Search Documents

By J. E. Terry

This paper outlines the steps that are being taken to close the gap between training and industry and indicates areas in which more work needs to be done. Although based on experience in the Maritime Provinces, it is applicable to industrial and educational studies across the length and breadth of Canada.

Jan 1, 1970

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

With a price slowly rising above US$35 per ounce gold became a mineral worthy of prospecting and mining endeavour in the early to mid 1970s. Fortune therefore appeared to smile onNew Zealand with its favourable geological environment for gold and past record of major gold production from both hard rock and placer deposits. This was a particularly welcome development as the post war years, including both the base metal exploration boom of 1967/1971 (which produced major nickel, iron and bauxite mines in Australia) and the earlier period of uranium exploration failed to produce any mines in New Zealand with the exception of the small Tui Mine and iron sand mining. Whilst hard rock mining now appears imminent it is 15 years further along the track since the 1967/1971 exploration boom and eight years since the upsurge in prospecting for gold in 1978. New Zealand still has no hard rock base or precious metal mining. This is not for want of proven or potential gold mining situations for these clearly exist at Waihi, Monowai Reef, Golden Cross, MacRaes Flat and elsewhere.

Jan 1, 1986

The Influence of Particle Shape in Rock Fracture

Sep 13, 2010

By Peter Fischer

Between 45,000 and 50,000 claims for subsidence are submitted each year to the German hard coal industry. In order to improve the service to claimants a quality management was established in 2005. This paper describes the process now used for handling these claims. A quality check has also been carried out by way of a customer survey, which was performed by an independent research agency. The results of the survey are presented in this paper. In Germany, research into mining subsidence mainly involves the prediction of ground movements caused by deep mining operations. Special areas of research are subsidence reducing aspects of the extraction panel planning, especially from the point of view of mining dynamics, as well as securing and restoration measures. This work seeks to prevent or minimize mining-induced damages close to the surface, for instance, buildings or infrastructure installations (such as pipelines), or underground mine openings (e.g. shafts). Roof collapses and surface fractures caused by shallow mine workings of an earlier era currently constitute a special area of investigation.

Jan 1, 2006

By M. Q. W. Jones

This paper summarizes important features of a compilation of thermal properties of stratified rocks from Witwatersrand gold mining areas. The database consists of more than 1000 thermal conductivity measurements, more than 700 density measurements, and nearly 100 heat capacity measurements. Most important rock types and stratigraphic units are well represented. Heat capacity does not differ significantly from one rock type to another, and density is relatively uniform although particular rock types are characterized by distinct average values. Different rock types also have distinct thermal conductivities, but this parameter varies by a factor of four to five. Primary factors controlling the thermal properties are mineral composition, degree of metamorphism, and porosity. In addition, the temperature dependence of thermal conductivity and heat capacity of quartzite may significantly decrease the thermal diffusivity of this rock at deep mining levels.

Jan 1, 2003

By H. Ogasawara

Information on rock stress is important for safe mining in seismically active ground. On a major gold mine, a few tens of crews are continuously conducting geological drilling with small pneumatic machines. However, stress measurements are not often carried out in South African deep-level gold mines. One of the reasons is the drilling diameter that overcoring requires, which is much larger than the diameters used in regular geological drilling, e.g. Boart Longyear Metre Eater, which drills A[O] or B[O] holes. Larger diameter holes result in slower drilling advance, more load in transportation and handling at sites, and higher cost. In order to enable overcoring in BX size (60 mm diameter), we modified the compact conical-ended borehole overcoring (CCBO) technique that has been suggested by International Society for Rock Mechanics (ISRM) and was originally designed for NX drilling (76 mm diameter). With a single overcoring, the 3-D stress tensor can be determined. We tested this modified method at a depth of about 3 km at Moab Khotsong mine in South Africa. We worked with drilling crew who usually work at geological drilling with the Metre Eater. In January 2011, we tried using regular geological drilling tools (a sequence of a normal BX bit, reamer, and rod) without success. In August and September 2011, introducing stabilizers and thin BX bits, we succeeded. We could complete a cycle of procedures necessary for an overcoring, including shaping the borehole-end conically, glueing a 16-element strain cell, and overcoring, within 2.5 hours. Only 10 cm overcoring is needed, which increases the chance of successful overcoring in heavily fractured conditions. This modified method is suitable for up-dip holes to depths of 10-15 m from tunnels, and has the potential to be widely used at the initial stage of geological exploration drilling at many localities.

