Search Documents

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion-equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control. For the present purpose a number of factors important to efficient heat liberation and recovery have been grouped as follows: 1—combustion, temperatures, and rates of heat liberation; 2—radiation, convection, and furnace and boiler configuration; 3—sponge ash, slag, and hard-bonded deposits; 4— low-temperature deposits and corrosion (cooling flue gas below dew point and air-pollution control); 5—the limitations of coal cleaning and boiler size and cost as related to fuel characteristics; 6—future possibilities and conclusions. The development of combustion apparatus for power boilers is progressing at a lively pace. There has been no letup in improvements in design of pulverized-coal-fired boilers, and there is a strong trend at present toward improving dry-bottom units. Spreader stokers with overfire jets and dust collectors as standard equipment are gaining favor. Less than 10 years in commercial use, cyclone burners are going into numerous installations here' and abroad.' Underfeed and traveling-grate stokers have long since been developed for heavy-duty operation, yet new developments in overfire jets and humidification of air blast have improved their performance. A water-cooled vibrating-grate stoker of German origin is being introduced into the United States and Canada." The primary objectives of an ideal coal combustion device are: capacity to burn the variety and sizes of coals likely to be economically available during the life of the unit; capacity to burn the coals automatically for a wide load range and rapid load fluctuations and to burn the coals completely to CO2, H2O, and SO2, which means without smoke and cinders, or carbon in the refuse; capacity to control and discharge all the ash in final granular form without ash adhesion to walls or tubes, and without flue dust; minimum furnace volume; minimum labor and maintenance; low initial and operating cost. Regardless of the method of burning, the gaseous products of coal combustion are N2, CO2, O2, H20, and SO?. By way of illustration, the coal analyses in Table I is assumed from an installation described by E. McCarthy.' When coal is burned with 20 pct excess air (theoretical air, 9.23 lb per lb of coal), the quantities of combustion gas shown in Table II are produced. In addition, the gases carry particles of fly ash, unconsumed cinders, soot particles, and small but significant amounts of vaporized oxides and sulphates of sodium, potassium, lithium, phosghorous, iron, and other metals. In recent years, germanium, one of the rare metals found in coal, has been shown to oxidize and vaporize at combustion temperatures and to be concentrated by reconden-sation at lower temperatures." Pulverized coal and cyclone flames" have peak temperatures of 3000' to 3500°F. Temperatures in fuel beds of large underfeed stokers reach maxima of 3000°F, sufficient to fuse almost any ash and to volatilize some of it. These peak temperatures are above the optimum necessary for rapid combustion, but they hasten heat transfer for ignition as well as boiler heat absorption. Furnace and gas temperatures increase with combustion air preheat. Low excess air has the same effect. Fine coal pulverization and highly turbulent combustion shorten the distance for fuel burnout, increase flame temperature, and speed up heat transfer. Rates of combustion of pulverized coal exceeding 200,000 Btu per cu ft per hr have been demonstrated in atmospheric gas-turbine combusters,

Jan 1, 1955

By Henry Louis

Henry Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).—In this paper Mr. Simons derives the various forms of revolving slime tables, of which the Harz and the Linkenbach tables are typical examples, from the old rectangular or box buddle. This I believe to be an error, at any rate if Mr. Simons attaches the same meaning as I do to the ((evolution" of a dressing appliance. By the '(evolution" of such an appliance I understand the progressive development and improvement of an appliance acting on a definite principle, such improvements having usually for their object the economy of labor in working the same, or the increase of its capacity; when an entirely new principle is introduced, I no longer look upon this as evolution from the old type, but as the origination of an independent type of appliance. The box buddle was no doubt the predecessor of the old Cornish round buddle, which was evolved from it with the object of saving the labor required to work the box buddle; both machines are horizontal-current separators, in which the separation of sands of different densities is effected by their differential rates of fall in a horizontal current of water of considerable depth. These appliances, though well suited to sands, are for obvious reasons not adapted to the treatment of slimes. The revolving tables of the Harz and similar types, on the other hand, act on the principle which I have called separation in thin films of water, and which Mr. Simons calls the film sizing principle, in which the resistance of the surface over which the pulp flows plays an essential part in determining the separation of the particles, and which is well suited to the treatment of slimes. Unlike the last principle, it will not work in deep bodies of water and cannot be used where considerable depth of material accumulates in the appliance, as in the box buddle and round buddle. As I have shown in my book, The Dressing of Minerals, p. 326, these revolving tables are a development of the appliance known variously as the flat buddle, flat table, or frame, the last name, which is the old Cornish one, being the one that I personally prefer. These primitive appliances, as well as the continuous-acting round tables described by Mr. Simons (his Figs. 10 et seq.) all work on the principle of separation in thin films, and are all adapted for the treatment of slimes; his buddles and round tables (Figs. 1 to 9) do not work upon this principle, and should therefore be sharply differentiated from the former. The evolution in each case of the continuous acting, more or less automatic, circular appliance from the primitive, intermittent, hand-worked, rectangular appliance has proceeded upon strictly parallel lines. The question of the evolution of the respective types involves a point of some importance as regards the principles of ore dressing.

