Search Documents

By Robert R. Abbott

The influence of various elements in retarding or accelerating the absorption of carbon during the process of carburization is fairly well known. In general those elements which form carbides accelerate the absorption, while those which do not retard it. It has sometimes been wrongly stated that those elements which raise the temperature of the critical range increase the absorption, while those which lower this temperature decrease it. Silicon is a notable exception to this rule, for its influence is to raise the critical range but to lower the absorption of carbon. Some elements which do not form carbides have no apparent influence upon the absorption rate. Carbon itself retards the absorption rate. With a view to obtaining more exact data upon the subject the following experiments were undertaken: 208 steels of different chemical composition were selected to represent most of the types of modern constructional steels. Specimens 2 in. in diameter and 9 in. in length were weighed to milligrams. They were then packed in the special carburizing box shown in Fig. 1, and kept in the furnace for 10 hours at a temperature of 900' C. A duplicate experiment was conducted at 1,000° C. At equal intervals of time the box was rotated in the furnace so that two complete revolutions were made in the 10 hours. This precaution was taken to neutralize as much as possible any effect of unequal heating. At the end of the 10 hours the box was allowed to cool in the furnace with the doors open. The specimens were then weighed again and the increased weight (carbon) determined. In the following table are given the analyses of the various steels, together with the increased weight of carbon expressed in milligrams.

Jan 1, 1914

By T. I. Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook' and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946

By J. Brian Eby, T. I. Harkins

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook' and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946

By Thomas Fraser, Abreu Alvaro

THE work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacionál da Produção Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operat¬ing practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being expanded and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining condi¬tions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern São Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up -to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1946

By E. T. Turkdogan, Klaus Schwerdtfeger, P. Grieveson

The rate of growth of "Fe4N" on a iron was measured by nitriding purified iron strips in flowing am -monia -hydrogen gas mixtures at 504" and 554°C. It is shown that a dense nitride layer is formed when a zone -refined iron is used in the experiments. With less pure iron, the nitride layer is found to be porous. Through theoretical treatment, the self-diffusivity of nitrogen is evaluated porn the parabolic rate constant, and found to be essentially independent of nitrogen actirlity, e.g., D* = 3.2 x l0-12 and 7.9x l0-12 sq cm per sec at 504" and 554?C. Some consideration is given to the mechanism of diffusion in the nitride phase. THERE is a great deal of background knowledge on the solubility and diffusivity of nitrogen in iron, and on the thermodynamics and crystallography of several phases in the Fe-N system. Although case-nitrided steels have many applications in practice, no work seems to have been done on the diffusivity of nitrogen in the iron nitride, ?', phase. The only work reported on the related subject of which the authors are aware is an investigation by Prenosil,1 who measured the growth rate of the e phase on iron by nitriding in ammonia-hydrogen gas mixtures. EXPERIMENTS Purified iron plates of approximate dimensions 1 by 0.5 by 0.03 cm were nitrided in flowing mixtures of ammonia and hydrogen, in a vertical furnace fitted with a gas-tight recrystallized alumina tube. After a specified time of reaction, the sample was cooled to room temperature by withdrawal to the water cooled top of the reaction tube. The furnace temperature was controlled electronically in the usual manner within *l°C; the temperature was measured using a calibrated Pt/Pt-10 pct Rh thermocouple. For each experiment the iron strip sample was cleaned with fine emery cloth and degreased with tri-chloroethylene prior to the experiment. The ammonia-hydrogen gas mixtures were prepared from anhydrous ammonia and purified hydrogen using constant pressure-head capillary flowmeters. The gas mixture flowed upward in the furnace with flow rate of 400 cc per min at stp. The composition of the gas mixture was checked by chemical analysis at regular intervals. In most cases, the compositions of the exit gas and metered input gas agreed within about 0.3 pct, indicating that cracking of ammonia did not pose a problem at the temperatures employed. Two series of experiments were carried out using two different types of purified iron samples. In the first series of experiments at 550°C, vacuum carbon deoxidized "Plastiron" was used. The main impurities present in this iron were, in ppm: 4043, 50-Cr, 20-Zr, 40-Mn, 20-P, 20-S, 20-C, 50-0, and 10-N. In these experiments the rate data were obtained by measuring the change in weight of the iron specimen suspended in the hot zone of the furnace by a platinum wire from a silica spring balance. The nitride layer formed in these experiments was found to be porous, particularly near the outer surface. In other experiments, high purity zone-refined iron (prepared in this laboratory) was used. The total impurity content of this iron was 30 ppm of which 20 ppm was Co + Ni, 4 ppm 0, other metallic impurities were less than 1 ppm. The zone-refined iron bar, -2.5 cm diam, was cold rolled to a thickness of about 0.03 cm and the specimens were prepared for the experiment as described earlier. After the nitriding experiment, the sample was copper plated electro-lytically and mounted in plastic for metallographic polishing. After polishing, the thickness of the ?' layer was measured using a metallographic microscope. The nitride layer formed on the zone-refined iron was essentially free of pores. RESULTS The different morphology of the nitride layers grown on "Plastiron" and zone-refined iron is shown in Fig. 1. Both samples were nitrided side by side for 55 hr. The holes in the less pure iron, Fig. l(a), are confined to a region about one half thickness from the outer surface. The dense layer grown on zone-refined iron, Fig. l(b), is thinner than the porous layer on the "Plastiron". The impurities in the iron are believed to be responsible for the formation of a porous nitride layer. The pore formation may be due to the high nitrogen pressures existing within the nitride layer, e.g., the equilibrium nitrogen pressure is 1.2 x l05 atm in the 38.6 pct NH3-61.4 pct H2 and 6.6 x l03 atm at the Fe-Fe4N interface at 554°C and 0.96 atm. It is possible that the oxide inclusions present in the electrolytic iron may facilitate the nuclea-tion of nitrogen gas bubbles within the nitride layer. Support for this reasoning is the fact that pores are only encountered in the outer range of the layer where nitrogen pressures are largest. The photomicrographs in Fig. 2 show the effect of reaction time on the thickness of the dense nitride layer formed on zone-refined iron. These sections are from samples nitrided in a stream of 29 pct NH3-71 pct H2 mixture at 554°C for 22, 70, and 255 hr. In all the sections examined the nitride-iron interface was noted to be rugged. These irregularities are be-

