Search Documents

By Walter Rose

Theoretical expressions are presented to describe wetting and non-wetting phase relative premeability relations. These expressions have then been compared with existing published data, the conformance noted being sufficiently good to satisfy the requirements of some engineering use. As a consequence, it may be supposed that relative permeability characteristics of porous media now can be inferred from basic core analysis data, in a manner more convenient (although less direct) than presently available methods of experimental evaluation. INTRODUCTION This paper presents a new approach to the problem of relative permeability evaluation. A classification of published discussions of relative permeability concepts which have appeared in the petroleum literature will show that previously emphasis has been placed on methods of experimental measurement, on the interpretation of the data so obtained with respect to the variable properties of the system, and on theoretical and practical considerations which relate relative permeability to gross fluid behavior in petroleum reservoirs. Essentially, no detailed examination has appeared which treats the fundamental factors controlling the quantitative features of the relative permeability relation*, although cer- tain references can be Cited where a qualitative awareness of their existence and nature is indicated. This condition is explainable in terms of the recognized complexity of the problem, and in order to provide some basis for theoretical development, the general emphasis has been placed in the past on experimental procedures of evaluation, the validity of which, in principle, could be confirmed by the analysis of well and reservoir performance. However, because of the experimental difficulties which have been encountered (notably, difficulties due to the so-called "end effects"), and because of the general unreliability of field performance tests required to study the applicability of the data, relative permeability phenomena continue to be incompletely understood and described.? In this paper is examined the possibility of predicting relative permeabilities entirely from fundamental considerations. In addition, attention is called to certain important factors, previously unemphasized in the published literature, which now can serve as a basis for the eventual experimental confirmation of this and similar theoretical approaches, as well as the experimental solution of the problem in general. Therefore, the analysis presented herein has the dual purpose both of orienting future experimental activity and also of providing an immediate solution for the relative permeability porblem, sufficiently adequate for some engineering use. It will be seen that the conclusions reached are supported by theoretical and intuitive considerations, and they are not contradicted insofar as gross features are concerned by existing concepts and interpretations of published experimental data, except as specifically noted. Darcy's law, expressed simply as: k dp q = k/u dp/dx .......(1) where q is linear rate of flow (assumed horizontal), k is the † The poor comparison usually obtained between laboratory and field gas-oil ratios (c.f.. Fig. 4 of paper by L. E. Elkins) is illustrative of conditions which dimcourage unqualified acceptance of the results of previous studies except as presently useful approximations. In this connection, Evinger and Muskat have discussed in detail the discrepancy observed between field well productivity values and values obtained from the analysis of laboratory flow data.

Jan 1, 1949

By Walter Rose

Theoretical expressions are presented to describe wetting and non-wetting phase relative premeability relations. These expressions have then been compared with existing published data, the conformance noted being sufficiently good to satisfy the requirements of some engineering use. As a consequence, it may be supposed that relative permeability characteristics of porous media now can be inferred from basic core analysis data, in a manner more convenient (although less direct) than presently available methods of experimental evaluation. INTRODUCTION This paper presents a new approach to the problem of relative permeability evaluation. A classification of published discussions of relative permeability concepts which have appeared in the petroleum literature will show that previously emphasis has been placed on methods of experimental measurement, on the interpretation of the data so obtained with respect to the variable properties of the system, and on theoretical and practical considerations which relate relative permeability to gross fluid behavior in petroleum reservoirs. Essentially, no detailed examination has appeared which treats the fundamental factors controlling the quantitative features of the relative permeability relation*, although cer- tain references can be Cited where a qualitative awareness of their existence and nature is indicated. This condition is explainable in terms of the recognized complexity of the problem, and in order to provide some basis for theoretical development, the general emphasis has been placed in the past on experimental procedures of evaluation, the validity of which, in principle, could be confirmed by the analysis of well and reservoir performance. However, because of the experimental difficulties which have been encountered (notably, difficulties due to the so-called "end effects"), and because of the general unreliability of field performance tests required to study the applicability of the data, relative permeability phenomena continue to be incompletely understood and described.? In this paper is examined the possibility of predicting relative permeabilities entirely from fundamental considerations. In addition, attention is called to certain important factors, previously unemphasized in the published literature, which now can serve as a basis for the eventual experimental confirmation of this and similar theoretical approaches, as well as the experimental solution of the problem in general. Therefore, the analysis presented herein has the dual purpose both of orienting future experimental activity and also of providing an immediate solution for the relative permeability porblem, sufficiently adequate for some engineering use. It will be seen that the conclusions reached are supported by theoretical and intuitive considerations, and they are not contradicted insofar as gross features are concerned by existing concepts and interpretations of published experimental data, except as specifically noted. Darcy's law, expressed simply as: k dp q = k/u dp/dx .......(1) where q is linear rate of flow (assumed horizontal), k is the † The poor comparison usually obtained between laboratory and field gas-oil ratios (c.f.. Fig. 4 of paper by L. E. Elkins) is illustrative of conditions which dimcourage unqualified acceptance of the results of previous studies except as presently useful approximations. In this connection, Evinger and Muskat have discussed in detail the discrepancy observed between field well productivity values and values obtained from the analysis of laboratory flow data.

