Search Documents

By H. R. Hardy

The study of the mechanical properties of geologic materials was initiated in the Mining Research Section of the Fuels and Mining Practice Division in 1951 as part of a fundamental study of ground stress in Canadian coal mines.1 Early in the investigation of the mechanical properties of geologic materials, however, it was realized that the test results are influenced by the rate and the duration of loading. For this reason, laboratory investigations2,3 were undertaken to study the effect of long-period uniaxial stress on the deformation and failure properties of these materials. A literature survey indicated that work on the time-dependent properties of geologic materials had been very limited in the past.

Jan 1, 1965

By John G. H. Crump, E. W. Owen, Peter P. Gregory

A noticeable decrease in activity characterized the year 1938 in the West Texas area. The total number of wells completed dropped to 2045 for 19381 as compared with 2806 completions in 1937,l a decline of 27.12 per cent. This trend contrasts the sharp increase of 76.29 per cent in completions in 1937 over the 1936 total. Of 2045 well completions during 1938,' 1788 were oil wellsll 16 were gas producers1 and 241 were listed as failures.' During 1938 the ratio of dry holes drilled to oil-producing or gas-producing wells completed was one dry hole to each 7.48 oil wells, which compares with one dry hole drilled to each 7.477 oil wells in 1937. Nearly 200 wells drilled during 1938 in West Texas were either wildcat or partly wildcat wells, an increase of about 25 over the year 1937, when approximately 175 wells drilled were so classified. The 200 exploratory wells drilled represent about 10 per cent of the total number of wells completed. West Texas produced 71,257,541 bbl.1 of oil in 1938 as compared with 75,743,000 bb1.2 of oil in 1937, a decrease of 4,485,459 bbl., or a 5.92 per cent decline. By comparison, West Texas produced 22.36 per cent more oil in 1937 than during 1936. In December 1938, the 9247 producing oil wells in West Texas1 averaged 22.08 bbl. per day per well as compared with December 1937, when 7571 wells1 produced an average of 25.18 bbl. per day per well, or a decline in daily well average of 12.32 per cent. Discoveries No outstanding new fields were discovered in West Texas during 1938, in spite of continued, active wildcatting operations. Several new oil-producing areas were, found, however, the value of which is still unknown.

Jan 1, 1939

By E. W. Owen, John G. H. Crump, Peter P. Gregory

A noticeable decrease in activity characterized the year 1938 in the West Texas area. The total number of wells completed dropped to 2045 for 19381 as compared with 2806 completions in 1937,l a decline of 27.12 per cent. This trend contrasts the sharp increase of 76.29 per cent in completions in 1937 over the 1936 total. Of 2045 well completions during 1938,' 1788 were oil wellsll 16 were gas producers1 and 241 were listed as failures.' During 1938 the ratio of dry holes drilled to oil-producing or gas-producing wells completed was one dry hole to each 7.48 oil wells, which compares with one dry hole drilled to each 7.477 oil wells in 1937. Nearly 200 wells drilled during 1938 in West Texas were either wildcat or partly wildcat wells, an increase of about 25 over the year 1937, when approximately 175 wells drilled were so classified. The 200 exploratory wells drilled represent about 10 per cent of the total number of wells completed. West Texas produced 71,257,541 bbl.1 of oil in 1938 as compared with 75,743,000 bb1.2 of oil in 1937, a decrease of 4,485,459 bbl., or a 5.92 per cent decline. By comparison, West Texas produced 22.36 per cent more oil in 1937 than during 1936. In December 1938, the 9247 producing oil wells in West Texas1 averaged 22.08 bbl. per day per well as compared with December 1937, when 7571 wells1 produced an average of 25.18 bbl. per day per well, or a decline in daily well average of 12.32 per cent. Discoveries No outstanding new fields were discovered in West Texas during 1938, in spite of continued, active wildcatting operations. Several new oil-producing areas were, found, however, the value of which is still unknown.

