Search Documents

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By Joseph A. DeCarlo

The rapid growth of the organic chemical industry in the United States and abroad has focused attention on the future raw-material sources for this important industry. Chemical products are essential to modern civilization; and millions of tons of organic chemicals are used annually, ranging from basic raw materials to finished chemical products such as drugs, cosmetics, and soaps. Hundreds of chemical products are made directly or indirectly from coal, but in this report "coal chemicals" will be limited to crude tar, crud light oil, and ammonia recovered in the high-temperature carbonization of bituminous coal and the important principal products obtained by processing these materials. Specifically these include benzene} toluene, xylene, naphthalene, creosote oil, tar acid oil, pitch, and ammonium sulfate. Therefore the term "coal chemicals", wherever used in this report, includes only these products and does not include the secondary or intermediate products such as styrene, synthetic phenol, aniline, phthalic anhydride, or finished products made from these, such as synthetic rubber, plastics, and dyes. The United States leads the world in production and consumption of coal chemicals. In the past five years nearly one-fourth of the total output of coal-tar crudes in the world was produced in the United States. Consumption of some of the more important products derived from these crudes such as benzene, toluene, xylene, and naphthalene, however, ranged from about one-third to one-half of the world total because of imports and production of benzene, toluene, and xylene from petroleum. The synthetic organic chemical industry of the United States was established during World War I on chemical raw materials obtained by the high-temperature carbonization of bituminous coal but this source of supply currently furnishes less than 40 percent. More than 60 percent of the chemical raw materials used to produce organic and inorganic chemical is supplied by the petroleum industry and production of petrochemicals is rising rapidly.

Jan 1, 1960

The coal-bearing regions of Colorado cover approximately 29,600 square miles, which is 28.4 percent of the state's total area. The most important coal-bearing regions are located in the north western and west-central parts of Colorado. Coal resources vary from lignite to anthracite. More than 70 percent are bituminous; 23 percent subbituminous; 5 percent lignite; and less than 1 percent anthracite. The state's coal reserves total about 17.2 billion tons, 3.5 percent of national reserves. Approximately 8.8 million acres of coal rights in the state are owned by the Federal Government; on about 72percent of this land, the Federal Government controls both the coal and the surface rights. It is estimated that approximately 4.2 billion tons of coal reserves are under federal ownership in Colorado. Permitted acreage of mines in Colorado ranges from 40 to 13,114 acres. Differences in elevation create many climatic zones in Colorado. Local annual precipitation can average less than eight inches in some areas in extreme western Colorado to more than 30 inches in certain mountainous areas. Generally, precipitation rates are low at most mine sites, making revegetation difficult. Colorado gained primacy when its regulatory program was conditionally approved December 15,1980. The Abandoned Mine Land Program was approved June 11, 1982.

Jan 1, 1992

By M Baker

Biodiversity offsets are conservation actions intended to compensate for the residual, unavoidable harm to biodiversity caused by development projects. The use of biodiversity offsets in the context of mining has significant potential for enabling mining to take place in areas with biodiversity values, where it would not otherwise be possible to meet the relevant legal tests under the Resource Management Act 1991, and potentially the Conservation Act 1987. This paper looks at the concept of biodiversity offsets (and environmental compensation generally) both in New Zealand and internationally, and considers how lessons learned overseas may be adapted for this country. In New Zealand the practice of biodiversity offsets and environmental compensation is ad hoc and variable. The challenge with biodiversity offsets is to establish a transparent and coherent means of identifying the overall priorities and objectives of adopting such an approach, as well as how the relevant values are measured and protected. Establishing a methodology for quantifying biodiversity value, and the need for clear policy guidelines on biodiversity offsets are identified as key areas in need of wider discussion.

