Search Documents

By Ivan F. Avery

DOMEST1C production of carbon black in 1963, remained at about the same level as in 1962. Carbon black produced by the furnace process increased 2 percent to 1,880 million pounds in 1963 and accounted for 91 percent of the total output. Channel black production continued to decline and was 14 percent less than a year ago. Shipments during 1963 totaled 2,098 million pounds, a 1 percent increase for the year. An increase of 88 million pounds in domestic sales was partially offset by a decrease of 72 million pounds in carbon black exports. Total value of carbon black production in 1963 was $148 million. The average value per pound was 7.18 cents or 0.12 cent per pound more than in 1962.

Jan 1, 1964

By M. B. Hopkins

FOR years the expression "except rubber, tin, and manganese" has appeared in practically every discussion of the natural resources of the United States. Knowledge that natural rubber is not produced in the United States has now spread from the relatively few who have reason to be interested in the country's basic raw material supplies to all those who ride in automobiles, which means everybody. This "everybody" reads in the daily papers that we have a stock pile of natural rubber and that plenty of synthetic rubber is just around the corner. Statistics as to the United States' rubber requirements and sources of supply are of interest to him only to arrive at an answer to the question : "After taking care of rubber requirements for military purposes, will there be rubber for my automobile and the many other rubber articles I want?" More than 30,000 different rubber articles are manufactured in addition to the tires and tubes which use up about 70 per cent of the rubber supply.

Jan 1, 1942

By Tatiana Tronda

"The territory of Belarus is characterized by nonhomogeneous ground conditions. In some cases soft ground layers can reach tens of meters in depth. Application of piles and other conventional foundations is rather difficult and expensive in such complicated conditions. Alternatively for the first time dry concrete columns were applied to improve the saturated soft soils at two sites. As there is no design methods for calculation of bases improved by dry concrete columns static penetration and static load tests were carried out to check the bases on availability. Considerable increase of toe resistance and Young modulus was achieved for all types of soil. Practical application, technology and test results are described in the paper. According to comparative calculations the cost of foundations on the base improved by dry concrete columns can be 32-75% lower than the cost of conventional pile foundations depending on ground conditions.INTRODUCTIONPile foundations, sand cushions or dewatering are usually applied in complicated ground conditions which are caused by presence of saturated soft soils. If the depth of soft soils reaches 20 m or more, conventional foundations have limited application, high labor and construction cost. A rational solution in such conditions is a ground improvement of upper soft soils. It allows the loads to be transferred on upper ground layers and the stresses to be dissipated considerably before reaching underlying soft ground layers.One of the effective ground improvement methods for saturated soft soils is the reinforcing by dry concrete columns (Fig. 1). The method allows saturated soft soils to be compacted and be drained at the same time. As a result strength and deformation characteristics of natural soils improve (Tronda 2013, ?????? 2014).Unfortunately, there is no design and computing methods for the ground improvement by means of dry concrete columns. However, at present the methods are under development on the basis of theoretical and experimental researches.TECHNOLOGYThe dry concrete columns are fulfilled in pressed wells according to technology of vibrostamped piles. Wells are pressed by vibratory hammer with the closed ended casing (Fig. 2) that provides compaction of surrounding soft soils. Then the casing is filled with dry concrete mix (Fig. 3). The casing end remains on the design depth and the casing is removed by vibratory hammer. The removing of the casing with vibration enables compaction of dry concrete mix inside the well. Dry concrete mix drains surrounding saturated soft soils improving its properties and the compaction speeds up the consolidation process. Over time the dry concrete columns fasten absorbing water from surrounding saturated soft soils that is need for hydration of cement (Fig. 4, 5)."

Jan 1, 2016

By Hossein Kazemi

This article is a review of fluid flow and mass transport in fractured rocks. The topics include: single-phase and multiple- phase flow theory, formation productivity or injectivity improvement by artificial fracturing, and mass transport associated with fracture acidizing. Possible extension and application of such ideas to in situ mining in fractured rocks are presented.

