Search Documents

By R. F. Krueger

Results are presented from tests of dynamic fluid-loss rates to cores from clay-gel water-base drilling fluids containing different commercial fluid-loss control agents (CMC, polyacrylate or smt,ch), organic viscosity reducers (quebracho and complex metal lignosulfonate) and oil at several different levels of concentration. In the dynamic system the most effective individual additives to the clay-gel drilling fluid, based on cost-equalized concentrutiom, were found to be starch and the viscosity reducers. These results do not conform with the rankings determined by API fluid-loss rests, which indicate CMC, polyacrylate and starch to be the most effective and comparable. Generally, minimum dynamic fluid-losr rates were attained at cost-equalized concentrations of additive (including thinner) of about $1.00/ bbl, or less. For chernically treated clay-gel drilling fluids, both the standard and the high-pressure API filter-loss tests were found to he inaccurate indicators of trends in dynamic fluid-loss rates under the test conditions used, particulurly for drilling muds containing viscosity reducers. From a practical field viewpoint, restrictions on the applicability of the API fluid-loss test are such that it is open to question whether or not results of this test can be used routinely with confidence as an indicator of control of down-hole fluid loss under field treating conditions. INTRODUCTION The petroleum industry spends large sums of money during drilling operations to control the fluid-loss properties of drilling fluids based on the standard API filter-loss test,' which is a static filtration system. Laboratory studies' ' of dynamic filtration have shown that in a given time period filtrate loss from a circulating mud stream is greater than from a static system and that it is a function of linear mud velocity, pressure and the properties of the drilling fluid. Ferguson and Klotz' and Horner, et al," observed that (I) the dynamic fluid-loss rates for the drilling fluids used were not related to the extrapolated API filter loss and (2) the drilling fluids with the lowest API filter losses did not have the lowest dynamic fluid-loss rates. However, there has been no published information on the relative effects on dynamic fluid-loss rate as a given drilling fluid is treated with increasing amounts of chemical additive to reduce the API filter loss. Such information is economically important because drilling-fluid costs rise rapidly as chemical requirements increase. This paper presents the results of a study of dynamic filtratioi rates to cores from a clay-gel water-base drilling fluid treated with various commercial viscosity reducers and chemical fluid-loss control agents. The dynamic fluid-. loss rates to cores are compared with the standard API filter-loss values at several different levels of additive concentration. Dynamic filtration rates were obtained in each experiment under two different simulated wellbore conditions: (1) filtration just above the bit through a new mud cake laid down dynamically on a freshly drilled formation and (2) filtration up-hole through a mud cake formed by deposition of a static filter cake on top of the initial dynamically formed cake. The latter case corresponds to the bottom-hole conditions existing above the bit when mud circulation is restarted after a stand of pipe has been added or a round trip has been made to change the bit. Except for the short-duration, high-rate filtration beneath the bit where no mud cake can form, these two conditions probably represent the two extremes of dynamic filtration. Because thickness of a dynamic mud cake formed on freshly exposed formation is limited by the shearing action of the mud stream, the filtration rate for this condition is high. On the other hand, once circulation is stopped and a static mud cake forms on top of the dynamic cake, re-starting circulation has only a small effect on the cake properties and filtration rate is much lower thereafter. A discussion of the mechanics of mud-cake deposition and dynamic filtration is outside the scope of this paper but may be found in more detail in publications by prior investigators. APPARATUS AND EXPERIMENTAL CONDITIONS The test equipment used to simulate the dynamic flow conditions existing during drilling was a modification of that described previously by Krueger and Vogel: A schematic flow diagram is shown in Fig. 1. In general, a power-driven, high-pressure mud pump capable of delivering up to 60 gallmin was used to circulate drilling fluid parallel to the faces of 1-in. diameter sandstone cores mounted in a 2 3/4-in. ID high-pressure test cell. Pump rates were controlled by means of a magnetic clutch to maintain an average axial fluid velocity of 110 ft/min in the annular space between the cell wall and a 1 1/2-in. rod positioned on the center line of the cell. The core specimens were Berea sandstone plugs sealed with plastic inside 1 1/8-in. OD tubes and were fluid-saturated prior to use. Burettes were used to accumulate fluid discharged from the cores. The mud sump shown was used for treatment and storage of the drilling-fluid samples during a particular test. The valve arrangement permitted either (1) circulating drilling fluid through the by-pass line while treating with