Jan 1, 1970

By D. S. Eppelsheimer, D. N. Williams

The cold rolled textures of iodide titanium and of three samples of commercial titanium were examined using the Schulz-Decker Geiger counter technique. The iodide titanium and two of the three samples of commercial titanium showed a (0001) [1010] texture rotated 30' toward the transverse direction about an axis in the rolling direction. The third sample of commercial titanium showed a double texture. THE metals of the hexagonal system tend to deform similarly if the c/a ratios are similar. Thus titanium, zirconium, and beryllium, with c/a ratios of 1.601, 1.590, and 1.570, respectively,l should have similar cold rolled textures. The cold rolled texture of high purity iodide titanium has been described as (0001) [1010] rotated 30" toward the transverse direction about an axis in the rolling direction.' The texture of zirconium has also been reported as (0001) [1010] with a transverse rotation from the ideal position of approximately 30" about an axis in the rolling direction." This texture differs from that reported for titanium however since a continuous spread of (0001) poles toward the transverse direction was reported rather than distinct (0001) maxima 30" from the rolling plane normal. Beryllium has a texture similar to that of zirconium although the angle of transverse rotation of the (0001) poles is much less.' These three metals thus show a common type of cold rolled texture, as yet unexplained, which can be described as (0001) [1010] with various degrees of rotation toward the transverse direction about an axis in the rolling direction. Since titanium showed the greatest degree of rotation from the (0001) [1010] position, the cold rolled texture of titanium was re-examined using a semiquantitative Geiger counter X-ray technique to obtain more accurate experimental data from which a theoretical interpretation of this new type of hex- agonal rolling texture could be developed. The cold rolled textures of iodide titanium and of three samples of commercial titanium were determined. Table 1 gives the analyses of the titanium samples. Experimental Procedure Preparation of Samples: Prior to the final rolling operation each of the samples was given an initial reduction of approximately 50 pct and annealed to remove the gross effects of any previous treatments. Samples were annealed in vacuum, high purity helium, and air to determine whether annealing atmosphere had any effect on the cold rolled textures developed. All samples were annealed 1 hr at 800°C. Grain size determinations were made using the formula, 1.075 in which n is the number of grains counted in an area A (in sq mm) and M is the magnification of the area counted.' This formula gives the diameter between opposite flats assuming hexagonal grains. At least three areas containing more than sixty grains each were counted in each grain size determination. Rockwell B hardness readings were made on the annealed samples. The results of the measurements of