Jan 1, 1939

By Robert Anderson

OLIVER C. RALSTON, Salt Lake City, Utah- (communication to the Secretary *).-The literature on the theory of flotation has been enriched, of late, by the views of a number of excellent mining engineers who unfortunately were tyros in physical chemistry and physics. Hence the obscurity and mystery with which the process is supposed to be surrounded. The present paper goes far toward explaining some of the ideas which have seemed obscure or which have been poorly expounded by the men who advanced them, but there are a number of places where the author's explanations are unsatisfactory, or where he has fallen into the same mistakes made by the original propounders of the theories involved. While recognizing the value of constructive compilation, it is nevertheless disappointing to find a paper reviewing the recent theories of flotation which presents nothing-new-not even a new viewpoint. At the bottom of page 1121, there are stated to be present the following "phases" in flotation: "solid-liquid (ore-water), solid-liquid (ore-oil), solid-gas (ore-air)," etc. The writer could not possibly have meant to apply the word "phases" to the ideas involved. Each of the pairs of phases mentioned has an interface in which exists the interfacial tension that he is talking about.

Jan 12, 1916

By AIME AIME

AT the seventeenth National Metal Congress, held at Chicago, Oct. 1-3, the Iron and Steel Division and Institute of Metals Division participated with the American Society for Metals, American Welding Society, and the Wire Association in one of the most successful meetings ever held. The total attendance at the technical sessions and the scope of and interest shown in the exhibits at the Exposition were greater than at any of the "Metal Weeks" since the depression began. The Iron and Steel Division held two all-day symposia and one general session. The latter, at the International Amphitheatre, Wednesday afternoon, was the only one poorly attended. This was attributable, at least partly, to the location of the meeting roan.

Jan 1, 1935

By R. A. Matuszak

This paper discusses the major portion of the hoist (drag or crowd) system and it shows how static control accomplishes its major aims. In 1959, the first truly static control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the proven rotating amplifier control system has since proven to be much more. When they conceived the original system, the designers had much more in mind than simply replacing the rotating amplifier with one that had no moving parts. The long range plan, which started with the initial system consisting of an SCR (silicon controlled rectifier) preamplifier and magnetic amplifier power amplifier, called for eventually, a control system low in cost and maintenance, relatively simple in design and extremely reliable. The plan also included the elimination of as many of the shortcomings of the rotating system as possible. No small accomplishment, when it is considered that the rotating control system had been, with only minor modifications, the standard of the industry for 20 years. The final step in the original design plan called for the eventual development of an amplifier that could be used as one of the basic building blocks of the future. DEVELOPMENT RESULTS Since the successful unveiling of the first static control system, continuous development has resulted in a slow, but sure progression along the path described by the original plan. The first version of the new control corrected one of the shortcomings of the rotating system by removing the necessity of operator anticipation. This was accomplished by making the system faster in response so that the operator noticed virtually no delay between his movement of the master controller and that of the machine. Thus, after the operator became familiar with the operating characteristics of the machine, he was able to become more relaxed while digging. The natural result of this accomplishment was higher production. All of the subsequent versions of this new control were even faster than the initial design. Although it was not distinguishable by the operator, the further increase in response resulted in large gains in the limiting of transient torque peaks applied to the machine while digging. Also, a more effective control of the torque and power peaks was obtained when plugging the motion being controlled to a stop. (Plugging is the use of the Ward-Leonard ability to regenerate power and absorb energy from the load to

Jan 1, 1964

By David Segura

THE Huitzuco mercury deposits have been described by C. W. Vaupell,1 therefore the general information such as location, history, production, etc. will not be repeated here. The present owners acquired the property when the deep levels of the Cruz mine were flooded, and it was believed that a relatively large tonnage of low-grade ore and fills would be encountered in the flooded section, because f the early mining methods used in the Cruz mine. The mine was partly unwatered and about 187,000 tons of fills was pit-sampled in the San Cayetano stope. These fills average 2.4 kg. Hg per. ton. During the period of maximum production at Huitzuco, the ores were sorted in the mine and cobbed into 3-in. pieces, which were treated in Scott furnaces. Large pieces of raw ore are found in the sinter, and it is indicated that both recovery and, costs were not very satisfactory. Recent practice has been to treat the ores in closed retorts made of 10-in. pipes. Because f the presence of combined antimony in the mineral livingstonite (HgS.2Sb2S3) and considerable native sulphur, little or no metallic mercury is recovered in the condensers and a second retorting of the condenser muds is-necessary. This makes the treatment of the ores expensive and tends to low recoveries of mercury. The prin-cipal costs of retorting are, in their relative order: (1) fuel, (2) low recov-ery of mercury, (3) replacement of retort pipes, (4) labor.