By L. Valentik

Many attempts have been made during the last 40 years to evaluate the performance of gravity separation equipement, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris in 1950. The methods suggested by the Conference were accepted and very widely used in the last two decades. This paper discusses an improved method of evaluation in the light of the now-accepted standard presentation. The float-and-sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve me then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the content is valid and applicable to other types of minerals which are separated by gravity methods. Many attempts had been made during the last forty years to evaluate the performance of heavy-media separation (HMS) equipment, that is, the effectiveness with which floats and sinks are separated.'-' The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris. 6 The primary aim was the thorough understanding of the mechanism of separation and the unified presentation of data on gravity separation so that the evaluation and comparison of washery performance could be made from all over the world. No strict overall standardization has been achieved, but after the conference a more or less uniform presentation of performance was accepted, which, during the last two decades, has been very widely used. In this paper, illustration of the old methods and an improved method of evaluation will be given. HEAVY-MEDIA SEPARATION (HMS) PERFORMANCE CRITERIA In the ideal HMS process, all material lower in density than the specific gravity of separation (SGS) would be recovered as floats and all material of higher density would appear as sinks. In order to evaluate the misplaced material, the washery products are tested at the density at which the washing unit is operated. The original type of plot1,7, 8 is shown in Fig 1; this was developed primarily for coal cleaning units. The curve for raw coal represents the cumulative percentages of sink material. The refuse curve is also plotted as a cumulative sink, the percentages being expressed in terms of raw coal. This diagrammatic representation of the results of washing units has the merit of easy visual observance of the degree of separation obtained. The error areas (cross-hatched) are a measure of the amount of misplaced material and therefore they can be used to characterize the quality of separation. The ideal and actual separating performance between floats and sinks can be best seen from the partition curve developed by Tromp,2 where the ordinate is the percentage recovery of the sinks, and the abscissa is the specific gravity (Fig. 2). It can be seen from the shape of the curve that as the SGS is approached, the proportion of material reporting to the improper product increases rapidly. In fact, the SGS can be defined as the density of the material in the feed that is distributed equally between float-and-sink products. When the upper half of the curve is inverted, a shape similar to that of a Gaussian error distribution curve is obtained and therefore the analysis of gravity separation may be carried out by using the law of probability. The shape of the curve in Fig. 2 is determined partly by the density composition of the feed, and partly by the sharpness with which the unit separates floats from the sinks.9, l0

Jan 1, 1970

By H. R. Drullard

TO obtain the best results from hammer drills, close attention must be paid to two factors in drill maintenance, which are of equal importance; one is lubrication, the other is the shank. With the exception of stoping drills, most modern rock drills require both oil and grease. The oil ports are in the lubricator, on or behind the hammer cylinder; the grease port for the lubrication of the chuck sleeve and rotating mechanism is on the chuck end. Ordinary machine oil is not adapted to rock drills; a heavier more gelatinous oil such as castor machine oil or liquid grease should be used. The lubricators should be filled once for every 12 or 14 ft. (3.5 to 4 m.) of hole drilled. Grease guns should be used to fill the port in the chuck end once a shift; a medium (No. 3) grease is well adapted to this purpose. Hard grease must not be put into the lubricators, as it will not flow through that part. Contrary to the popular belief, oiling a machine once or twice a shift does not provide sufficient lubrication; the drills should be oiled once for every 12 or 14 ft. of hole drilled. The rotating handle of a stoping drill is an oil reservoir and is provided with a port for oiling. The rotating handle is packed with wick-ing, or similar material, which causes the oil to feed slowly from the handle to the other parts of the machine. Stoping drills require oil at least twice a shift; lighter oils than castor, such as Arctic Ammonia, may be used. Drills used in shaft sinking can be oiled satisfactorily by placing a good-sized, drop, sight lubricator on the station above the sinking operations and connecting it with the air-line supplying the sinking drills. If this lubricator is properly filled and adjusted, a uniform oiling of the sinking machines will be effected without the necessity of oiling the drills individually. The grease end should be filled at the station or surface before each drilling period. The shift boss should see that the machines are greased and also that the lubricators at the station function properly. The life of the air-drill hose is somewhat shortened by this method, as oil attacks the inner tube; but as some oil is always present in the compressed air, this is not a serious objection to the method.

