Search Documents

By Manuel Gomez

Coking time was investigated as a function of coal properties, carbonization parameters, and the interactions between these variables. The results indicate that coal properties and carbonization conditions interact to influence the coking time, and these interactions may be determined quantitatively. Prediction equations were developed and used to simulate the effects of bulk density, flue temperature, and oven width on coking times for coals having a wide range of properties. The data presented provide additional information on the carbonization process to permit the coke oven operator to maintain closer control of coke production and coke uniformity.

Jan 1, 1968

By J. M. N. P. C. Teles, Venda Oliveira P. J., Correia A. A. S.

"AbstractA laboratory work was performed to study the mechanical behavior of a Portuguese soft soil chemically stabilized with binders and reinforced with metallic fibers when subjected to tensile stresses. To this end and in order to compare the tensile strength results done by two different tests, there were conducted two types of experimental tests: Tensile Split Strength Tests (TS) and Direct Tensile Strength Tests (T). The samples tested had the same binder quantity and different fiber contents, which allowed the characterization of the tensile behavior of the stabilized and reinforced soil, as well as the definition of the best fiber content. Results show that the binder is the main parameter controlling the behavior of the stabilized and reinforced soil until failure, while the influence of the fibers is noticed mainly at the post-failure behavior. The comparison between the tensile strength done by T and TS tests shows that the tensile split test can be used to estimate the tensile strength, although its results are lower than those obtained by the direct tensile tests in general.IntroductionDue to its poor mechanical characteristics, the construction on soft soils presents difficulties that require the use of soil improvement techniques such as chemical stabilization. However, even when mixed with binders, the tensile strength of the stabilized soil is poor, requiring, in certain cases, the use of expensive steel reinforcement or metallic beams, with obvious impact on the final cost of the work. Thus, for the cases where the tensile strength is a design requirement, the soil stabilization should be design with another element, whose primary role is to give tensile strength to the improved soil (Teles 2013).To fill the lack of published studies focused on soft soils both chemically stabilized and reinforced with metallic fibers, the present research aims to analyze the behavior of the improved soil when subjected to tensile stresses. To support the research there were conducted direct tensile tests (T) to directly measure the tensile strength of the samples and tensile split tests (TS) or Brazilian tests to obtain it indirectly. The samples tested had the same binder quantity but five different fiber contents in order to study the influence of the fibers in the improved soil behavior. In addition, a comparison between the results of both tests was made."

Jan 1, 2014

By Brian FitzPatrick, Michael J. Weaver

Everyone has a role in site safety, even consultants. This paper presents a summary of how a geotechnical and environmental consulting firm, with field staff on construction and subsurface explorations sites, engaged their staff and leveraged relationships with contractors to assess the construction related risks to which its staff members are exposed. These findings were then integrated into their technical training materials for both new staff and those needing a refresher, so that safety is discussed at the same time as the technical work and not treated as a separate topic. The paper outlines the process of identifying and evaluating the construction related risks that staff members face and presents examples of how the consultant can engage contractors in the process. By doing this, knowledge can be shared and there is a better mutual understanding of the risks associated with common construction and exploration related field tasks. The work resulted in an increase in staff engagement in safety, a better understanding of the true risks that staff face in the field, better relationships with contractors, and lower safety metrics. HISTORY At Haley & Aldrich, Inc., we renewed our safety journey in May 2012. Like many others, we had concerns over injuries our staff experienced in the three previous years, and a potentially significant utility strike we experienced while excavating a trench. In 2009, 2010 and 2011 we experienced an increase in recordable injuries, including two significant injuries, which caused our Experience Modification Rate (EMR) (see note below), Total Recordable Incident Rate (TRIR), and Days Away-Restricted, and Transferred Rate (DART) to rise significantly. See Fig. 1 for details. This caused us to step back and review our approach to safety, and our “safety culture”. The rise in reportable incidents and injuries also corresponded to the beginning of a growth period for the company.

