Search Documents

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By Víctor Gobitz Colchado

Dentro de la industria minera, el objetivo principal del sostenimiento a una excavación subterránea conlleva un soporte de la masa rocosa. Para tal fin, se utiliza la técnica del concreto lanzado (shotcrete), malla metálica y pernos de roca, puesto que ofrecen versatilidad y capacidad portante. En este sentido, el presente texto describe la importancia de dicha técnica a partir de su estructura, filosofía, dimensionamiento, dosificación, rebote, problemas operativos típicos y formas de medición de pago, así como los resultados de campo de una obra proyectada en una mina de la selva central.

Apr 1, 1991

By Jorge Ganoza

El proceso del diseño de circuitos de molienda (SAG) en la planta de flotación de pórfidos de cobre, flotación de minerales polimetálicos o plantas de cianuración y minerales de oro y plata, implica energía que puede variar al procesar minerales blandos o duros. En este sentido, se buscan las operaciones que acepten el tratamiento de minerales duros en los circuitos de molienda y la clasificación del mineral de acuerdo a la dureza.

Sep 1, 2016

By Juver Vélez

El presente trabajo señala los controles QA/QC como herramientas que cuidan el proceso de muestreo en la industria minera, de forma que su resultado determina la calidad de su planeamiento a corto y largo plazo, así como la calidad de trabajo realizado. Para iniciar un correcto control de calidad, se debe ordenar una base de datos, la que debe soportar, archivar y manipular los datos que se obtienen a través de las diferentes actividades desde la exploración a las de operación. En ese sentido, cada dato de muestreo debe ser registrado con todo su precedente, de forma que este valor le dará soporte y el análisis será más confiable y exacto.

Oct 21, 2015

By Peeler P. K

The recent renewal of interest in hydrometallurgical routes for copper production has been brought about by the possible future reliance on mixed ores and lower grade deposits, environmental aspects, and energy considerations.A number of hydrometallurgical processes for the recovery of copper have recently been proposed. Flowsheets are developed for two processes which incorporate several treatment methods being experimentally studied in Australia.In the first process a cupric chloride leach is followed by electrowinning whilst the second is based on the formation of cuprous ions, stabuized by acetonitrile and subsequent disproportionation to cupric ions and metallic copper. For the purpose of comparison, flowsheets were also developed for the Arbiter and Cymet processes.Process economics are estimated for the four processes and the results are discussed in relation to competitive pyrometallurgy. None of the four hydrometallurgical processes, with possible exception of the Cymet process, appears to be competitive with established large scale and newly developed pyrometallurgical processes for chalcopyrite.However, because the economics of the individual hydrometallurgical processes depend strongly on specific conditions, a "tailored" process may be competitive with pyrometallurgy in particular circumstances.

Jan 1, 1977

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By Jesús Vizcarra, Arnaldo Ruiz, Luis Torres

Las características físicas del macizo rocoso son muy importantes en las labores mineras subterráneas y superficiales. La meteorización es un proceso físico, químico y orgánico que modifica la composición de la roca y tiene como resultado la alteración de la misma. En las labores mineras subterráneas y superficiales, el agua afecta al macizo rocoso, por lo que hallaremos el índice de durabilidad de la roca y mineral a través del ensayo del slake (abrasividad y desmoronamiento). El presente trabajo de investigación incluye las generalidades de la Minera Huínac S.A., los objetivos, equipos utilizados, base teórica, parte experimental y los resultados obtenidos.

Sep 20, 2019

By Eduardo Socolich

El presente texto señala el desarrollo de generadores de burbujas y la forma cómo debe introducirse en la columna, el requerimiento mínimo de aire y otros parámetros. En ese sentido, el air hold-up o volumen del aire dentro de la columna a cualquier tiempo de Cuajone fue objeto de estudio y de pruebas en laboratorio y planta.

Nov 1, 1988

By L G. B Wadley

The Australian gold industry has made large steps forward in the last few years. This progress has been driven by improvements in mining and processing technology, the high price of gold and by a favourable legislative, political and taxation environment. This paper concentrates on improvements in gold project development, process engineering and technology as seen by BHP Engineering, Perth, Australia. The paper describes technical aspects of successful gold project development including metallurgical test work, feasibility studies, choice of process flow sheet (gravity, heap leach, carbon in pulp (CIP), carbon in leach (CIL) or other routes). It sets out our views on plant design, plant construction, procurement and project management. A case study for a small plant recently completed in the Philippines is presented as a solution to the problems often encountered in treating quartz vein gold deposits.