Jan 1, 1915

By Gregory M. Dexter

Recent litigation in Pennsylvania between three coal-mining companies and a private water company resulted in the payment by the coal companies of the equivalent of about $500,000 to buy a new water supply to replace that which had been damaged by acid drainage from strip mining. An investigation of the relevant facts indicates that the water could have been treated by spending about $40,000 on equipment and $15,000 yearly for chemicals, labor, and power until the contarnination could be reduced about 80 pct. The water company's supply, furthermore, had deteriorated largely by reason of dry weather before stripping was begun by the coal companies. Payment to the water company should not have exceeded $300,000 and could have been as low as $100,000. Strip mining of coal is common in Pennsylvania. The most important objection to it in Pennsylvania is generally acid pollution of runoff water. An outline of the methods, therefore, that could be used to reduce such pollution, to compare acid-contaminated waters. and to treat such waters to make them satisfactory for public and industrial use is worth-while. The watershed of the West Penn Water Co. covers about 4.5 square miles, 20 miles west of Pittsburgh, and has two 90,000,000 gal reservoirs supplying about 1,300,000 gal daily for public and industrial use of which 450,000 gal daily are for two railroads. The pollution arises from weathered derivatives of typical'" Coal Measures"' rocks, the principal source being pyrite (and marcasite) in Pittsburgh and Rooster coals. Springs and seeps on hillsides issue from sandstone and limestone formations intersecting shale or clay land surfaces, or from perched water tables. The two reservoirs create an artificial permanent water table. Soap-hardness tests on three seepage samples taken in a dry summer ranged from 150 to 500 ppm. Water sampled came from aquifers above Pittsburgh and Rooster coals, obviating the possibility of contact with pyrite-containing coal. Since acid contamination of mine waters is the result of chemical reactions of oxygen and water with pyrite, it will be reduced by the exclusion of either air or water. The Sunnyhill Coal Co. has applied this principle in its "contouring" method of strip mining by burying contaminated coal-waste material under a compact, smoothed-up surface of top-soil, gravel, clay, and sand at a cost