Jan 1, 2007

By Yum Xiaoquan, Turgut Yalcin

"A laboratory study was carried out to determine the potential role and effect of ultrasonic irradiation in the flotation of a Sudbury copper-nickel sulphide ore. The use of ultrasound was tested separately at the pulp preconditioning, collector conditioning and flotation stages. While no significant benefits were evident in the latter two cases, ultrasonic preconditioning of pulp improved the grade-recovery performance and had the prospect of reducing reagent consumption rates. Tests were conducted on both the normal and oxidized ore samples, and several variables were investigated, including ultrasound frequency (25 kHz and 45 kHz), ultrasonic power (up to 1.6 W/cm2), duration of ultrasonic treatment (up to 60 minutes), and the intensity of pulp agitation employed during the application of ultrasound. Ultrasound frequency of 25 kHz and duration of 15 minutes yielded satisfactory results. Changes were found to occur in the temperature, pH and Eh of the pulp during ultrasonic processing. The favorable effects of ultrasound observed in this study were attributed primarily to its surface cleaning capability.INTRODUCTIONThe use of ultrasound for the surface cleaning of objects is well known. Ore flotation is based essentially on the surface properties of minerals, and hence stands to benefit from ultrasonic treatment which may help restore mineral surface characteristics that might have been lost or modified through oxidation, etc. Expected outcomes of this method of treatment include improved flotation kinetics, higher recovery, better selectivity, and savings in reagent consumption, as has been demonstrated by various researchers (Aldrich and Feng 1999, Celik 1989, Ozkan 2002, Letmathe et al. 2002, Nicol et al. 1986)."

Jan 1, 2005

By Andrea Koschinsky, Peter E. Halbach, Margret Halbach, Andreas Jahn

"Ferromanganese crusts contain hydrous Mn and Fe oxides as main metal compounds together with some economically interesting minor elements such as Co, Ni, Ti and Cu and trace metals such as Mo, W, Nb, Te, Ga, Pt, and REEs. Some of these metals or semimetals have a great future potential as innovative high-technology constituents. All of them are highly enriched in the crusts compared to seawater composition.The Mn in the crusts mainly originates from the O2 - minimum zone in the oceanic water column. The agent for Mn2+ oxidation is dissolved oxygen, transported upwards from colder deep water layers by turbulent eddy diffusion. The Mn itself descends from surface waters and is carried down to the O2-minimum zone by fecal pellet transport. In contrast, Fe is mainly supplied from carbonate dissolution of planktonic skeletons in the water column. These relationships result in the fact that the oceanic water depth strongly controls the metal composition of ferromanganese crusts: the Mn - group metals are more enriched in shallower water, whereas the concentration of the Fe - group metals increase with water depth. The REEs play a very important role with regard to the trace metal composition of the crusts: their concentrations increase with water depth mainly controlled by a decreasing Mn/Fe ratio.In seawater, REEs occur as carbonate complexes; preferably, the light rare earth elements (LREEs) form REECO3 +(aq) and the heavy Rare Earth Elements (HREEs) REE(CO3)2 (aq) complexes. The REEs are transition metals, their 6s orbital of the outermost shell is filled before the filling of lower 4f electron shells is completed, thus the configuration of the valence electrons is similar in all the REEs, and all REEs exhibit similar chemical behavior and exist, dominantly, as 3+ cations. The ionic radius decreases progressively from La3+ (1.18 Å) to Lu3+ (0.97 Å), this phenomenon is called "lanthanide contraction". Due to the fact that REEs in seawater form cationic and anionic carbonate complexes, the two main hydrogenetic constituents, hydrous !-MnO2 and Fe-oxyhydroxide, fractionate the group of REEs by surface absorption processes. According to the pHZPC-concept the ?- MnO2 phase has an electronegative surface, and Fe-oxyhydroxide a slightly positive surface charge at seawater pH. These relationships are the main reason for the observed REEs fractionation."

