Search Documents

Important factors in dredge design are the estimation of total head, and the determination of flow in and around suction nozzles and in pipe lines. Total head for the dredge pump is calculated from velocity, static, and friction heads. Flow into suction nozzles depends on whether hydraulic jets or mechanical cutters are used, and on nozzle shape. Design of pipe lines depends on the transportation characteristics of the pulp, skin friction, swirl, and the avoidance of cavitation. Measurement and control of flow is important.INTRODUCTIONEconomic deposits of heavy minerals along the east coast of Australia occur in frontal dunes, which are normally unconsolidated and granular, or in hind dune areas which may contain indurated seams interspersed with loose material. In working frontal dunes, dredging depths are usually shallow since values do not persist for more than a few feet below sea level. However, the controlling factor in dredging the hind dune areas is the level of the water table and suction dredges may be designed to mine to depths of 120 ft, or even more, if necessary.In previous applications of suction dredges in the industry attention was directed primarily towards production and there was only limited research on fundamental techniques. However, with lower grade deposits now forming the major ore reserves, production levels and profit margins will fall unless more efficient dredges are developed.For satisfactory design of dredges it is essential that the total head be accurately estimated and that detailed information of the principles of flow in and around suction nozzles be determined. This paper presents information gained from field experience and laboratory investigation on these aspects.

Jan 1, 1962

By Gregory R. Gorrell

The legal issues surrounding the regulation of subsidence are among the major concerns facing the underground mining industry today. Whether subsidence occurs almost immediately as a result of longwall mining or without warning as a result of room and pillar mining conducted years ago, the resulting disputes are highly controversial and typical of the disputes involving the competing interests of surface and mineral estate owners. Until recently, the law governing these disputes was firmly established under the common law. The passage of the Surface Mining Control and Reclamation Act 1, the utilization of new mining technologies, and the general heightened environmental awareness of our times, however, have interjected new issues into this area of the law. State and Federal court decisions and administrative agency interpretations have helped clarify some of the issues. However, as evidenced by the many recent lawsuits between operators, surface owners, and regulatory agencies, many uncertainties still exist.

Jan 1, 1986

To optimise the haulage of the large tonnages produced from stopes in this high production gold mine, an ore pass and feeder system was introduced. This ore pass was designed and developed in 2006 and the plate feeder installed and commissioned soon after. Cavity Monitoring Surveys (CMS) have been undertaken of the ore pass since it was commissioned. The original thickness that was surveyed of the pillar between the ore pass and decline in 2006 was approximated to be 19 m. Throughout its use large blocks of rock were reporting at the plate feeder. This was the first indication that the ore pass was failing somewhere between the tipping level of the 9410 level and the plate feeder at the 9330. Even so CMS surveys were not taken systematically to firstly identify the area of failure or for monitoring. In August 2008 after implementing management systems, large blocks were still reporting to the plate feeder. The decision was made to empty the pass enough to carry out a CMS survey of the area. Subsequently it was discovered that the area of failure was between the decline and ore pass and that since the first survey the pillar thickness had been reduced to approximately 9.7 m. Further management controls were put in place to slow movement of the material and to limit the use of the 9410 tipping level, but this did not alleviate the rate of failure entirely. The results of an initial inelastic numerical model indicated that most of the pillar was damaged and that failure into the decline likely if no changes were made. The numerical modelling predicted that even if material was no longer passing through the ore pass interaction between the voids was unavoidable and would most likely result in instability. The ore pass and plate feeder are an integral part of the haulage system for the remaining life-of-mnie. Two solutions were sought to firstly reinforce and stabilise the pillar between the ore pass and decline and secondly to rehabilitate the ore pass or find an alternate design that could still utilise the plate feeder. This paper summarises the analysis and resulting rehabilitation that was used to accomplish this.

Nov 25, 2010

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau's annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By Steven Hoerger

Newmont Mining has a large, integrated gold-mining operation in northern Nevada with several mines, stockpiles and processing facilities. There are more than 90 defined metallurgical ore types and more than 60 defined gold-recovery process options. Newmont developed a mine plan and process model to take better advantage of the available synergies at its Nevada mines. This plan includes a mixed integer and linear programming optimization tool. This system is maintained and operated by a Nevada planning group. Standard in-house planning software tools and methods have been implemented at all mine sites. These changes have allowed a reduction in mine engineering staff and have increased the effectiveness of mine planning.