Jan 1, 1950

By I. A. Goddard

INTRODUCTION This paper deals with the development of the sublevel open stoping (SLOS) method in lead orebodies at the Isa Mine of Mount Isa Mines Limited, during the last ten years. Open stoping in different forms has been used at the Isa Mine for many years. Prior to the period under review, stopes were small, pillars were not always recovered, and scrapers extracted the ore. By the end of the sixties, the use of load-haul-dump units was becoming more widespread. Wagner ST5's were the mucking units for the lead cut and fill stopes. Some of the open stopes in 5 orebody above 13 level had 100 kW slushers, but the more southerly stopes were the sites for the introduction of diesel front-end loaders for extraction. In the early seventies, new methods were used in the block of six stopes in 2 and 5 orebodies between 8 level and 13 level and a trial stoping project was undertaken in 7 orebody between 11 level and 13 level to determine possible stope dimensions for the extraction of the Racecourse orebodies below 13 level. By the mid-19701s, stoping was well underway in 5, 7 and 8 orebodies between 13 level and 15 level, using the 'triplet' system, incorporating cemented hydraulic fill to allow greater pillar recovery. As the eighties were entered, development of the Racecourse orebodies below 15 level commenced, as did preparations for 1 orebody in the upper levels of the north end of the mine. In both cases, the pillar recovery method has been changed to reduce the amount of cemented fill required for pillar recovery. GEOLOGY Most of the lead orebodies at Isa Mine lie chiefly to the north of the central shaft complex. They are bedded sulphide deposits in a host rock called Urquhart Shale, which dips at roughly 650 to the west. The main minerals are galena and sphalerite, with the silver mineral, freibergite, being contained in the galena. To the hangingwall of the sequence are the Black Star orebodies (1, 2 and 5) which are relatively wide, pyritic and with low to above average grade lead. The Racecourse orebodies (6 to 16) lie to the footwall, and have a large variation in width, low to high grade lead, and gradation in the lead to zinc ratio from north to south. Stope outlines are often determined by economic or engineering considerations rather than geological. The published extraction reserves are 56 million tonnes of primary ore, containing 150 grams of silver per tonne, 6.4% lead and 6.5% zinc. Traditionally, it has been regarded as lead ore, although the dominant revenue earner varies from time to time. In the Black Star orebodies, the ore and hangingwalls are more competent and open stoping has long been used. The major Racecourse orebodies which have been open stoped are 7 and 8 orebodies. This has been where the orebodies are wider (to the south) and where hangingwall conditions allow. This latter aspect has been greatly influenced by the presence of 'silica dolomite1. This tough, relatively homogeneous, non-bedded rock is, in fact, the host rock for the copper mineralisation at Mount Isa, and provides a competent hangingwall for some of the lead stopes. While the shale's bedding and jointing has a major influence on the ground conditions, there is a major fault system which causes local problems. The principal virgin stress direction is perpendicular to the bedding, but the local stress situation is complicated because of shielding by filled stopes in the hangingwall copper orebodies and because of the interaction between orebodies being extracted to the footwall. Most development on strike is mined with a 'shanty-back’, with the back being as close to normal to the bedding as possible. This is near parallel to most jointing and the principal stress direction. Figure 1 is a plan view of 14 level north, which provides a representative horizontal section through the orebodies. A typical cross section is shown in Figure 2. The narrow, parallel footwall orebodies can be seen to differ from the wider hangingwall orebodies.

Jan 1, 1981

By David A. Keys

The actual procedure in estimating depth of overburden from magnetic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anomalies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1"4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision. The correctness of the theoretical calculations may be checked in two ways. The first is to make laboratory models of various known shapes and pole distributions, to calculate the anomalies to be expected

Jan 1, 1940

By David A. Keys

The actual procedure in estimating depth of overburden from magnetic observations made on the surface will vary with the form of the deposit and any theoretical discussion will apply only so far as the form of the deposit conforms to the mathematical premises on which the theory is based. Since the shapes of natural deposits in the field cannot be expressed rigorously in mathematical form, the best that can be done is to assume some simple form and deduce results. Fortunately many small variations in form produce only slight changes in the estimated depth of overburden, therefore the methods have a definite practical value. For the theoretical treatment, magnetic ore deposits may be divided roughly into three classes, depending upon whether the magnetic anomalies may be considered to arise from (1) a single magnetic pole, (2) a dike or (3) a magnetic doublet. Particular cases, falling under one or other of these classes, have been discussed by different authors.1"4 In general, it may be stated that when the magnetic effects as measured on the surface are due only to one pole of the body, the other pole being so remote that its effect may be neglected, the resultant anomaly F at any point will vary as the inverse square of the distance r of the point from the pole, which may be expressed mathematically by F = k/r2, where k is a constant. When the deposit occurs in the form of a long, thin dike, the resultant anomaly will be of the form F = k'/r and when the deposit is in the shape of a lens, so that both poles have an appreciable effect on the surface, the result will be similar to that caused by a magnetic doublet, and the form will be F = k'/r3. The particular class under which a deposit falls may be deduced from the results of the magnetic survey. The second class is readily found, but there may be difficulty in deciding between the first and third. Isody-namic contours of both the vertical and horizontal anomalies will often be a good guide in making a correct decision. The correctness of the theoretical calculations may be checked in two ways. The first is to make laboratory models of various known shapes and pole distributions, to calculate the anomalies to be expected

