Search Documents

By W. E. Keck, Paul Jasberg

The flotative properties of the principal minerals in Michigan's potential iron ores have been investigated to develop methods of bene-ficiation for the ores. One of these minerals, magnetite, is of considerable importance as a source of iron. Study of its flotation was similar to that of hematite1, another iron mineral in these potential ores. The present research consisted essentially of: (1) a survey of the literature on magnetite flotation, (2) the preparation of pure magnetite, (3) the development of laboratory procedure and (4) flotation experimentation. Literature on Magnetite Flotation.—For the purpose of this discussion, the results of previous work on the flotation of magnetite can be summarized as follows. The mineral has been floated with pine oil2, and it has also been separated from synthetic mixtures with silicates by the use of the same reagent2. Magnetite and apatite in iron-ore slimes have been separated by flotation of apatite with sodium palmitate3. These data were utilized in the present investigation. Preparation of Magnetite.—The pure mineral was prepared from the magnetic-separator concentrate of an iron ore (obtained from the Wither-bee Sherman Corporation, Port Henry, N. Y.). This concentrate was slowly comminuted with laboratory rolls and pulverizer to pass 65-mesh and was then tabled several times. Tabling yielded a relatively coarse magnetite concentrate, tailing and slimes. The two latter materials were rejected insofar as the present work is concerned, and treatment of the magnetite (table concentrate) was continued by separating it into — 65 + 200 and — 200-mesh sizes. Separation of the sizes was made by first dry screening and then wet screening. The —200-mesh material was rejected to eliminate possible introduction of error into flotation

Jan 1, 1939

By Thomas H. Dubaniewicz

Fiber optic systems are being deployed in locations where explosive gas atmospheres are normally present or are present under fault conditions. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (NIOSH, PRL) conducted a study of laser safety in potentially flammable environments. Researchers conducted experiments to estimate the mean and standard deviation of laser powers needed to ignite 6% methane-air atmospheres using single mode optical fiber tips covered by two types of iron oxide (Fe304 and (FeMn)203) mixed with a ceramic adhesive. The iron oxides, heated by a 1064 nm continuous wave laser, ignited the methane-air mixtures ,at similar powers. The minimum igniting power and maximum non-igniting power (10 tests) were 407 and 350 mW, respectively, using a 62.5 pm fiber. Laser beams guided by 125 and 80 pm diameter cladding single mode fibers produced similar methane-air igniting powers. Ignition was not observed using coal particles at powers that produced ignition with the iron oxides. Threshold ignition delays using the single mode fiber were approxinlately proportional to the inverse square of the igniting power. Ignition delays were significantly longer than the reported activation time for a comnlercial fiber optic power limiter. Comparisons are made with the results of other researchers. Published by Elsevier Ltd.

By Dao Dac Tao

The Vietnam coal industry in recent years has achieved the rapid growth. However, in the process of industrialization and modernization of the country, the demand for coal for energy is constantly increasing. This paper presents the Vietnam coal industry in the last stage: the opportunities and challenges facing the coal industry as it strives to become modern, highly effective and capable of meeting the demands of national energy security, all in harmony with socio-economic and environmental needs.

Aug 1, 2013

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of synthetic rutile—a common starting material for most titanium production processes—from iron-rich titanium minerals such as pseudorutile and ilmenite is described. The process for “upgrading” the mineral to synthetic rutile is by carbothermal reduction of the mineral while immersed in a molten salt at high temperature, followed by magnetic separation of the reduced iron. A variety of factors are also investigated, such as particle size of the mineral, the type of mineral, and the molten salt used. The solubility of iron(III) oxide in different molten salts is also experimentally determined.