Jan 1, 1949

By Robert V. Pierce

In the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centered upon haulage, hoisting equipment, mill flowsheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materia,ls. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain ore bodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of: manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered ore bodies are moving rapidly from stopes to reduction plants—because it is now possible to develop an ore body and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials of mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining. In some places it has been found economical to change from .one system of stoping to another that more readily allows the application of mechanical muck-handling equipment. Where blocks are worked faster, the cost of materials, time, and labor is cut drastically. This favorable situation allows more manpower to remain on straight breaking and timbering—or straight production mining. Moreover, when blocks are mined faster, more floors can often be mined vertically before the mucking or wheel floor is moved. This results in several direct savings. There are cases where it has been proved that by working a given block faster more area, longitudinally or vertically, could be mined at one time, thus permitting the reduction of development cost. (Fig. I.)

Jan 1, 1943

By Robert V. Pierce

In the last few years, much study has been devoted to increasing stoping efficiency. The reasons for this are shortage of manpower, shorter working hours, operating regulations, and shortages of essential materials. More efficiency in mining methods is needed to offset these adverse factors. In the past, attention has been centered upon haulage, hoisting equipment, mill flowsheets, etc., but recently the spotlight has been focused on the cost of stoping and the cost of handling materia,ls. Scrapers and scraper hoists have thus assumed greater importance. In order to make it possible for certain ore bodies to be mined at a profit, it has been necessary to apply assembly-line practices to the streamlining of mining methods. All cycles of the mining operation must balance, and the sooner broken ore is removed from the working face, the sooner another round can be started. Since the introduction of scraper hoists in metal mines more than thirty years ago, much progress has been made in their design and application. Alert operators are now constantly watching for methods in which to apply scrapers. The saving of: manpower in development work and the changing of mining methods that once employed manual handling of materials are increasing vital wartime tonnages. Essential ores from newly discovered ore bodies are moving rapidly from stopes to reduction plants—because it is now possible to develop an ore body and place it in production with a minimum of manpower and development work. Today, speed is one of the prime essentials of mining. Everywhere, there is a concentrated effort to use experienced miners in breaking rock, in timbering, and in carrying out the various phases of mining that require many months of training. Much effort is being made to mechanize the working places because experienced men naturally prefer to work where the majority of materials are handled mechanically. In line with this policy, many new men are being taught the details of scraper work, because even green men can quickly become acquainted with scrapers and thereby release older heads to perform the more skilled phases of mining. In some places it has been found economical to change from .one system of stoping to another that more readily allows the application of mechanical muck-handling equipment. Where blocks are worked faster, the cost of materials, time, and labor is cut drastically. This favorable situation allows more manpower to remain on straight breaking and timbering—or straight production mining. Moreover, when blocks are mined faster, more floors can often be mined vertically before the mucking or wheel floor is moved. This results in several direct savings. There are cases where it has been proved that by working a given block faster more area, longitudinally or vertically, could be mined at one time, thus permitting the reduction of development cost. (Fig. I.)