Jan 1, 1940

Alfred Stansfield, Montreal, Canada:—In Professor Howe's paper on the position of Ae3, he shows its industrial importance in determining the temperature to which steel should be heated for " grain refining." Several years ago I carried out a research on the " burning " of steel and found that while hypo-eutectoid steel should be heated to Ae3, hyper-eutectoid steel that has been very much overheated must be reheated to the curve Sa on the carbon-iron diagram, in order to redissolve the pro-eutectoid cementite and thus to obtain recrystallization and grain-refining. This treatment was necessarily only partly successful, and I should like to ask whether the conditions of heat treatment for refining overheated high-carbon steels have been ascertained. Speaking of the &'Persistence of Solidificational Segregation " Professor Howe quotes an experiment made by Mr. Stead in which a bar of 1.2 per cent. carbon steel was immersed in a large mass of molten blast-furnace slag and allowed to cool with it. The steel was heated ; above the solidus (curve An on the carbon-iron diagram), but below the liquidus (curve AB). A drop of eutectic carbon-iron alloy, rich in carbon, had liquated out and hung below the bar. This agrees exactly with my own observations on the burning of steel, but my interpretation differs somewhat from that of Professor Howe. Professor Howe considers that the fusion of a part of the metal (rich in carbon) shows that the solidificational irregularities of composition had persisted through the rolling and heat treatment of the steel, as otherwise no part of the steel would have been sufficiently fusible to melt. It does not appear to me that such an explanation is necessary. A piece of steel represented in temperature and composition by any point within the area ABa will ultimately resolve itself into a solid phase and a liquid phase in equilibrium with each other. It may appear that if the steel were absolutely uniform no fusion could take place, but, the smallest nucleus of high-carbon, fusible alloy would ultimately bring about this separation into liquid and solid phases, by diffusion of the carbon from the solid to the liquid areas. A nucleus sufficient for the purpose might be provided by an area of pro-eutectoid cementite which had not become diffused during the

Jan 1, 1914

By Ta M. Li

This article draws freely on the experiences of the engineering and operating staff of P.T. Inco and its parent firm Inco Ltd. In addition, information was derived from papers presented during the recent International Laterite Symposium, held in conjunction with the 1979 AIME Annual Meeting, New Orleans, La., February 19-21. The author wishes to acknowledge all contributors and, in particular, Roy Aitken, president and managing director, P. T. Inco.

Jan 7, 1979

By James E. Mills

In the work of exploring certain gold-bearing gravels in the American Valley, Plumas Co., California, entrusted to my charge by Prof. A. Agassiz, of Cambridge, and Q. A. Shaw, Esq., of Boston, it became necessary to sink a shaft through loose materials containing in some layers large quantities of water, and I have been compelled to devise a new method which has proved successful and may be of service elsewhere.

Jan 1, 1885

By David R. Maneval, W. E. Foreman, J. Richard Lucas

INTRODUCTION The objective of this chapter is to inform the industry, as well as the public, of the challenges in dealing with the problems associated with the contamination of air and water from coal preparation plants. The need for an informed industry is most important. It is hoped that some contribution may be given to a more efficient and economical approach to the problems of plant waste contaminants at individual plants. The problem has many facets, and consideration to specific area should begin early before any significant problems develop at a given plant. It is then possible to have a reasoned approach before the pressures of an emergency environment force hasty and incomplete solutions. It will be necessary to anticipate these problems in the design of new preparation plants and advance consideration should be given to all the problems concerned with contaminants. The first part of the chapter will concern itself mainly with the contamination aspects of fine-coal cleaning and "black-water" disposal. Also attention will be given to the nature and formation of water from coal-mine drainage systems and the treatment of these waters for industrial use. Some attention will be devoted to the cost of installing and operating the various beneficiation systems for the removal of suspended solids. The second part of the chapter will analyze the problems of air contaminants from coal preparation plants. The nature and the effects of these contaminants and their potential for air pollution will be examined. One of the most critical is the measurement and analysis of these contaminants. As a result of identifying and determining the extent of the problem, better control can be planned. One of the most serious contaminants in air involves the element sulfur, and its elimination as a source of air pollution is one of the most challenging areas in coal preparation today. The last part of the chapter will emphasize the long-range problem of refuse disposal and control. Minimum operating and maintenance costs are functions of the proper selection and geometry of refuse disposal areas. Disposal procedures are varied but must be rigidly pursued or difficulties will result. Maintenance of refuse areas, including monitoring of burning refuse, is critical. It should be recognized that fine-solid refuse disposal systems must be carefully designed to minimize contamination. WATER CONTAMINANTS FROM PREPARATION PLANTS Pollution Aspects of Fine-Coal Cleaning and "Black-Water" Disposal The effluents from coal washeries and waters draining from plant-site surfaces inevitably contain fine coal and coal refuse materials in suspen-