Jan 1, 1954

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By G. R. Frank, R. E. Willett, E. H. Hollingsworth

The most generally accepted equilibrium diagram for A1-Fe alloys has a eutectic system on the aluminum side with an essentially insoluble constituent of the formula, FeAl,, as the second phase. In 1938, Bradley and Taylor1 did report a phase change of FeAl,, but this change has never been confirmed. According to them, FeA1, is the stable phase only at higher temperatures; at lower temperatures, it is converted into Fe2Al7 and aluminum. It has now been found that there is, in fact, a phase change of the Al-Fe constituent on the aluminum side of the equilibrium diagram. This change, however, is not the one reported by Bradley and Taylor. The alloys used were cast by continuous processes and had these analyses: Fe - 1.98 to 2.02 pct, Cu-0.01 pct, Si - 0.01 pct, Mn - 0.01 pct, Mg - 0.00 pct, Zn - 0.00 to 0.01 pct, Cr - 0.00 pet, Ti - 0.00 to 0.04 pct. The constituent in these alloys was identified by X-ray analysis with a Guinier camera and by chemical and X-ray powder diffraction analyses. Two procedures were used to separate constituent for the last two analyses. In one procedure, it was separated by treating a sample with a solution of methanol saturated with iodine. And in the other procedure, it was separated by first applying, at 12 amp per sq ft in 15 pct sulfuric acid at 70°F, an oxide coating to a sample, and then dissolving this coating in a solution of 35 ml of 85 pct H3PO4 and 20 g of CrO3 per liter. Several observations directed attention to a phase change of the A1-Fe constituent. Differences that appeared too great to be accounted for by micro-structure alone were found in the voltages required to apply the same thickness of an oxide coating to products from rapidly and slowly chilled ingot. Even more striking was the difference in appearance of the coatings themselves. One applied to a product from a rapidly chilled ingot was dark gray in appearance, in fact, almost black, while one applied to a product from a slowly chilled ingot was essentially white. Also, even a short period of thermal treatment at an elevated temperature of products from rapidly chilled ingot led to the same anodizing behavior as that of products from slowly chilled in-

Jan 1, 1962

By R. G. Webber, F. C. Langenberg

During the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point. The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the bars was tested in this manner and in no instance could any difference in structure in the three specimens1 be detected. Bars 1 to 3 inclusive are pearlitic in structure. The white areas are ferrite (iron with certain impurities in solution) and the dark areas pearl-

Jan 1, 1915

By Persifor Frazer

It has been the aim of the writer, by measuring his base line on the territory of theoretical chemistry, to attempt to fix by triangula tion certain points within the domain of mineralogy. As the barest first experiment in this direction, a few of the hydrated oxides of iron have been selected, their theoretical construe tion reduced to percentage of the constituents into which the ordinary analytical methods would resolve them, and the results compared with actual analyses compiled from the most reliable sources; the accidental errors being as much as possible eliminated. This method seems to be a simple one and one easily pursued, but, as will shortly appear, it is beset with grave difficulties, all of which the writer does not pretend to have satisfactorily surmounted. In the first place arises the important question, what are we to understand by the hydrated oxides of iron ? In all books of chemistry and lexicons of minerals, the proposition, long ago taught by the earlier chemists, that water might exist in two forms of combination, viz., as water of crystallization or as water of constitution, is tacitly assumed. There is nothing in the principles of the new chemistry which is opposed to this; for (to carry the mind's eye into the process of con struction of the least units into which a definite chemical compound is capable of being divided without losing its characteristic proper ties), however unlikely it may seem, it is, nevertheless, possible that a given molecule of iron may, under certain conditions of heat, pressure, etc., attract to itself as many molecules of the water in which it is natant as: from the relative size, shape, attractive force, etc. of either, it is capable of taking up, and this complex system of associated molecules might oscillate as a physical unit so long as the conditions on which its existence was dependent remained unchanged. Moreover, it is highly probable that the first effect upon such a mole cule produced by physical or chemical forces would be to separate it into two or more simple ones of different kinds, while a further ap plication of these forces might rend asunder the bonds of the simpler compounds themselves.

