Search Documents

By K E. Mudzanani, T A. M Msagati, D T. Maiga, T T. Phadi, M R. Letsoal, B M. Chabalala, S W. Limani

This paper addresses critical environmental, health, regulatory and scientific concerns related to gold mining activities in the specific area of Barberton, Mpumalanga, South Africa. The paper thus calls for informed decisions to be made by the authorities to safeguard both the environment and people’s health. The novelty of this study is based on its comprehensive nature of the simultaneous assessment of both cyanide and potential toxic elements (PTEs) in tailings, while taking into account their composition variability over time. By combining these aspects, it is then possible to provide a holistic understanding of the contamination risks associated with mining tailings and thus justify the need for regular monitoring and supervision to ensure compliance against regulatory limits. Additionally, this paper considered investigating the dynamic nature of tailings, which are subject to changes in their chemical composition due to exposure to weathering by various agents. In this study, the determination of weak acid dissociable (WAD) and free cyanide in tailings was performed using a validated method employing the South African Council for Mineral Technology (MINTEK) Laboratory Cynoprobe. The PTEs in tailings were determined by an inductively coupled plasma optical emission spectrometer (ICP-OES). The results revealed that the tailings contained primarily substantial amounts of PTEs, including Fe (87 566 to 37 800 mg/L), Cu (271 to 110 mg/L), Mn (2100 to 680 mg/L), Ni (400 to 390 mg/L), Zn (180 to 68 mg/L), Cr (645 to 510 mg/L), As (450 to 128 mg/L), and Pb (up to 35 mg/L). The cyanide concentrations in tailings varied between 0.20 mg/L and 0.26 mg/L for free CN (with a mean of 0.23 mg/L in water leaching), 0.23 mg/L to 0.28 mg/L for free CN (with a mean of 0.25 mg/L in alkali leaching), 0.24 mg/L to 0.35 mg/L for WAD CN (with a mean of 0.28 mg/L in water leaching), and 0.31 mg/L to 0.39 mg/L for WAD CN (with a mean of 0.35 mg/L in alkali leaching). The measured concentration of cyanide and the PTEs was compared to the minimum permissible levels enforced by the South African Department of Water and Sanitation (DWS) and the Water Research Commission (WRC) regulations that govern the disposal of hazardous constituents into the environment. Additionally, it was observed that the concentrations of contaminants in the tailings exceeded the acceptable minimum limits for hazardous waste exposure, posing risks to the environment and human health.

Apr 16, 2024

By G. Barbery

The models for particle composition prediction that have been put forward are limited to simple textures and lead to an independance of grade with respect to particle size in broken ore. A presentation is made of a modification in texture description; binary textures, in which each subeonstituent has its own breakage characteristics are introduced. The calibration of the textural model can be made using heavy liquid separation results. The application to the case of coal is presented. Coal washability data present spe¬cial difficulty due to the distribution in the specific gravity of coal, which must be taken into account. Coal s.g. distribution is taken as a generalized exponential distribution. Model calibration is then possible and is shown to be in good agreement with experimental data.

Jan 1, 1987

C. N. FEnner, New York City (communication to the Secretary) : A possible explanation of some of the' phenomena of amalgamation cited by Mr. Bayliss and others has occurred to me. We know that if, to a quantity of mercury, gold and silver are added until a putty-like paste is formed, and if this mass is spread on a flat surface and pressure is applied, a more fluid portion of the mercury will be squeezed out from the rest, carrying gold and silver with it. The proportion of gold to silver will depend, I think, upon various causes and conditions—the relative chemical affinity which gold and silver have for mercury; the amount of pressure used; the presence of other metals:

Jan 1, 1898

By Bogdan Petkovic, Boban Todorovic

In the early 90's a completely unknown problem was encountered at the converter Department: it was a chronic shortage of the cold copper charge needed for the second operating period. A high temperature operating regime was caused which further provoked a chain of consequences such as a drastic drop of the number of operations in campaigns. The consumption of repair bricks reached the quantity of 8.3955 kg / tonne of anode Cu. In 1994, we won the process of cold material smelting during the "copper" blowing [2]. The number of operations per campaign reached 180-200 again. Also in 1994 we won the process of smelting cold materials to obtain "tin" blowing with the purpose of completing their processing cycle [2]. During the period 1994 – 2007 a total of 107,845 tonnes of cold material were remelted to make copper and 56,794 tonnes were re-smelted to obtain "tin". Upon synthesizing these two processes, a completely new model was achieved in 2005, by Bogdan Petkovic, which entirely utilized all available energy of the Peirce-Smith (PS) converters of the Bor Copper Smelter and now represents the basis of the time cycle. The cold material now enters the converter plant, copper recovery is increased and the method itself is environmentally friendly. 167

Jan 1, 2009

By S. L. Gertsman

Canadian steel foundry practice has made marked progress during the past decade. Equipment suppliers, development engineers, and foundry personnel have focussed their attention on every phase of the foundry operation, with a resulting lower demand on manpower and materials. Also, more rigid specification requirements as to dimensional tolerances and quality have necessitated improvement and increased control at every stage from the pattern shop to the cleaning room. The growing trend toward mechanization is clearly evident. Equipment such as sand mixers, sand reclamation systems, material handling devices, moulding machines, core blowers, etc., is being increasingly employed by the steel foundryman. This equipment not only increases production but also tends to lessen the human variable so prevalent and disconcerting in the early days of steel founding. The result has been an improved and more reliable steel casting, which is gradually obtaining wider acceptance by design engineers. The purpose of this paper is to discuss briefly some of the practices being used, and also the direction of development that is being pursued by Canadian steel foundrymen.

Jan 1, 1948

By Arthur B. Johnson

Potassium, is one of the three basic plant nutrients along with nitrogen and phosphorus. There is no substitute for potassium compounds in agriculture; they are essential to maintain and expand food production. Potash is found throughout the world in both soluble and insoluble forms. It is only the soluble forms that are economically attractive to process, primarily chlorides and sulfates, with potassium chloride by far the most important potash salt. Sylvinite ore, a mechanical mixture of sylvite (KCl) and halite (NaCl), is a natural mineral of potassium. This ore is found in commercial quantities in the Permian sin region near Carlsbad, New Mexico. Vast tonnages of high-grade de, low-clay-content ores have been mined and concentrated during the past 40 years; however, these deposits are rapidly being depleted leaving high-clay, low-grade ore reserves of over 135 million tons. These ores, containing 13 to 22 percent K20 and 3 to 8 percent clay slimes; cannot be effectively processed by current commercial flotation methods. The present concentration processes for potash minerals in Carlsbad relate mainly to ores containing 1 percent or less of clay-slimes with a K20 content of 20 to 25 percent to yield products to meet the requirements of the agriculture market, namely, 95 percent KC1 equivalent to 60 percent K20. Discoveries of potash ore in Saskatchewan, Canada, have shifted the emphasis on expansion outside the United States. Presently, the American companies are looking to Canada for future growth, expenditures, and expansion. Four of the seven companies operating near Carlsbad are produces of Canadian potash despite the large investment sons required for shaft sinking and milling installations.

Jan 1, 1970

By Tracy Lucas, Ian Hamill

"Issues of importance in the area of continuous casting centre around product quality. This can be affected by particle inclusions transported into the mould from upstream processes and by draw-down of particles from the meniscus. Turbulence of the meniscus can increase the latter and is also detrimental to product surface quality.Suitably validated Computational Fluid Dynamics (CFD) modelling can provide the operator with an efficient tool with which to investigate the effects of changes to the design and operation of the caster and associated plant.In this paper, examples are presented of the use of the CFD software, CFX, to simulate:•,free-surface shape and turbulence in the mould using deforming meshes•,solidification in the mould using a fixed-grid, source-based method•,argon gas injection through a submerged entry nozzle using a full multiphase model•,inclusion motion and removal in tundishes using an algebraic slip model.The CFD simulations of the free surface shape are complemented by detailed Particle Image Velocimetry measurements performed on a full-size water model of a thin-slab mould and upper strand. Close agreement is demonstrated between the predictions and experiments."