Jan 1, 1968

By John C. Smock

The fire-clays of New Jersey belong in two geological ages, the cretaceous and quaternary, or post-tertiary. Three very small deposits of plastic clays have been discovered within the limits of the Archæan rocks. These are not refractory and of little importance, excepting in a geological consideration. They have resulted from a decomposition of the feldspars of the rock in situ, and they have been classified as inferior kaolins.

Jan 1, 1879

By C. F. Gates, H. J. Ramey

Recent literature shows that pronounced increases in oil recovery can result from the use of miscible systems in recovery operations. This literature also points out certain problems associated with maintaining miscibility, e.g., compositional changes resulting from alterations in pressure and temperature or from zone dilution. The purpose of the work described in this paper was to study miscible zones for possible use in waterflooding operations and examine the manner in which these zones break down. The fluid system selected for study was oil—terNary-butyl alcohol—water, which, because of its narrow range of miscibility, is ideally suited for investigation in short, linear systems. The laboratory-observed effects on oil recovery and zone stability of a number of variables are reported. Among the variables investigated were miscible zone size, viscosity ratio, length of travel, and interstitial water saturation. Results obtained with this system show that interstitial water adversely affects recoveries because of premature phase break. Salinity of the water further aggravates Ais situation. This effect, although pronounced for this system, would probably occur in any fluid system containing an alcohol. As expected, viscosity ratio has a decided influence on recovery efficiency and zone stability. The results also show that use of a suficieno zone size, even though the system has poor phase characteristics, yields higher oil recoveries than are obtained from straight water floods. Length-of-travel studies showed a square root relationship between zone growth and path length for favorable viscosity ratios. No such clear-cut dependence was observed under unfavorable viscosity conditions. INTRODUCTION As new oil reserves have become increasingly more difficult and expensive to find and develop, the oil industry has devoted more and more time and money to finding more efficient methods for exploiting known reserves. The increasing number of water floods is one manifestation of this attempt to improve oil recoveries from existing fields. Since considerable quantities of oil are by-passed by the waterflood process, it is only a partial answer to the problem. The search continues. Of late, several proposed processes have received the critical attention of investigators. Among them are gas drives, in situ thermal reactions and miscible displacements. The present paper is concerned with miscible displacements in conjunction with water floods. Recent literature1- reports that, under proper conditions, oil recoveries from LPG floods, propane sweeps, condensing gas drives, etc., approach 100 per cent of the oil in place in the region contacted by the flood. This literature also points out some of the problems associated with these processes, one of the main ones being the maintaining of miscibility. Compositional changes resulting from pressure and temperature variations or from zone dilution give rise to phase breaks and loss of miscibility, the conclusion being that, after loss of miscibility, much of the beneficial influence of the zone is lost.' The results of the subject work show that, if sufficient zone material exists ahead of a phase interface, considerable improvement in oil recovery can be obtained. In order to increase our understanding of the behavior of miscible systems as they degenerate into immiscible processes, a laboratory system having rapid deterioration characteristics was needed. The fluid system oil—ter tiary-butyl alcohol (TBA)—water possesses these properties and was the system investigated. Although these fluids are different from those generally employed in miscible studies, an understanding of their behavior can be applied to other miscible slug processes. However, under conditions where mass transfer maintains a miscible system through multiple contacts, e.g., enriched gas drive or high pressure gas drive, the observed behavior of alcohol zones would not be applicable. The variables of interest were zone size, viscosity ratio, length of travel, initial water saturation, rate and core characteristics. Of these, only the effects of the following on zone breakdown and oil recovery are reported in detail: (1) zone size, (2) path length, and (3) initial water saturation. The effects of viscosity ratio and core characteristics are discussed in conjunction with other variables. Although initial water saturation is not envisioned as important to the phase behavior of hydrocarbon systems, e.g., LPG, it is important in alcohol systems. The properties of the fluids and cores used are given in Table 1. As previously stated, this fluid system was selected because of the limited range of miscibility

By Sterry Hunt

The American Institute of Mining Engineers, and American science in general, have sustained a great loss in the death of Prof Benjamin Silliman, deceased at New Haven, Connecticut, on the 14th of January, 1885, at the age of sixty-eight. But a month has passed since, as one of the pall-bearers, I paid the last tribute to the remains of my old friend and honored master.