Jan 1, 2019

By Julius Benavides Valdivia

El presente texto señala el proceso de construcción de la planta de tratamiento de agua potable desarrollado en Arequipa. El proyecto de agua potable es uno de los más importantes planeamientos que se realiza bajo la supervisión del Servicio de Agua Potable y Alcantarillado de Arequipa (Sedapar) con el apoyo económico de Sociedad Minera Cerro Verde. Asimismo, esta planta permitirá que muchas viviendas ubicadas en las zonas altas de la ciudad de Arequipa reciban agua potable en mejores condiciones, lográndose que las aguas de la PTAP La Tomilla y algunos manantiales, conserven el recurso para futuras necesidades, a fin de que pueda extender su acción, no sólo en su ámbito sino también en el tiempo.

Sep 12, 2011

By Chas. F. Jackson

The annual reports of the supervising engineers of the nine sections comprising the Mining Division are assembled here and constitute the annual report of the division. In planning activities the aim is to adapt them to changes in conditions, in the needs of the mining industries, and in the public interest; those that contribute most to solving the present problems are emphasized, investigations of less immediate importance being recessed if necessary. The strategic minerals investigations of the bureau afford an example of this change in emphasis to problems of immediate and urgent interest, and during 1941 they comprised, upon the basis of appropriations and expenditures, more than 90 percent of the work of the division.

Jan 1, 1941

By A. C. Johnson

The Bureau of Mines explored the Three Kids deposit in 1941 as part of a strategic minerals program. Earlier mining and exploration had established the presence of a substantial tonnage of medium-grade wad ore, and drilling and sampling by the Bureau of Mines, in collaboration with the Federal Geological Survey, indicated an additional tonnage such that development and exploitation became more clearly feasible. Private interests, with Government support, undertook to produce metallurgical-grade manganese. The present paper describes the Bureau of Mines exploration and subsequent development. Manganese in the Three Kids area is found in one of the lower members of the Muddy Creek formation in a bed of fine sandstone and silt, which outcrops around the north edge of the River Mountains and generally dips 20° to 40° away from the hills. There is considerable variation in the thickness and grade of the ore. The ore is light weight, having a density of 1.2 to 2.

Jan 1, 1956

By Graham A. Davis

?The ideas of economists and political philosophers, both when they are right and when they are wrong, are more powerful than is commonly understood. Indeed, the world is ruled by little else. Practical men, who believe themselves to be quite exempt from any intellectual influences, are usually the slaves of some defunct economist. Madmen in authority, who hear voices in the air, are distilling their frenzy from some academic scribbler of a few years back. I am sure that the power of vested interests is vastly exaggerated compared with the gradual encroachment of ideas. . . . But, soon or late, it is ideas, not vested interests, which are dangerous for good or evil.? John Maynard Keynes The General Theory (1936) Policy analysts, economists and others have tradition-ally considered mining and mineral wealth a boon, providing rich countries with the resources needed to sustain their modern industrial economies while helping poorer countries generate the foreign exchange, tax revenues and other assets necessary for economic growth and development. Nevertheless, this conventional view has always had its critics.

Jan 1, 2008

By Barnet Clemente, David Huaman

El sostenimiento de las labores en las operaciones mineras, son cada vez más consistente y seguros con la aplicación del concreto lanzado, en la unidad minera cerro lindo se ha migrado a este tipo de sostenimiento en un 100%. Todas nuestras labores están sostenidas con shotcrete, incluso el frente de la labor aplicamos el sostenimiento con shotcrete, que llamamos malla de sacrificio, sin embargo este tipo de sostenimiento es costoso, pero te da muchas facilidades para mejorar los rendimientos y se hace más segura la mina, para lo cual contamos con una planta de concreto exclusivamente para este servicio, con una capacidad de 30 m3 por hora, lo que necesita la mina es 7000 m3 mensuales para cubrir todas la labores de producción, preparación y desarrollo, incluso hemos considerado la labores de rehabilitación y resanes por la misma operación minera, esta operación nos da una demanda de 9 mixcrets en operación y un stand by, con 4 alphas operativos y 1 en stand by.