Jan 1, 1938

By J. R. Eckel

It has long been known that mud properties affect drilling rate and that drilling with water is as much as six to .seven times faster than with mud. However, it is not known why drilling rates with mud are lower. Recent studies show what fluid properties govern microbit drilling rate and also provide a quantitative correlation of these fluid properties and hydraulics with microbit drilling rate. All the microbit tests reported in this paper were made with a low permeability (about 10 md) limestone. They were conducted at constant bit weight and rotary speed with varying fluid properties, flow rate Q and nozzle dinnteter d. The tests showed that (1) drilling rate in a given system with constant circulating rate and nozzle velocity is a function of the kinematic viscosity [viscosity /density, (cp)/ p (density)] of the drilling fluid measured at near bit nozzle shear rates; (2) the combined effect of fluid properties and hydraulics on microbit drilling rate is defined by a Reynolds number function (kQp/dp); (3) for the same kinematic viscosity, drilling rate is independent of solids content; and (4) for the same kinematic viscosity, drilling rate is independent of fluid loss. INTRODUCTION The fact that mudding up reduces rate of penetration is well known, but the reduction varies from well to well. The rate with mud may be 80 percent of the water rate or it may be as low as 15 percent. Since this reduction of up to seven-fold takes place under conditions of constant bit weight, rotary speed and mud circulating rate in a uniform formation, it can only be a result of the change in fluid properties. Previous work1-" both in field tests and in laboratory microbit tests) showed that drilling rate with mud is lower than with water (Figs. 1 and 2). Microbit tests also confirm, at least qualitatively, the field observation that drilling rate slows with increased pressure differential from borehole to formation (Fig. 3). The qualitative effect of drilling rate of bit weight, rotary speed and rate of mud circulation are also the same for the field and microbit rig. For these reasons, the industry generally accepts microbit results as being qualitatively meaningful in terms of field application.