Jan 1, 1879

By Persifor Frazer

(Read at the Amenia Meeting, October, 1877.) IT has been the aim of the writer, by measuring his base line on the territory of theoretical chemistry, to attempt to fix by triangulation certain points within the domain of mineralogy. As the barest first experiment in this direction, a few of the hydrated oxides of iron have been selected, their theoretical construction reduced to percentage of the constituents into which the ordinary analytical methods would resolve them, and the results compared with actual analyses compiled from the most reliable sources; the accidental errors being as much as possible eliminated. This method seems to be a simple one and one easily pursued, but, as will shortly appear, it is beset with grave difficulties, all of which the writer does not pretend to have satisfactorily surmounted. In the first place arises the important question, what are we to understand by the hydrated oxides of iron ? In all books of chemistry and lexicons of minerals, the proposition, long ago taught by the earlier chemists, that water might exist in two forms of combination, viz., as water of crystallization or as water of constitution, is tacitly assumed. There is nothing in the principles of the new chemistry which is opposed to this ; for (to carry the mind's eye into .the process of construction of the least units into which a definite chemical compound is capable of being divided without losing its characteristic properties), however unlikely it may seem, it is, nevertheless, possible that a given molecule of iron may, under certain conditions of heat, pressure, etc., attract to itself as many molecules of the water in which it is natant as from the relative size, shape, attractive force, etc. of either, it is capable of taking up, and this complex system of associated molecules might oscillate as a physical unit so long as the conditions on which its existence was dependent remained unchanged. Moreover, it is highly probable that the first effect upon such a molecule produced by physical or chemical forces would be to separate it into two or more simple ones of different kinds, while a further application of these forces might rend asunder the bonds of the simpler compounds themselves.

Jan 1, 1878

By E. S. Machlin, A. A. Hendrickson

Use was made of a recently developed surface-accumulation diffusion technique to measure the self-diffusivity of edge-type dislocation singular lines (Burgers vector along <110>) in a bent and polygonized single crystal of silver. Two factors are involved in obtaining a number for the diffusivity. One factor, the dislocation-line density, was measured by a microscopic technique recently developed, and the value of the other parameter, the effective "diameter" of a dislocation pipe, was estimated. With these parameters equal to 7.3 X 106 dislocations per sq cm and 10-7 cm, respectively, it was found that the self-diffusivity along edge-type dislocation lines was a factor of about two times the average grain-boundary self-diffusivity. The dislocation-pipe diffusivity is about 7x10-7 sq cm per sec at 450°C. THE possibility of short-circuit diffusion through imperfections in crystals has been recognized for some time. It was only recently, however, that concerted effort has been expended to obtain values of diffusivity for grain-boundary short circuits. The work, for example, of Hoffman and Turnbull1 on silver, Fisher&apos;s&apos; analysis of the grain-boundary dif-