Sep 1, 2017

By A. Korchevskiy

While Russia continues to be a worldwide leader in asbestos production, the environmental and health status around Russian asbestos mines is not well known and understood, internationally. A literature review was performed to evaluate the potential impact of Russian mining operations on mesothelioma incidence rates in the Ural region where the majority of the asbestos deposits are located. Asbestos that has been mined in this region includes chrysotile, crocidolite, and anthophyllite forms. The Nicholson-Peto (1986) model was applied to published exposure data and mesothelioma mortality statistics in different cities and villages of the Ural region to estimate mesothelioma potency factors (KM) for the various associated fiber types. It was demonstrated that mesothelioma potency factors, as determined by Berman and Crump (2008), could be used to predict mesothelioma risks of non-occupationally exposed individuals in locations where either pure chrysotile, or both crocidolite and chrysotile, are mined and milled. A mesothelioma potency factor was calculated for anthophyllite that appeared to be higher than expected based on previously published studies. The highest incidence of mesothelioma was identified in a community close to a crocidolite mine. The study confirms the validity of utilizing current risk models for non-occupationally exposed populations near asbestos mining activities where asbestos exposures are relatively low and provides methods of characterizing mesothelioma risk in the former Soviet republics (FSRs).

Feb 27, 2013

By D. F. Smith

The thermodynamic data presented in the literature for zirconium compounds are incomplete. Among the compounds for which adequate data are Zacking are zirconium fluoride and sulfate. This paper reports experimental heat-content values determined by the Bureau of Mines for these two zirconium salts throughout the temperature range of 273° to 1,200° K. No crystalline transformations were found in the two compounds investigated, and neither of the compounds melted over the temperature range studied. MATERIALS TESTED The Oak Ridge National Laboratories, Oak Ridge, Tenn., supplied the two zirconium salts used in this investigation. The zirconium fluoride was high- purity reactor grade material. The zirconium sulfate contained between 0.01 and 0.10 percent hafnium and calcium, and other elements in concentrations below 0.01 percent, A spectrographic analysis of the two compounds is given in table 1. Before use the compounds were dried at 400° C. for several hours to removed adsorbed moisture.

Jan 1, 1962

By Ingvar Bergqvist

El objetivo de la voladura de bancos es crear de forma económico un espacio ahuecado, donde los explosivos sean cargados para que el resultado óptimo de la voladura sea obtenido. Por ello, es necesario que toda la información pueda ser utilizada -en tanto determine los trazos de perforación y las cantidades adaptadas de explosivos. En ese sentido, el presente texto señala los diferentes métodos de cálculo de carga para voladura de bancos como el de trazo de perforación y cargas, donde estos últimos son los más idóneos de acuerdo a las fórmulas del texto.

Nov 1, 1977

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC). Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-431' the semiannual reports were resumed.

Jan 1, 1950

By Jeff Ardron

Unlike the first predicted deep-sea mining (DSM) boom 35 years, the public response to the re-emergent possibility of DSM is this time round is not entirely optimistic, with serious economic, social, and environmental concerns being voiced. In the intervening years, the troubling notion of the ‘resource curse’ has been popularized, whereby the economies of developing nations rich in natural resources (agriculture, minerals, and fuels), paradoxically appear to fare more poorly than their brethren who have fewer such resources. There have been a variety of explanations and counter-arguments regarding why the resource curse occurs, including how it can be ‘escaped’, and even some disagreement on whether it in fact does occur. Nevertheless, many commentators appear to agree that that the quality of governance is strongly implicated in the socioeconomic success, or failure, of these resource-dependent nations, and could indeed be the deciding factor. Unlike nations with diversified economies, the majority of the income from natural resource economies, in the form of royalties and rents, flows through national government; hence, good governance and fiscal management is of particular concern.