Jan 1, 1999

By Minh H. Pham

This paper presents a technique for imaging the extent of solidification of molten metal flowing in a cooled pipe based on the concept of eddy currents. A 3D mathematical model, which relates the geometry of solidification to the scattered field induced in a solenoid external to the pipe, is derived. The model is described by a set of integral equations which are solved numerically using the moments method. An iterative algorithm is developed to reconstruct the solidification distribution image. Experimental measurements have shown that the eddy current technique is sufficiently sensitive for practical purposes.

Jan 1, 2001

OFFICERS OF THE WOMAN'S AUXILIARY AIME President-Mrs Robert D Coombs, 375 Paramus Road, Paramus, N J First Vice-President-Mrs W McG Peirce, Troy Court 73 F, New England Avenue, Sum¬mit, N J Second Vice-President-Mrs Andrew E Beer, Richardson Avenue, Sea Cliff, Long Island, N Y Third Vice-President-Mrs Ira T Hook, 494 Norton Parkway, New Haven, Conn Fourth Vice-President-Mrs John R Kenney, 427 W Wrightwood Avenue, Chicago 14, Ill Fifth Vice-President-Mrs Alfonso Ballon, Montero Rosas 115, Barranco, Lima, Peru Recording Secretary-Mrs Arnold H Miller, 601 West 115th St, New York 25, N Y Assistant Recording Secretary-Mrs R J Mechin, 66 East 79th Street, New York 21, N Y Corresponding Secretary-Mrs Theodore Nagel, 76 Remsen St, Brooklyn 1, N Y Treasurer-Mrs Robert W Rowen, 116 East 68th St, New York 21, N Y Assistant Treasurer-Mrs Samuel H Dolbear, 11 Broadway, New York 4, N Y Assistant Treasurer-Mrs H A Kursell, 12 Murray Hill Road, Scarsdale, N Y

Jan 1, 1956

By Yufeng Guo, Tao Jiang, Jianjun Fan, Haizheng Hao

"Function of High Pressure Roll Grinding (HPRG) in production of oxidized pellets from magnetite concentrate as raw material was systematically studied. It was found that bentonite dosage decreased from 1.3% to 0.8% if specific surface area of magnetite concentrate pretreated by HPRG was up to 2553.41cm2.g-1. The green ball quality improved obviously due to the increase of specific surface area and fine particles content, and the improvements of size distribution and the ballability of pretreated materials. However, the decrease of pellet porosity accelerated the primary solid phase reaction and oxidation reaction, which made the pellets surface form compacted layer that handicapped the diffusion and migration of oxygen, promoting the formation of double layer structure of finished pellet. Consequently, the compression strength of preheated and roasted pellets was not markedly improved by HPRG.IntroductionWith the increase of proportion of pellets in the BF recently, the technical-economic index of BF has obviously been improved. Consequently, the production and the quality of BF pellet are given more attention [1]. However, with the decrease of the quality of iron ore concentrate, the problems such as poor ballability, high bentonite dosage, high preheating and roasting temperature are becoming the great challenges to not only the quality of finished pellets, but also the energy consumption [2, 3]. In order to overcome these problems, mechanical pretreating technologies such as the High Pressure Roll Grinding (HPRG) and Damp-grinding are widely applied. HPRG has a number of advantages such as low energy consumption, high productivity and easy-maintaining. It is more economic and environmentally friendly than the Damp-grinding technology [4, 5]. A great number of experiments have revealed that HPRG can improve the quality of hematite pellets. Although there are some studies of function of HPRG in the magnetite oxidized pellet production, they are not comprehensive and systematic, especially to the preheating and roasting system [1, 2, 6, 7]. Accordingly, the influence of HPRG on the pelletizing system and the preheating and roasting system are systematically studied in production of magnetite oxidized pellets in this article."