Jan 1, 1999

By D Lautier, A A. Ndiaye, A Galli

Traditionally gold producers had built up hedge books to protect themselves against adverse changes in the commodity price, but diversified mining groups were staunchly opposed to hedging in any shape or form. The situation has evolved over the past few years. Gold miners have been reducing the size of their hedge books in line with the rising gold price. Commentators have talked about ædouble-digit dehedgingÆ and have suggested that this is the final countdown for gold hedge books. It sounded as if the era of hedging by mining companies was drawing to a close. But as appearances can sometimes be misleading, we decided to find out what mining companies were actually doing. Companies listed on stock exchanges are now obliged to give details of their derivatives holdings in their annual reports. Two or three years ago there was no such obligation. Our reality check was based on the latest annual report issued by three multinational mining groups; two with diametrically opposed views on hedging (Rio Tinto and Barrick) and the third (BHP Billiton) with an intermediate position. This snapshot of their derivative positions at a point in time revealed that Barrick and BHP Billiton have substantial derivatives positions (worth billions of dollars) to protect against adverse changes in foreign exchange rates and interest rates. Moreover Barrick has recently started hedging against increases in fuel prices. Despite its opposition to hedging, Rio Tinto has derivative positions worth several hundred million dollars, but these are primarily a legacy from various mergers and acquisitions over recent years or were entered into as a condition of project financing. Lastly we were surprised to discover that Barrick was holding asset-backed commercial paper (ABCP). So the idea that mining companies donÆt hedge their risks is just another urban myth.

Jan 1, 2009

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Mohamed Ourriban, Yongjun Peng, Qi Liu, Denis Cotnoir

"In the flotation of fine particles, there are two difficulties in general: low recovery of valuable minerals and high recovery of gangue minerals. The low recovery of fine valuable minerals is attributed to low bubble-particle collision and attachment efficiencies, while high recovery of fine gangue minerals is attributed to mechanical entrainment through water films between gas bubbles. Over the last five years COREM has been actively developing fine particle flotation techniques with the objective of improving fine particle flotation separation efficiencies.The fine particle flotation techniques with both generation of micro bubbles and enlargement of sizes of fine particles have been developed to increase bubble-particle collision efficiency. For oxidized fine sulphide minerals, both physical and chemical techniques have been developed to modify the hydrophilic surfaces and therefore increase bubble-particle attachment efficiency. To reduce mechanical entrainment of fine gangue minerals, a new approach, polymeric depression and flocculation, has been developed. By selecting the high molecular weight polymeric depressants to make fine gangue minerals hydrophilic and also enlarge their sizes, entrainment can be minimized. By combining these techniques, we are able to improve both flotation recovery and selectivity in some fine ore flotation systems.INTRODUCTIONWith depleting mineral resources and their declining grades, ores leaving grinding circuit for froth flotation are becoming increasingly finer to achieve mineral liberation. Together with the increasing demand for minerals, ever-increasing tonnages of fines are being produced. Therefore, flotation of fine particles is an immense challenge to be tackled by researchers all over the world today."

Jan 1, 2006

By G. Tranell, L. Kolbeinsen, S. Gaal, J. Safarian

The effect of carbon material properties on the rate of MnO reduction from ferromanganese slag by solid graphite was investigated. A sessile drop technique was used to study the reduction rate of a synthetic slag containing 45 wt% MnO at 1500 and 1600 ºC. Different types of graphite substrates were used and the con-tact angle between slag droplets and substrate were measured in-situ. Moreover, the slag droplet volume during the interaction with the graphite substrates was calculated and normalised. The mathematical relationship between the slag density during the reduction and the normalised slag droplet volumes during the reduction were derived and the MnO reduction curves were then calculated. A method for measuring the slag reactivity of solid carbon was defined and used to qualify the propensity of the different graphites to react with the liquid slag. Some supplementary studies such as manganese evaporation measurement and EPMA analysis for determining the extent of MnO reduction were also carried out. It was observed that there is nota significant difference in the wetting angle of the graphite substrates by the slag, and the wetting is not changed within the temperature range of 1500-1600ºC. However, the changes in the contact angle during the slag reduction at 1600ºC are more than at 1500ºC. The kinetics of MnO reduction is dependent on the type of graphite and it is more dependent on the graphite properties at lower temperatures. On the other hand, the dominant properties of graphite on the reduction rate vary with temperature. A multivariate analysis on the graphite properties and the parameters related to the slag reactivity indicated that the kinetics of MnO reduction is mainly dependent on the temperature, and then on the graphite properties. It was also found that at1500 ºC the surface area and the CO2 reactivity are the most important graphite properties for the slag reduction, suggesting that the reactivity of carbon is rate controlling at 1500 ºC. However, the porosity related parameters are the most important graphite properties at 1600 ºC, suggesting that CO gas desorption is rate controlling at high temperatures.