Jan 1, 1922

By J. C. Rengel

Why and how the nuclear industry entered the electric power generation business is discussed in terms that nuclear energy was an undoubtedly additional energy resource and that it had promise of becoming a virtually inexhaustible generating power if breeder reactors could be devised. The growth of nuclear power, its total generation capacity, are related to the need of increasing energy requirements. The use of atomic energy for power generation will grow if it can compete economically with other fuels. The rate of growth, the time scale and direction of technical development is dependent on ore supplies. It is predicted that by 1980, 50% of all new power installations will be nuclear stations. INTRODUCTION Ten years ago, the nuclear industry was virtually unborn, the Atomic Energy Act of 1954 had just been signed, and peaceful applications of atomic power was little more than a phrase. Serious discussion of the practical application of nuclear energy to electric utility installations in the West was highly unlikely. The questions: Why and how did the nuclear industry enter the electric power generation business at all?; What is the predicted growth of nuclear power?; What technological changes do we predict?; How will the above changes affect the utilities? will in part be answered by this paper. WHY NUCLEAR POWER? The only justification for the West as for any other section of the country for atomic power is economics. Whatever energy source will provide the lowest generation cost will prevail; the only electric utilities which have shown an interest in nuclear power are those to whom it means lower generation costs. It is true that the Government sponsored the development of this technology long before there was any evidence of better economics; but a Government must take a very long-range view and it is the only type of organization that can afford to look more than twenty or thirty years into the future. The Government looked at projections such as shown in Fig. 1, which shows various rates of energy consumption, and matched these against estimates of fossil fuel resources. This showed that we will exhaust our low-cost fossil fuel supplies within 75 to 100 years and our total known fuel supplies within 150 to 200 years. The decision to invest in nuclear energy rested, therefore, on two arguments: a) It was undoubtedly an additional energy resource; and b) It has promise of becoming a virtually inex-haustable resource if breeder reactors could be devised if, while generating power, the reactors would produce more fissile materials than they consumed. This decision produced an unexpected bonus: nuclear power became competitive with fossil power much earlier than had been expected and, as shown in Fig. 2, forced the coal industry to take a hard look at its own position. I believe that the drop of coal prices shown here is the direct result of the entry of nuclear power into the energy supply business. At this point, it ought to be explained why and under what conditions nuclear power can be cheaper than fossil power. Fossil fuel cost to the utility is composed of two factors: a) Mining; and b) Transportation. As a result, the cost of fossil fuel to the utilities varies from 126, 106 Btu to 306, 106 Btu and higher. Nuclear energy is highly concentrated and the transportation factor becomes insignificant. Today the cost of nuclear fuel to the utility ranges between 156

Jan 1, 1967

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.' The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.'