Jan 1, 2016

By Joshua Hoffman, Rob Farnfield, Catherine Johnson, Braden Lusk, Morgan Lane

IMESAFR (IME Safety Analysis for Risk) is a quantitative risk assessment software tool developed by the Institute of Makers of Explosives (IME) and A-P-T Research, Inc. It is used for managing risk in the commercial explosives industry, the newest version of the software was completed in 2012. This paper discusses the use of this software package in conjunction with data collected for a television series on the reenactment of the ‘London Blitz’, a 57-day bombing of the City of London in 1940. In this reenactment, purpose built structures using period design and materials were constructed at a test facility in the North of England. Five devices ranging in size from 20 kg (44 lb) to 1100 kg (2400 lb) were detonated at varying distances from the structures; each blast was monitored by EPC-UK and the resulting structural damage was analyzed. Data recorded from the blasts included high-speed videos, photographs before and after each event and air overpressure readings. The same data was inputted into the IMESAFR software package to assess the risk imposed on the residents of London during this time. The appropriateness of this tool for evaluating structures built using historical practices is discussed. Data from the full scale tests is compared to effects predicted by IMESAFR. Further analysis of the risk recommendations produced by IMESAFR is compared to the actual damage assessed during the large scale tests.

Jan 1, 2014

By Lucas Tedesco Bolzan

Blindagens contra armas de fogo são de grande importância para proteção do homem, no contexto atual de violência urbana e conflitos armados. Destacam-se os sistemas de blindagem multicamada (SBMs), constituídos por materiais diferentes, pelo seu bom desempenho e menor peso. Um SBM típico é constituído de uma camada cerâmica frontal, uma segunda camada de compósito e uma camada posterior de metal dúctil. Apesar de serem tipicamente fabricados em materiais sintéticos, uma alternativa é a utilização de compósitos reforçados com fibras naturais como segunda camada. Este trabalho tem como objetivo verificar a eficiência de SBMs que utilizam compósitos de poliéster com 30%vol. de fibras ou tecido de sisal. Foram realizados ensaios balísticos com munição 7,62 mm, e verificou-se que os SBMs com fibras e tecido de sisal se enquadram no critério da norma internacional (NIJ 0101.06), de resistir ao impacto balístico e imprimir deformação menor que 44 mm no material de referência (plastilina), além de manterem sua integridade após o impacto.

Aug 17, 2017

By Z. L. Huang

A new porous apatite product was prepared using phosphorite from Yichang China by a tem-plate-directed method in self-made reaction equipment under constant temperature and pressure. The product was characterized by XRD, FT-IR and SEM. The results showed that the product was a kind of micrometer porous sphere three-dimensionally structured by apatite nanoflakes, that the average thickness of nanoflakes was about 50 nm, that the average pore size was about 1.2 µm and that the particle average size was about 20 µm. Great amounts of Ca2+channel, high special surface area and regular spherical shape show the potential promising applications of this special porous apatite product in the fields of catalyst, medication, chemical engineering and environment engineering

Jan 1, 2014

By S. Chuanyao

In last decade, along with its booming Chinese economy, China?s higher education has experienced rapid growth. In 2010, the number of various colleges totals more than 3500, with 2.2 million faculties registered. Currently there are almost 30 million students studying in the colleges, 3 times more than 10 years ago. Mineral Processing was initiated in 1949 as a sub-discipline of Mining Engineering, one of the 13 first level disciplines. Mineral Processing is now established in 34 Chinese colleges, recruiting 2600 undergraduate students, 540 postgraduate students and 100 PhD students every year. A further 9 institutes offer postgraduate education in this field. More than 3000 graduates majoring in Mineral Processing join the industry or institutions each year. The four-year undergraduate teaching and practical training in the colleges is designed to produce qualified mineral processing professionals. This includes courses in mathematics and natural science, fundamental engineering and basic and specialization courses. Recently, the ?Excellent Engineer Program? was launched to strengthen students? practical capabilities. This is a 3+1 teaching and training model; 3 years of theoretical course study plus 1 accumulated year of various practical studies, either inside or outside the college. As for graduate employment, mining-related major graduates have been in a good demand thanks to the intensive investment in mineral sector by Chinese companies. The shortage of experienced metallurgists generates a greater than 90% employment rate for Mineral Processing graduates. However, the biggest problem we are still facing is the gap between the quality of the graduates and the requirements of industry, as a result of occupation attraction, teaching systems, faculty quality, and so forth. Another problem is international orientation. Although nowadays Chinese-foreign cooperation in college education is popular, collaborative mineral related projects are far less common, leaving much room for improvement. Looking ahead to the next 10 years, we still have the right reasons to estimate continued prosperity in the minerals sector as well as mineral processing education in China. A brief analysis and views on this will also be shared in the presentation. Keywords: China, mining engineering curriculum, excellent engineer program