Jan 1, 1974

By Harrison Cooper, Stephen Pack

"Data from samples taken during rotary air blast and reverse circulation drilling are crucial to properly assessing economics of mineral deposits in the case of exploratory work, and are equally critical in accurately delineating ore and waste in execution of mine operation plans. Past studies of sampling procedures, comparing results of conventional splitting to more precise extraction of representative samples, illustrate the significant degree of error frequently encountered. Economic impact of error in mine blast hole sampling work can be shown to result in theoretical losses valued at millions of dollars annually in operating large scale mining projects. Results of past drill sampling studies are reviewed.Drill sampling technique can be improved by collecting coarse and fine particles together and extracting samples for assay from the complete flow of rock and dust simultaneously. This can be accomplished with a collection unit attached to the drill stem through which all except a small proportion of extreme fines are retained. The bulk mass can be static sampled as flow takes place through the collector when size reduction is not required. Alternately, collected mass with fines and coarse intermingled can be processed for increased accuracy through size reduction to obtain proportional samples."

Jan 1, 1999

By A. Hoath, V. Paul, F. Haslam McKenzie

This paper considers mining ventures occurring in rural communities in Galicia, Spain and Western Australia, Australia. It compares and contrasts the communities where mining is taking precedence over other industries, examining the potential land use conflicts and the future of both the communities and the mines currently operating there. The Galician case study, Trevinca, is located 200 km inland and was once a primary producing area, notable for its scenic alpine landscapes, which have since been developed for small scale tourism purposes. The Australian case study, Boddington is located 100 km inland in what has been a highly productive farming area. Mining was a marginal industry in the case study areas but due to the comparative devaluing of agriculture and tourism and the increased value of mining outputs, mining has increased in scale and economic importance. This paper will consider the environmental, social and economic impacts that have occurred in both the case study localities. Where there have been land use conflicts, strategies for minimising the adverse outcomes will be considered.

Jan 1, 2011

By Thomas T. Read

The cost of labor turnover in industry is so large as to justify the adoption of almost any means to bring about its reduction. Intensive study has shown that faulty methods of hiring and discharging men is the most important factor in labor turnover. Complete control over hiring and discharging by the foreman is a relic of outgrown industrial conditions; centralized hiring permits this work to be put on a scientific basis and also does away with many serious evils that cannot, otherwise be reached. Centralized hiring does not impair the authority of the foreman; he hires his men from the employment office and discharges them back to it, instead of from and to the street. The employment manager, being a direct representative of the employer, tends to restore the former relation of direct intercourse between employee and employer that was helpful in avoiding friction between them. Being a specialist,, he is able to bring special knowledge and skill to bear upon the task of selling employment in his concern to desirable workmen; he is also able to give the foreign workman the special attention he requires. Employment managers have been used for the past few years by a number of large organizations, a few of which are engaged in the mining and rnetallurgical industries. They have invariably reduced labor turnover, in some cases to as little as one-tenth of what it had been. So great a reduction is due in part to other changes made in the light of the data made available by scientific study of the labor problem. In my former paper on personnel work' I advocated the more general use of the employment manager in mining and metallurgical enterprises as a means of reducing labor turnover. The form of organization recommended seems not be to understood by all, and I have requested the privilege of explaining it at greater length, since it is perhaps the most important factor of all in personnel work, and has a vital influence on the cost sheet of every industrial enterprise.

Jan 1, 1918

A brief review of the problems in ventilating and cooling deep and hot Australian mines is presented. An overview is given on the development of the controlled partial recirculation concept. The main part of this paper describes the first majo

Jan 1, 1994

By L. Martin, M. Raffaldi, M. Stepan, D. Benton

The Office of Mine Safety and Health Research, Spokane Mining Research Division, is continuing its high-energy, high-displacement testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link mesh, welded-wire mesh and combinations of them. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can assist in interpreting the condition of installed surface support. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to better quantify the stability of installed shotcrete support.