Jan 1, 1943

By William B. Plank

THERE are 19 pct fewer undergraduate and graduate mineral engineering students enrolled in the ECPD accredited schools of the United States this year than there were a year ago. The figures are: 8727 this year and 10,674 last year. The entire engineering group in both countries numbers 171,070, as compared with 184,547 last year and 252,250 in 1947-48, the peak year. This is a decrease of 7.3 pct since last year, less than half as much as the decrease in the mineral engineering group. These figures on engineering enrollment for the current year, 195.1-52, in colleges of the United States and Canada were prepared jointly by the U. S. Office of Education and the American Society for Engineering Education. The seriousness of the situation is shown. by the reported demand for 60,000 to 90,000 engineers this year for civilian and defense industries and only 35,800 will graduate next June. Many of the 1952 graduates are subject to Selective Service, having been granted deferments while in college, and ac- [ ]

Jan 1, 1952

By W. R. Shimer, F. O. Kichline

The investigation herein described was carried out for the purpose of studying, both by chemical and metallographical means, the extent of over-oxidation of steel that can be accomplished by excessive overblowing in a Bessemer converter. 111 addition there are appended some results of basic open-hearth and crucible steels. Remarks on Chemical Methods. The test block used was hemispherical in shape, 4.5 in. in diameter and 2 in. thick. Drillings for analysis were obtained by drilling through the entire solid part of the block, carefully avoiding all cracks and blow-holes and mixing these drillings thoroughly. Drillinga were carefully examined for scale and the finest were gone over with a microscope to be sure all scale from whatever source had been removed. Oxygen was determined by the well-known method of Ledebur, modified according to Cushman,1 with, however, the removal of the preheating tube, which was found unnecessary. This method has been found to give concordant results. Blanks run from 0.0003 to 0.0006 g. Duplicate determinations varied not more than 0.001 to 0.003 per cent. It seems to be generally supposed that the hydrogen method gives only that oxygen which is combined with iron. Whether this be true or not, the content of oxygen existing as iron oxide no doubt predominates sufficiently, so that the result obtained is sufficient to indicate whether the steel is over-oxidized or not. We are well aware that the oxides of manganese and chromium, when existing alone, are not reduced by hydrogen at a red heat. To learn of their action in steel the following work was carried out: A sample of ferro-manganese and of ferro-chrome were each exposed

Jan 1, 1914

By L. G. Schulz

THE possibility of using reflected X-rays to produce images of crystals was explored by Barrettl who developed simple experimental procedures for X-ray microscopy and who showed by numerous examples the great range of information that could be made available. In his method characteris radiation is used to produce an image of a limited area of the sample on fine-grained film, this image subsequently being enlarged approximately X100. A somewhat different method will be described here;' white radiation from a fine-focus X-ray tube-"' is used to produce an image of a relatively large area of a single-crystal surface. part of the sample; therefore, white radiation is needed. The resolution in the image formed on the photographic film will depend on the size of the focal spot of the X-ray tube. If the sample is made

Jan 1, 1955

By K. J. Kutz, F. A. Nice

Drilling of the second shaft at Texas Gulf Sulphur Co.'s Cane Creek potash operation southwest of Moab, Utah, is perhaps the largest undertaking ever made by private industry in the field of rotary shaft drilling. The new shaft, known as No. 2, is located within the plant area, about 400 ft northeast of the No. 1 shaft. This location within the pillar of the first shaft allowed utilization of a great deal of in- formation gained prior to and during sinking of the original No. 1 shaft, a conventionally sunk 22-ft diam shaft 2789 ft deep. The No. 2 shaft will be used for auxiliary transportation of men and supplies, and is steel lined with a 48-in. ID casing. The top 825 ft of the shaft is in predominantly red sandstone with interbedded shales. From 825 ft to 2800 ft, which is the top of the salt beds, the rock is mostly limestone with interbeds of anhydrite and shale.