Jan 1, 2012

This study was conducted to establish the effects of a diesel particulate filter (DPF) system with sintered metal substrate on the concentrations and size distributions of nano and ultrafine aerosols and concentrations of nitric oxides in underground mine air. The study focused on the formation and transformation of nucleation mode particles in mine air under prevailing test conditions. Experimental work was conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of control technologies directly in underground conditions. The DPF system was examined for four repeatable steady-state engine modes using a naturally aspirated mechanically controlled Isuzu C240 diesel engine fueled with ultralow sulfur fuel. The engine coupled to an eddy-current dynamometer was operated in the underground drift with tightly controlled ventilation. Measurements upwind and downwind of the exhaust system discharge were used to quantify the effects of the DPF system on the mine air. A baseline was established using a standard muffler. The study showed that sintered metal DPF systems reduced the total mass of aerosols in the mine air by more than ten-fold when compared to a muffler. The nucleation mode aerosols (50dem<40 nm) in mine air were found to be strongly influenced by engine operating mode. The concentration of nucleation mode aerosols was found to be significantly higher for high-load modes than for low-load modes. The muffler and DPF system resulted in comparable total nitrogen oxides (NOx) concentrations. However, the nitrogen dioxide (NO2) fraction of the total NOx was found to be substantially higher for both systems for low-load modes than for high-load modes.

Jan 1, 2009

By P. D. Lohn

The objective of this program was to develop nozzle designs to maximize the effective cutting length of a water jet. The results of the theoretical program directly support the Bureau of Mines Borehole Mining Program and their experimental program to improve the rock cutting capability of water jets. The borehole geometry requires turning the flow by 90 degrees and accelerating through the nozzle within a restricted length. Several suggestions for turning the flow are offered. The borehole space limitations constrain nozzle length, to the extent that a standard 13-degree tapered nozzle (6-1/2 degrees half angle) is too long to fit in the borehole, at production flow conditions. The design technique developed is computationally economical and enables examination of a large number of shapes and flow conditions. The nozzle design is based on design criteria of minimization of boundary layer thickness at the nozzle exit and minimization of the possibility of separation and cavitation. Six flow conditions, including pressures to 4500 psi and flow rates to 400 gpm, were examined, Best shapes were determined for all flow conditions. The best shape for a borehole reining application consists of an initial 4th degree polynominal (quartic) at the entrance followed by a straight section with a twenty degree (half-angle) taper at the exit.

Jan 1, 1976

By K. T. Audt

The Yayoi period, from about 300 B.C. to A.O. 300, represents a time of important changes in Japanese history. During this period the advanced rice culture of the Asian continent was introduced to Japan, along with the techniques of animal husbandry, spinning, bronze casting and metal working(1) . As was the case in the Jomon period (11000 B.C. to 300 B.C.), the Yayoi period is traditionally defined by a particular type of pottery, characterized by the use of the potter&apos;s wheel and an extreme simplicity of decoration and form(2) . Pieces of this pottery were found in 1884 in a district of Tokyo, known as Yayoi-Cho, not far from Tokyo University. Within a decade the name Yayoi had come to be used for the period which also saw the first casting of metals in Japan121. During the Yayoi period, the foundation of the ancient Japanese state was laid as the individual small communities were unified and as labour specialization and social levels developed. In fact, the Yayoi may be the true ancestral culture of Japan(3) . However, the origin of the Yayoi is not definitely known. One theory indicates that the Yayoi people may have been driven from the Asian mainland (via Korea) by the dynastic wars that accompanied the unification of China under the Ch&apos;in and Han and that these settlers rapidly displaced the Jomon. Bronze objects and the cultivation of rice may have arrived about the same time - in the third century B.C. Iron was in Japan within another century, but since it rusts badly and disintegrates, only a few small pieces are known from such an early date(4) . After about 50 B.C., the Yayoi cultures of western Japan were in fairly close and regular contact with the continent via Korea(5)

Jan 1, 1999

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By M. Maldonado, J. A. Finch

"A flotation bank consists of a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three strategies for optimizing bank performance: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data is analyzed in respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.INTRODUCTION Flotation is used to separate valuable minerals from each other and from gangue. To reach a target metallurgical performance, usually assessed in terms of concentrate grade and recovery, feed is passed through stages such as roughing, cleaning and scavenging. All these stages comprise serial arrangements of flotation cells known as banks, lines or rows. Although a bank is the simplest interconnection of cells in a circuit, i.e. the tails of one cell is the feed to the next cell down the bank, how to operate each flotation cell in a way that the whole bank performance is optimized remains a challenge. Significant efforts have been made towards understanding the effect of operating variables on the flotation performance of an isolated cell (Lynch et al., 1981; Finch and Dobby, 1990; Gorain et al., 1998). However in the case of banks the variables that can be manipulated increase with the number of cells in the bank and the problem of how to manipulate them to achieve optimum performance is difficult even disregarding variation in ore characteristics (Lynch et al., 1981, p. 16). In general, the more manipulated variables available the better for optimization purposes, however without clear guidance how to effectively use them it becomes an “embarrassment of riches”."