By W. O. Philbrook, K. M. Goldman, G. Derge

T. Rosenqvist—The most interesting point in this paper is the observed transfer of iron into the slag in the initial stage of the desulphurization process, after which the iron again is reduced to the metallic state. The authors interpret this observation as showing that the sulphur enters the slag as an iron-sulphur compound which subsequently is decomposed by the slag. The present writer has previously suggested the following equation for the desulphurization process: S + O2- ? S2- + O For equilibrium in the blast furnace the oxygen potential is defined by equilibrium with graphite and CO of 1 atm pressure: C + O ? CO [2] During the desulphurization process the reactions proceed in the direction of the arrows. If one assumes eq 2 to be significantly slower than eq 1, the transfer of sulphur into the slag, in accordance with eq 1, will build up a local oxygen potential at the metal-slag interface very much higher than that corresponding to the value defined by eq 2. This is possible because the equilibrium oxygen potential in eq 1 is high as long as the sulphur content in the slag is low. This oxygen potential will again be able to oxidize some iron: Fe + O ? Fe2+ + O2- and an increase in the iron content of the slag will be observed. Adding up eqs 1 and 3 one obtains: S + Fe ? S2- + Fe2+ The net effect is thus in harmony with the experimental observation but is obtained without assuming any close ties between the sulphur and iron atoms during the process. Furthermore, it follows from eqs 1 and 2 that when the sulphur content in the slag increases, and equilibrium with C and CO is finally approached, the local oxygen potential at the metal-slag interface will decrease, and the iron in the slag will be reduced back into its metallic state. C. E. Sims-—The data and conclusions presented in this paper are thoroughly convincing in establishing the mechanism of sulphur transfer from iron to slag as in a blast furnace. The evolution of gaseous CO in step 3 of the reactions given on p. 1112 makes the process virtually irreversible. Assuming that the process is similar in slag-metal systems other than in the blast furnace, it is readily seen why free CaO and re-ducing conditions so greatly favor desulphurization. On the other hand, the very effective desulphurization obtained in oxidizing slags when strongly basic, must be attributed to the relatively high stability of CaS as compared to FeS. The ease and simplicity with which the reactions of classic chemistry agree with the experimental data and explain the mechanism is noteworthy. The concept of molecules of FeS, soluble in both phases (metallic iron is not soluble in the slag), migrating from the iron to the slag and there reacting with CaO, which is soluble only in the slag phase, is clear and uncomplicated. This is likewise true for step 3. Those who would deny the existence of molecules or molecular-type combinations in liquid iron, must strain to provide a mechanism so lucid. In the absence of molecules, the Fe and S exhibit a remarkable collusion. L. S. Darken—The investigation and interpretation of rate phenomena in the range of steelmaking temperatures is a difficult task. Most of the laboratory investigations of steelmaking reactions have been concerned with equilibrium. Having determined the equilibrium, our attention naturally focuses next on the mechanism and rate of approach to equilibrium. The authors seem to have contributed substantially to our understanding of these factors for the case of sulphur transfer. I should like to ask the authors whether they consider that the sulphur transfer reaction is diffusion controlled as many high-temperature reactions seem to be. If so, it would seem reasonable to suppose that the slow diffusion step of the process is the transfer across a pseudo-static layer or film similar to that considered in heat flow problems. As the diffusivity and fluidity are smaller for the slag than for the metal, it may tentatively be assumed that the sulphur gradient exists in a thin layer in the slag adjacent to the slag-metal interface and that the metal and the main mass of slag are each maintained uniform by convection. On this basis the amount of sulphur transferred across unit area per unit time is D p (?S%)/100 ?1, where D is the diffusivity, p the density, (?S%) the difference in percent sulphur on the two sides of the layer, and ?l is the layer thickness. At the beginning of the experiment the main body of the slag and hence one side of the layer contains no sulphur; therefore (?S%) may be replaced by (S%), the sulphur content of the slag at the slag-metal interface, which in turn is equal to L[S%] where [S%] is the sulphur content of the metal and L is the distribution coefficient. The rate of transfer thus becomes DpL[S%]/100 ?l, which the authors designate K[S%]. Equating these two quantities and setting D = 10-6 cm2 per sec, p = 3 g per cm3, L = 40, and K = lo-+ g cm-2 sec-1, it is found that ?l, the film thickness, is about 0.01 cm—a value of the order of magnitude of that found in heat transfer problems in liquids. The uncertainty of the numerical values used leaves much to be desired, but at least it can be said that this calculation tends to support the proposed model involving diffusion through a film. Although this does not seem to affect the general argument, I should like to call attention to the fact that the diffusivity3 of sulphur in hot metal is found (on conversion of units) to be about 10-4 cm2 per sec rather than 104 cm2 per sec as stated by the authors. The three equations written by the authors to express the steps in the overall process of sulphur transfer may alternatively be written ionically as only two Fe + S = Fe++ + S-- Fe++ + O-- + C (graphite or metal) = CO (gas) + Fe where the underscore is used to designate the metallic phase; ionic species are slag constituents. After the authors have so neatly demonstrated that iron and sulphur transfer together (at least initially), this fact seems almost self evident; from eq 4 it is seen that if sulphur acquires a negative charge during transfer

Jan 1, 1951

By J. H. Jackson, R. B. Fischer

VERY little is known about the properties of relatively pure refractory metals in the cast state since these metals are customarily made by powder-metallurgy methods. Recently, the development of the vacuum arc-melting furnace has made possible the study of large, sound ingots of cast molybdenum. The ductility of molybdenum, at room temperature, may vary considerably. Often the brittle state depreciates the utility of molybdenum, even for the material prepared by powder-metallurgy techniques. At the outset of this program, it was felt that if the causes of brittleness were to be determined it might be possible to reduce the difficulties met in the working of molybdenum. Also, the problem of producing strong, fusion weldrnents of molybdenum might be solved. The conditions required to produce ductile molybdenum by the powder-metallurgy technique are reasonably well known. A fibrous or elongated-grain structure has good ductility although this property is probably directional. The equiaxed structure obtained in fully recrystallized molybdenum has been considered to be brittle. The reasons for this behavior of molybdenum have not been established. The preparation of cast molybdenum ingots by the vacuum-arc method was described by Parke and Ham.' By this method, ingots weighing up to 250 Ib were produced." Parke and Ham1 found that molybdenum ingots containing more than approximately 0.0025 pct oxygen could not be hot forged. On the other hand, they found that fully deoxidized cast molybdenum, containing up to 0.06 pct carbon, could be hot forged. However, the as-cast ingots containing either carbon or oxygen were brittle at room temperature. Parke and Ham,1 Woodside,3 and Zapffe, Landgraf, and Worden4 noted the inter-granular precipitation of oxide or carbide in cast molybdenum. This study—part of an extensive program on mo-lybdenum—had the following objectives: (1) To investigate the causes for the brittleness of cast molybdenum at room temperature, (2) to investigate the means for improving the ductility of cast molybdenum at room temperature, and (3) to add to the knowledge of cast molybdenum and of cast metals in general.

