Search Documents

By K J. F Logan, P W. Leaman, B A. Tucker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Nam San copper-gold deposit was discovered in 2011 and is a likely blind extension of the Permian age Phu Kham structurally deformed porphyry/skarn copper-gold deposit.The Nam San mineralisation is hosted within a dominantly sericite altered schist unit located to the north of the current Phu Kham open pit operation and is overthrust by an allochthonous barren cover sequence of limestone, granite and sandstone. Reinterpretation of the Phu Kham geology developed the concept of a possible telescoped porphyry copper-gold system at depth. Initial drilling intersected remobilised copper mineralisation in a basal conglomerate, confirming the concept. A reconnaissance vector array induced polarisation (IP) survey identified a deep chargeability anomaly from which a drilling target was developed from 3D inversion modelling of a detailed follow up dipole-pole-dipole anomaly. Drilling of the chargeability anomaly intersected the blind Nam San copper-gold mineralisation beneath the thrusted cover sequence.The key discovery parameters are the result of an integrated exploration program that included reinterpretation of the local stratigraphy, which developed the concept of a deep blind orebody, IP surveys capable of penetrating through the barren cover and a commitment to a deep directional drilling program to test these concepts and targets. The inferred resource remains open at depth, and further assessment will most likely be through underground development.CITATION:Leaman, P W, Tucker, B A and Logan, K J F, 2015. The discovery of the Nam San copper-gold deposit, Phu Kham, Laos, in Proceedings PACRIM 2015 Congress, pp 515–520 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By G Baiden

The removal of rock blockages in mining operations has long been a risky undertaking, especially in high overhead conditions. Moreover, the assessment of where to put charges and the placement of them has been difficult due to the lack of visibility and safe access to the area. Traditionally, wedging long poles with explosives on them to keep the operator at a relatively safe distance has been the tried and true method of attempting to remove the blockages. Unfortunately, this is not a perfect system as it usually takes several attempts to remove the blockage. Each successive attempt results in even more dangerous conditions for workers and/or damage to the mine due to the successively larger amounts of explosives used until the hang-up finally comes down.Over the years, different ideas have been proposed to improve this process and reduce the inherent safety risks. Some of the technologies that have been trialled include projectiles fired at the hang-up; large, cumbersome arms; and massive amounts of explosives, each of which come with their own inherent safety risks that result in dangerous situations for miners and the mine.After gaining a thorough understanding of the process, Penguin Automated Systems Inc has developed a robotic system that is capable of working in a rock blockage safely. The idea combines the latest in telerobotics technology with 3D scanning and underground geospatial positioning. The hang-up removal is performed by scanning the inside of the hang-up to rapidly develop a geospatially placed 3D model for the operator to use. The 3D model is detailed enough that the operator can attempt to pick the ‘keystone’. A blasting engineer or the operator can then determine the exact position where the explosive charge should be placed in the 3D model and thus at the actual hang-up. The operator, controlling the robotic arm, uses the 3D virtual reality model of the robot system and the actual drawpoint information model to display the location information, the arm can then reach into the hang-up to position the charge using the kinematic model of the robot system. The 3D model is used to provide views inside the hang-up so that the operator can move the arm safely and precisely. This process allows the operator to place the charge (using the 3D representation of the drawpoint) from a long distance away. As the process continues, the end of the arm drills the rock and precisely loads the explosives. The robot then returns the blasting cable to the command station, which is located in a truck at a safe distance from the blockage.This paper will review the development of the system and present the results to date.CITATION:Baiden, G, 2016. Robotic hang-up assessment and removal of rock blockages in mining operations using virtual reality for safety, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 745–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By Richard Peaker, Jens Lichter, Alexander V. Potapov

The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism. This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.

Jan 1, 2007

By Trevor Yeomans, David Yaschyshyn

"Placer Dome (CLA) operates the 90-year-old Dome Mine, in South Porcupine, Ontario.The milling operation currently processes 5 million tons of ore per year, from both the underground and Open pit mining operations, producing 320 000 ounces. The milling process is conventional crushing and grinding, with gold recovery by gravity followed by leach/CIP.Cyanide tailings are impounded in a large (325 ha) tailings area where cyanide is allowed to degrade naturally. Effluent is discharged seasonally during the summer and early fall months to maintain site water balance. Pond water is reclaimed for sole use within the mill process.In 1995, an Effluent Treatment Plant (ETP) was constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO S02/Air cyanide destruction module was added.During this time period, the treated effluent often failed toxicity tests required by the Ontario MISA Regulation, even though effluent chemical parameters were below permit limits. Two studies identified ammonia as the toxicant to Rainbow Trout, and free copper as the toxicant to Daphnia magna.From a literature study, and contacts within the Ontario Mining Association, the use of chelation as a final end of pipe treatment step to render any remaining free copper and metal fractions biologically unavailable was considered. Lab and plant scale tests followed.During the 1999 ETP operating season, the addition of the chelant EDTA (ethylene-diamine-tetraacetic-acid) commenced. To date discharged effluent has passed all toxicity tests.The paper will review the effluent treatment history, current effluent treatment plant operation, and detail the use of EDTA for successful toxicity control.History of Tailings Deposition, and Effluent Treatment From 1910 to 1995Over it’s ninety years of operation, the Dome Mine milling circuit has changed from the original 1910 stamp-mill mercury plant, to today’s modem 14 000 ton per day automated gravity and Carbon in Pulp based plant.By the 19803, a modern mill was operating on mainly underground mined ore. The plant was operating at some 3 800 tons per day, using fairly conventional processing routes.The number 4 tailings dam was being used for tailing’s deposition.All effluent treatment was by natural degradation of cyanide. Discharge was from decanting type structures during the summer months only, maximizing the use of natural degradation no tailings effluent was recycled for Mill use."