Jan 1, 1964

By George C. Ference

Sulfur is the 13th most common element in the earth's crust, constituting approximately 0.05% of the total. It occurs naturally in its elemental form, as metallic sulfides, nonmetallic sulfates, and as combined or free sulfur in natural gas, crude oil, and coal. COMMERCIAL SOURCES Most of the sulfur that is consumed is converted into sulfuric acid before use; therefore, it is not necessary to recover sulfur solely in its elemental form. Processes for recovery are peculiar- to the types of reserves being processed. The major commercial processes as well as the general geographic locations where the appropriate reserves occur are listed in the following. It should be noted that the sulfur values may be recovered as the primary product, as a coproduct with other materials, or as a byproduct. Elemental Sulfur 1) Frasch mining is used for subterranean deposits of elemental sulfur around the Gulf Coast areas of the United States and Mexico. Generally, but not exclusively, such deposits are located in salt dome structure. 2) Autoclaving, flotation, or solvent extraction of surface deposits of elemental sulfur is practiced throughout the world. 3) Extraction and conversion of hydrogen sulfide from sour natural gas into elemental sulfur is done principally in Canada, France, and the United States. 4) Conversion of metallic sulfides from pyrites into elemental sulfur is done via the Outokumpu process in Finland. 5) Catalytic cracking and hydrocracking of sulfur-bearing crude oils to produce elemental sulfur is done worldwide. Desulfurization of refined petroleum products also yields elemental sulfur. 6) Recovery of elemental sulfur from sulfur-bearing oil sands (Athabasca tar sands) has been initiated in Canada. 7) As of this writing (1970), a plant has been constructed for the thermal decomposition of gypsum to produce elemental sulfur in the United States. Sulfuric Acid Sulfur values in the form of sulfuric acid are recovered via: 1) Recovery from smelter gases throughout the world. 2) Roasting of pyrites throughout the world with iron sinters as a byproduct. 3) Roasting of anhydrite with cement as a coproduct, primarily in Europe. 4) Processes currently are being developed for recovery of sulfuric acid from combustion gases resulting from the burning of high-sulfur-content fuel. Other Sulfur values also are recovered from waste products which normally occur in highly industrialized areas. Some examples are: coke-oven gases, sludge sulfuric acid, and pickling liquors (ferrous sulfate).

Jan 1, 1976

By Reino Kurppa

The Pyhäsalmi mine of the Outokumpu Co. is located in central Finland (Fig. 1). The deposit was discovered in the autumn of 1958. Construction of the mine was started a year later, and production began on Mar. 1, 1962 (Fig. 2). At present, 750,000 metric tons (mt) of ore and a nearly equal amount of country rock are mined annually. Slightly over one-half million tons of various concentrates are produced per year, of which 85% is pyrite concentrate, 10% zinc concentrate, and 5% copper concentrate. The pyrite concentrate is treated in the company's pyrite smelter,1 yielding elementary sulfur, sulfur dioxide, and iron-oxide cinders, as well as electric power. Thus all the sulfides, totaling 75% of the ore, are of economic value. This is a fact which had a bearing on the development of the stoping method. GEOLOGY The ore is of breccia type containing fragments of country rock of varying sizes. It is coarse-grained pyrite ore containing sphalerite and chalcopyrite as a matrix between the pyrite grains. Only small amounts of pyrrhotite have been observed in certain marginal parts of the orebody. The ore averages 0.85% Cu, 3.0% Zn, 38% S, and 33% Fe. The orebody extends from the surface down to at least 500 m, which is the lowest level from which present information has been obtained. Horizontally, the orebody is 650 m long. It is 75 m wide at its central part, narrowing towards the ends (Fig. 3). At a depth of 115 m, the orebody suddenly narrows down to a thickness of 25 to 30 m. In the northern part of the orebody, the dip is 50° to 70°, but elsewhere it is almost vertical (Fig. 3).

Jan 1, 1969

By John Gross

THE method of measurement of surface on quartz particles was given in a previous paper.1 With such a method the relation of surface produced in crushing quartz can be compared to the work in crushing without recourse to sieve sizing or microscopic measurement. In crushing, the work input must be known with a fair degree of accuracy. With crushers, rolls, ball mills, and similar apparatus the measurement of the work in crushing is subject to possible errors, due to friction in .the transmission as well as in the machine itself. Moreover, relatively large quantities of material must be crushed to get an average figure. In the selection of a method of crushing, simplicity in design and operation was desired and this was most readily obtained by the use of a free-falling body. A description of the apparatus embodying this principle is given herewith. THE CRUSHING DEVICE The apparatus used is shown in Fig. 1 and in cross-section in Fig. 2. The material to be crushed is placed in the crushing chamber C in the steel mortar M. The mortar is 3 in. dia. by 3 in. high. Two mortars are used, one having a crushing chamber 1-in. dia. by 1/2 in. deep, with a capacity of 4 g. of quartz, the other having a crushing chamber 1 ½ in. dia. by 3/4 in. deep, with a capacity of 12 g. of quartz. The position of the mortar is adjusted by means of three centering screws A. The steel plunger P, which fits neatly into the chamber, is placed on top of the material to be crushed. Plungers of different lengths were tried and as they were found to give practically identical results the length adopted was equal to the depth of the chamber.