Jan 9, 1968

By Carls Benedicks

It is well known by every one who has had to deal with boiler tubes that these are often seriously affected by a sort of corrosion, occurring as a local pitting, that frequently causes a perforation of the tube in a rather short time. The characteristic appearance of this corrosion is shown in Fig. 1. A very similar corrosion occurs in condenser tubes (Fig. 2).l A study of the microstructure or local chemical composition of the metal (iron 70:30 brass) fails to reveal any cause for this pitting. Of course one might possibly assume the starting point to be some oxide particle, causing an electrolytic local action, but this in no way explains the continued corrosion, progressing even when the assumed oxide particle must have disappeared. By the excellent work done by the Corrosion Research Committee of the Institute of Metals, and communicated, in October, 1923, to the Institution of Engineers and Shipbuilders in Newcastle-on-tyne, stress was laid on the faot that a content of entangled air has a very obnoxious effect. In the following correspondence, Sir George Goodwin stated that "engineers have, for a long time past, regarded air as the big enemy to be fought against in all questions of corrosion'72 and Kenneth Fraser pointed out that the most vital point is "the avoidance or removal of possibly the chief cause of present day corrosion, i. e. entrapped air and gases brought out of solution."3 In their reply, however, the authors state that they had "never for a moment believed that entangled air was responsible for the beginnings of corrosion, and express the opinion that the gradual liberation of air could not account for localized corro~ion."~ On consulting the many textbooks on corrosion, as that

Jan 1, 1925

By Adrian E. Ross

DRILLING through caving formations in diamond drill holes at depths greater than 2000 ft has long been a serious problem. These caving formations are normally passed only by casing the hole or by cementing the hole. Casing the hole is possible only when a resulting smaller hole is acceptable. In as much as only a limited number of reductions are economically practical, cementing is frequently considered the only method suitable for solving these problems. Cementing either by pumping a slurry into the hole or by dropping cylinders containing cement has proved satisfactory on holes under 2000 ft. In holes substantially deeper than 2000 ft these methods are not satisfactory, since during the pumping process cement separates out, whereas cylinders usually break before the bottom of the hole is reached. A new procedure, the injector method, apparently solves these problems.* With this method, cement is lowered in the hole in a cylinder, the cement being

Jan 1, 1952

By AIME AIME

IT IS not necessary to travel hundreds of miles from New York City to see examples of modern mining methods applied in tunnel work. In the various subway jobs, for instance, underground work is done on so large a scale as to justify the oft-quoted remark that here is the world's greatest mining camp. In such cases, however, the size of the excavation makes wholly disproportionate comparison with the haulage drift or adit level of the West. But in West Orange, N. J., Antonio -DiMarco is driving a tunnel from two headings on opposite sides of First Mountain, under contract with the town of West Orange, which is similar in nearly every respect to the type of work that must be done at the mines, and merits description as an example of fast and economical tunnel driving under conditions commonly met with by the mining engineer in more inaccessible parts.

Jan 1, 1931

Experiments on the Rate of Heat Transfer from a Hot Gas' to a Cooler Metallic Surface Members of the American Institute of Mining Engineers will be much interested in the subject of teat transfer from a hot gas to a cooler metallic surface, and although the book on this subject recently published by the Babcock & Wilcox Co., of New York, deals primarily with boilers, it contains a great deal of information which metallurgical engineers will find of great value. The book starts out with an introduction giving some of the current theories regarding this subject; it then describes in detail the experimental apparatus used, and the methods of conducting the experiment's and recording the data. Then follow some account of the determination of radiation losses in jackets and cooler; measurement of metal temperatures; detection and correction of errors; etc., concluding with a discussion of the results and derivation of corrective formula for heat absorption; heat pressure rate and specific heat of gas.

Jan 5, 1916

By AIME AIME

OUR new Director from the 15th District is Robert W. Thomas; of Ray, Ariz., general manager of the Ray Mines division, Kennecott Copper Corp. In electing him to this office his fellow engineers pay tribute to his ability as an engineer and express appreciation for his service to the A.I.M.E. and its Arizona Section. ?Bob? Thomas was born April 1, 1886 at St. James Minn. received his early education in the public schools of Topeka Kans. and was graduted from Topeka High School in 1905. Already he had decided upon mining engineering as a profession. so he entered the mining school of the University of Kanas from which he was graduated with the degree of B.S. in hlining enginrering. While in college he became a Student Associate of the A.I.M.E. After graduation, lution and isolated mining camps wel-e not the most desirable places in w

Jan 1, 1944

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to supply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their usefu1 life; however, the partial redesign