Sep 1, 2014

By Jan E. Nesset, Antonio DiFeo, James A. Finch, Jose Hernandez-Aguilar, Cesar O. Gomez

"The gas dispersion measurement sensors and methodology developed by the mineral processing group at McGill University have to-date been employed at a number of plants in Canada, Australia, the U.S., South Africa and South America. In some cases the measurements have been directly linked with metallurgical performance while in others the gas dispersion surveys on their own have proved very useful in understanding the behaviour of the flotation cells. In addition to reviewing the current state of the gas dispersion measurement technology, the paper will present a series of case studies from the various plants and will show how this technology brings a remarkable new level of understanding to flotation behaviour. The influence of the bubble size distribution on recovery and grade are emphasized in the paper.INTRODUCTIONBackgroundThe advent of new sensors to characterize gas dispersion parameters in flotation cells is a development that is long overdue. While the chemistry of flotation has been studied since the early 1900’s, it is only now that the significance of bubble size distribution, gas rate and gas holdup can be meaningfully measured in-plant with robust and precise sensors. Early researchers, like T.A. Rickard (1916) recognized the importance of understanding the role of air and bubbles in flotation when he wrote in 1916 “we know that the key to the flotation process is to be found not in the oil, the acid, or the apparatus, but in the bubbles. The man who understands the mystery of a soap bubble has mastered the chief mystery of flotation”. In his 1999 review paper on The Froth Flotation Century D.W. Fuerstenau laments the fact that due to their “inert nature”, bubbles have never received their due attention from researchers who tended to focus on the chemical, physical, surface and colloidal aspects, rather than the physics of the process. It is perhaps fitting that now, 100 years after the inception of industrial flotation practice at Broken Hill, Australia, researchers and industry have turned their attention toward the importance of truly understanding the role of bubbles in flotation."

Jan 1, 2005

By R. S. Montgomery

Laboratory experiments simulating rock drilling were conducted on a number of commercial grades of tungsten carbide in order to determine their wear rates when they are used as inserts in percussive rock drill bits. The test rock was Barre granite and tests were made at conditions similar to those of the carbide buttons near the periphery of a large, down-hole, button bit. In addition, some wear rate measurements were made at a low blow energy. Wear rates of these carbide buttons were an extremely sensitive function of their cobalt contents and hardnesses and were proportional to e-°.57Hup to a hardness of about 91 RA. The point of minimum wear rate, which occurs at about 92 RA, corresponds to the point of maximum compressive strength. Modern percussive rock drill bits have inserts of cemented tungsten carbide on their wear faces. These inserts have drastically reduced bit wear in comparison to that of earlier all steel bits. The most common cemented carbide grade used in percussive rock drill bits contains about ten weight percent cobalt, although grades containing more or less cobalt are also used. Contrary to the case with carbide in metal-cutting tools, alloying materials are rarely used in mining grades. There are a number of designs of rock bits in current use. The most common form is an X bit which has four chisel-form radial wings. The button bit is another important design and one which has been recently developed. This design uses a flat steel face studded with relatively small hemispherically tipped carbide buttons. These types are illustrated in Fig. 1. Studies have been made of the sliding wear of cemented tungsten carbide on rock 1-4 and multiple-impact fracture', 5-6, b~t there has been comparatively little published on the percussive wear of this material although the wear of the impact face is the most important. There is some available data on the rate of dulling of rock bit inserts in actual drilling 7 but no laboratory studies. Sliding wear studies are useful for understanding the wear of coal and mineral cutting tools and gauge wear of percussive drill bits. but the

Jan 1, 1970

By A. Zeni, S. L. Bessinger, T. A. Palm

San Juan Coal Company (SJCC) operates an underground coal mine near Farmington, New Mexico. Continuous miners and a longwall produce 7-8 million tons per year. The coal seam at SJCC has tested to have a propensity for spontaneous combustion. As such, during feasibility for this project, it was elected to utilize a bleederless ventilation system on the longwall. Three-entry gateroads are developed, and the longwall gob is sealed as mining progresses. SJCC utilizes a nitrogen injection system to continuously inertize the gob. In 2004, the mine was nearing completion of its first longwall district. The next district would contain longer panels (up to 12,500 feet). Due to the liberation of methane, and to a lesser extent hydrogen sulfide, a typical wrap-around ventilation system would not be appropriate. Not only would gas concentrations likely be challenging, but the overall ventilating pressure in the mine would have to be increased beyond limits established to mitigate the potential for spontaneous combustion. Given the above-described operating constraints, SJCC determined a need for a small ventilation shaft in the back (longwall setup area) of the next district that would draw adequate air past the longwall seals to maintain low gas levels and permit the required regulatory inspections to occur. Extensive ventilation modeling and gas desorption testing indicated that the shaft would be required to handle a volume of air ranging from 40,000 cfm to as high as 185,000 cfm. This large range is driven by the position of the longwall face with respect to the shaft and the effectiveness of the SJCC degasification program (SJCC uses vertical gob vent boreholes and horizontal in-seam methods). Ventilation simulations determined an appropriate diameter for the 350-ft-deep shaft to be 5 feet. Having determined shaft size, the next decision related to the method of shaft construction. Conventional shaft sinking was ruled out, due to the small diameter. Raise boring was an attractive option but had two drawbacks: (1) development crews would reach the bottom of the shaft just a few weeks before longwall startup, leaving a compressed timeframe to install the shaft, and (2) raiseboring requires additional underground entries to be developed to stow the project’s cuttings. While raiseboring remained a viable option, the problems associated with it led SJCC to also investigate blind drilling.