Jan 1, 1928

By A. D. Hodges

In May, 1850, the first gold from the Comstock lode was discovered in the sands near the Carson river. It had been washed down by natural agencies, through Gold Caflon, from the decomposed rock of the ledge above. Within a few weeks, the precious metal was traced more than three miles in shallow deposits along the bed of the canon, from the river to the Devil's Gate-—a narrow, rocky cleft, notable to the teamsters of a later day chiefly as the place where " Uncle Jimmy Fair" collected high tolls, and could not reduce the rates, because " this was all he had for the education of his poor children." From 1850 to 1857, a fluctuating band of miners, whose number varied from twenty to two hundred, washed the Gold Canon placers with rockers and long-toms, making four to five dollars a day each until the last-named year, when the deposits were in great measure exhausted. The chief settlement of these miners was at Johntown. During only a third of the year was the water-supply sufficient for their work. The remainder of the time they utilized in desultory prospecting of the hills and in occasional forays for supplies among the Mormons in Carson valley. In 1857, the Grosch brothers discovered the Comstock lode at some point, now unknown, in Gold Hill, but their discovery perished with them. Early in 1858, the " Pioneer Quartz Company," having located several of the small surface-veins around Silver City (whose connection with the main lode has never been definitely shown), built an arrastra, and worked some of their ore; but the returns were so small that they soon abandoned this business. The following winter, James Finney and his partners found gold in place in

Jan 1, 1891

By James Norman, E. W. Gieseke

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content. it might be a desirable constituent of glass batches. The use of spodumene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manganese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li20 on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, [t] the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2, 3 The methods described in the second publication3 did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted. STUDY OF METHOD OF FLOTATION SEPARATION Most of the work on concentration of spodumene was done with rock from near King's Mountain, North Carolina. Rock from two

Jan 1, 1940

By Thomas T. Read

The purpose of the following research, as originally planned, was to investigate the influence of temperature upon the plate-amalgamation process. In order to consider the amalgamation process intelligently, it was first necessary to learn the nature of an amalgam. In the performance of this task it was found necessary to consult a large volume of literature and to perform experimental investigations. The conceptions of the nature of amalgams thus obtained have so important a bearing on the amalgamation-process as a whole, as well as upon the possible influences of temperature, that it was advisable to include them in the treatment of the subject. The broader title is therefore used, even though some features of the amalgamation process have been treated very briefly and others entirely omitted, there being nothing new to present regarding them and their development not required for a clear presentation of the matter in hand. I. Historical Introduction. Gold was one of the earliest metals known to man. Occurring in the metallic state, it could be picked up in nuggets or mashed, as gold dust, from the sand and gravel of streams. Interestiag descriptions of the processes employed in early times for the recovery of gold may be found in Pliny's Natural History and in the treatise by Agricola on ores and minerals. But little progress in the treatment of the ores of gold mas possible until efficient crushing machines were devised. This want was supplied by the introduction, about the beginning of the sixteenth century, of the stamp-mill to treat the ores of Saxony. Blanket-strakes, or similar devices, were used to catch the

Jan 1, 1907

By G. A. Vissac

IN the presentation which follows, washability curves, such as are commonly used in making studies preliminary to the cleaning of any coal or to the concentration of any mineral, have been reduced in each instance to a single straight line; thus all the most important characteristics of the coal or mineral are represented in a form more advantageous than that in which such data usually are shown. To obtain consistent results, float-and-sink data must be based on a single definite narrow size range, which may be designated "a coal unit." It will be shown that such units, each embodying a different size range, can be grouped to form what may be termed "a composite coal." A three-dimensional presentation will emerge, which will closely identify the coal, illustrate its characteristics in a new manner and explain many obscure facts. FLOAT-AND-SINK TESTS For the preliminary study of any cleaning or concentration problem, or in the control of any operation, float-and-sink tests must be made. The results of these tests are grouped in tabular form and then illustrated in various systems of curves; but if such a graphic representation is to have the utmost practical value, it must offer at least the following advantages: (I) It must be easier to read than the tabular results, and (2) it must be easy to plot, check and interpolate. The first requirement will be attained by reducing the number of curves to a minimum, and the second by some system of representation that will use only straight lines. Of the many washing curves now in use, only the "recovery curve," often known as the "composite curve "-a somewhat misleading term-will be considered. Any point on the recovery curve will show what percentage of weight of clean coal can be recovered when the mineral is washed at a certain specific gravity. As an example, the tests listed below Fig. I are illustrated in the drawing by a curve obtained by plotting (I) as abscissas the ash content of the coal recovered and (2) as ordinates the corresponding percentage of refuse discarded; but, in general practice, instead of writing down that weight, it is customary to set down its complement, which is the corresponding weight of coal recovered. From this curve can be deduced the information necessary for the solution of most practical problems. NEW FORM OF GRAPHIC PRESENTATION The resemblance of the recovery curve in Fig. I, or, for that matter, the recovery curve obtained in common practice, to a power curve is apparent. The general equation of such a curve is y = axn where n is negative. Taking logarithms: log y = a + n log x. Using a logarithmic scale, the equation of the recovery curve will be Y = A + bX. On this logarithmic basis, the recovery graph will be a straight line, using the same variables as in Fig. I ; namely, the ash con-