Jan 1, 1885

By W. R. Shimer

(New York Meeting, October, 1913.) THE investigation herein described was carried out for the purpose of studying, both by chemical and metal-lographical means, the extent of over-oxidation of steel that can be accomplished by excessive over-blowing in a Bessemer converter. In addition there are appended some results of basic. open hearth and crucible steels. Remarks on Chemical Methods. The test block used was hemispherical in shape, 4.5 in, in diameter and 2 in. thick. Drillings for analysis were obtained by drilling through the entire solid part of the. block, carefully avoiding all cracks anti blow-holes and mixing these drillings thoroughly. Drillings were carefully examined for scale and the finest were gone over with a microscope to be sure all scale from whatever source had been. removed. Oxygen was determined by the well-known method of Ledebur, modified according to Cushman,1 with, however, the removal of the preheating tube, which was found unnecessary. This method has been found to give concordant results. Blanks run from 0.0003 to 0.0006 g. Duplicate determinations varied not more than 0.001 to 0.003 per cent. It seems to be generally supposed that the hydrogen method gives only that oxygen which is combined with iron. Whether this be true or not, the content of oxygen existing as iron oxide no doubt predominates sufficiently, so that the result obtained is sufficient to indicate whether the steel is over-oxidized or not.

Jan 9, 1913

By Homer G. Turner

Coals, other than anthracite, have been so thoroughly studied under the microscope during recent years, that we now know what kinds of plants and what parts of plants form the bulk of lower rank coals from peat to bituminous coal. The microscope has also shown the state of preservation of such vegetation as well as the nature and distribution of products of plant decay. These and further details have been ascertained mainly through the employment of two methods of attack, section cutting and maceration. Anthracite has failed to respond to these methods, so well adapted to the study of lower rank coals and, therefore, has been neglected by investigators to such an extent that there is much doubt as to its microscopical characteristics. The object of this paper is to lift anthracite from its realm of obscurity by demonstrating the wealth of microscopical detail that is revealed when reflected light is used on a properly polished and etched surface and, further, to show the relationship between anthracite and bituminous coal. Technique The method adopted in this investigation is similar to that described in an earlier paper.' Because of slight modifications recently made, the process is again described. It consists, briefly, of etching a polished surface of coal with heat. Although pieces of various sizes and shapes are used, blocks of coal about 2 or 3 cm. square take the most uniform polish and are large enough to be handled with ease. Larger pieces can be used if one has the equipment for polishing them and they rnay be desirable when one wishes to study some particular form that extends for some distance through the coal. Large surfaces, however, require greater care in polishing and etching; for this reason, they are not recommended for ordinary work.

Jan 1, 1925

By R. H. Wightman, G. H. Adams

In order to secure good results in the prevention of accidents, it is generally recognized that the desire for such accomplishment, as well as the aggressive and constructive action to achieve it, must emanate from the Top Management and permeate successively down through the "Chart of Authority" to the workmen. Several years ago, with the above as a basis and with full support of the Top Management, the Mining Department started a program of selling the foremen and bosses the idea that safety could be achieved and that it was desired and required. Using psychology, persistence and numerous other methods, the foremen and bosses were finally impressed with the idea that "It can be done" and "It will be done." With this in mind, new ideas were brought forth by the foremen and bosses regarding the caving operation and the specific jobs in the operation. These new ideas were taken up in round-table discussions and resulted in certain changes in the undercutting method and the actual drawing of the blocks. These changes resulted in increasing fragmentation of the blocks which prevented the usual hang-up areas in the blocks. With the rock smaller in size and within reasonable reach from the tapping drifts, accidents were prevented in the tapping section. At the same time, an enforced campaign of housekeeping throughout the mine was undertaken with very beneficial results. The foremen and bosses then, in turn, educated and trained the workers themselves to become safety conscious. In so doing, a constant reminder was given on all jobs assigned that the job was to be done safely as well as efficiently. No man is assigned a job who is not qualified for the type of work required. Efficiency and safety go hand in hand. Safety Rules To supplement and aid this safety conscious attitude, certain safety rules applicable to our operation, a modified block caving system of mining limestone, in addition to the established state regulations, were put into effect and enforced. The specific rules referred to above and which will be mentioned below are in most cases simply a means of applying and complying with the very adequate "Mine Safety Orders" issued by the Industrial Accident Commission of the State of California. Some of the safety rules and policies are as follows: All men are required to wear safety

