Search Documents

By Snowden C. T

B Lens Main is a scheelite orebody with an average dip of approximately 15¦ and thickness ranging from 1.5 to 6.0 m. The orebody is overlain by a banded section of ore and waste which tends to slab off if left unsupported. It was originally planned to mine a large portion of this orebody by room and pillar methods, with existing diesel trackless equipment. This, however, proved unsuitable for a number of reasons and the smaller scale method of slot stoping with hand machines and scrapers was employed. The following major problems were encountered. 1. The method was new to the mine and the work force, and had to be commenced quickly using existing or easily obtainable equipment. This is gradually being overcome by training, modification of procedures and introduction of more suitable equipment. 2. The slabbing from the hanging wall had to be controlled, either by support or by mining this low grade section and accepting the resultant dilution. This has been approached in a number of ways, depending on conditions and the method will have to be further modified as different conditions are encountered in new areas.

Jan 1, 1977

In recent years new instrumentation and digital technology have Wrote possible a new facet of goo-physics: broadband seismology. From digitally record-ing networks and arrays. broadband scistnograrns of body waves that are flat to displacement and veloc-ity in at least the frequency range from 0.01 to 5.0 liz can now be routinely obtained for most carthquakes of magnitude greater than about 5.5. In contrast to data from conventional narrowband seismographs, broad-band body waves have sufficient spectral information to nvest,igate the many frequency-dependent eflects that may arise from source finiteness and from wave prop-agat ion phenomenon. Besides the usual parameters of depth. moment and focal mechanism, broadband data have sufficient spectral information to provide estimates of radiated energy, associated stresses and the frequency dependence of source parameters. Moreover. teleseis-mically recorded broadband data and near-field strong motion accelerograms overlap in the frequency band be-tween about 0.1-2.0 Hz. Thus. v it h broadband data it is possible to connect far field and near field data in order to make estimates of acceleration for almost any seismically active region of the circum-Pacific.

Jan 1, 1990

By B C. McLellan

The decline of ore grades on land, increasing demand and high prices for various minerals have led to an increased interest in mining the deep ocean sea floor. The potential deep ocean reserves are vast and in some circumstances the grades are high enough to consider mining. However, the consequences of such mining are as yet uncertain. This paper will present the results of a comparative assessment of life cycle impacts of deep ocean minerals. Two alternative extraction technologies from different deep ocean resource types were examined and key commodities are considered. Initial results indicate that the energy requirements will be higher than the average land-based resources, but may fall within the range of the deepest terrestrial mines.CITATION:McLellan, B C, 2015. Comparative life cycle impacts of deep ocean minerals and land-based counterparts, in Proceedings Third International Future Mining Conference, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Cameron Soltys, Hamid Ghorbani, Maher Al-Dojayli

Cooling staves in blast furnaces are used to minimize the process heat loads on steel shell and refractory system. Copper staves are exposed to significant fluctuating thermal loads which may lead to premature stave failures due to cracks, water leakage, bending, abrasion and resultant wear. In this paper, an assessment methodology is presented to evaluate the effect of thermal cycling on copper staves including bending, fatigue and thermal ratcheting. This approach incorporates temperature-dependent copper properties including creep and plasticity to more accurately capture inelastic deformations, damage and fatigue in staves under transient and cyclic thermal loading conditions. Root cause failure assessment and improvements to copper stave design can be assessed using the presented methodology.

Oct 1, 2019

By Renato G. Bautista

"The chemistry of the separation of metals from each other and from the other undesirable components involve multiple simultaneous chemical reactions. In the case of leaching, the heterogeneous chemical reactions between the solid and the liquid phase may be limited to a few reactions. In the homogeneous liquid phase, the number of simultaneous chemical reactions could be double or triple that of the number of heterogeneous reactions. The rate of dissolution becomes very dependent on the changing concentrations of the significant chemical species taking part in the multiple reactions in both the heterogenous and homogeneous phase. The rate expression developed for the process must take into account the mechanism of chemical reactions in order to best represent the actual process. This paper also examine the role of mass transfer with chemical reaction in the develpoment of the rate equations for dissolution, liquid-liquid extraction, membrane separation, precipitation, and electrodeposition.IntroductionThe understanding and the elucidation of the mechanism of the rate phenomena for a specific chemical reaction system is of prime importance in the development of a successful chemical process. The development of successful emerging technologies for metals separation will depend on the accurate interpretation of the intrinsic chemical reaction kinetics and the rate of mass transfer of the desired metal species during its separation from the undesirable chemical species. This is the case whether the process application is for separation, concentration, and /or purification.The chemical processes that will be examined in this presentation will include leaching, solvent extraction, membrane separation, precipitation, and electrodeposition."