Jan 1, 1942

By H. E. Lee, P. C. Feddersen

Greenockite is the only known cadmium mineral of importance. It occurs rather universally, in minor concentrations, as a secondary mineral in sphalerite deposits. The world's cadmium output is obtained through the processing of metallurgical by-products, largely from the treatment of residues from electrolytic zinc, retort zinc and lithopone plants. These sources are supplemented by the processing of fumes from lead and copper smelting operations. The development of modern selective flotation practice in the decade 1920-1930, which permitted the economical mining of complex lead-zinc ores, resulted in significant increases in the quantities of cadmium entering lead smelting systems. Being closely related to zinc as to occurrence, properties and production, most detailed description of cadmium recovery methods are to be found recorded in connection with zinc metallurgy. Other than occasional articles pertaining to particular operational procedures, literature offers but little in the nature of a balanced survey of lead smelter cadmium recovery practices. While many of the basic operations described for the recovery of cadmium from zinc by-products are applicable to the treatment of lead plant products, the inherent problems involved differ widely. In general the cadmium content of related by-products from routine lead smelting operations is present in lower concentrations, exists in a less soluble state and is associated with both a greater quantity and a greater variety of detrimental impurities. To cope with these problems, lead smelter practices are found to follow the general outline: Preparatory Processing 1. Concentration operations 2. Sulphation operations Cadmium Plant Processing 1. Leaching operations 2. Purification operations 3. Sponge precipitation operations 4. Metal recovery operations 5. Refining and casting operations As in the case of related zinc plant operations, cadmium recovery practices at lead smelters are not standardized. They not only vary as to type, but also extent. Depending upon prevailing conditions, lead smelter cadmium operations range from simple concentration campaigns, for the purpose of sufficiently "up-grading" products for shipment elsewhere, to complete processing steps for the production of refined metal. Preparatory Processing The cadmium content of lead smelter receipts is low and, as a rule, proportionate to the zinc content; the usual range of cadmium contained being of the order of 0.01-0.05 pct. Were it not for the low boiling point of cadmium, such small concentrations would, no doubt, be lost in the large tonnages of slag, metal and other smelter end products. However, the ready volatility of cadmium and its compounds at prevailing lead smelting temperatures results in its concentration in fractional portions of fume collected. This collected fume comprises a circulating load within the smelter system. Thus, the cadmium content of blast furnace fume* increases with each successive circulation until an equilibrium value is reached when the sum of the cadmium losses, due to handling and in slag, waste gases and other end products, becomes equal to the intake as ore. With ore receipts averaging, say 0.03 pct cadmium, the concentration value obtainable, through fume circulation in a routine manner, approaches 10-12 pct. In such operations, cadmium concentrations in blast furnace fume of from 3-5 pct are readily .attainable. However, the concentration gain beyond this range, with each additional circulation, is progressively decreased as a result of mounting losses occurring through handling and in end products. Therefore, to avoid excessive cadmium loss and to enhance the ultimate concentration anttainable, it is customary practice to isolate blast furnace fume at some intermediate cadmium content for special concentration procedure. The most common type cadmium concentration "campaign" involves special smelting operations wherein a relatively high portion of blast furnace fume at 3—6 pct cadmium is incorporated into the sinter charge. This type practice is roughly illustrated by the diagram on p. 111. Cadmium fume collected from lead blast furnace operations is not amen-