Jan 1, 2001

The coalmining industry in most countries has, at various times, suddenly been confronted with a decrease in demand for coal. Readjustments made to reduce productive capacity to match the reduced demand for coal have often resulted in hardship to mineworkers, loss of capital investment to mineowners and loss of coal reserves. The consequences of the methods of readjustment adopted in the past have contributed to the low esteem in which coalmining has come to be regarded by a large section of the gel).eral public in many countries.Four sections of the coalmining industry, representing different periods of time, different countries, and different methods of industrial organisation have been examined:Great Britain and the U.S.A. during the inter war years, the post war European Coal and Steel Community, and post war Great Britain under the National Coal Board. An assessment has been made of the methods adopted in each case to reduce productive capacity to match a reduced demand for coal. Finally the fundamentals of the problem-as it affects the coalmining industry of any country-are considered, and possible solutions put forward.During the 1950's, surplus productive capacity was a problem in many coalmining countries, including Australia and New Zealand. As a rule no techniques are developed beforehand to solve problems introduced by a sudden decrease in demand for coal. The situation is usually tackled by a series of short term decisions based on expediency, which often in the long run only aggravate the problem.

Jan 1, 1961

By G. H. Sedahmed, S. A. Nosier, M. H. Abdel-Aziz, A. A. Mubarak, M. A. El-Naggar, E. G. Abdel-Aziz

The performance of a rotating fixed bed reactor in recovering copper from industrial waste solutions by cementation is studied under various conditions. The rotating fixed bed is made of stacked woven steel screens to take advantage of two features of screens: the ability to present large area per unit volume and their ability to promote high turbulence. Variables studied are initial CuSO4 concentration, bed rotation speed, mesh number of the screens and bed thickness. The presence of baffles was found to increase the rate of cementation. The data were correlated by a dimensionless mass transfer correlation suitable for the design and operation of large scale cementation reactors.

By G. H. Sedahmed, S. A. Nosier, M. H. Abdel-Aziz, A. A. Mubarak, M. A. El-Naggar, E. G. Abdel-Aziz

The performance of a rotating fixed bed reactor in recovering copper from industrial waste solutions by cementation is studied under various conditions. The rotating fixed bed is made of stacked woven steel screens to take advantage of two features of screens: the ability to present large area per unit volume and their ability to promote high turbulence. Variables studied are initial CuSO4 concentration, bed rotation speed, mesh number of the screens and bed thickness. The presence of baffles was found to increase the rate of cementation. The data were correlated by a dimensionless mass transfer correlation suitable for the design and operation of large scale cementation reactors.

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

By B Hiebl, J Martens, L Petzold

A research team at the Iron and Steelmaking department at Primetals Technologies has established new upgrading measures for improving the efficiency of the beneficiation process in ironmaking plants, relying largely on pre-existing equipment. After the upgrade, the iron content in the final iron ore concentrate was shown to be significantly higher. Remarkably, the costs for employing the respective measures are surprisingly low.This case study is based on a Kazakh iron and steel producer, whose beneficiation process is currently generating a magnetite concentrate with a final iron content of 65.65 per cent. The study shows that the implementation of Primetals Technologies’ intelligent modification measures to the current beneficiation process, the realisation of more effective dewatering, and the utilisation of an innovative binder lead to an increased iron content in the resulting pellets, reaching a concentration of 69.17 per cent (iron ore concentrate) and 66.5 per cent (pellets).The current operation consists of three closed circuit grinding stages, four stages of low intensity magnetic separation, vacuum disc filters and straight-grate pelletising. By dividing the slurry after the second stage of grinding and the third stage of low intensity magnetic separation, it is possible to divert the more iron-rich fines before they would enter the third grinding stage and the fourth stage of magnetic separation. This then reduces the load on the existing third stage ball mill. Afterwards, the ground material is treated in an additional low intensity magnetic separator and mixed with the previously diverted fraction of the fines. An improved filtration procedure, combined with the application of a highly sophisticated binder, further reduces the amount of additives needed, so that a genuine direct reduced (DR)-grade iron concentrate is produced as a result.All laboratory, pilot and pelletising test work was executed at Primetals Technologies’ laboratories in Austria.CITATION:Martens, J, Petzold, L and Hiebl, B, 2017. Enabling iron ore concentrate for the production of direct reduced iron with pre-existing beneficiation lines, in Proceedings Iron Ore 2017, pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.