Jan 1, 2016

By Henri-Louis Jacob

Le secteur des substances non-metalliques repose au Quebec sur !'exploitation et la transformation d'une dizaine de mineraux ainsi que sur la production de materiaux de base destines surtout a l'industrie de la construction. L'ensemble de cette production representait en 1982 une valeur estimee a plus de 797 millions $, soit tout pres de 400Jo de la production minerale du Quebec. L'amiante et Jes scories de titane destines a la production de pigments, qui comptent parmi Jes plus importantes substances minerales produites au Quebec, representent respectivement 370Jo et I 70Jo de la valeur totale des non-metalliques tandis que le groupe des materiaux de construction represente pres de 400Jo. Les autres substances, parmi lesquelles ressortent nettement la tourbe, la silice et la magnesite, representent une valeur totale de 61.5 millions $.

Jan 1, 1984

By W. H. Hoffman

At the Glen Summit meeting (Trans., xx., 605) I described in a general way the grinding-machine known as the Sturtevant mill, built by the Sturtevant Mill Co., of Boston, Mass. My first experiments in granulating magnetic. iron-ores with this machine were made five years ago in the northern portion of New York State.

Jan 1, 1893

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By Curt Swanson, David C. Mathy, Dru R. Nielson, Kent VonAspern

In 1997, Central Contra Costa Sanitary District undertook the design of the Martinez East Side Trunk Sewer Improvements Project. Microtunneling was specified for approximately 1,035 meters (3,400 feet) of 600-mm (24-inch)diameter pipeline to be installed through estuarine soil deposits (San Francisco Bay Mud) and alluvium beneath the congested city streets of downtown Martinez, California. Directional drilling was specified for approximately 275 meters (900feet) of 200-mm (8-inch) diameter pipeline in four separate segments to be drilled through bedrock within narrow utility easements between residential properties. This paper presents a case history for the design and construction of themicrotunneling and directional drilling aspects of the project.

Jan 1, 1999

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of U.S. coal mining companies are beginning to develop coal seams previously thought to be coo deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas contained in coal beds increases with depth, and ventilation requirements are much more stringent for deep underground coal mines than for shallower mines. When the longwall mining method is used at great depths, ventilation, ground control, and operational considerations must all be addressed in the design of longwall panels. This paper examines the influence of these factors, particularly ventilation and operational considerations, upon the feasibility of two, three, and four-entry longwall development panels in Jim Walter Resources' four deep mines.

Jan 1, 1986

Prof. Henry S. Jacoby, Cornell University,Ithaca, N.Y. (communication to the Secretary): When a simple beam supports any given load, the lower fibers me in tension while the upper fibers are in compression, and if its cross-section is rectangular the neutral surface, where the stresses pass through zero from tension to compression, is at mid-depth, provided the elastic limit is not exceeded. In addition to the longitudinal stresses, there are horizontal shearing-stresses between the fibers which have their maximum value in the neutral surface, and which equal zero at the upper and lower surfaces, while there are also vertical shearing-stresses. Let another beam of the same dimensions be placed on top of this one, and the load be doubled, it then produces stresses in each beam of the same character, magnitude and distribution as in the preceding case, provided there be no friction between the adjacent surfaces of the beams. Next let these two beams be so firmly united that there will be no motion between them when the same load is again applied. All the fibers in the upper beam are now in compression, and those in the lower beam in tension, while the maximum stresses in the outer fibers are only one-half as large as before. The strength of the combined beams is therefore doubled. If, however, some motion occurs between the beams, then the stresses in some of the lower fibers of the upper beam pass from compression to tension, and those in some of the upper fibers of the lower beam from tension to compression, while the stresses in the outer fibers have a magnitude between the two values previously stated. These fundamental facts relating to the flexure of beams indicate the necessity of carefully designing the keys or brace-