Jan 1, 1996

By K. Trybalski

Facing the optimization activities, which purpose is to minimize the copper processing costs, the main sources of their occurring were presented. In this purpose, the costs analysis was performed, divided to individual standings, for one of the polish copper beneficiation plants. It was proved, that the main component of the copper beneficiation costs is energy consumption, generated mainly in grinding and classification node, particularly by operating mills. The technological system ? grinding and classification node ? in KGHM Polska Miedz S.A., ZWR region Lubin was then selected to investigation. To evaluate the grinding and classification node, the energetic factors W were proposed, calculated on the basis of the energetic-technological data of process, given by node monitoring system. The correctness of the energetic factors selection to evaluate the work of this node and their practical application in industrial conditions was experimentally proved in other technological object. The selected technological object ? grinding and classification node ? was then mathematically modeled and optimized. The calculated energetic factors were the basis to build mathematical models, identifying industrial copper grinding and classification process. The models described correlation and character of dependency between factors and energetic-technical data of the process. These were regressive and neural networks models. On the basis of factors models, the optimization tasks were determined, which purpose was to select the optimal points of grinding and classification node work. Also, the estimated economical effect, possible to achieve after introduction of given monitoring values to grinding and classification node optimization system, was presented.

Jan 1, 2014

By BARONJUPTNER VON JONSTORFF, Andrew A. Blair, GUNNAR DILLNER

IT is a well-known fact that the results of different analysts, when operating on the same identical sample of steel or iron, are far from concordant, and it not infrequently happens that great annoyance and trouble in the commercial community are occasioned by these discrepancies. Attempts have been made at various times to investigate the causes of such differences and to obtain more reliable methods of analysis. The most important of these was made by the British Association in 1889: The following gentlemen, with Sir W. Roberts-Austen as Chairman, and Professor T. Turner as Secretary, were constituted as a committee to investigate the question, viz.: Sir F. A. Abel, Mr. Edward Riley, Mr. G. J. Snelus, Mr. John Spiller, Professor J. W. Langley, and Professor Tilden. Average .samples of steel were prepared in America under the superintendence of Professor J. W. Langley. The steels, in the form of turnings, were divided and distributed to sub-committees in Great Britain, America, France, Germany, and Sweden. In Sweden Professor Åkerman acted as Secretary to the Swedish committee. The Government Department of Tests was appointed in Germany; Mr. Ferd. Gautier in France; the British Association Committee in England; Messrs. William

Mar 1, 1905

By T. K. McCranie, A. H. Tousley, A. H. Kackman, L. R. Gregory, A. Jr. McElrath, R. J. Krekel