Sep 1, 2014

By Reda M. Bakeer

"An approach slab is the roadway segment that immediately follows a bridge intended to provide a smooth transition between the two elements. Some approach slabs have developed rough rideability with time due to differential settlement between the roadway embankment and the bridge. Soils in south Louisiana are generally poor and highly compressible and, therefore, pile-supported approach slabs were occasionally used. Timber piles of variable lengths are driven into the soft soils where no appreciable toe support exists. This resulted in the soils both supporting loads through shaft resistance and yet experiencing long-term consolidation settlement. Field testing and review of the records of over 120 approach slabs constructed in south Louisiana yielded the conclusion that their performance is primarily governed by negative skin friction (downdrag) imposed on the relatively short timber piles. A software (TU-DRAG) was developed to evaluate the deflection profile of a pile-supported approach slab based on its geometry and conditions of the underlying soils. It evaluates the effect of dragload considering the number and spacing of the piles at each transverse row and their variable lengths along the approach slab. TU-DRAG was utilized in the design of two transportation related projects which have been in service for more than 10 years.INTRODUCTIONThe problem of differential settlement at bridge approaches or “the bump at the bridge” has been recognized for many years. Research studies (1986, 1989, 1997, 2009 and 2013) by the Transportation Research Board (TRB) and the Federal Highway Administration (FHWA) provided comprehensive evaluations of the performance of bridge approach slabs by assessing their field conditions and construction and maintenance records. Various states have also performed their own studies to investigate the performance of bridge approach slabs. The studies considered various types of structures including soil- and pile-supported approach slabs, integral bridge abutments and open-end abutments. Recommendations were provided for the design of new structures and for maintaining and repairing existing structures. Guidelines were offered regarding tolerable movements of bridges and their foundations based on measurements of vertical and horizontal movements of 580 bridges Moulton (1986). Vertical and horizontal movements greater than 102 mm (4 inches) and 51 mm (2 inches), respectively, were considered intolerable. Tolerable limits for angular distortion (differential settlement to span length) were suggested to be 1/250 and 1/200 for continuous and simple spans, respectively. It was reported that a differential settlement greater than 13 mm (0.5 inch) at the bridge interface would be sufficient to constitute a “bump” requiring mitigation."

Jan 1, 2017

By Jorge Vargas Fernández

Con el objetivo de incrementar la productividad de la minería, se plantea la realización de una positiva acción nacional de formación y capacitación en todos los niveles de la industria minera a través de un análisis de la situación actual respecto de los mineros, ingenierios y técnicos. Por ello, el presente texto señala la descripción del sistema "B" en funcionamiento de la productividad minera y la tecnología adecuada a la realidad.

Nov 1, 1972

By José E. Rondoña

El presente trabajo desarrolla un estudio comparativo de la producción de dos tipos de hornos usados en la fundición de cátodos de zinc en la planta de La Oroya, para asi determinar cúal es el equipo más idóneo para futuras expansiones del proyecto. De los puntos comparativos se encontró que el horno SICE desarrolla más productividad de personal en operaciones, así como en el rendimiento de la energía eléctrica. Mientras que respecto de las consecuencias de las filtraciones del metal, se encontró que el horno Ajax es el más adecuado, dado que la producción de barras se afecta solo en la producción que el horno afectado representa en la instalación total. Por ende, es conveniente el uso de dos hornos SICE tamaño mediano dada la capacidad y productividad de esta.

Nov 20, 1967

By H. Reimer

The rates of return on investment are examined for several major Canadian mining companies. Because we are dealing with a highly cyclical industry, subjected to widely fluctuating metal prices, rates of return are examined over a 20-year period. Conveniently, the first decade examined reflects the period when the industry enjoyed incentives to develop deposits; during the second decade, incentives were reduced and the industry became the most heavily taxed industry in Canada. The high rates of inflation since 1973 have distorted the real rates of return on investment if one considers replacement cost.

Jan 1, 1977

By Hal W. Hunt

Steel and concrete piles and power-actuated hammers have developed almost entirely within the past 100 years. Prior to that time, piles were mostly timber, driven with a drop hammer or a maul. The Engineering News Formula ? for timber piles driven with a drop hammer at a factor of safety of six ? was promulgated by Wellington in 1888. Steel com­panies supplied fabricated and rolled shapes for piles in the early 1900's. The thin shell and then uncased concrete piles originated about that time. Now leads have become sophisticated to accurately spot a pile at any required batter. Hammers have grown to phenomenal size and vibratories are being accepted at full value.

Jan 1, 1984

By Freddy Salazar, Segundo Velasquez, Robert Montes

Compañía Minera Coimolache, ubicada en la región Cajamarca, es una empresa a tajo abierto que produce oro y plata. El mineral es lixiviado con solución de cianuro de sodio, proceso del que se obtiene una solución pregnant que posteriormente se trata en la planta de Merrill Crowe y ADR según su ley. Sin embargo, debido a las precipitaciones, el agua de lluvia incrementa el inventario de solución con cianuro en el proceso, por lo que se hace necesario su tratamiento en la planta de detoxificación de cianuro. Ante este panorama, se buscó la oportunidad de reemplazo del cloruro férrico, identificando el agua ácida proveniente del depósito de material estéril como principal candidato para este reemplazo

Sep 29, 2023

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989