Jan 1, 1950

1. Healthy and active Local Section organizations are vital factors in promoting the vigor and growth of the Institute. 2. Activity on the part of Local Sections should be recognized and stim¬ulated by appropriation of funds from the Institute's treasury; and these appropriations should be as large as is consistent with the relative needs for other activities. 3. As between different Sections, the amount of such appropriations should be based primarily on the extent of activities as reflected in the number and character of meetings .held and the attendance of the members at such meetings. 4. In making a request for funds for any year, the officers of a Local. Section should submit: (a) a report showing in reasonable detail its income, and expenditures for the preceding calendar year; (b) a statement of the number of. members to whom announcements of each meeting had .been mailed; (c) a record of meetings held, the character of the program, and _ attendance of members at each; and (d) any further facts having a bear¬ing on its financial requirements for the coming year.

Jan 1, 1937

By Richard Moldenke

The author discusses some economic conditions which have made the career of the cast-iron pipe industry in the United States a checkered one. He next describes the two new developements in the manufacture of cast-iron pipe-both along the lines of centrifugal casting. The advantages and disadvantages of both processes are presented in some detail. Finally, statistics on the production of pipe in the United States at the present time are given, as well as the plants-and their capacities-so far as these are situated in the South. No SINGLE branch of the foundry industry has been brought to a production basis of huge tonnage, low manufacturing cost, and producing material of a remarkably high quality, as has the making of cast-iron pipe. The pipe shop is an excellent illustration of the fact that repetition work in specialties leads to mechanical equipment and manipulation that lower production costs to an. astonishing degree. Hence cast-iron pipe, in dull times, has been sold at a few dollars a ton over the selling price of the pig iron used. On the other hand, these same pipe, shops make fittings .of many varieties, and in much smaller quantities, where the cost is high, and when pipe may be sold, say, at $50 a ton, the fittings on the same shipment will be sold for nearly double that price. The history of pipe-making, in the United States, is a checkered one the mortality of plants is high and, from the nature of the industry, plants must be large to live. In spite of the fact that the best processes must be used to turn out this rather strict specification material, pipe is easy to make and a pipe plant is more of a tonnage mill than the really high-class specialty foundry it should be. Every time, therefore, that the demand for pipe is strong new shops spring up, only to close when the demand has ceased, but the financial damage to the more permanent plants has been done. Both the South and the North have had abundant experiences of this kind, and when recently a northern Public Service Corporation gave its order to France, the pipe plants thus adversely affected were content to have this occur rather than see-a plant started to supply the surplus demand.