In Roman and earlier civilizations the term cement was applied only to mixtures of lime, pozzolana, sand, water, etc., used as a mortar to bind larger stones. Today, portland cement, the subject of this section, can be briefly defined as follows: The product obtained by finely grinding clinker produced by calcining to incipient fusion (i.e., sintering) an intimate and properly proportioned mixture of argillaceous and calcareous materials. History The Egyptians were probably the first to join building stones with a mixture of sand and a cementitious material (i.e., having the property of or acting like cement). It is generally accepted that the cement used by the Egyptians on such structures as the Great Pyramid was calcined gypsum, Later the Greeks began to calcine limestone for use as a mortar with sand and water. Still later, broken brick and tile were added to the mortar to make the first concrete. The Greeks and Romans found that some sands produced mortars that were especially resistant to the action of water. Hydraulic (i.e., underwater-hardening) cements formed by combining slaked lime, water, and finely divided siliceous materials (e.g., pozzolana) possess superior strength and are capable of resisting the destructive action of water. They were used on the Pantheon, Colosseum, and other structures, some of which are still standing. In 1756 an English engineer, John Smeaton, found that an argillaceous limestone (i.e., containing an appreciable amount of clay as an impurity) produced a cement with greater resistance to the action of water. Despite Smeaton's findings, the use of the old mixture of lime and pozzolana long retained its popularity. Significant contributions in cement technology from England, Swe¬den, France, and Holland were made in the next 68 years. However, the invention of portland cement is generally credited to Joseph Aspdin, an Englishman, who in 1824 patented "portland cement." The name was selected because, on hardening, it resembled the natural building stone from the Isle of Portland, England. The patent features mixing ground limestone and argillaceous materials in appropriate proportions and calcining (i.e., expelling CO2 by roasting) the mixture. This superseded the existing practice of calcining naturally occurring argillaceous limestone. In about 1845 Isaac Johnson, also English, conducted experiments on proportioning the components and calcining them at higher tem¬peratures. His accomplishments are accepted as the beginning of the present-day portland cement industry. The U.S. cement industry originated with the demand for good hydraulic cement for building structures such as the Erie Canal, which was started in 1817. The first discovery of cement rock (i.e., naturally occurring argillaceous limestone with near-optimum ratios of calcium carbonate, alumina, and silica) near Fayetteville, N.Y., was made by C. White. In 1818, White secured a patent for the manufacture of natural cement from that deposit. Subsequently, several natural cement plants were built in 1830-1840 at Rosendale, N.Y., and in the Lehigh Valley of Pennsylvania. David Saylor, who participated in establishing a natural cement plant at Coplay, Pa., in 1850 discovered that a superior cement could be produced by calcining the rock at higher temperatures than hith¬erto. In 1871, Saylor obtained a patent and commenced the manufac¬ture of portland cement. By 1890, there were 17 portland cement plants in the United States with a combined annual output of 62,300 tons. At the end of 1970, the number of plants producing portland cement in the United States (including Puerto Rico) was 169, down from a maximum of 185 in 1967, with total annual shipments of 73.4 million tons valued at $1,298 million. (Fig. 1). In 1970, annual world production of hydraulic cement (which includes pozzolanic materials, hydraulic limes, natural cement, alumina cement, and portland cement, all of which are in current use in various parts of the world) reached 630 million tons (Table 1). Flowsheets of typical U.S. cement plants are shown in Chapter 13. Chemical Composition and Physical Properties It is generally accepted that portland cement clinker consists of a mixture of compounds or synthetic minerals. The four principal compounds are:

Jan 1, 1985

By Seth K. Martin, Tony Nichlany, Alan R. Poeppel, Konstantinos Syngros

"This paper presents a case study on bored pile construction in challenging karst conditions below a supertall building in Kuala Lumpur. Innovative design and construction techniques helped keep the project moving through very difficult and unpredictable geological and drilling conditions. The development encompasses about 12,400 square meters and includes a 77-story tower, a 59-story tower, a five-story podium, and four contiguous basement levels. The site is underlain by a residual soil derived from a siltstone/claystone (the Kenny Hill formation), then limestone bedrock. Subsurface conditions are relatively uniform within the Kenny Hill and highly variable at the limestone surface. Extreme cases included 40-meter-tall underground caverns, 40-meter-tall pinnacles, and a 50-meter-tall underground rock ledge. Local piling practice in Kuala Lumpur involves deriving pile capacity entirely in the Kenny Hill formation to avoid the unpredictable limestone surface. However, the massive tower foundation loads and relatively shallow bedrock required the piles to be socketed in the limestone. The 77-story tower will be supported by 2.0- and 2.2-meter-diameter bored piles 50 to 100+ meters long, socketed in limestone, with working loads between 40 and 70 Meganewtons. Two Osterberg-cell load tests were used to develop a site-specific rock socket skin friction correlation with RQD. Exploratory rock probes were drilled at each pile location to design the rock socket length based on the rock quality and sloping rock conditions. The rock mass was pressure-grouted during each rock probe to improve the rock quality and fill voids in the rock.INTRODUCTIONThe Kuala Lumpur City Centre, home of the Petronas Towers and the world’s deepest foundations, will be the future home of a new supertall tower. The 77-story tower will be supported by a piled-raft foundation that relies on piles terminating in the highly erratic, karstic Kuala Lumpur limestone formation. The high building loads coupled with relatively shallow limestone across the majority of the tower footprint forced the piles to extend into the limestone."