Sep 1, 2012

By P Mugebe, M Yahyaei, M S. Kizil, R Low

This paper seeks to establish an empirical relationship between the impact of mining technological innovation implementation and a company’s market value. The company’s market value is represented by its stock price. In a bid to ascertain the relationship, a stock price prediction model is sought to be established using the firm-specific factors impacted by the implementation of innovative technology. This work is performed under the watch of the prevailing macroeconomic factors. The background anchors in the understanding that the difference between the economic status of a mineral deposit and its uneconomic status lies in the level of mining technological innovation most prevalent at a given time (Hartwick, Olewiler and Preuss, 1986; Wellmer and Scholz, 2017; Wright and Czelusta, 2003). This is derived from productivity improvement, resulting in sustainable profitability due to technological innovation. Unfortunately, there is not an adequately established relationship that links this technological innovation impact to the share price performance of the mineral commodity company.

Sep 1, 2024

By Ali Soofastaei

Mining operations are increasingly data-rich yet decisionconstrained. Fragmented systems, variability in geology and operations, and sustainability obligations create multiobjective trade-offs that classic analytics cannot reconcile at operational tempo. This paper proposes an end-to-end framework that fuses digital transformation practices (governed data platform, semantic layer, feature store, and MLOps) with generative AI (retrieval-augmented generation, tool-use, and agentic workflows) and decision intelligence (simulation/digital twins and multi-objective optimization). We formalize sustainability-aware objectives, define a practical stack and governance controls, and demonstrate how an AI “decision copilot” can surface options, quantify trade-offs, and document rationale. Two figures illustrate a production-grade architecture and a Pareto frontier for cost–emissions trade-offs; two tables operationalize decision-domain mapping and a transformation maturity rubric. The approach is product- and company-agnostic.

Feb 22, 2026

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By O. J. Tassicker

The Electric Power Research Institute (EPRI) initiated a program in 1976 to develop and demonstrate an instrument system for on-line continuous measurement of coal properties. The program has focused on the use of Prompt Neutron Activation Analysis (PNAA) for elemental determinations and microwave absorption for moisture determination. One of the major results of the EPRI program is the development of the CONAC (Continuous On-Line Analysis of Coal) instrument, with Science Applications, Inc. (SAI) as the prime contractor and Kennedy Van Saun Corporation as a subcontractor.

Jan 1, 1983

By Bernard J. Steblay

Two instruments have been constructed that extend microseismic data collection and processing capability for Bureau of Mines research in rock burst, coal bounce and outburst, and roof fall monitoring. The first instrument is a 13-channel tape-triggering system. This system allows better utilization of instrumentation tape recorders by collecting data digitally, turning the tape on only when valid data are present, and increasing the dynamic range of the recorder by using digital data. A digital-to-analog converter is used to provide analog output of the recorded digital data. The instrument records a much larger time slice of transient events than do current commercial devices. The second instrument is a microseismic energy measurement device. This device uses recent developments In integrated circuits to overcome the dynamic range and accuracy limitations of previous instruments. The analog signal is converted to a digital one, and then high-speed multiplication techniques are used to square the amplitude value in real time and integrate it.

