Search Documents

By B. Tulu, D. Gearhart

A comprehensive monitoring program was conducted to measure the rock mass displacements, support response, and stress changes at a longwall tailgate entry in West Virginia. Monitoring was initiated a few days after development of the gateroad entries and continued during passage of the longwall panels on both sides of the entry. Monitoring included overcore stress measurements of the initial stress within the rock mass, changes in cable bolt loading, standing support pressure, roof deformation, rib deformation, stress changes in the coal pillar, and changes in the full three-dimensional stress tensor within the rock mass at six locations around the monitoring site. During the passage of the first longwall, stress measurements in the rock and coal detected minor changes in loading, while minor changes were detected in roof deformation. As a result of the relatively favorable stress and geological conditions, the support systems did not experience severe loading or rock deformation until the second panel approached within 30–50 ft of the instrumented locations. After reaching the peak loading at about two to three inches of roof sag, the cable bolts started to unload, and the load was transferred to the standing supports. The standing support system was able to maintain an adequate opening inby the shields to provide ventilation to the first crosscut inby the face, as designed. The results were used to calibrate modeled cable bolt response to field data and to validate numerical modeling procedures that have been developed to evaluate entry support systems. It is concluded that the support system was more than adequate to control the roof of the tailgate up to the longwall face location. The monitoring results have provided valuable data for the development and validation of support design strategies for longwall tailgate entries.

Jan 1, 2017

By L. von Ketelhodt

During the period October 2003 to June 2004, a containerized optical sorting pilot plant was operated at Kloof Gold Mine on a waste rock dump. In this paper, we describe the test work and its results leading to the decision to operate this pilot plant. This paper presents the operational data and financial figures achieved during this project, in particular, for the month of June 2004 when the plant was run at full capacity on three shifts, 24 hour operation. These results are also extrapolated and presented to show the profitability of such an operation at today?s gold price levels and cost structure.

Jan 1, 2009

By Jr. Hill

Laboratory metallurgical treatments of three high-iron bauxite ores from Arkansas were conducted to determine the relative effectiveness of experimental methods for recovering alumina and a commercially acceptable iron concentrate. The standard for evaluating recoveries from experimental processes was the Al2O3 recovery from Bayer digests of the crude ores; recoveries from digestion of the three ores were 74.1, 87.4, and 88.7 percent. Flotation, magnetic separation, or various combinations of digestion, calcination, and reduction-sintering, leaching, and magnetic separation of leach residues failed to produce Al2O3 recoveries as high as the standard. A high-iron-bearing fraction, containing between 68 and 78 percent of the total iron, was produced in a three-phase treatment involving a caustic, lime reduction-sinter of the crude ore, water extraction of Al2O3 from the sinter, and magnetic separation of the leach residue.

Jan 1, 1967

By Chester A. Rowland

INTRODUCTION Comminution is generally a feed preparation step for subsequent processing stages; exceptions being when a final product such as aggregates, specification sand, Portland Cement, and similar products is produced. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding -- primary and secondary), natural or manufactured non-metallic media (pebble milling) or manufactured metallic media -- steel rods, steel or iron balls. This chapter will discuss general mill design and the specific design and application of the following types of tumbling grinding mills. [Overflow Rod Mills Figure 1 Peripheral Discharge Rod Mills Figures 2 and 3 Compartment Mills Rod and Ball Figure 6 Ball Figure 6a Pebble Mill Figure 6b Overflow Ball Mills Figure 8 Diaphragm (Grate Discharge) Ball Mills Figure 9] I. GENERAL MILL DESIGN A. Liners The interior surface of grinding mills exposed to grinding media and/or the material being ground are protected from wear and corrosion by rubber, metallic, a combination of rubber and metallic, or non-metallic wear resistant materials. B. Drives Economics at the time of plant design and mill purchase determine the drive to be used. The simplest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinion-shaft by either an air clutch or flexible coupling.

Jan 1, 1982

Studying the ore textures in a discrete orebody is a novel approach to estimating liberation potential of the ore minerals present. As part of a PhD thesis, this project aims at classifying and quantifying the textures of the Hilton North orebodies, and at estimating their liberation characteristics.