Jan 1, 2006

The Department of Mineral Resources is the lead agency in mine site environment management and control inNew South Wales. The Department introduced a Mining, Rehabilitation and Environmental Management Plan (MREMP) process several years ago in order to integrate the activities of other government agencies who may have a material interest at the mine site. The MREMP process has resulted in a spirit of trust and co-operation between agencies and between agencies and mining companies. The spirit of co-operation has been reflected in greater public confidence that mining is environmentally responsible.  

Jan 1, 1995

By A. F. Neil, A. S. Bahaj, P. Watkins, P. M. Hyslop, C. E. Kirby, P. A. B. James

The results of initial work indicate that for 3 of the 5 quarry sands bioleaching reduces the iron oxide content to a commercially acceptable 0.035 wt% Fe20 3, although the time taken to achieve this is 14-22 days against a target leach time of 7 day. Subsequent work has identified strains of Aspergillus niger that are more efficient at producing the array of complexing agents for iron and is yielding excellent and rapid reductions in Fe levels. Potentially, bioleaching offers a more environmentally friendly and energy-efficient process for the removal of Fe from glass-making sands than conventional routes but the production of organic acids by fermentation must be achievable with low-cost substrates such as sugar-beet molasses and lactose permeates for bioleaching to offer a commercially viable alternative to treatment with hot mineral acids. Silica sands usually contain three groups of Fe minerals: iron oxyhydroxides, which comprise crystalline types such as goethite and limonite tending to occur as thin, discontinuous coatings and in cracks and crevices on the surface of the quartz; the assemblage of heavy trace minerals, which include ilmenite, rutile, leucoxene, chromite and haematite, commonly present at levels of 0.1 wt% or less as discrete grains or sometimes cemented to the quartz; and clay minerals cemented in pits on the surface of the quartz and in association with weathered, discrete feldspars. The response of the assemblage of iron minerals to short periods of exposure to hot inorganic acids is broadly related to which group they belong to, those that form coatings being accessible to acid and tending to react rapidly whereas the trace minerals are usually resistant and react very slowly, if at all, and the clays are probably digested. The note reports on a preliminary study of the use of microorganisms to develop an alternative clean technology that will give results comparable to those achievable with hot inorganic mineral acids but with more environmentally acceptable procedures. Various fungi and bacteria produce organic acids when grown in certain media. When these acids come into contact with Fe-stained sand grains the iron is removed as soluble complexes. Several strains of Aspergillus niger have been found to produce organic acids from sugar, predominantly citric, gluconic and oxalic acids, their relative yields depending on cultivation medium and conditions. Sand samples were prepared from five quarries in the UK: Levenseat, Lothian; Redhill, Surrey; King's Lynn, Norfolk; Chelford, Cheshire; and Oakamoor, Staffordshire; ranging in iron oxide content from 0.035 to 0.153 wt% Fe203

