Search Documents

By Bruce Richardson

A contractor-manufactured 4.75m (15'-7") diameter EPB shield excavated a 115m (375 ft) long tunnel under the San Antonio River as part of the Salado Creek to Dos Rios Pipeline Interconnect Project in San Antonio, Texas. Lignite, limestone concretions, and sandstone in the face of the tunnel required the use of disc cutters. Less than 7.6m (25 ft) of sand and gravel hydraulically connected the top of the tunnel to the channel of the river. Fully lagged steel ribs with filter fabric were used for initial ground support and water control. This and other contractor manufactured TBMs in the 1.2 to 4.75m (4 to 16 ft) range are presented with descriptions of the jobsites, equipment, performances, and problems.

Jan 1, 2008

The recovery by flotation of some complex uranium minerals such as brannerite and davidite is described. Anionic reagents used for flotation of iron and titanium oxides' are suitable. If care is taken, to emulsify the reagents the slime fractions may be satisfactorilytreated.INTRODUCTIONUranium ores are usually treated by direct leaching with acid or alkali according to the nature of the gangue materials. Concentration of the uranium minerals prior to leaching is not commonly practised because of the earthy nature of most uranium minerals and the difficult mineral dressing problem they pose. Some of the harder complex oxides such as davidite and brannerite are amenable to flotation. This is fortunate since they usually require an expensive, strong acid treat~ent to dissolve the uranium. Flotation tests were commenced in 1949 by officers of the South Australian Department of Mines stationed at Adelaide, first in the School of Mines, then in the University of Adelaide and finally in Departmental mineral dressing laboratories at Thebarton. Separation of daviditefrom Radium Hill and Mount Victoria ores, brannerite from Crocker's Well ore, and secondary uranium minerals from Myponga ore was attempted.The development of the flotation reagents to separate the oxides from silica and the silicates is first described, then some of the results obtained are presented as tables.DEVELOPMENT OF FLOTATION REAGENTSThe davidite at Radium Hill is associated with iron and titanium oxides, qu;a,rtz and biotite as replacement deposits in shears. The davidite, rutile,' ilmenite and hematite usually occur in segregations from nut size to masses of several pounds. They are associated as a complexity of...

Jan 1, 1955

By Alberto Bruce

El objetivo del estudio repara sobre el equipo, las condiciones del subsuelo necesarias, y la performance obtenida tras perforar con un medio gaseoso un posible yacimiento de petróleo en la costa Norte Peruana. Como consecuencia de dicho proceso, se muestra que la técnica de perforación es superior a la técnica de perforación con lodo, puesto que logra beneficios como una mayor velocidad de penetración, mayor avance por broca, eliminación de costo de materiales por lodo, etc.

Jul 20, 1955

By F. Mendaña

The characteristics of the igneous and metamorphic bedrock, extra-hard and abrasive, of the Guadarrama Tunnels, a bi-tube project of length 28.4 km without any intermediate attack, are first commented upon. Next, a detailed discussion is given of the most relevant aspects of the performance of the four double shield type TBMs. The experience of this leads to various recommendations to be borne in mind in future designs of TBM having to work in rock of similar characteristics.

Jan 1, 2007

By Alexander May

The Bureau of Mines, in cooperation with the Florida phosphate mining industry, investigated the dewatering of waste phosphatic slimes. Part of this investigation was to determine the electrophoretic mobilities and cation exchange capacities of the slimes. The mobilities and exchange capacities are reported for samples of slimes taken from 15 plants operating in the Florida land-pebble phosphate district that includes Polk,Hillsborough, Manatee, Hardee, and DeSoto Counties. The electrophoretic mobilities determined were all negative, ranging from -0.24 to -1.93 (micrometers per second) per (volt per centimeter). Also reported are frequency distributions of electrophoretic mobilities, electrophoretic mobilities of slime diluted with distilled water and electrophoretic mobilities of sand-slime mixtures. The cation exchange capacities ranged from 17 to 45 milliequivalents per 100 grams of slime solids.

Jan 1, 1975

By William F. Anderson

A series of pile load tests (maintained load tests, constant rate of penetration tests at different rates, and statnamic tests) was carried out on an instrumented model pile installed in clay beds prepared by consolidation of a slurry in a calibration chamber. The total load, shaft resistance and end bearing during the pile load tests were investigated. Following this, alternative methods of deriving the static load-settlement curve from a Statnamic test in clay taking into account damping effects have been proposed. These methods have then been used to interpret a statnamic test on a full size instrumented pile installed in a stiff glacial till.

Jan 1, 2006

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

By N. Loganathan, Tan Boon Tee, Joe O’Carroll, Richard Flanagan

In recent years, tunnelling activities in Singapore have increased considerably with the construction of extensions to the existing sub-surface transport system, a deep tunnel sewerage disposal system, and tunnels for the laying power cables and other utilities. These tunnels are excavated through urban areas, adjacent to high-rise buildings, depressed road structures, beneath other tunnels, and buried services. Earth pressure balance (EPB) tunnel boring machines (TBM) have been used extensively in Singapore with great success. The risk associated with soft ground tunnelling, including tunnelling through Old Alluvium, can be minimized with an understanding of the geology, geotechnical parameters, and the tunnelling-induced behaviour of Old Alluvium (OA The purpose of this paper is to present some design and construction aspects of EPB TBM tunnelling through Old Alluvium.