By Qingming Feng, Bo Huang, Dongbo An, Jinhong Zhang

A study of the application of mine tailings as precast construction materials through alkali activation has been carried out, focusing on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. Firstly, the effect of temperature on the alkali activation of mine tailings was studied. Secondly, the impact of additives, i.e., calcium hydroxide and aluminum oxide, on the compressive strength of samples was investigated. Thirdly, the impact of forming pressure on sample strength was studied. Test results showed that unconfined compressive strength (UCS) of 40 MPa was achieved with the geopolymerization products through optimization. Finally, to elucidate the geopolymerization mechanism of mine tailings, microscopic and spectroscopic techniques including SEM/EDX, XRD, and FTIR spectroscopy were used to investigate the microstructure and the elemental and phase composition of the geopolymerization products. The findings of the present work provide a practical method for applying mine tailings as precast construction materials through alkali activation.

By Taehong Kim, Carl Pannuti, Nikolas Sokol, Walter Herrick

BACKGROUND This paper discusses work performed as part the rehabilitation of the gravity flow section of the New Croton Aqueduct (NCA) during an approximately two year period between 2004 and 2006. The goal of the project was to restore the gravity flow section of the NCA to optimal operating condition, extending the lifespan of this significant water supply for the New York City metropolitan area. Rehabilitation of the NCA was purposely scheduled before the completion of the new NCA Water Treatment Plant now under construction (Figure 1). The NCA is a 3.73 to 4.34 m (12.25 to 14.25 ft) diameter brick-lined circular andhorseshoe shaped water tunnel constructed between 1885 and 1891. The NCA conveys water for approximately 50 km (31 miles) by gravity and pressurized flow from the New Croton Reservoir in Westchester County, NY to distribution and reservoir points along its alignment, terminating at a distribution station at 135th Street and Convent Avenue in Manhattan, NY. Prominent features of the NCA include a large intake facility at New Croton Reservoir, 38.6 km (24 miles) of gravity flow horseshoe shaped aqueduct, 11.3 km (7 miles) of pressurized flow circular aqueduct, 2 siphons, and 36 open shafts and headhouse chambers which are used as sampling, access and blow-off locations. Until a partial inspection in 1982, the NCA had flowed continuously since its completion nearly 100 years prior. Flow tests have confirmed that the NCA can convey up to 12.7 m3/s (290 mgd) (Figure 2). Cover depths of NCA vary considerably, ranging from a few to hundreds of meters, typically of hard rock. Primarily mined using means conventional for the late1800s, construction of the NCA also employed cut and cover methods in several low-lying sections of the alignment, totaling approximately 1.6 km (1 mile). The NCA crosses through numerous lithologic changes, fault/shear zones and under several significant water bodies including the Pocantico, Saw Mill and Harlem Rivers and the Tarrytown Reservoir. The NCA passes under the Harlem River as a siphon at a depth of approximately 122 m (400 ft) below grade (Figure 3). Soon after construction the Aqueduct Commission Reports on the New Croton Aqueduct documented prominent defects such as large voids behind the lining. More recently, large-scale inspections of the gravity flow section performed during the 1990sand a 2004 inspection of portions of the pressurized sections of the NCA have revealed additional defects such as open and/or deteriorated masonry joints/cracks, leaks ranging from trickles to several liters per minute into and out of the NCA, missing bricks, formed openings, and in one place, a rupture through the liner with discernable

Jan 1, 2007

By F. A. Guo

Ultrafine-grained surface layers were obtained by surface mechanical attrition treatment (SMAT) in copper and titanium samples. The thermal properties of the deformed layers were characterized using a scanning thermal microscopy (SThM) that allows thermal conductivity to be mapped down to the submicrometer scale. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a powerful tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Jan 1, 2006

In order to deliver a quality shotcrete and concrete product underground for the extensions to the Cullinan Diamond Mine operations it was decided to develop a new, simpler concrete product to meet underground support requirements. The aim was to develop a concrete product that not only reduced costs but also met the performance criteria of the current range of concrete products used on Cullinan Diamond Mine, a 25, 45 and 60 MPa concrete and a fibre reinforced wet shotcrete. The concrete product batching and delivery system was to be from surface as opposed to the current underground batching systems. The operational principle was to include an automated surface batching plant with delivery of the concrete product to a borehole containing suspended pipelines delivering to an underground storage facility from where the product is delivered to the working area by further pumping or agicars. Keywords: concrete, shotcrete, full flow, frictional loss, pipeline transport, positive displacment pump

Jan 1, 2006

MR. W. E. WAINWRIGHT occupied the chair, and in introducing the lecturer said, on account of the absence of the vice-president, it fell to his lot to introduce the lecturer. Mr. Tennberg, he said, was visiting Australia, and those present might wonder who he was.He understood that the lecturer w~s a reputable practising geophysicist, associated with a reputable company! It was rather desirable perhaps to say that the Institute had made some inquiries with regard to his status. Geophysics was a comparatively newscience, and had suffered several hard knocks in Australia and elsewhere. Most of those knocks had been the result of undue optimism of a number of people who did not understand what they were talking about. It had been claimed that geophysics was a...

Jan 1, 1930