hexagonal axis [0001], twinning is possible only undef tension stress, while in the directions perpendicular to the hexagonal axis, twinning is possible only under applied compression. Thus in extruded magnesium and magnesium alloys where the extruded textures are best described as either [1010] or [1120] fibers,' the basal planes are all nearly parallel to the extrusion axis and such material is susceptible to ( 1or2 ) twinning by compression in the direction of the extrusion axis. In order to explain the results of cyclic stressing in alternate tension and compression upon the tangent elastic modulus in such material, Dorn and Thomsen2 have postulated that, following twinning under applied compression, a retwinning or un-twinning occurs as a result of residual microtensile stresses immediately upon removal of the applied compressive force. Recently, Carapella and Shaw4 have used this supposition of untwinning in magnesium in discussing their results on indentation hardness and on cold drawing of MI sheet. In trying to confirm this hypothesis by suitable direct experiments, the authors have been unsuccessful in detecting any evidence whatsoever that untwinning follows the release of applied compression and are forced to conclude that this hypothesis is improbable or, at least, that the quantity of material involved is small. For the experiments, small cylindrical specimens 0.040-in. diam. X 0.120- to 0.140-in. long were etched from 0.0625-in. extruded rod. The ends of the specimens were accurately faced off parallel in a jeweler's lathe. The compression jig was simply an ordinary set of micrometer calipers with an anvil interposed between the spindle and the specimen. The anvil was free to move axially but restrained from rotating so that the rotation of the spindle would not introduce a twisting stress on the specimen. With this arrangement the compressive strains could be estimated to 0.0001 in. and X ray pinhole photographs could be taken with or without load as required. Fig I is the pattern of an uncompressed specimen of AZ3I alloy, showing the approximate [1010] extrusion fiber. The X ray beam is normal to the extrusion axis; in this position it is particularly sensitive in detecting twinning if one directs his attention to the diffraction ring from the basal plane. Since twinning on (1072 planes produced an 86" reorientation of the crystal lattice, the original basal reflections occur at the 3 and 9 o'clock positions while the (0002) reflections from any twinned material will occur at the 6 and 12 o'clock positions. Fig 2 shows the same specimen compressed 3.0 pct, photographed while still under load. This strain has been just enough to produce a detectible amount of twinning and the sensitivity is roughly indicated by the fact that no alterations were produced in the intensities or maxima of the other diffraction rings. A strain of

Jan 1, 1949