Jan 1, 2011

By Christoph Zschiesche

Managing complex material streams within a lead smelting/reduction process has a long history at Aurubis. After modernization of the secondary lead smelter in 1991, Aurubis operates an electric furnace and a Peirce Smith converter to process complex secondary materials. This process links the copper and the lead metallurgy allowing Aurubis to properly combine primary and secondary process lines to optimize the processing of complex raw materials and smelter intermediates. However, combination of copper and lead metallurgy processing requires a continuous evaluation as raw material quality and composition varies. This paper describes Aurubis lead smelter processing and provides some fundamental considerations to optimize the lead processing, in particular with aspects related to speiss formation

By D. W. Butner

This Information Circular , one of a series published by the Bureau of Mines , reports on the methods and costs of mining and concentrating zinclead ore at the Highland Surprise mine in the Pine Creek area of the Coeur d'Alene region of Idaho . The mine is owned and operated by the Highland Surprise Consolidated Mining Co. , which supervises operations of the Nevada Stewart group of claims , which is adjacent on the northwest . These properties are at the extreme eastern end of a zone of fracturing that strikes northwest across the Pine Creek area . In fractures along this zone are the principal Pine Creek mines ; these are the Highland Surprise , Nevada Stewart , Sidney , Denver , V and Idaho , Liberal King , and Northern Light . Country rock at the Highland Surprise is argillite of the Prichard formation (Belt series ) . Fracturing has permitted the movement of mineral- izing agents that have replaced adjacent walls and crushed country rock with sulfides . Ore minerals are sphalerite and galena with accessory pyrite , chalcopyrite , pyrrhotite , and siderite . Three principal ore shoots were found on the Highland Surprise property . The Highland ore shoot was mined from outcrop to the 400 level . The Surprise ore body has been developed to a depth of 1,400 feet on the dip of the vein . The outcrop of the Surprise ore shoot was 150 feet long and 2 to 4 feet thick ; on the 1,150 ( lowest ) level , the ore shoot is 320 feet long and 10 to 17 feet thick , with good zinc content . Surprise ore shoot No. 2 occurs 250 feet west of No. 1 and has been mined from the 500 to the 1,000 level . From 353,000 tons of ore mined between 1910 and 1948 , the property has a recorded production of 256,000 ounces of silver , 7,500 tons of lead , 24,000 tons of zinc , and 412 tons of copper . Both shrinkage and cut and fill stoping methods are used at the Highland Surprise , but shrinkage is unsuitable for mining below the 700 level , because faulting has weakened the walls . Development of the Surprise ore , as well as exploration laterally and along the strike , is prosecuted steadily . A prospect heading is being pushed westward toward Nevada Stewart ground from the 700 level . The mill has a rated capacity of 275 tons per day and operates near capacity . Selective flotation makes zinc concentrate that is shipped to the Anaconda smelter and lead concentrate that is trucked to the Bunker Hill smelter at Kellogg .