Jun 18, 1905

By Peter Voulgaris, Allan Haines, Diane Walker, Ian de Bruyn

The Oyu Tolgoi porphyry gold and copper project is located in the south Gobi region of Mongolia. The Ivanhoe Mines project has the potential to become a long-life copper and gold producer that could rank among the largest in the world. There are five deposits which cover a strike length in excess of 6.5 km, from south to north they are named South Oyu, Southwest Oyu, Central Oyu, Hugo South and Hugo North. The first three, collectively known as the Southern Oyu deposits, are planned to be mined by open pits, whilst extraction of the deeper Hugo deposits is planned using block caving techniques. The pits will have diameters of approximately 1000m and a maximum depth of 550m. The geological environment consists of a sequence of porphyritic augite basalt, dacitic tuffs and sedimentary rocks that have been intruded by several generations of porphyritic quartz monzodiorite and numerous post mineralization dykes. Several major faults cut through the southern deposits juxtaposing the relative position of the stratigraphy. The geotechnical investigation for the Oyu Tolgoi Open Pits was conducted in three distinct phases of increasing complexity: scoping study; advanced scoping study and feasibility study. Each phase consisted of data collection, interpretation and analysis designed to progressively develop 3D geotechnical domaining for the empirical, structural and numerical evaluations. The development of the geotechnical design parameters for these green fields open pits posed many technical challenges, brought about by the conditions associated with a lithologically and structurally complex environment. The design work focused on the optimization of the pit geometry to conform to equipment selection and blasting characteristics. Limiting bench stack heights were derived from the influence of major structures. The overall slope angles in each pit sector were developed around the requirement for haulage ramps and geotechnical berms. This paper describes each of these aspects and the methodology used to address the integration of the geotechnical characteristics with the mining environment.

Jan 1, 2006

This study was conducted to determine the effects of a machine-mounted scrubber and water sprays on face methane levels. Testing was conducted in the NIOSH ventilation test gallery which was designed to simulate a full-scale mine entry. In the test entry, a model mining machine, equipped with water sprays and a simulated dust scrubber, was located at the face of a 20-ft box cut. Blowing ventilation was provided using a curtain with a 40-ft setback distance. Methane released from a pipe manifold located inby the mining machine was monitored at six locations that were 1 ft outby the pipe manifold. Tests were first conducted to evaluate the effects of using sprays and scrubber separately on face methane levels. Additional tests were conducted to determine how a scrubber used with various water spray systems would affect face methane levels. The use of either sprays or scrubber reduced face methane levels significantly. The combined use of sprays with the scrubber further reduced face methane levels a small amount. Primarily the sprays affected methane levels by changing airflow distribution close to the face.

Jan 1, 2001

By J. D. Noll, S. E. Mischler

Measurement and sampling of diesel particulate matter in mine air presents a challenge due to the complexity of the diesel aerosol. The results of a series of tests carried out by the National Institute for Occupation Safety and Health, Pittsburgh Research Laboratory, in an underground mine were used to evaluate several measurement methods that are currently used to characterize particulate matter emitted by diesel-powered equipment. This paper presents an overview of these techniques and examples of the results along with a discussion of the advantages and information gained by each technique. The measurement methods discussed include particle size measurements using a scanning mobility particle sizer, total particulate matter measurements using a tapered elemental oscillating microbalance, a size selective sampling method for workplace and personal exposure assessment and a size-selective high volume sampling method for carbon analysis.

By K. Morita, N. Sano

Thermodynamic properties of chromium oxides in molten slags are very important for optimization of stainless steel refining processes as well as reduction processes of chromium ores. The solubility of chromite into molten slags has been found to vary considerably with oxygen partial pressure and slag composition in former studies by the authors. In the present study, activity data and redox equilibria of chromium oxides measured under moderately reducing conditions, PO2= 6.95x10–11atm, at 1873 K are summarized. For the CaO-SiO2-CrOXsystem, the activity coefficient of chromium oxide increased with increasing basicity, and the optimized slag composition for stainless steel refining is assessed as that saturated with CaCr2O4and Cr2O3usingthe phase relations determined. On the other hand, the presence of MgO and Al2O3brings about different behaviour of chromium oxide activity and redox equilibiria and the 44 mass per centCaO-39 mass per cent SiO2-11 mass per cent Al2O3-6 mass per cent MgO slag is recommended toreduce the chromium oxidation loss in the practical stainless steel refining process at 1873 K. Keywords: chromium, activity, stainless steel, AOD, VOD, oxidation loss, redox, CaO-SiO2-Al2O3-MgO slag