Jan 1, 1951

By R. C. Buehl, J. P. Riott, E. P. Shoub

PILOT-PLANT tests have demonstrated that it is possible to produce low-sulphur sponge iron (0.03 to 0.05 per cent sulphur) as a continuous process in an internally fired rotary kiln from iron ore or mill scale; a solid carbonaceous reducing agent; and dolomite to control the sulphur content. The proportion of dolomite employed is small, so that it does not add materially to the cost of the sponge iron. The entire operation is carried out at temperatures well below the melting point of iron, so that the product is discharged in granular form. Compared with other methods for the production of sponge iron, the rotary-kiln method has the advantage of simplicity and low cost of equipment and; in addition, requires little labor for the operation of the process. The pilot-plant equipment used for this work was sufficiently large to demonstrate that the production of low-sulphur sponge iron in rotary kilns is feasible and that the costs are not excessive for applications in which sponge iron has distinct advantages over competing materials. This report constitutes a part of a program by the Bureau of Mines under a special Congressional appropriation for studying gaseous and solid fuel reduction of iron ores. Numerous articles on various phases of these investigations have appeared in Bureau of Mines publications or technical journals. Other articles are being prepared and will be published in the near future. The present program, which is under the supervision of Dr. R. S. Dean, Assistant Director of the Bureau of Mines, was initiated in .1942. However, a considerable portion of the work was a continuation of previous research performed by the Bureau. Previous investigators1-4 utilizing the rotary kiln for the production of sponge iron did not develop a suitable method for controlling the sulphur content. A review of the literature shows that the sulphur content in the product usually exceeded 0.2 -per cent unless reducing agents with very low sulphur contents were employed. This high sulphur value made the product generally undesirable for use as melting stock in electric or open-hearth furnaces. The production of sponge iron in an internally fired rotary kiln has been described in detail in Bureau of Mines Bulletin 2702; consequently, this article will be confined mostly to new features of the process-that is, means for controlling the sulphur content of the sponge iron. Suitable raw materials include iron ores or mill scale; coal or coke for reducing them, and sized dolomite (-20+100-mesh) as the sulphur-controlling agent. A mixture of the raw materials in granular form is fed into the elevated end of the kiln, which is fired axially from the lower or discharge end. In the reducing zone, which is approximately one third the length of the kiln measured from the dis-

Jan 1, 1946

By Gareth Thomas

The analysis of Kikuchi pattersns of exct ovientalions from single cryslals and paired Kikuchi lines from single and overlapping crystals is shown to be useful and quanlitalve and is applied to Phase transfovnzcitions including ordering, spinodals, mavten-silic, and nuclealion and growth pyocesses. 112 pinciple, the analysis of exacl orientations enables the crystal system and the Bravais lattice of a crystal to he determined. The advantages of the davk-field imaging technigure for detecting vevy small precipitates are also described. ALTHOUGH Kikuchi electron-diffraction patterns were first observed nearly 40 years ago,' little systematic application seems to have been made of them, until fairly recently during electron microscopy, when their usefulness in contrast experimen and for determining exact orientations8'9 has been pointed out. With the availability of gonio-metric specimen tilting stages it has now become possible to make much wider use of diffraction patterns, particularly the Kikuchi pattern, which is the main subject of this paper. The treatment presented here is not exhaustive but it is hoped that it will stimulate more use of Kikuchi patterns during electron-microscopy investigations. The Kikuchi pattern is formed as a result of Bragg diffraction of the inelastically scattered electrons produced during the interaction of the beam and thick specimens, The important feature of these patterns is that they give an accurate representation of the symmetry of the crystal being investigated, so that it is possible to identify crystal systems and even the Bravais lattice. This means that new structures, e.g., formed in phase transformations, may be identified during normal electron microscopy, so that Kikuchi-pattern analyses considerably extend the uses of the electron microscope. Recent work has also shown that dark-field images are more informative than bright-field images, particularly, for observing small precipitates. The second part of this paper discusses some applications and advantages of dark-field imaging in studies of two-phase systems. 1) DIFFRACTION PATTERNS 1.1) Spot Patterns. Electron-diffraction spot patterns have their limitations because of the importance of the form factor on the intensities and shape of the reciprocal lattice points. Because of the extension of these points into relrods, reflections are possible over a large angular range (+5 deg) and the patterns from thin regions can be complicated because second-layer relrods intersect the reflecting sphere. Spot patterns can thus give only an approximate idea of the crystallography unless the foil is tilted into exact orientation. In this case the spot pattern is symmetrical, with equal numbers of spots on the positive and negative zone directions about the origin. Such cases are necessary for structural analyses and have been used recently to determine the crystal structure of the ordered Ta64C phase." Exact orientation means that the plane of the reciprocal lattice lies exactly normal to the incident beam as shown in Fig. 1(b). It should be noted that in exact orientations the angle of reflection is less than the exact Bragg angle 9 so that the reciprocal lattice points lie to the outside of the sphere, Fig. 1(b). This deviation is denoted by the parameter s and in the usual convention4 s is negative for exact orientations and, of course, zero at the exact reflecting position shown in Fig. l(a). In order to avoid secondary reflections from thickness relrods it is advantageous to work in thicker regions of foils. Diffraction from thick regions may also produce Kikuchi patterns and as dis-