Jan 1, 1898

By Fangming Liu

The key problems of current flowsheets and equipments are analyzed. A new steel slag's crushing flowsheet whose key equipments are the improved inertia cone crusher and inertia vibrating jaw crusher is proposed. An advanced two stage open-circuit crushing method is adopted in the flowsheet, with 90% of particle size crushing under 6mm. Using inertia vibrating technology and selective crushing principle the crushers can realize steel slag separating fully into steel and slag and with flexible transmission mechanism the crusher can be protected when iron lump is passing. The flowsheets can enhance the recovery of metal greatly, and expand the application range of tail slag and added value.

Sep 1, 2012

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector is one of the leading sectors where work accidents are most intense because of the constant change of work environment and heavy working conditions. The losses and the halt of production after the accident negatively affect productivity and production efficiency. It has been found that there are very few studies on the use of Data Envelopment Analysis (DEA), which is one of the nonparametric efficiency analysis methods, in the evaluation of mining sector occupational accidents. According to parametric activity measurement methods, it has been tried to show that the DEA can also offer the opportunity to interpret work accidents by taking advantage of its advantages. Due to the application of open-pit mining methods along with underground working techniques which increase the risk factors with respect to accidents at work that occurred between 2012 and 2018 of Western Lignite Corporation (WLC) were tried to be analyzed in the present work. As a result of the analytical work using Data Envelopment Analysis (DEA) for the years 2014, 2015, 2016, 2017, and 2018, inefficiency has been determined in both underground and surface operations. According to the results obtained, it was determined that WLC could not produce enough production in both the underground and surface coal mining operation, despite the accidents that occurred, while it had the opportunity to produce more. In addition, it was found that the increase in accidents occurred more than the increase in the amount of production during the years studied.

Jul 4, 2021

By William C. Miller

This report describes investigations by the Bureau of Mines designed to establish the noise level and spectrum of various types of pneumatic rock drills and to furnish information that would be useful in conducting sound measurements in mining environments and in reducing the noise generated in pneumatic drilling. These investigations show that (1) the noise generated by the drills in the frequencies below 100 cps is caused by the impact of the piston and drill steel, in the frequency range between 100 and 2,000 cps by the exhausting of air from the ports, and in the frequencies above 2,000 cps by the resonant frequencies of steel drill parts and of drill steel; (2) satisfactory instruments and instrumentation systems are available for field and laboratory measurements; (3) reliable sound measurements can be made in mining environments; and (4) devices can be developed that will abate the noise.

Jan 1, 1963

By Jan Pan, Deqing Zhu, Xianlin Zhou, Yanhong Luo, Zixing Xue

"Magnetic roasting process, aiming at obtaining magnetite concentrate, is the principle method of exploiting siderite as a raw material in iron and steel industry. Study on preparing DRI from siderite through coal based reduction technology is sporadic. To make the process of how siderite is reduced to iron clear, roasted ore reduced from siderite by lignite under different time periods were analyzed. The results indicated that: at the temperature of 1050°C, siderite was rapidly decomposed into magnetite, and further reduced as Fe30r?FeO?Fe, the later step was slower than the previous one. A fracture of particles was found during the process of thermal decomposition and the reduction of newly formed magnetite. As the reduction proceeded, metallization rate of products increased, and the iron grain grew along with time.IntroductionWith the rapid development of economy, China demands more and more iron ores for the iron and steel industry. China has rich iron ore resources, but 97% of them are below 30% in iron grade, many are refractory and unutilized [1], therefore large quantities of imported iron ores are in a desperate need. China imported 686 million tons of iron ore in 2011 (data from the China Customs), accounting for nearly 60% of the total consumption. To guarantee the healthy development of iron and steel industry, domestic refractory iron ores have to be utilized both economically and environmentally."

Jan 1, 2013