Jan 1, 1951

By E. I. Salkovitz, F. W. von Batchelder

AS Slawson1 and others have already shown, from a geometrical view twinning in the diamond structure may be considered as a reflection across a (111) plane or as a reflection across a (112) plane. An analysis by Ellis and Treuting2 showed that the twinning plane must be the (111) plane, but that a twin might have lateral boundaries along (112) planes. Earlier Slawson1 and Ellis3 had shown that only (111) twinning was present in diamond and germanium respectively. Since an ingot of silicon, 1 in. in diam and 1 1/2 in. long, prepared from Dupont silicon to which 0.2 pct Be had been added was available, it was examined for twinning. The ingot had been cooled slowly from the bottom. A section 1/16 in. thick was ground off from the bottom and then the ingot was sliced vertically through the center. Spectrographic analysis indicated only faint traces of iron and silver, in addition to the beryllium. The sample was first etched with a hot solution of 10 pct NaOH in water.and photographed. Back-reflection Laue patterns were made of the vertical and horizontal sections in the regions designated in Fig. 1. Orientations were obtained for each twin using the Greninger technique. Several regions of the same orientation were found; thus regions A and K were identical, similarly N and P, and C, G, J, and L. Knowing the angles between the traces of the twinning plane on the surface and the specimen axis, the indices of the twinning plane were deduced. In all cases the twinning plane was found to be (111); lateral boundaries, however, were found which were (112) such as the one indicated in Fig. 1. Therefore, as in the case of diamond1 and germanium' only (111) twinning occurs in silicon. We wish to thank Mr. Hino for the use of the ingot as well as for its metallographic preparation. References 1C. B. Slawson: American Mineralogist (1950) 35, p. 193. 2 W. C. Ellis and R. C. Treuting: Trans. AIME (1951) 191, p. 53; Journal of Metals (January 1951). 3W. C. Ellis: Trans. AIME (1950) 188, p. 886; Journal of Metals (June 1950).

Jan 1, 1953

By John V. Beall

Spots Goblenski fluffed up his pork chop sideburns, checked the angle of his wide brim Stetson and ambled off the airplane. The pert Braniff hostess stood smartly at the door. "Goodbye now, take care," she said in the special airline stewardess voice superimposed on a Texas drawl. Spots smirked, "You betcha, Peaches, you too." It was a crystal clear, sunny day which New York can have at any season of the year (but rarely gets credit for) and being in high spirits Spots did not mind being captured by a cab driver. That is the cab driver brushed aside all other conversation to give a continuous colorful commentary on New York politics, revealing in the process that only the very wealthy and cab drivers share the same political views in that city. After installing himself in the fading opulence of the Hotel Roosevelt, he finished the day with a steak dinner with baked potato under sour cream and hearts of lettuce salad with Roquefort dressing at the Black Angus restaurant. The next morning he had an appointment with Hemphill, Frye and Louderdock. The offices of this prestigious firm of management consultants are high in the Pan Am Building. He was courteously received by a lacquered receptionist and was soon escorted into the presence of Mr. John Smith. "Ah, Mr. Goblenski; Spots, isn't it? Hope you had a good flight. Lovely weather we are having. Just make yourself comfortable over there, Spots." Smith seemed cordial and Spots slipped comfortably into the interview. He had always thought that management consultants were evolved from the "efficiency experts" made famous by the radio team, Amos and Andy. He associated the modern version with computers, PERT and other systems approaches. He was surprised that one of these firms was apparently acting as an employment agency. "Of course" continued Smith, "in evaluation of basic criteria of performance moduli, the human element enters, Spots, and that brings us to you." Spots sat up and focused his attention.