Jan 1, 1990

By Russell B. Dix

Laboratory column leach tests are used routinely to evaluate gold and silver ores for heap leaching. The tests are fairly straightforward. The ore to be tested is placed into an appropriately sized leach column. Then an alkaline cyanide solution is applied to the ore and the effluent solutions are collected. The effluent solutions are then put through a column of activated carbon to recover the gold and silver in solution. Zinc precipitation may also be used for silver ores or if the ore contains a significant amount of soluble silver in addition to gold. The length of the leach time in the tests is mainly a function of how quickly the precious metals are recovered from the ore. At the completion of the tests, the tailings are assayed and the recoveries determined from the calculated head grades. The amount of ore to be used for a test is partly a function of its crushed size. The coarser the size, the larger the sample size for the column. A typical small-scale laboratory column test on ore crushed to -12 mm (-0.5 in.) would usually be conducted in a 100- to 150-mm-diam (4- to 6-in.-diam) column 2 m (6.6 ft) in height, containing about 20 to 45 kg (44 to 99 lb) of ore. A comparable test on the same ore crushed to 50 mm (2 in.) would be conducted in a 200- to 300-mm-diam (8- to 12-in.-diam) col¬umn 2 m (6.6 ft) in height, containing about 80 to 200 kg (176 to 441 lb) of ore. Larger-scale tests can be run by increasing the column heights and diameters. Conducting larger-scale tests results in increased costs for sample procurement, preparation, and running of the tests. The additional data obtained from

Jan 1, 1989

By Alberto Giles P

El presente texto señala el sistema de tolva de almacenamiento intermedio en el yacimiento minero, donde los volquetes depositan sus cargas y desde este espacio, el material se descarga a los trenes. En este sentido, la tolva fue construída y diseñada en Toquepala, adquiriendo un sistema de carguío más eficiente y aumentando la productividad de la mina.

Oct 14, 1980

By Joël P. T. Kapusta

Although Peirce-Smith converting remains the workhorse in matte converting, the copper and nickel industries are still confronted with production hindrances such as tuyere blockage, excessive refractory wear and limits in the oxygen enrichment levels of the blast air. The knowledge acquired on high-pressure gas injection technology as well as the invention of the concentric tuyere for steelmaking led to the development of the Air Liquide Shrouded Injector (ALSI) technology for copper and nickel converting. Following a technology demonstration in 1997-98 with four shrouded injectors installed in a Peirce-Smith converter, Falconbridge Limited implemented ALSI Technology on a commercial scale in May 1999 as an integral part of its new Slag Make Converter at Sudbury, Ontario, Canada. The paper presents the various aspects of commissioning ALSI Technology, as well as the operating changes and injector design modifications over the five years the shrouded injectors have been in operation.

Jan 1, 2005

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

Working in thick coal seams presents many problems, included in these is obtaining the maximum recovery of coal under safe working conditions. In order to obtain maximum extraction it is important to understand the behaviour of pillars left for support purposes. However it is not always the practice to maintain pillar stability it is often required to design for pillar failure. The greatest hazard of pillar mining is uncontrolled pillar collapse. Many major and relatively minor collapses of pillar workings have been recorded in the history of mining. Notable among the collapses was that at Coalbrook Colliery in South Africa in 1960 (Bryan et al 1964). This led to recommendations on the design of bard and pillar workings in South Africa. (Salamon 1967) These design recommendations were based on the statistical analysis of stable and unstable pillar workings and introduced the concept of probability of pillar failure and safety factor. On the basis of this study a safety factor of 1.6 was prescribed for production panels in South Africa. A general review of pillar design procedures, reveals that a new phase of reinterpretation and modification is in progress. This takes into account for instance the effect method of working, whether by conventional drilling and blasting or continuous miner, has on coal pillar strength, and the necessity to review the methods for increasing depth of working. Also, as more is being understood about overall rock mass properties and advanced computer modelling techniques become more readily available, the mine planning engineer is faced with numerous approaches to pillar design.