Mar 1, 1950

By G. Y. Chin, W. L. Mammel

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain has been analyzed by Taylor and by Bishop and Hill. The Taylor analysis is based on a principle of' virtual work, and involves finding, among numerous cotnbinalions of slip systems that satisfy the imposed strain, the combination in which the sum of the glide shears is a minimum. Previously, Taylor has treated the case of axisymmetric flow when slip occurs on (111)(110) (or {110)(111)) systems only. His analysis has now been extended by computer methods to the cases of slip on {112}(111) and {123)(111) systerns and of mixed slip on {110), {1 12), and (123) planes with a common (111) slip direction, all of which are important in the deformation of bcc crystals. The results are computer-plotted as contours of the ratio of the floe strength to the critical resolved slzea-r stress for slip, for axial orientations distributed throughout the standard stereographic triangle. Implications of the computer results to texture develop,merit, texture hardening, and dislocation theories oj work hardening are discussed. WhEN a single crystal is extended in the usual tension test, the lateral dimensions can change relatively freely. In this case, the glide shear produced by slip on a single slip system is sufficient to accommodate the (tensile) deformation. Since slip is governed by a critical resolved shear stress law (the Schmid law'), the single active slip system is one for which the stress, resolved on the slip plane and in the slip direction, is the highest among the several equivalent slip systems. This amounts to saying that a value M = U/t = y/~ is a minimum among the equivalent systems, where M is the inverse of the familiar Schmid factor (a and E refer to tensile stress and strain, and T and y refer to resolved shear stress and shear strain). A grain embedded in a polycrystalline aggregate, on the other hand, cannot freely change its shape due to constraint from its neighbors. In this case, slip from five independent slip systems (to accommodate five independent strains) is generally required.' Based on the principle of virtual work and assuming that the critical resolved shear stress for slip is the same for all systems, Taylor hypothesized that, among all combinations of (five) slip systems which are capable of accommodating the imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Again, this is equivalent to saying that the value of M = CjlyjI/ is a minimum, in analogy to the single slip case. Taylor aminimum,analyzed the case of {111)(110) slip for fcc metals, and applied the analysis to crystals undergoing axisymmetric flow, that is, the same macroscopic shape change as the poly crystalline aggregate under uniaxial tension (or compression). For the twelve equivalent {111}( 110) slip systems, there are 384 independent combinations of selecting five systems to satisfy the five independent linear equations of imposed strain.4 Taylor calculated the value of M for each combination* and obtained the active com- *A number of the independent combinations were omitted from consideration in Taylor's original work (see Ref. 5). bination (minimum M) for a number of axial orientations distributed throughout the standard stereographic triangle. Later work by Bishop and Hill*'8 showed that Taylor's least-shear hypothesis was equivalent to a maximum work principle which they advanced. Using the simplified Bishop and Hill method for {111)(110) slip, Hosford and Backofen' obtained detailed contours of constant minimum M for the same axisymmetric flow case. In contrast to {111}(110) slip in fcc metals, slip in bcc metals is generally described as occurring on {ll~)(lll), {112)(111), {123) (111) systems as well as mixed slip composed of all three. Since the direction cosines of the slip plane normal and the slip direction enter as a product in the Taylor analysis, the Taylor solutions of ,M for {110)(111) slip are identical to those for { 111} 110) slip. The other three cases of slip, however, have not been solved. In view of the numerous combinations of slip systems involved in the calculations, the Taylor analysis is clearly oriented toward computerized solutions. THE TAYLOR ANALYSIS In order to obtain the active combination of (five) slip systems by solving for the minimum value of M = we first express the (small) strain components E,, with respect to the cubic axes 1, 2, 3 ([loo], [010], [001], respectively) of the crystal, in terms of the sum of the glide shears yj from slip systems j: where n, and n,j refer to direction cosines of the slip plane normal, and dri and dsi to direction cosines of the slip direction, of slip system j, all referred to the cubic axes. In practice, the strain components are given with respect to the specimen axes X, y, 2. These components are readily converted to ers through the tensor transformation where irk and 1,~ are the direction cosines between the two sets of coordinate axes.

Jan 1, 1968

By A Mooney, J Marsden, H Grosser, G Dunstan

Carrapateena is a copper-gold deposit hosted in a brecciated granite complex, located 500km North of Adelaide, South Australia. The deposit is being mined using the Sub Level Caving (SLC) Mining method at a rate of 4.25 MTPA. The Carrapateena SLC construction was completed in Q4 2019, with ramp up to a mine production rate of 4.25 MTPA completed within 12 months; ~ 6 months earlier than originally planned (OZ Minerals, 2020b). Traditional SLC designs have had issues with safety interactions on production levels, namely at the perimeter drive, as well as presented challenges for the application of automation due to frequency of activity required to achieve ring turnover rates. Safety in design provides an opportunity to learn from experience at recent modern SLC operations and by considering hazards early in the design process minimise exposure and improve safety, productivity and automation of mining activity. This paper discusses the work carried out during the Carrapateena feasibility study and optimised during project execution; to update the SLC production level mine design, with a layout known as the Carrapateena Crows Foot Level Layout. This paper focuses on: • An introduction to the Carrapateena Operation and mine plan. • An overview and historical challenges of traditional level layout. • An introduction to the Carrapateena Crows Foot level layout, including production level design parameters as well as development metres and productivity comparisons. • Outlines the benefits of the Crows Foot design for safety in design of SLC operations. Provides a roadmap for improved production efficiency, level operational philosophy and the application of automation within the SLC.