Jan 9, 1924

By P. Greenfield, C. C. Smith, A. M. Taylor

J. E. Harris (Berkeley Nucclear Laboratories, England)—Greenfield et al.11 attribute abrupt changes in slope of their log o/log i curves for heat-treated Mg/0.5 pet Zr alloy (zA) to &apos;atmosphere&apos; locking. It is proposed here that a more reasonable explanation of the apparent strengthening at low rates of strain can be based on precipitation either during the preanneal or during the creep tests. All the tests were carried out above 0.5 Tm where solute atmospheres are likely to be largely evaporated2 and can migrate sufficiently rapidly so as not to impose any &apos;drag&apos; on the moving dislocations. McLean3 has derived an expression for determining the temperature Tc above which, due to the high-migration rate of the atmospheres, Cottrell or Suzuki locking can play no part in determining creep strength. This expression, which holds for an applied shear stress of not greater than 5 X 107 dynes per sq cm is: Tc/Tm= 7/6.8 - log10? where i = secondary creep rate The values for T, corresponding to the maximum and minimum reported creep rates at each temperature have been calculated from the data of Greenfield et al. These are given in Table VII. All the test temperatures were above T,, the margin being greater for the higher temperatures and for the lower strain rates where the breaks in the log s/log ? curves occurred. Dorn and his collaborators14, 17 have studied systematically the effect of solute hardening on the creep properties of an A1/3.2 at. pet Mg alloy. In the temperature range where strain aging occurred in tensile tests, abnormally high-activation energies for secondary creep were obtained but at temperatures above 0.43 Tm, solute alloying did not have any effect on the creep parameters. Moreover, there have been no reports of any strain aging phenomenon during elevated temperature tensile tests with ZA material.18 Instead of the observed strengthening being due to atmosphere locking, it is now proposed that precipitates play an important role in enhancing the creep strength of the material. There are two possibilities—precipitation of zirconium hydride during the high-temperature preanneal and/or precipitation of the hydride or a-zirconium during creep. On the basis of the former the results can be interpreted in terms of a critical stress being necessary to force the dislocations through or over preexisting precipitates. From the latter, if the strengthening is due to pre- cipitation during the test then hardening should be associated with a critical strain rate. At low rates of strain, time is available during the tests for precipitation to occur either directly onto dislocations (thus pinning them) or generally throughout the matrix (which would impede dislocation movements). Examination of the data of Greenfield et al. suggests that both mechanisms may be operative since they observed precipitation during creep and also found that their alloys exhibited high-creep strength in the early stages of the low-stress tests, i.e., before creep-induced precipitation had time to occur. It is not easy to understand why they considered that precipitation of zirconium hydride is unlikely to occur at 600°C while it can take place in tests in air at as low a temperature as 200°C. Precipitation of the hydride during the preanneal cannot be ruled out merely on the basis of metallographic examination. Hydride precipitates in ZA type alloys are very small and can only be accurately resolved in the electron microscope.9 For example, in this laboratory20 hydride platelets with major dimensions <(1/10) µ have been observed by electron transmission through thin film specimens of hy-drogenated ZA material. Complex interactions between dislocations and such particles are illustrated in Fig. 12. Additional evidence for precipitation during pre-annealing is provided by the data presented in Greenfield&apos;s Fig. 1 and Table IT. These show that the creep strength at 200o and 400°C increases with the time of preanneal at 600°C. Such increases cannot be explained on the basis of increases in grain size alone for further improvements in strength were observed when the material was annealed for longer times than that required to stabilize the grains. Although the main discussion is confined to ZA material, similar arguments can be used against the strain aging hypothesis proposed to explain the binary Mg/Mn alloy data. In this case no precipitation is possible during the preanneal, but precipitation-hardening during creep can occur.

Jan 1, 1962

By McQuiston. F. W., E. C. Tveter

Sulfide mineral flotation has been applied to all naturally occurring sulfides and several synthetics. Of even more importance is the fact that economic separations are now being made between sulfides of essentially all the different metals. The variety of methods and minerals involved in such practice make it difficult to characterize them except in terms of general factors which influence the practices used. Ore grade and mineral composition are the major factors determining the processing method and the extent to which processing must be carried to achieve optimum economic return for a given ore. Since the choice of treatment is also affected by such factors as mine location, shipping charges, smelter schedules, each ore is a separate problem even though mineralization may be similar; The dissemination of minerals in the ore naturally determines the fineness of grind required for liberation. However, since grinding costs are a major part of most milling costs, emphasis has been placed on means of rejecting gangue minerals at the coarsest size possible. This has led to increased flotation of middling products or bulk concentrates for subsequent regrind and retreatment. Reagent development has also played an important part in present plant practice. Relatively few new frothers and collectors have found application during the past 25 years and many have disappeared. In general practice, re- agent combination choice is now fairly consistent with the type of collector being chosen on the basis of the mineral to be floated, the frother on the basis of pulp alkalinity, and the modifiers primarily on the basis of minerals to be rejected. REPRESENTATIVE FLOTATION PLANTS The milling operations described in this chapter have been selected primarily to illustrate these differences in ores and processing methods for the major types of ore minerals. The compositions of these minerals are shown in Table 1. These concentrators were chosen as representatives, both on the basis of geographic location and mineral content of the ore treated. At least one mill is included from each of the major producers, but the primary object was to show the practice employed for the various ore minerals and the different approaches to the middling problems encountered. The individual plants which have contributed data to this study are listed in Table 2, with a summary of their operating data, and are discussed in the order shown.

Jan 1, 1962