Jan 1, 1989

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

El presente texto revisa algunos aspectos del programa de salud ocupacional en las compañías mineras aplicados en el ambiente de trabajo, la explotación de minas y el desarrollo de su control. Primeramente, se describe los riesgos encontrados en las condiciones de trabajo como la composición química del ambiente, la inhalación de polvo y gases en el aire del subsuelo. Como segundo punto, refiere las condiciones de seguridad de la mina, donde se sugiere que el personal de seguridad sea el más idóneo para la dirección del programa de seguridad. Para ello, es importante su capacitación en técnicas de evaluación y control, así como la participación de los médicos de la compañía. Por último, se mencionan algunas medidas de control en las minas, tales como el uso de equipos detectores de gases que determinen los contaminantes sólidos y gaseosos, la compra de un equipo detector de Cu, lámpara de seguridad y la instalación de un equipo de laboratorio químico adecuado,etc.

Jul 20, 1957

By AIME AIME

THE list of deaths during the year 1906 comprises the following names, the figures in parentheses indicating the year in which the persons named were elected to membership Members and Associates.-Arthur Vaughan Abbott (1882), William Anderson Akers (1889), R. Scott Allen (1905), George H. Arlett (1900), Thomas Septimus Austin (1883), Thomas T. Baker (1887), William Tittley Batchelor (1902), Charles Lowthian Bell (1897), Edgar Vallentine Bensusan (1892), George Lothrop Bradley (1874), Ernst Elmer Breisch (1896), Horace F. Brown (1895), James A. Burden (1876), Alexander B. Coxe (1880), George A. Crocker (1879), Albert W. Fiero (1886),

Jul 1, 1907

By Li Keqiang

This paper discusses the pile foundation of tall buildings in Shenzhen region. For 156 constructed tall buildings exceeding 18 storeys, about 86. 5 per cent of the sum. The two main types of foundation used are the semi?machine?bored/slurry drilled cast?in?situ pile and the excavation pile (hand ?dug caisson). The engineering geologiical condition in Shenzhen was analysed. In general, the bed rock level is not too deep. It belongs to hard rock, but the geologic structure is more complex and the tectonic fissures is plenty. According to experiences of the researches, tests, designs and constructions of pile foundation, we present the basic design principle of pile foundations for tall buildings as follows; (1) pile strength control to select the pile type and to choice the cross sectional dimen­sions, must be in compliance with the strength of the pile. (2) bearing stratum strongly weathered, moderartely weathered and slightly weathered rock may be used as the bearing stratum. (3) bearing pile bored /drilled cast-in-situ pile designed as an end bearing pile. (4) friction pile precast concrete pile, prestressed concrete tubular pile and driven cast-in-situ pile designe as a friction pile. In case, pile design is in compliance with these principles, it may be safe, economical and reasonable.

Jan 1, 1991

By Mario Samamé Boggio

El presente texto describe algunos aspectos de la inversión extranjera en tres períodos: fines del siglo XIX, la primera mitad del siglo XX y segunda mitad del siglo XX. Dentro de lo quince casos analizados se halló que 5 empresas son iguales: Northern, Southem, Santander, Santa Luisa y Madrigal; 4 empresas se han "peruanizado" total o parcialmente: Caylloma, Ticapampa (Alianza), Lampa (Minsur) y Ruaron, 3 empresas se han agotado aparentemente: Santo Domingo, Salinas y Minas Ragra, 1 yacimiento revertió al Estado y fue desarrollado por Minero Perú: Cerro Verde; y 2 empresas fueron expropiadas y estatizadas: Cerro de Pasco Corporation y Marcona. En todos los casos no hubo descubrimiento del yacimiento por el inversionista, quien compró las concesiones y denuncios, con excepción de Marcona que estuvo explorado y desarrollado y fue contratado para su explotación.

Mar 1, 1982

By Jhon Melo

Los “softwares de aplicación” como herramientas en la exploración geológica, generan importante información geográfica sobre el área a estudiar, así como la cartografía y la toma de muestras en laboratorio. En ese sentido, el presente texto señala el manejo adecuado de dichas herramientas a través del uso de una base de datos, donde existe una estructura basada en el software (VISUAL FOXPRO, PARADOX, etc) y asi ejecutarla mediante una aplicación gráfica que permita tener una representación de lo estudiado como ocurre en un muestreo geoquímico.

May 25, 1998