Jan 1, 1970

Jan 1, 1920

By Walter G. Perkins

As this particular product holds a place by itself, it seems desirable to give a paper dealing especially with it as a corollary to my paper entitled " The Litharge Process of Assaying Copper-Bearing Ores and Products, and the Method of Calculating Charges."* The process is first to convert the metallic copper into matte by the addition of sulphur, allowing the two elements to combine at the bottom of the crucible when heat is applied. The

Jan 1, 1903

By Jan H. Hommen

TRENDS IN MINE FINANCE Reviewing historical trends may help in dealing with future funding strategies. The first trend is the increase in the use of debt to fund corporate America. Surprisingly, when comparing that with other corporates in the global marketplace, the U.S. does not look too poorly. Japanese, in particular, but also German companies, are much more leveraged than their U.S. counterparts. Note that in Japan and Germany the government and the consumer have shown substantial restraints when it comes to credit. Not so in the U.S. where the savings rate (4%) is much lower than that in Japan (20%) and in Germany (14%). As a result, the cost of leverage is substantially lower in Japan and in Germany than in the U.S. Lower debt costs in these countries allows one to obtain more of it for the same price. The close relationships between financial institutions, corporations and governments in Japan and Germany also make the risk of leverage more bearable and understandable. Also note that interest rate volatility in these countries is more subdued. The investor base in common stock is also changing. Private pension funds have been net sellers of equities during the last few years while public pension funds have been net buyers. Individuals are basically out of the market. It is estimated that over $330 billion of equity was retired in the U.S. through 1986-1988. The reasons are well known: restructurings, buy-backs, takeovers, mergers, and buy-outs. This de-equitization is likely to continue as the cost of equity capital is higher than the cost of debt capital, even on a before-tax basis. Because there has been no market for equity since October 19, 1987, junk bonds have replaced equity capital in the corporate finance structure. The non-investor-grade borrower has access to the public markets through high-yielding debt securities that often look like senior equity. Deregulation has also provided 24-hour markets; securitization can now liquify assets that before were rusting on balance sheets; information processing and communication tools give facts that are instantaneously available, creating the need for products to cover risk and exposures unknown before the start of the information and technology explosion. Thus we now have swaps, options, futures, options on futures, caps, as well as program trading, portfolio insurance, index funds, etc. Globalization will be unstoppable. Today's environment demands it. Corporations are now global competitors, even though they may have never shipped a product off-shore. Boundaries are disappearing and impediments have been removed. Stocks can be issued in a global offering with distribution in all major financial centers of the world. The high leverage of Japanese companies has made common stocks very scarce, which with the high savings rate, makes equity capital inexpensive in Japan. If markets were perfect everyone would issue stock in Tokyo and buy it back in New York. This would certainly stop the bleeding on the balance of payments. With the deficit balance of payments in America, it is no surprise that the cost of money is expensive here. The risk-return relationship on U.S. equity is not favorable enough to appeal to Japanese equity investors. The Tokyo-market, helped by a stronger yen, surpassed New York as the most important equity market in the world. The question is, will the Tokyo market hold up when Japanese domestic consumption increases at the expense of savings? In the U.S. debt markets, the plain vanilla debenture is making a comeback after a period of absence. Commercial paper has replaced short term bank borrowings for working capital funding by larger corporations. The banks have made an interesting comeback with loan sale programs that will continue to attract borrowers. There will be a continuing

Jan 1, 1990

By Francois E. Heuze

Today, the favored option for disposal of high-level nuclear wastes is their burial in mined caverns. As an alternative, the concept of deep disposal by rock melting (DRM) also has received some attention. DRM entails the injection of waste, in a cavity or borehole, 2 to 3 kilometers down in the earth crust. Granitic rocks are the prime candidate medium. The high thermal loading initially will melt the rock surrounding the waste. Following resolidification, a rock/waste matrix is formed, which should provide isolation for many years. The complex thermal, mechanical, and hydraulic aspects of DRM can be studied best by means of numerical models. The models must accommo¬date the coupling of the physical processes involved, and the temper¬ature dependency of the granite properties, some of which are subject to abrupt discontinuities, during [a]- ß phase transition and melting. This paper outlines a strategy for such complex modeling.