Jan 1, 2007

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978

By Stephan Großwig, Karolina Nycz, Arne Kindler

"Commonly used anchor monitoring systems are mainly based on the use of anchor force meters. However, experience shows that the reliability of the display of force meters lowers over time. Other measurement and test methods like for example fibre bragg grating method require a comparison with an unloaded optical fibre and give only selective information about the bearing behavior. Moreover the obtained information has to be interpreted. In the following article, first measuring results of an anchor monitoring system based on measurements with optical fibre are presented. The new monitoring system is based on the Rayleigh technology and was used to test the load bearing behavior of the anchor grout body as well as for the evaluation of the grout body condition in concrete-damaging groundwater.INTRODUCTIONThe first fibre optic sensors came onto the market about three decades ago. Initially used as special solutions only in selected cases, now they have found use in almost all areas of technology, especially in areas, where electrical sensor systems reach their limits. The first application examples of spatially resolved fibre-optic sensors in the field of geotechnics have been in existence since the mid-1990s, in projects such as the assessment of the of radioactive repository location sites (Hurtig et al. 1994), for the monitoring of landfill sealing systems (Hurtig et al. 1995) or within the framework of the rehabilitation of mountain farming landscapes (Schreck et al. 1998).The company's first own works in the field of glass fibre measurement technology have been in existence since 1993. The first carried out projects were a monitoring at the Edertalsperre (Dietz et al. 2001), a monitoring with glass fibre tendon at a flood bridge in Carinthia as well as monitoring within the framework of the Storebælt crossing. In all cases, the structure was permanently monitored by means of individual-point measurements. Since 1993 various fibre-optic sensor solutions for geotechnical applications have been introduced to the market (Voet, Glötzl 1996, Hurtig et al. 1994)."

Jan 1, 2017

By W. Mbhalati

"Conzal Mine was not meeting production targets in 2013, and it was established that this was caused by the inability of the load haul dump machines (LHDs) to tram the required tonnages. An investigation of the LHD productivity was therefore conducted to identify the inhibiting factors. This was accomplished by carrying out a literature review on LHD operations to gain in-depth knowledge and conducting observations in the working environment. The relevant information and data on the LHD type used at Conzal was also acquired.The major inhibitor was found to be excessively long tramming distances in all the sections of the mine. The one-way tramming distances were all significantly greater than the 90 m set in the mine’s code of practice (COP), with the Main Shafts section having the longest average one-way tramming distance of 260 m. The other inhibitor was LHD utilization, which in 2013 was only 47% against a target of 70%. Simulation of the LHD operation, taking these two factors into account, showed that production could be increased by more than 100%. As a result, it was recommended that conveyor belts should be extended regularly in order to keep tramming distances within the recommended one-way distance of 90 m. In addition, utilization can be improved by minimizing employee absenteeism as well as by modifying the travelling routes such that LHDs do not encounter unnecessary delays.Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection and operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

Rutile Beach Sand from Hard Rock

Sep 13, 2010

By G. Bierie

The conveying of bulk materials is prone to problems. These problems can reduce the capacity and efficiency of the plant, and even threaten the health and safety of the workforce. This presentation will look at new conveyor technologies systems, and how, used separately or in combination, they can improve material handling.

Jan 1, 2007

By George K. Burke

Underpinning of a structure has been traditionally expensive, time consuming, and, in many cases, caused as much settlement to the existing structure as it was trying to prevent. As underpinning is normally one of the initial tasks and on the critical path on a construction project, there is immense pressure on the subcontractor to speed up his operation so the new structure can proceed; this can cause an adversarial relationship to develop between the owner, engineers, general contractor and subcontractor. Since its introduction to the North American market in the late 1980's, Jet Grouting has not solved all these problems, but where utilized, has shown economical benefits, a faster and safer installation, and a minimal movement of the structures being underpinned. A history of the development of jet grouting is presented; a comparison of this technique versus other grouting methods, a description of the jet grouting system with emphasis on the triple rod systems; case histories of jet grouting used for underpinning and conclusions and references are included to follow the program's themes of: - Recognizing Solutions to Today's Problems - Defining Tomorrows Challenges - Putting America on a Solid Foundation

Jan 1, 1991

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection Paid operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949

By Steve Kral

Worker safety is an issue that transcends industries, whether it be mining, construction, manufacturing or even general office work. In the mining industry, safety and training are particularly important because mining is a dangerous occupation. Throughout the years, federal and state safety regulations have been written and revised to keep up with the changing technologies. And mine operators have installed their own safety and training programs. They have come to realize that a safe and healthy workforce has positive effects on productivity and profitability —not to mention avoiding the high costs of injury-related absenteeism.

Jan 1, 2003