Jan 1, 1965

PHILIP L. GILL, New York, N. Y. (written discussion*).There is one feature of the fire-refining of electrolytic copper which I believe should be mentioned when the relation of oxygen content to the "pitch" or "set" of refined copper is under discussion; that is, the segregation of impurities. Variation of "pitch" or "set" is frequently noted in castings of different shapes, cast at the same time from the same furnace, though the oxygen content remains identical. For instance, it is possible to cast two wire-bars in the same shaped molds from the same ladleful of copper, the one 2 in. thick showing a good level set, the other, 4 in. thick, being overpoled. Also, when two bars are cast of the same weight and at the same time from the same furnace, one bar in a copper mold at the proper temperature, the other in a mold that has been allowed to get overheated, the bar in the hot mold will show

Jan 8, 1918

By W. E. C. Eustis

In September last I had my attention called by Mr. R. G. Leckie to a deposit of nickel in the township of Orford, province of Quebec. In many ways it has proved to be a subject of great interest. As this ore is, as far as I can learn, entirely new in mineralogy and metallurgy, it has seemed to me that it would be a matter of interest to the Institute to have laid before it, in a short paper, the peculiarities I have met with in studying it. This deposit of nickel was first described by Dr. T. Sterry Hunt, our President, in the Geology of Canada, 1863, p. 738, in the follow ing terms: " The general diffusion of nickel throughout the magnesian rocks of the Quebec group has been already noticed. It has, however, never been met with in any considerable quantities in these rocks, although workable deposits of its ores may reasonably be looked for

Jan 1, 1879

By Robert R. French

Beneficiation of low-grade nonmetalliferous mineral deposits by electronic color sorting is currently undergoing a period of rapid development. For those deposits in which the specific gravity, strength, soundness, and electric and magnetic properties of the ore and gangue are similar, the possibility of separation by color, reflectivity, or fluorescence offers hope for the utilization of much poorer quality ore than previously thought possible. For those ores in which consistency of color is required or for which a dry process is preferred, the electronic color sorter is particularly adaptable. Tests performed late in 1966 and reported herein are the result of the continued interest in the dry beneficiation of gypsum and the development of higher capacity color sorting machines. The ore used was a discarded fraction that consisted of – 1 ¼ -in, to + 3/8 -in. ore containing 63.1 to 71.4% (average 67.7%) gypsum. This material was contaminated by various amounts of both carbonate rock and shale, but no pretreatment was performed other than screening to closer size limits before electronic color sorting.

Jan 4, 1969

By R. Maddin, R. Pond

THERE have been many recent studies of nonequi-librium alloy structures using specimens which have been formed by rapid solidification.' The general methods for achieving nonequilibrium structure utilize high velocity impingement of a liquid metallic droplet(s) and one or more substrates of relatively high heat conductivity. Specimens formed by current popular techniques are small and have various forms of irregular geometry which severely limit their use for many measurements of physical or mechanical properties. As a result of geometric limitations most research has been restricted to X-ray diffraction, electron microscopy, and to a small degree, electrical resistivity. Recently several attempts in mechanical property evaluation have been reported.2,3 A technique for casting large quantities of regular, rectilinear, continuous metallic fibers has existed for a number of years.4 We have utilized this technique with some slight modifications to produce nonequi- librium alloy structures. The apparatus is composed of a small open tube furnace, a pneumatic cage which raises and lowers a graphite ejection mold, and a

Jan 1, 1970