Jan 1, 2012

By Albert Adu-Acheampong

Fairmount Mineral&apos;s Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 381-mm- (15-in.-) diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially available, high-volume/ low-pressure fans combined with a systematic layout of control structures. The recommended redesign was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2008

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau&apos;s turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

By Bing W. Jong

A bench-scale evaluation of coal and coal waste materials as aggregate materials for use in longwall mine supports was undertaken as part of the Bureau of Mines Health and Safety program on ground control. Performance data were obtained on portland cement concretes (PCC) prepared with coal and coal wastes as aggregate materials. The effects of high-early-strength accelerators on strength and creep and of superplasticizers on strength properties of PCC formulated with coal and coal waste were investigated. Concrete formulated with a high-early-strength accelerator and coal and coal waste has 20 and 40 pet greater compressive strength, respectively, than the control samples without admixture. A concrete formulated with coal waste and the high-early-strength accelerator, using four bags of cement per cubic yard and a water-cement ratio of 1.0, had the lowest creep value of all the coal- and coal-waste-formulated PCC&apos;s tested.

Jan 1, 1983

By R. W. Brigstocke

History The birth of the mining industry of Canada took place about 1670. According to Salone (Salone E., La Colonisation de la Nouvelle France, page 205) the first discovery of ore in the country was made by an iron-master, Monsieur de la Potardiere, near Trois Rivieres, Quebec. Under French rule some prospecting was done; but at this time no one seemed to consider the working of mines practicable. It was not until the time that Begon became Intendant, when the Marquis of Vaudreuil was Governor, that mining was attempted. Begon was a patron of industrial arts and did his best to promote home manufactures. The mining industry was developed under his regime and discoveries of copper and lead ores were made in 1730. About this time the St. Maurice Forges were erected to treat bog-iron ore, and they were in operation for many years. Prior to 1747, iron pans to the value of £21,000 were manufactured, together with bar-iron and plough-shares. About 1769, that is, ten years after the conquest by Wolfe, stoves and other articles, and, later, potash kettles, appeared. What is still more interesting to us-or was, at least, to General Wolfe-is that cannon balls made at the St. Maurice Forges delayed his operations. A map dated 1744, a copy of which appears in the report of the Ontario Bureau of Mines for 1913 (Vol. XIX), indicates the extensiveness of the wanderings of the French and also shows the location of the lead mine on the east shore of Lake Timiskaming. Bog-iron ore was turned into metal, with charcoal for fuel, at Norman-dale, Norfolk county, Ontario, in 1813, and at Clementsport, Nova Scotia, in 1825. In a volume published in 1672, reference is made to the occurrence of coal on the Atlantic seaboard, and in 1677 Monsieur Duchesneau, the Intendant, levied a royalty of twenty sous per ton on all coal taken from Cape Breton.

Jan 1, 1932

By T. Markus, K. Hilpert

Discharge vessels of advanced light sources are made of translucent polycrystalline Al2O3(PCA).These tubes contain salt mixtures, which essentially consist of metal halides. The salt mixture is present as a melt at the coldest spot of the vessel under operating conditions and vaporizes partly. The temperatures of the coldest spot range between 1200 K and 1300 K, depending on the lamp performance. The maximum wall temperatures range up to 1500 K and for special purposes up to1700 K. Important constituents of the melt are alkali halides AX (A = Na, Cs, X= Br, I) and rare earth metal halides LnX3(Ln = Dy, Ho, Tm). Severe corrosion attack on the wall material is observed in the PCA discharge vessels. The aim of this work is to elucidate the corrosion mechanism. Annealing experiments under well defined temperatures were carried out in order to understand the complex chemical corrosion processes. Two different annealing vessels were used, one for experiments under isothermal conditions with a temperature of 1473 K and one for experiments with a linear temperature gradient from 1450 K to 1600 K. The vessels were filled with salt mixtures of different compositions and annealed for 1000 h. The corrosion attack was characterised by XRD, analytical electron microscopy, high temperature mass spectrometry, and chemical analysis of the salt melts. The results of our investigations show that the corrosion attack is caused by vapour species and by the salt melt. The most severe corrosion is observed in vessels filled with mixtures of alkali halides and rare earth metal halides. No corrosion of the alumina is practically observed if pure alkali halides or pure rare earth metal halides are present in the annealing vessel. Keywords: thermodynamic, corrosion, lamps, metal halide salt

Jan 1, 2004

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs fur improving mine safety. One area of interest to the Bureau is new and improved means for minimizing the hazards of accidental gas ignition or electrical shock should the frame of an off-track machine assume potential above ground. Various means presently used to prevent such occurences are the use of ground fault detectors for phase to ground faults in ac machines, and grounding conductors and diodes in dc machines. In a three phase ac power center, a phase to ground fault may be detected by monitoring the current in the grounding resistor which is required between the power center neutral on the load side of the power center transformer and ground. Another method for detecting a ground fault is to pass the three load conductors through a toroidal core transformer. The phase currents vectorially add up to zero if none of the phases are faulted, and hence the voltage of the transformer secondary is either zero or not zero if one of the phases is unbalanced or faulted.

Jan 1, 1976