Jan 1, 1955

By Luther B. Eames

The recovery of dissolved gold from slime pulp in the cyanide process was first accomplished by intermittent decantation. This simple process consists in mixing with the pulp containing the values in solution, a solution of lower gold content, settling the mixture in a tank and decanting the clear supernatant fluid. The thick pulp remaining in the tank is pumped to a second tank together with more barren-solution and again settled and decanted. After several repetitions of this operation, values are so far reduced that further washing is not profitable. The gold recovery of this process is high, but the plant required is bulky, labor cost is high and the amount of solution to be precipitated is excessive. Historical Data As early as 1901, a plant was built in the Black Hills of South Dakota by John Randall, employing the same principles but attempting to make the process continuous by substituting for flat-bottomed tanks, cones which operated continuously, receiving a constant feed and discharging a steady stream of thickened pulp. These cones were operated in series, the thick underflow of the first one forming, with a stream of diluting solution, the feed to the second cone of the series. Barren solution was added to the tank immediately preceding the discharge tank and, after being slightly enriched by the low-grade pulp in this tank, overflowed to form a diluting solution again for the richer feed entering the third tank from the end of the series, and so on back to the richest tank of the series. Clear water was used for the wash in the final tank. This is the principle on which all successful countercurrent decantation plants operate at the present time, but Randall&apos;s plant was not successful because of mechanical difficulties in getting a continuous thick discharge from his cone tanks. A similar plant was built in South Africa although there the washes were not repeatedly used, as in Randall&apos;s case, but were precipitated after each contact with the ore. This also was abandoned

Jan 1, 1918

By Leonard Larson

BEFORE direct or wet smelting of copper concentrate was adopted at the McGill smelter, in November 1932, actual furnace smelting tests had indicated the possibility of smelting between 400 and 500 dry tons of wet concentrate per furnace day. Under calcine smelting practice, solid charge up to 1165 tons per furnace day had been smelted. It was realized that in order to smelt wet tonnage in equivalent amount per furnace day, a higher combustion rate and higher temperatures would be neces-sary within the furnace. The reverberatory furnace considered in the following history of wet-smelting de-velopments is a unit 127 ft. long and 28 ft. 8 in. wide, inside dimensions (Fig. r). This furnace was in operation through all the years from 1934 to date. During 1933, the first complete year of direct or wet smelting, the plant was on a curtailed copper-production basis and the available concentrate tonnage to be smelted was limited. The average coal-firing rate in the reverberatory for that year was 124 tons per furnace day. This rate was lower than the average for years immediately preced-ing under calcine smelting practice. With this coal-firing rate, an average of 391 tons of new metal-bearing material (N.M.B.M.) was smelted per furnace day. The following year, 1934, the coal-firing rate was in-creased to 139 tons and the smelting rate increased to 448 tons N.M.B.M. per fur-nace day. In succeeding years production required that either more tonnage be smelted in the one furnace or an additional furnace be placed in operation. With this situation confronting the smelting depart-ment, it was determined to continue the program of increasing the coal-firing rate and also to intensify the temperature in the smelting zone of the furnace. In order to accomplish this, various improvements were made to aid combustion within the furnace. The burners were enlarged, in-creased primary air was supplied to the burners, and changes were made in the furnace to enlarge and streamline the out-let, thus increasing the furnace draft.

Jan 1, 1940

By Kefton Teague

The minerals discussed in this section have experienced a gradual, although not spectacular, growth in general. Obvious exceptions are the gradual decreasing use of talc and bentonite as filler materials, partly because of availability and relatively lower sales price of competitive materials. Mineral fillers and filter minerals are used principally in those countries that are heavily industrialized. Except for diatomaceous earth of filter grade, most industrialized countries are reasonably self-sufficient in the various filler and filter minerals. Prices of the various mineral commodities during the period 1950-1970 increased approximately as follows: barite, 43%; diatomaceous earth (filler), 49%; diatomaceous earth (filter), 55%; fuller&apos;s earth, 55%; talc. 77%; and bentonite, 94%. Actual usage of these mineral commodities as fillers and filters, during this period, showed changes approximately as follows: (1) Decrease-fuller&apos;s earth, 6%; talc, 15%; and bentonite, 29%. (2) Increase-barite, 113%; diatomaceous earth (filler), 150%; and diatomaceous earth (filter), -194%. A relationship between the amount of the various fillers and filters used and price increases is apparent. For example, barite increased only 43% in price, but its use as a filler has increased by 113%. On the other hand, talc, which increased 77% in price, decreased in filler use by 15%; and bentonite, which increased 94% in price, has decreased for filler and filter purposes by 29%. The actual decrease in the use of some of these commodities is not entirely caused by an increase in price. Competitive materials frequently have made substantial gains in the various filler and filter markets. For example, much of the bentonite used in the late 1940s and early 1950s for clarification of mineral and vegetable oils has been replaced by competitive materials. BARITE Occurrences and Sources In the United States, barite is produced from about 14 states, listed in approximate order of importance as follows: Missouri, Arkansas, Nevada, Georgia, Alaska, Tennessee, Kentucky, California, New Mexico, North Carolina, Washington, Idaho, South Carolina, Texas, and others. During the 20 years ending in 1970, almost equal amounts of barite were produced from Arkansas and Missouri. Within recent years, Nevada has replaced Georgia as the third leading barite--producing state. West Germany is second to the United States in barite production. Other important barite-producing countries include: Mexico, USSR, Italy, Greece, Canada, and Ireland. Ireland has become an important barite producer only recently. Barite is obtained from vein and cavity fill-