Jan 1, 2016

By A. Luckita, A. Samtani, R. Barus, J. R. Donald, J. Syarifuddin

In conventional Rotary Kiln-Electric Furnace (RK-EF) laterite nickel processing, management of dust continues to be problematic. A more efficient processing of dust represents an opportunity for energy efficiency, increased production, and productivity. PT International Nickel Indonesia (PTI), together with Vale Base Metals Technology Development (VBMTD), has successfully developed and implemented a novel flowsheet enhancement that capitalizes on these opportunities. In the novel flowsheet, the dust recycle stream is moved forward in the RK-EF laterite nickel smelting process. The dust is injected into the kiln's main burner, as opposed to being recycled to the dryers. A similar treatment of dust is commonly practiced in the cement industry; however, application to nickel smelters has not been fully developed to date. This paper describes this dust insufflation technology, the process through which it was developed for laterite nickel processing, and summarizes the lessons learned. A key conclusion is that successful new technology development requires a multi-disciplinary team involving members from research and development, study management, engineering consulting firms, project implementation management, process technology and operations.

Jan 1, 2011

By P. Somasundaran, S. E. El-Mofty

A comparison of the IMC Anionic Process and the CLDRI Process, based on pilot plant testing of waste pebble by Jacobs Engineering is presented. Estimated costs for constructing and operating a beneficiation plant utilizing dolomite flotation are given. Research to develop practical flotation processes for removing dolomite from low-grade phosphate rock has been a high priority for the Florida Institute of Phosphate Research. The Institute funded the above pilot plant programs in 1998 and 2000. The Florida Phosphate industry currently deals with the increasing dolomite content of ore reserves by practicing selective mining. Heavy media separation plants installed at two mines to remove dolomite from pebble are not being operated. The flotation separation of dolomite from waste pebble requires that the flotation feed be ground. Grinding liberates the mineral species and produces particle sizes small enough to be floated. Only two dolomite flotation processes, the IMC Anionic Process and the CLDRI Process, have been successfully demonstrated on flotation feed that has not been deslimed after grinding. Deslimed flotation feed, relative to undeslimed feed, has improved flotation performance and reduced reagent consumption. However, for the above mention processes, undeslimed ground feed increases the yield of concentrate because the phosphate desliming losses are avoided.

Jan 1, 2002

By Lucas de A. Pontes, Lázaro A. Rohen, F. V. Carlos Maurício, Janaina da Silva Vieira, Sergio Monteiro, Dhyemila de P. Mantovani, Frederico M. Margem, Anna C. C. Neves

The lower density of the lignocellulosic fibers such as the hemp fibers and the other natural ones is one of the characteristics that allow the scientists to obtain high levels of specific properties that when compared to the properties of ordinary reinforcements gives to the hemp fibers an advantage as a material with an expressive potential in the mechanical properties area. Then, the aim of this present work is to characterize the relative density of the hemp fiber related to the water using the pycnometry technique. This technique uses the pycnometer and it is divided in two steps. In the first step the correction factor and the moisture content of the fresh hemp fiber specimen and in the other step some weightings were done such as the dry specimen (g), empty pycnometer (g), pycnometer + water (g) and pycnometer + water + specimen (g) using a digital balance with a precision scale of 0.001 g of the bran INNERSCAN. Based on these measurement and calculations using some formulations already established in previous studies, the relative density of the hemp fiber found was around 1.393 g/cm3 and the moisture content around 7.1%.