Jan 1, 1950

By M. T. Hepworth, W. B. Sample

HYDROGEN solubility and linear contraction measurements were made at constant temperature on an alloy of titanium of constant oxygen-to-titanium molal ratio but variable hydrogen content. A cylindrical specimen of titanium (0.25 by 1.6 in.) containing 0.75 at. pct 0 and less than 0.03 at. pct N was cast from a master button of iodide process titanium which had been alloyed with titanium dioxide. Four vacuum fusion analyses, which were made along the length of the cylinder after the hydrogen solubility studies were made, revealed a variation of oxygen content of less than 0.02 at. pct. The specimen was introduced into a quartz furnace tube, annealed and outgassedat 1050"~ for about 1 hr, and then held at 800" * 0.5" for about 30 hr, during which latter time experimental data were taken. The leak rate to the furnace chamber was not sufficient to contaminate the specimen during the run as determined by leak-rate studies and vacuum fusion analyses for oxygen and nitrogen before and after the runs. The furnace chamber was attached to a modified Sieverts apparatus used to introduce measured quantities of purified hydrogen to the specimen. A quartz pushrod transmitted changes in length of the specimen to a Chevenard dilatometer. The push-rod passed through a vacuum grease seal to the dilatometer which amplified motion of the rod by a factor of 319. During hydrogen addition, the pushrod did not contact the specimen. Measured quantities of hydrogen were added to the specimen and equilibrium hydrogen pressures recorded as a function of hydrogen content. The solubility data, which appear in Fig. 1, agree well with a separate investigation made with a different apparatus. The solubility limit of the hcp a phase appears as an abrupt discontinuity in slope at 3.4 at. pct H. The solubility plot has been extended as a dashed line at this discontinuity in order to emphasize the discontinuity. The hydrogen content at which bcc P appears is not clearly defined. An arrow indicates solubility data were taken upon hydrogen addition. Upon reaching the arbitrary maximum hydrogen content of the run, the quartz pushrod was pressed against the specimen in order to record the change in length with hydrogen removal. A pressure of about 100 g per sq cm was required to overcome the friction of the vacuum seal in order to obtain reproducible linear contraction data. The contraction ratio ~2/1", change in length divided by original length, was set equal to zero for the maximum hydrogen content. The relative contraction of the specimen was observed upon removal of hydrogen in the following manner. The system was opened to the pumps for a few seconds and an unknown quantity of hydrogen was removed. The system was then isolated from the pumps by closing a stopcock and allowed to return to equilibrium. When the temperature returned to 800°C, the pressure stabilized, and contraction ceased, measurements of contraction and pressure were made. The hydrogen content of the specimen was then deduced by measuring the equilibrium PIydrogen pressure and referring to the solubility plot. Linear contraction was then plotted against interpolated values of atomic percent hydrogen. The justification for this procedure is the established reversibility of the hydrogen equilibrium.' Uniaxial compression was assumed to have no effect on hydrogen pressure. The isothermal linear contraction data are plotted on Fig. 1. An arrow indicates data were taken upon removal of hydrogen. The solubility limits of the two phase a i /3 region can be identified by discontinuities ill slope of the dilatometric plot at 9.1 and 3.4 at. pct H, agreeing well with other studies.' Dashed extensions of the plots emphasize the discontinuities. Isothermal studies of expansion made upon hydrogen addition gave curves of much smaller slope and less pronounced discontinuities. A uniaxial compressive stress tends to accentuate volume changes in going from the more open bcc phase to the hcp phase.2 Incomplete data on ex-

Jan 1, 1962

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

R. W. Raymond, New York City: From a study of Mr. Johnson's paper, I conclude that his apparatus is simple in construction and operation, and imitates in a revolving machine the movements of hand-shoveling. It does what a man would do in removing sand from the waste-water with a perforated shovel. I am sorry to say that I fear the present condition of the brown-ore mining industry in the East, as long as