Jan 1, 1982

By Fuad S. Maayeh, Robert J. Evans, Paul M. Yavorsky

A description and capabilities of the Mine Roof Simulator at the Pittsburgh Mining Technology Center is illustrated for testing longwall roof support equipment. This unique Mine Roof Simulator has the capacity to exert 3 million lbs. of compressive force vertically and 1.6 million lbs. of force horizontally to simulate loads on hydraulic supports typically found in longwall mining. The supports that undergo testing are instrumented with strain gauges and photoelastic coatings such that critically strained areas become readily apparent. These critically strained areas are redesigned or retrofitted with appropriate reinforcement and retested. A data base will be accumulated from several support designs that will lead to an optimized design that will have the potential to reduce downtime by malfunctions of supports and thus increase productivity. A typical test procedure and analysis is given for a two leg 350 ton shield along with a description for placement of strain gauges, displacement gauges, and hydraulic pressure monitors for critical sites.

Jan 1, 1982

By Meguru Nagamori

DURING the smelting of the sulfide ores of copper, nickel, and certain other metals, a matte phase is formed. For a better understanding of the physico-chemical properties of mattes, binary systems such as Cu-S, Ni-S, Fe-S, and so forth, should be studied, especially in the vicinity of liquid compounds such as Cu2S, Ni3S2, FeS, and so forth. These compounds are relatively stable in the solid state although they can exhibit appreciable deviations from stoichiometry. With small deviations from stoichiometry there are large changes in the activity of both sulfur and metal this is a characteristic of both solid and liquid sul-fides near the stoichiometric compositions. In the vicinityof molten Cu2S,1 for instance, the activity of sulfur increases about 100 times for a 0.012 increase in the mole fraction of sulfur and, correspondingly, the activity of copper decreases greatly. In this sens the minor deviations from stoichiometry should be carefully taken into account in studies of such metal-sulfur melts. Metal-sulfur melts may be considered to have properties intermediate between metallic solutions and molten salts, i.e., neither entirely metallic nor entirely ionic. The radius of the ion sZ- is 1.84 as compared with 1.04? for a single bond covalent s.2 It is therefore inferred that when the sulfur is more ionic its partial molar volume is larger, although metal-metal, metal-sulfur, and sulfur-sulfur interactions may bring about further complexities. Thus, it is to be expected that the molar volumes, which are derived from density-composition relations, will help in resolving the structure of the melts. In this study the maximum bubble pressure method with bubbling gases of H2, H2S, and Ar, .was employed to measure the density. EXPERIMENTAL Materials. Silver of 99.95 pct purity was melted in an alumina crucible and hydrogen gas was then bubbled through the liquid for the deoxidation. In preparation of Cu2S, electrolytic copper powder (>99.9 pct Cu) was mixed with precipitated sulfur and heated to 1200°C in an alumina crucible under a hydrogen atmosphere. Mixtures having the approximate compositions FeS and Ni3S2 were prepared by heating reagent grade electrolytic iron or reduced nickel powder with precipitated sulfur under a hydrogen atmosphere. The H2S gas was of 98.5 pct purity, the impurities being mostly CO2 and CS2 which hardly contaminate the melts. Apparatus. The crucible system is shown schematically in Fig. 1. To minimize the variation of melt composition during a density measurement, the apparatus was designed in such a way that either Ar, H2, H2S, or mixtures of these gases could be used as the bubbling gas. When the melt had a high partial pressure of sulfur, H2S gas was used. When the partial pressure of sulfur was so low that oxygen might dissolve in the melt, the use of H2 was preferred. In intermediate cases, argon or mixtures of H2-H2S were used. Density of Dibutylphtalate. Dibutylphtalate was used as the manometer fluid. Relative to distilled water, the density of the dibutylphtalate, pdib g per cc, was measured and found to be: pdib (25°C) = 1.046 i 0.002. With the use of the temperature coefficient reported by Kemppinen and Gokcen,3 the following value was