Jan 1, 2004

By William G. Doepken

With most of the mining industry emerging from the deepest business recession in 50 years, primary attention must be given to surviving in a business climate where dominant foreign competition, depressed prices, and potential overcapacity hang heavy over much of the industry. While already shackled with regulatory constraints, restrictive work rules, and high labor costs, mine operators are faced with the difficult task of reducing costs and improving productivity while operating at less than full capacity. To counter these nearly over-whelming factors, the mining industry must continue at the national level to seek regulatory relief and a rational policy toward foreign competition from government-controlled mines. In addition, dialogue with labor organizations must continue to minimize the impact of labor costs, cost escalators, and antiquated work practices. Although national and international actions have a tremendous impact on the future of domestic mining operations, local actions by mine operators to dramatically improve mining productivity will strengthen the industry's competitive stance. Before any substantial progress can be made, however, mine operators must recognize and define areas that depress productivity and establish goals and measures for improvement. Once problem areas are defined, a combination of technological and motivational concepts can be applied to improve productivity. Timing of Improvements While there is an immediate need for productivity improvements, only certain concepts offer near-term improvement potential while others must, of necessity, fit into a mid-range or long-range time frame. Near-term solutions (immediate to one year) likely will involve motivational concepts - work incentives and training - coupled with available technological concepts that require little capitalized development or site testing. Mid-range solutions (one to three years), by contrast, will include technological improvements in mining equipment, techniques, and systems automation. These concepts require a longer period of capitalized development and site testing before use. Long-range solutions (three years or more), which include adoption of new mining methods and computerized control systems, will appear only after prolonged research and capitalized development programs. Motivational Improvements Developing motivational con-

Jan 11, 1983

By L. B. Berger

Tests and observations of a Diesel-powered locomotive used for under-ground haulage, in a-clay mine were made by representatives-of the Bureau of Mines .primarily to determine the composition of the exhaust gases produced by the engine under actual haulage conditions-and to determine the effects of the operation on the quality of the mine atmosphere. In addition to ascertaining these conditional t proved interesting to analyze the test, data in regard to certain other performance, characteristics of the engine. This report presents results of tests of the mine locomotive, prefaced by a brief resume of the performance characteristics of Diesel engines to facilitate discussion.

Jan 1, 1948

By K. S. Seljesater

SINCE the development of dispersion-hardenable lead-antimony alloys1 in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. EXPERIMENTAL In order to-study the effect ,of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per FIG. 1..-CHANGE OF MICRO-BRINELL HARDNESS WITH TIME OF 1 PER CENT. LEAD-ANTIMONY ALLOY. cent. lead). The alloys were cast into bars 1 ½ in. wide by ¾ in. thick and cold-rolled to about 1/8 in. thickness. Three samples of each composition were annealed 1 hr. at 225° C. and quenched in water. One set was aged at room temperature, one at 50° C., and the third at 100° C., the

Jan 1, 1929

By Don McCarthy

Modern mining has been dominated by the drill-and-blast method for more than a century. There have been steady improvements in drilling technology, explosive products, methods of initiation and integration of the two techniques but the essential cyclical nature of drill-and-blast rock excavation naturally limits continuous improvements in cost and productivity. Dynamite and safety fuses, compressed-airdriven tools, and most of the crushing and grinding machinery in use today were all developed before 1900. Moreover, virtually every mechanized mining system used today was in use by the late 1950’s.

Jan 1, 1998

By A. M. Tonnos

Underground mining has yet to see an industry wide solution for control of their ventilation systems due to the complexity and sensitivity of the underground environment. Complexity arises from multi-level, multi-zone operations and sensitivity is associated with the impact that changes in equipment status and output have on air flows and quality throughout the mine. Our approach to solving this challenge incorporates system modeling and industrial control systems in a unified architecture. Although this approach can be applied to other processes and industries, this paper will cover the theoretical and practical aspects of an integrated model-control system (MCS) as it applies to underground mining ventilation.

Jan 1, 2009