Jan 1, 2005

By Emilio Cordero Cordero

En los proyectos de excavaciones subterráneas, túneles de obra civil y galerías mineras es necesaria la realización de cálculos para el sostenimiento adecuado para cada situación y comprobar que este cumple los parámetros de seguridad indispensables para garantizar la estabilidad de la excavación en el tiempo. En este sentido, el texto señala el uso de SDT(software) como aplicación informática decuada para el cálculo de sostenimiento en túneles y galerías mineras que suministra una respuesta a las necesidades de proyectistas e ingenieros mineros. Dicho software se basa en cerchas metálicas con capacidad de deslizamiento (perfiles THN), cerchas de perfil HEB, pernos de anclaje y hormigón proyectado en túneles y galerías mineras que utiliza el método “Convergencia – Confinamiento”, procedimiento de referencia en el cálculo y diseño de sostenimiento en excavaciones subterráneas, con las premisas de sección circular, presión sobre el sostenimiento uniforme y el campo de presiones hidrostático.

Jan 1, 2016

By Moussa Wone

The Washington, DC Water and Sewer Authority (WASA) has implemented facility planning for the Anacostia River Projects portion of a program to bring its Combined Sewer System (CSO) into compliance with federal water quality regulations by 2025. The program includes approximately 19 kilometers (12 miles) of deep CSO storage/conveyance and flood relief soft ground tunnels, construction, vortex drop, overflow, maintenance and air release shafts, as well as near surface diversion structures and conveyances. The Project encompasses major technical and non-technical challenges including completion under a federal consent decree schedule, construction within the confines of heavily developed urban areas, difficult ground conditions, major infrastructure crossings, and close coordination with several major public agencies. This paper discusses the planning stage considerations related to the geotechnical investigation program, discusses obstructions that influenced alignment selection, and provides two examples of preliminary estimates of settlement induced ground movement due to the tunnel and shaft construction.

Jan 1, 2008

By M. F. Dunn

During a mine fire or other emergency, it may be desirable to reverse the airflow in order to provide an escapeway or to isolate a fire. Also, in colder areas, the airflow may be reversed to prevent ice buildup. When reversing main mine fans, the mine operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory and field tests of vane axial main mine fans in the 7- to 9-ft diameter size range were conducted to establish forward and reverse performance characteristics under controlled conditions and at typical mine installations. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can be predicted for a family of blade angles and a given hub to tip ratio. Generally, quantity of air is 30 to 65% less in reverse than when operating in the normal forward mode.

Jan 1, 1983

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By N. Aouad

The deployment of large machinery for low cost, bulk surface mine production operations has resulted in high-impact shovel loading operations (HISLO). In extreme cases, shovels load large dump trucks with 100-ton (or more) passes generating high-impact forces under gravity. HISLO generates high-frequency shockwaves that cause severe truck vibrations exposing operators to whole body vibrations (WBV). Current research study in this area has established that the vibration levels affecting the operator?s seat, lower-back, lumbar and cervical regions fall within the extremely uncomfortable zone compared to the ISO 2631 comfort zone. These results pose health threats to truck operators over long-term exposure to these vibrations. In this paper, the authors will examine engineered solutions to mitigate these health threats.

Jan 1, 2011

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931. The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results of other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time each sample was taken will also be reported.

Jan 1, 1932

By Robert E. Green

This Final Report summarizes the results of work accomplished under Contract No. J0215039. It is in an executive overview or executive summary format. The number and description of the various technical reports prepared and submitted is outlined. The essential changes and reasons for the revised program schedule/contract modifications actually enacted in May 1982 are discussed in detail. The evolving mines/deposits list and the accompanying criteria classifications are explained along with the verifications/justifications for adding or deleting specific mines/deposits to the list. Difficulties and problems experienced during the different phases of the project in conjunction with the ensuing remedies are highlighted. The final section of they report is devoted to presenting Davy McKee's suggestions for improvements to future MAS commodity studies. Appendix I is comprised of three of the evolving mines/deposits lists starting with the original RFP list and ending with the final completed list. Appendices II and Ill are tabulated summaries of property data including reserves/resources, assays, production, and operating costs. The figures for the specific mines/deposits are given in "range of values" so as to protect the confidentiality of the individual owners/ operators.

Jan 1, 1983

By Randall M. Wheeler

The purpose of this workshop is to illustrate how computer software can be used to evaluate blast design timing and simulate probable vibration characteristics. The workshop will be presented in two parts. Part I will cover the COMPU-BLAST Blast Design and Timing Analysis Program. Part II will focus on the ALPHA-BUST Vibration Analysis and Waveform Simulation Program. The information presented in the workshop will show how these two programs can be used together to help plan blast designs and aid in the control of vibration effects.

Jan 1, 1991

By Emmanuel Pornillos

Dado que en el Perú, la actividad minera utiliza el minado subterráneo para la explotación de minerales, se revalúa el uso de estos en pasta cementada para el relleno de las labores subterráneas, así como los relaves desaguados para su disposición superficial. En ese sentido, el presente texto señala las experiencias de diseño y operacionales de sistemas múltiples para la aplicación de relaves en superficie y subterráneo en el Perú, de forma que se pueda optimizar la selección de equipamiento y una operación robusta.

Sep 1, 2013

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

I. Domestic Production and Use: In 1981, 13 companies operated 32 primary aluminum reduction plants, with 3 firms accounting for 58% of production, Washington, Oregon, and Montana accounted for 32% of the total production; Texas, Louisiana, and Arkansas 16%; Tennessee, Alabama, South Carolina, and North Carolina 17%; other central and eastern States 35%. Based on published producer prices output of primary metal in 1981 was valued at over $7.5 billion. Aluminum consumption by 25,300 firms was centered in the East Central United States. Packaging accounted for an estimated 30% of domestic consumption in 1981, building 21%, transportation 18%, electrical la%, consumer durables 8%, and other uses 13%

Jan 1, 1982

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004