Jan 1, 1970

By M. C. Smith, W. V. Green, D. M. Olsen

The creep-rupture behavior of commercial powder-metallurgy molybdenum rod is reported in the temperature range 1600" to 250O°C, at stresses up to 9000 psi and times up to 1 month. The effects of temperature, stress, and grain growth are discussed. Rupture time is fitted to the Larson-Miller parameter and compared to lower-temperature and higher-stress results reported by pugh.1 BECAUSE of its high melting point, molybdenum should retain useful strength to relatively high temperatures. Combined with its ready availability in the United States, this makes it attractive for many applications in missiles, rockets, and so forth—wherever its susceptibility to oxidation can be tolerated or overcome. The mechanical properties of molybdenum rod in the temperature range —200" to 1540°C have been reported by pugh,' Bechtold,' Parke,3 and Carriker and Guard.4 Madden and chen5 have measured the tensile properties of molybdenum single crystals in vacuum up to about 2500°C. As one further step in evaluating its mechanical usefulness, the constant-load creep-rupture properties of commercial powder-metallurgy molybdenum rod have been investigated in the range 1600" to 2500°C. MATERIAL TESTED Creep specimens were machined from 1/2-in. round commercial molybdenum rod, manufactured from powder by pressing, sintering, and swaging. Spectrochemical analysis of the rod showed "traces" (less than 0.01 pct) of silicon, aluminum, chromium, iron, and zirconium, and "faint traces" (less than 0.001 pct) of manganese, magnesium, cobalt, and nickel. Carbon content was 130 to 200 ppm, nitrogen was 110 to 180 ppm, and oxygen 30 to 35 ppm. A typical microstructure of the as-received rod is shown in Fig. 1. Room temperature tensile properties for five specimens strained at about 0.015 in. per in. per min are shown in Table I. CREEP SPECIMENS USED The specimens used for creep-rupture testing are illustrated in Fig. 2. The 1/4-in.-diam gage section was 3/4 in. long, and terminated at shoulders 5 mils high. These shoulders served as fiducial marks for optical strain measurements. Surface finish on the gage section was 16pin. r.m.s. One specimen, for a "long-time" test described below, was modified by dividing the 3/4-in. gage length into three 1/4-in. long sections with individual diameters of 0.250, 0.230, and 0.210 in., each terminating in a pair of fiducial shoulders. TESTING PROCEDURE The constant-load creep-testing machine used has been described by Smith, Olson, and Brown.6 In it the specimen is held vertically on the axis of a cylindrical tantalum or tungsten heater tube by threaded molybdenum or tungsten grips. Both specimen and grips are heated by radiation from the heater-tube, which is heated by its own electrical resistance. The bottom specimen grip is held at its lower end by a clevis pin. The testing load is applied to the specimen through the upper grip by means of hanging weights, a constant force-multiplication lever system, and a pull rod sealed to the chamber lid by a bellows. The incandescent specimen is viewed by an external optical system through slots in the heater-tube and radiation shielding, and an enlarged image of it is projected on a ground-glass screen. Gage-length measurements are made on this image with a pair of cathetometers. Thorium oxide coatings were applied to the threaded ends of most specimens, to prevent diffusion-welding of specimens to grips during testing. Without such a coating welding usually occurred, and grips were often broken by subsequent efforts to remove the tested specimens.

Jan 1, 1960

Plans for the fall meeting of the AIME, to be held in conjunction with the Centennial of Engineering -marking the 100th anniversary of the Society of Civil Engineers-indicate that the Chicago gathering will be one of the most significant in Institute history. Headquarters for the six divisions represented will be the Palmer House. Twenty technical sessions will be held from September 3 to 6, with papers of industry-wide impact to be presented. The papers will follow the theme of the celebration-a century of engineering progress. The MBD will start the ball rolling with morning and afternoon sessions Thursday, September 4. A luncheon also will be held. MBD has scheduled morning and afternoon sessions for the following day as well. MGGD, Iron and Steel, and the Coal Div., will hold sessions Friday afternoon. The Industrial Minerals Div. plans an executive meeting, 5 pm, Friday. Geology Subdivision is slated for morning and afternoon sessions Saturday. The Coal Div. will meet again Saturday morning.

Jan 1, 1952