Jan 1, 1976

ONE of the perplexing problems that face the translator of an old technical treatise is the question of terms for units of weight and measure. We have used an English word only when it is linguistically equivalent to the Italian one and is a unit of approximately the same size. Libbra and oncia thus become pound and ounce, for the actual weights were within 10 per cent of the modem Troy weights. On, the other hand, the length measures braccio, palmo, and dito, which could be rendered literally as arm, palm, and finger or digit, respectively, have no good English metrological equivalents and it has seemed best to retain the Italian words. The exact transfer of Biringuccio&apos;s weights and measures into modern terms is impossible because of the uncertainty as to his standards. Even as late as 1803, when the metric system was first introduced into Italy, practically every city had its own standards. There were, for example, at least eight different palmi, varying from 22.3 to 29.2 centimeters. The values listed below for the various units mentioned by Biringuccio are the Florentine ones, which were also used in Siena and Tuscany: [ ]

Jan 1, 1942

By James Douglas

American metallurgical inventions have not always been absolute metallurgical improvements, if accurate work be the standard of comparison; but when we review the new methods and machinery which have been generally accepted, we find that some have become essential to the metallurgist the world over, while all are so admirably adapted to the peculiar requirements of our local conditions that they have entirely supplanted foreign processes and appliances. The necessity of diminishing to the utmost the employment of labor (owing to its great cost), and the inexorable requirements of our modern joint-stock corporate system, which demands that large quantities be worked up in order to secure large returns, regardless betimes of waste, have been the impelling motives to invention, and indicate the special directions in which originality has been exercised. As might be anticipated, the West has been the most fertile field of inventions by miners and metallurgists, by reason of its great and varied mineral wealth, locked up in ores sometimes lean and often of intricate composition, which must be profitably handled, at a great distance from fuel and from building-materials, by workmen who are paid wages very much higher than those received by their fellow-workmen of like craft in Europe, and in some localities twice as high as those paid for like services even in the eastern States. Moreover, paradoxical as it may seem, the technical inexperience of many of those engaged in mining and metallurgy has helped rather than hindered the progress of invention; fop while there may have been ignorance, there has been radical freedom from