Mar 1, 2017

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By P. Favreau

"This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.IntroductionThe Noranda Technology Centre's (NTC) Environment and Mining Laboratory, in cooperation with the mining operations of the Noranda Group, is committed to the development and implementation of new technologies in the field of mineral extraction . Within the frame of its research program, the Blasting Technology Program is developing computer "" tools"" designed to assist the blasting engineer or technician. These computer "" tools"" are regrouped under a global software system called BLASTCAD.The BLASTCAD project started in 1990 at NTC. At that time computer programs designed to calculate and model various blasting parameters had been accumulated. These programs cam e from different sources and were mutually incompatible. Furthermore, they were developed as research programs with tittle effort spent on user interface. These programs are very useful, but are highly specialized, need large input files and can be quite tedious to use as ""standalone"" packages .Therefore, the situation being faced was one where all these programs were available at the Noranda Technology Centre, but not a t the operations. The two following options were then considered: 1. continue to run all the models and programs at the Noranda Technology Centre, and present results through reports to the mines, or2. regroup all the different programs under a single one that would make them share the same data base and be transported to the user. This second option is the one that was adopted; the result is BLASTCAD."

Jan 1, 1993

By Junmo Ahn

This study investigated leaching kinetics by alternative lixiviants for copper leaching from chalcopyrite (CuFeS2), the most abundant copper resource in the world. As a refractory sulfide mineral, chalcopyrite shows low copper extraction due to passivation on chalcopyrite surface. Also, decrease of copper grade with high portion chalcopyrite requires the alternative leaching procedure to increase copper recovery. Therefore, alternative lixiviants such as sulfurous acid and methanesulfonic acid (MSA) were tested for both concentrate and low grade ore to enhance copper extraction. Also, an oxidant, hydrogen peroxide, was compared to ferric to find out the improvement of leaching kinetic. In concentrate leaching tests, 30 g/L MSA showed the highest copper extraction (47%), compared to other lixiviants at 75 °C. Periodical H2O2 addition enhanced copper extraction, and above 90% of copper extraction was observed within 96 h by periodical addition of 0.6% H2O2 at 75 °C. The activation energy of chalcopyrite leaching by MSA and H2O2 achieved 40 kJ/mol, which is chemical reaction control. The results of low grade ore leaching tests indicates that no significant difference among lixiviants (H2SO4, H2SO3 and MSA) with ferric was observed, all of which achieved around 37% within 24 h at room temperature. However, significant increase of copper extraction (>80%) was observed at both 20 g/L MSA and 10 g/L H2SO4 conditions by the addition of 10% H2O2.

By R. A. Metz, Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity,' innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1992

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By Yehia El-Ibiary, M. P. Evans

One way of increasing conveyor systems productivity is by monitoring the key parameters in the systems. In this paper, a new line of smart bearings will be presented and discussed. The new bearings are capable of monitoring temperature, vibrations, and belt speed for early detection of potentially serious problems. The new smart bearings have built in sensors that are carefully integrated and protected for long life service. These bearings are going to be the key to increasing the up time of belt conveyors in the future.

Jan 1, 1996

PROF RICHARD ÅKERMAN Stockholm, Sweden DR FRANK DAWSON ADAMS Montreal, Canada PROF RICHARD BECK Friberg, Germany ANDREW CARNEGIR New York, N.Y. DR. JAMES DOUGLAS New York, N.Y. PROF HATON DE LA GOUPILLIERE Paris, France SIR ROBERT A. HADFEILD London, England PROF HANS HOFFER Leoben, Austria HERBERT C. HOOVER Leoben, Austria JAMES FURMAN KEMP New York, N.Y. PROF HENRI LOUIS LE CHATELIER Paris France EZEQUIEL ORDONEZ Mexico City, Mexico DR ROSSITER W, RAYMOND New York, N.Y. PROF RICHARD H, RICHARDS Boston Mass. DR. ING H. C. EMIL SCHROEDTER Dusseldorf, Germany JOHN E. STEAD Middlesborugh, England PROF DIMITRY CONSTANTIN TSCHERNOFF St Petersburg, Russia PROF TSUNASHIRO WADA Tokyo, Japan CHARLES D WALCOT Washingtion D.C.

Jan 1, 1923

By T. A. Ring

The bed filtration of colloidal particles has been modeled by performing a differential particle balance. The balance considered the localized particle deposition rate to be the sum of three rate resistances: 1) mass transfer to a region near the surface; 2) adhesion onto a partially filled surface; and 3) resuspension from a partially filled surface. The differential particle balance equations, one for the free particles and one for the adhered particles, were solved by a finite difference algorithm. The results of this model are compared to experimental filter breakthrough curves.

Jan 1, 1983