Jan 1, 1899

By D. C. Shelton

This paper discusses the metallurgical testing procedures and their applications at the laboratories and mills of Pima Mining Co. The author shows, using discussions and case histories, that routine sampling and evaluation of daily and monthly data can be as valuable as thorough laboratory investigations and mill test work. A great deal of valuable information can be made available this way. This paper discusses laboratory and mill metal-lurgical testing procedures and their applications at Pima Mining Co., located about 25 miles southwest of Tuscon, Ariz. The Company, incorporated in 1951 (the year the orebody was found) in California to operate the Pima mine, is jointly owned by Cyprus Mines Corp., Utah Contruction and Mining Co., and Union Oil Co. Milling started in December 1956. The main Pima orebody is a contact metamorphic vein of copper-bearing hornfels with an average dip of 45° to the south with an east-west strike. The hanging and footwalls are quartzitic pyroclastics (arkosite) containing some sulfides. Barren igneous intrusions are also present. Conglomerates and alluvial wash cover the deposit to a depth averaging about 200 ft. The principal copper mineral is chal-copyrite. Native copper, chalcocite, and minor amounts of chrysocolla and other copper minerals are also present, together with sphalerite and some molybdenite. Generally, it has been noted that the ratio of chalcocite to chalcopyrite is higher in the lower grade ores, while as the grade increases, there are only minor amounts of chalcocite. Open pit mining is employed at Pima, using both trucks and an inclined skiphoist system. A detailed description of Pima Mining Co. operations was presented by Spaulding et all. More recently another orebody to the north and east of the present pit has been discovered and will be placed in operation within a few years. This ore is of a porphyritic rather than a lode nature since values are disseminated in both igneous and metamor- phosed sedimentary rocks. The new orebody is expected to be harder and cleaner than the present deposit. The views expressed in this article are those of the author and do not necessarily reflect those of Pima Mining Co. nor of the profession in general. PlMA MILL The following outline of milling practice is presented to furnish a background for later chapters of this report wherein specific problems will be detailed and analyzed. Run of mine ore is crushed in three stages, using conventional equipment to 85% minus 1/2-in. for feed to two 10 x l6-ft rod mills operating in open circuit. Each rod mill discharge is split between two 10% x 13-ft ball mills in closed circuit with three 20-in. cyclones. In addition, a 7 x 12-ft ball mill with one 20-in. cyclone receives part of the discharge from one of the rod mills. This equipment was manufactured by Allis Chalmers and Equipment Engineers. The cyclone overflows are combined, sampled and, after joining the regrind cyclone overflow, are distributed into 12 10-cell Fagergren 66-in. flotation machines. The primary rougher concentrate produced

Jan 1, 1965

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of IOO per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie- Illinois Steel Corporation. Clairton By-Product Coke Plant And Coal Washer The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1944

By Carl Zapffe

In ten years the manganiferous iron ores of the Cuyuna District have become impor-tant in the iron industry. By Dec. 31, 1923, 4,735,806 tons had been produced. Dur-ing the war, the low-phosphorus black ores were in demand; now the high-phosphorus low,-silica brown ores are favored. It is estimated that the reserves of these ores are ample for some time. A RISE in less than ten years from obscurity into great prominence economically, tersely summarizes the history and status of the Cuyuna manganiferous iron ores. The Cuyuna district produces and ships mostly high-phosphorus iron ore, but the annual production of manganiferous iron ore is increasing rapidly and productions from individual mines are becoming more regular and more dependable as to grades and tonnages. This ore bids fair to become, shortly, the principal product of the district and is responsible for the present economic prominence of this district. The iron ores of the district have been described, by the author and others, in many publications and will not be discussed here. Lately the manganiferous iron ores have been given some attention, but the range and variations of chemical composition of the ores, the principal physical characteristics of the ores and their deposits, the relative importance of the different ores and their possibilities in future developments, and the life of the respective reserves have not been discussed. It is impossible to give all of this information with the positiveness necessary for it to constitute a reliable guide for investment or even for future mine development. Each property and each party presents a special case and deserves critical consideration. We are dealing with special ores and always with a set of new conditions. Sufficient information of a general nature can be given, however, to indicate the reason for and the trend of the presently augmented developments in the district.

Jan 12, 1924