Jan 1, 1894

By J. D. Testerman

A statistical technique to identify and describe naturally occurring zones in a reservoir and to correlate these zones from well to well is described. The technique is particularly useful in describing a reservoir where cross flow between adjacent strata is important in determining reservoir behavior. Although it has been used primarily for permeability zonation, the technique is general and can be used to correlate any reservoir property or related data, such as the information contained in well logs. INTRODUCTION One of the first problems encountered by the reservoir engineer in predicting or interpreting fluid displacement behavior during secondary recovery processes is that of organizing and using the large amount of data available from core analysis. Permeabilities pose particular problems in organization because they usually vary by more than an order of magnitude between different strata. Due to the sheer volume, it is almost always necessary to group data and to use an average value to represent a number of measurements. Perhaps the most common method now used to group permeability data is the capacity-fraction technique, which ranks permeabilities in order of magnitude, regardless of the physical location of the permeabilities within the reservoir. The cumulative per cent capacity is plotted against cumulative per cent thickness. This plot is divided into an arbitrary number of zones, generally of equal thickness. Five zones (or averaged groups of data) usually are obtained, each of which is treated as homogeneous in subsequent calculations. The division so obtained has no physical meaning; strata in the same zone, calculation-wise, are usually not adjacent in the reservoir. Reservoir engineering techniques being developed will handle crossflow that occurs between adjacent communicating reservoir strata because of imbibition and gravity segregation. Since crossflow occurs between physically adjacent layers within the reservoir, a new zonation technique recognizing the actual location of strata within the reservoir is necessary. Similarly, the recognition of natural zones is important for predictions of oil recovery by processes involving diffusion. One such process is miscible displacement, where predictions of lateral diffusion within the reservoir must recognize the actual location of the invaded zones in relation to the rest of the formation. Natural zones must also be adequately recognized to account for heat transfer within the reservoir during thermal exploitation. Because of the complexity of the problem, statistics appear to offer the only practical hope of dividing a reservoir into physically-meaningful natural zones. This paper presents a statistical technique for identifying these natural zones and for ascertaining which ones are likely to be continuous between adjacent wells. The zones defined have minimum variation of permeability internally and a maximum variation between zones. The technique is general and can thus be applied to reservoir properties other than permeability. The method will guide the reservoir engineer in estimating which zones are likely to be continuous between wells. However, a statistical correlation based on permeabilities in two different wells is no guarantee that the zones so defined are, in fact, continuous. Rather, the assumption of continuity must be consistent with geological data concerning the depositional environment, as well as justified on the basis of engineering judgment in combination with statistics, just as judgment is required with conventional zonation methods. CALCULATION PROCEDURE The reservoir zonation technique is a two-step operation. The steps are individually described, and a sample calculation is presented in the Appendix. ZONATION OF INDIVIDUAL WELLS First, the set of permeability data at a single well is zone, into Zones. These zones are selected so that variation is minimized within the zones and maximized between the zones. The equations4,6 used to zone the data are where B = the variance between zones, , = the number of zones, i = the summation index for the number of zones, j = the Sumation index for the number of data within the zone, mi = the number of data in the ith zone, k,. = the mean of the permeability data in the ith zone, k . = the over-all mean of the data in the well, W = the pooled variance within zones, N = the total number of

LIST OF REFERENCES COMPILED BY ENGINEERING SOCIETIES LIBRARY FUEL POSSIBILITIES IN STEEL MAKING. Iron Age, November 6, 1913, p. 1056-1059. Paper read before the American Iron and Steel Institute, by William Whigham. The author discusses the use of pulverized coal as a fuel for open-hearth furnaces. IMPROVED PULVERIZED FUEL FEED DEVICE. Iron Age, November 6, 1913, p. 1024. Brief description of the Dunn apparatus, especially intended for cement kilns, but used also in the nodulizing of iron ore. WIDER UTILIZATION OF PULVERIZED COAL, H. R. Barnhurst. Iron Age, October 23, 1913, p. 906-908. Part of discussion of paper by James Lord on The Use of Pulverized Fuel in Metallurgical Furnaces, read before the Engineers&apos; Society of Western Pennsylvania. POWDERED COAL FOR OPEN HEARTH FURNACES. Iron Age, October 16, 1913, p. 855. Abstract from the "Coal and Coke Operator." USE OF PULVERIZED COAL AS A FUEL FOR BOILERS, R. C. Carpenter. Sibley Journal of Engineering, December 1913, p. 85. COAL-DUST FIRED BOILER. Indian Engineering, November 29, 1913, p. 301. PROGRESS IN FUEL UTILIZATION. Mining and Scientific Press, October 25, 1913, p. 638. BUFFALO GRAIN-ELEVATOR DUST EXPLOSION. Engineering News, July 31, 1913, p. 223-24. Reprinted in the National Fire Protection Association Quarterly, October, 1913, p. 149-151. Mention is made of the danger of explosions in connection with the burning of powdered coal. POWDERED FUEL AND EXPLOSIONS. Railway Age Gazette, July 18, 1913, p. 53-84. Letter by W. D. Wood. USE OF PULVERIZED COAL IN METALLURGICAL FURNACES, James Lord. Engineers&apos; Society of Western Pennsylvania, Proc., October, 1913, p. 363-371; discussion, p. 371-417. With bibliography.

Jan 3, 1914