Jan 1, 1983

By R. L. Grayson, L. L. Probert

"A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams. IntroductionThis is the last in a series of papers detailing the results of SEM/EDX-based analyses of respirable coal mine dust particles collected from field sampling. Previous papers have detailed preliminary results and the statistical validity of the methodology (Grayson, Andre, and Simonyi, 1990; Grayson, 1991). This paper presents the final results of the analysis of respirable dusts from five coal seams with a range of coal rank:• Lykens Valley seam (anthracite), eastern Pennsylvania• Brookville (A) seam (mid-vol bituminous), central Pennsylvania• Pittsburgh seam (high-vol B bituminous), western Pennsylvania• No. 6 seam (high-vol C bituminous), Illinois• Wadge seam (sub-bituminous A), ColoradoSEM/EDX-based techniques were applied to try to clarify the role of quartz as an etiologic agent in coal workers' pneumoconiosis (CWP). It was hypothesized that previous studies were hampered by the restrictions of bulk analysis techniques and that particle-level analyses were needed to answer a number of questions concerning the role of quartz in CWP and its progression.Since 1985, a large number of the respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gero, 1986). Our reasearch shows that conventional bulk analysis techniques may not give a true indication of the biologically available, or active, quartz in mine dusts. Analytical evidence indicates that respirable dust samples may contain many quartz particles that are occluded, or coated, resulting in a bulk analysis for ""free silica"" that may not be indicative of the biologically available quartz surface."

Dec 1, 1996

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By M. Scherzinger, M. Dr. Mazurkiewicz

Additional progress in comminution can be achieved if the compressive crushing principle commonly used at present is changed to one where particles are fragmented by the tensile growth of preexisting internal flaws or cracks, under internal waterjet pressure. This idea was studied in a number of tests and generated results and conclusions are the subject of this paper. It covers tests with different jets imposed on rock samples during compressive load as well as without any loading.

Jan 1, 1992

This paper describes the new iron and steelmaking process recently commissioned at NZ Steel. Ironsand mined and concentrated at Waikato North head is slurry pumped 18 km to the company's Glenbrook works. Ironmaking includes the direct reduction process pioneered at Glenbrook in the 1970s and a new continuous electric melter. The molten, high carbon pig iron produced is then fed to a vanadium recovery unit and on to the KOBM oxygen steelmaking vessel. Steel is cast into billets or slabs. The new plant, which is the first stage of a fully integrated works at Glenbrook, raises New Zealand Steel's production capacity from 150 000 t/y to 750 000 t/y.

Jan 1, 1986

By L. S. Bbosa

Single particle impact breakage experiments provide essential data to aid in understanding of rock fracture in comminution. Such experiments, conducted using devices such as the drop weight tester, split Hopkinson bars and more recently the rotary breakage tester, have been successfully used to characterize ore breakage properties in relation to measured fracture energies. The work presented in this paper highlights the techniques behind the calculation of impact breakage properties from each of these three devices. The breakage parameters that can be calculated from experimental data from each of these are to be described. Drop weight tests are used to calculate A and b hardness parameters using the standard JK breakage model. Split Hopkinson pressure bars are used to establish the ultimate compressive stress of particles through single impact breakage tests and the fraction of impact energy utilized to cause particle fracture. Low energy breakage tests using the rotary breakage tester are shown to be used in calculating particle breakage probability. Methods to calculate parameters related to particle breakage probabilities such as E0 and Ecrit are also discussed.

Jan 1, 2014

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By Michael Murphy, Gamal Rashed, Brent Slaker

Many underground stone mines in the United States operate on multiple mining levels. The effects of interburden thickness, pillar offset between mining levels at various depths of cover, and in situ stress conditions are poorly understood. Pillar offset is the degree to which pillars are not columnized or stacked. In this study, calibrated numerical models are used to examine limestone pillar stability in these conditions. Also, the critical interburden thickness required to minimize the interaction between mining levels is explored. The model results show that there is interaction between numerous factors that control the stability of stone pillars in multiple-level conditions. The highest degree of local pillar instability occurs when pillar overlap ranges between 10 and 70 percent. The highest degree of stability occurs when pillars are stacked.

Jan 1, 2023