Mar 15, 2021

By Gonzalez-Dominguez J. A, Dreisinger D. B

At Cominco's Zinc Refinery at Trail, British Columbia impurities are removed from zinc sulphate electrolyte by a two-stage purification process using zinc dust. Copper, cadmium and thallium are removed in the first stage whereas cobalt is removed in the second stage. Cobalt removal kinetics are affected by soluble antimony and copper additions to the electrolyte. This study was focused on the kinetics of cobalt removal by zinc powder cementation. Experimental variables included copper and antimony concentrations, pH and temperature. Common organic additives employed in zinc plants were studied to determine potential interactions with the cobalt removal process. Cementation products obtained from laboratory experiments and plant practice were studied using SEM. A number of significant results were obtained: 1. Copper and antimony ions were sustantially removed from solution during the early stages of the cementation reaction (within the first 15 minutes). Cobalt cementation kinetics are slow and follow a first order kinetic regime. 2. A drop in the cobalt removal rates can be correlated with a rise in the Eh of the slurry. 3. Ligninsulphonate, Percol 351 and animal glue at levels of 2 mg/L significantly impede cobalt cementation.

Jan 1, 1993

By Jay A. Carpenter

THIS preliminary report from the Committee to Study Relations Between Students and the Institute is submitted to our member- ship for consideration and discussion before the general subject comes up for action at the Annual Meeting in February. At present, the A. I. M. E. has a dual relationship with mining students, each relationship in no may connected with the other. To the individual student the Institute offers for $2 a year a Student Associateship in the Institute which carries with it a subscription to MINING AND METAL- 'LURGY, a watch fob, and the privilege of becoming a Junior Member after graduation without payment of the -first year's dues, if one's application is accepted. To the student's college society it offers the privilege, upon application, of becoming 'an Affiliated 'Society, which brings with it no specific supervision or aid, and in turn requires no specific conditions as to membership, fees, or rules. This Affiliated Society is distinctly a school organization which Student Associateship in the Institute can he given special status or ignored, is the local .society sees fit.

Jan 1, 1934

By R. Hurman Eric

The dew-point technique of activity measurements take advantage of the volatility of a component in solution. The pressure of the volatile component over a sample is determined from observations of the temperature at which condensation of the vapor occurs. The method is applicable best when the vapor pressure of the components would differ by about two to three orders of magnitude. Experimentally, this is a closed system involving the use of evacuated and sealed transparent quartz sample probes. Furthermore reliable vapor pressure data of the volatile component is essential along with a specialized high temperature furnace capable of giving reproducible results. In this context, the vertical Dew-Point Furnace (DPF) was designed and built after elaborate trails until enough proficiency was gained for reproducible results. Over the years the DPF was modified and improved. The DPF developed was versatile and could easily be used for activity measurements in the isopiestic mode (another method of measuring activities of a volatile component in a solution). The necessary ancillary systems; namely evacuation-flushing-evacuation followed by sealing of quartz sample probes under vacuum were also perfected over the years. As and when necessary the dew-point technique was supplemented by classical equilibration-quenching method employed on the sealed quartz sample probes to reveal necessary phase equilibrium information. The following were studied utilizing the above technique: (i) Activities in CU2S-PbS and FeS-PbS binaries and CU2S-FeS- PbS ternary at 1200°C; (ii) Activities in Cu2S-SnS and FeS-SnS binaries and Cu2S-FeS-SnS ternary at I200°C; (iii) Phase equilibria and thermodynamic in Cu-Pb-S, Fe-Pb-S, Fe-Sn-S, Cu-Sn-S and Ag-Sn-S systems. Most recently the following systems have been tackled: (i) Phase equilibria and thermodynamics in the Ag-Pb-S and Sn-Pb-S systems; and (ii) Activities in Ag2S-FeS-CuzS-PbS quaternary at 1200°C.

Jan 1, 2003

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949