Jan 1, 1993

By David L. Giles

The alkalic igneous province of Montana consists of centers of laccolithic and stock-like intrusive complexes with associated sills, dikes, and breccia pipes (e.g., Judith, Highwood, Little Belt Mts.); isolated plug-like mafic bodies (e.g., Smokey and Eagle Buttes); and clusters of kimberlitic diatremes and ultrabasic dike swarms (Missouri River Breaks). The province extends in a belt throughout central Montana from the North Absaroka Range in the south to the Sweetgrass Hills on the Canadian border. Intrusive activity ranged in age from Late Cretaceous to late Miocene, peaking at about 50 m.y, ago. Diverse types of significant epithermal gold mineralization occur at many of the laccolithic centers. This mineralization took place in large part during the waning stages of, or following, igneous activity. Large remnant travertine blankets in the region attest to comparatively recent hydrothermal activity. The quartz-pyrite-gold mineralization ranges from igneous- hosted stockworks or fracture sets (Zortman-Landusky and Neihart districts) and breccia pipes (North Moccasin Mts.) to replacement zones in flanking and upwarped Madison Group limestone (Gilt Edge and Kendall districts). The latter are mostly localized by intraformational solution breccias in the upper Madison, notably near porphyry contacts. Gold mineralization in the province was accompanied by varying amounts of silver, base metals, sulfosalts, and tellurides, with quartz, fluorite, carbonate, and barite and gangue. Gold occurs as auriferous pyrite, sylvanite, or in native form. Since the 1880's, primary gold production from numerous scattered deposits in the Judith, Moccasin, and Little Rocky Mountains, along with byproduct gold from the Neihart silver district (Little Belt Mountain), has totalled around 2 million oz. The major deposits were in the 1-2 million ton range at an average gold tenor of 0.3-0.6 oz per ton. Most of the ore was mixed oxide or carbonaceous sulfide ore and was treated either by amalgamation or by roasting-cyanidation. Current activity includes heap-leach operations on bulk- tonnage low-grade (approximately 0.03 oz per ton) ores at Zortman-Landusky, and several small-scale, experimental leach or mining operations on carbonaceous replacement ores, as in the Kendall district and Spotted Horse mine. Current exploration efforts for gold are focused not only in the old established districts, but also in and around other alkalic centers, which have been unproductive to date, such as the Crazy Mountains, Sweetgrass Hills, and Bearpaw Mountains. Target concepts in these efforts are porphyry-hosted stockwork or disseminated gold ores and Carlin-type replacement lodes in the flanking Madison or other favorable carbonate units.

Jan 1, 2013

By Ingvar Janelid

13.7-1. General. Iron ore mining in western Europe is mostly carried out underground and only a minor part is mined by open pit methods. Actual open pits of importance in this connection are, among others, Svappavaara in Sweden, Mo i Rana and Sydvaranger in Norway, Corby Mines, Colsterworth, and Scunthorpe in Great Britain, and in western Africa, Nimba and Bong Range in Liberia, and Kedia d’Idjil in Mauritania. The open pit mines of western Africa are of great interest in this connection as they are designed according to European practice and have accepted the same techniques, methods, equipment, etc. as the European mines. In the surface mining of limestone, granite, shale, etc., the technical conditions generally are similar with those in the iron ore mines. Some information will therefore be submitted from typical quarries. The geological conditions at the various iron ore mines and limestone and other quarries vary extensively. In Scandinavia the iron ores occur exclusively in Precambrian rocks. The ore is hard, mostly magnetite or hematite, folded and steep dipping, and hence accessible to surface mining only in the shallow sections. In the mines referred to, open pit mining will last for another 10 to 30 years, whereupon mining has to be continued by underground methods. In France the Minette iron ore has previously been mined in open pits but, because of increased overburden, mining underground with room and pillar methods now dominates. The iron ores are Jurassic, flatlying strata of oolitic type, containing chamosite, siderite, and brown hematite. The British iron ores are mostly of the same origin and appearance as the French deposits, but despite heavy overburden they are preferably mined from the surface. In western Africa, the iron ores are of the same type as in Brazil, i.e., itabirites with high-grade portions resulting from silica-leaching and weathering. The ore contains mostly brown and blue hematite and magnetite. Nimba and Kedia d’Idjil are very similar regarding ore quality and geology. Bong Range is a deposit of low-grade ore which has to be concentrated.

Jan 1, 1968

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By F. T. Cawood

The new mineral royalty regime for South Africa was signed into law in November 2008, with its main objective being to compensate the State for the depletion of public minerals through a royalty charge payable from 1 March 2010. The aims of this paper are to establish the potential impact of mining royalties on State revenues, industry affordability, and explore whether the dual formula system is likely to encourage miners to become refiners. It also measures the royalty dispensation against economists? tax standards in an attempt to make a judgement on the ?equity? of the new system. This paper argues that most stakeholders should be comfortable with most of the requirements of the Act for most of the time. However, the new regime is unlikely to motivate miners to become refiners, as the benefit of the reduced rate on refined minerals appears to be insufficient to justify the additional costs to refine the mineral resource to the prescribed states of beneficiation.

Jan 1, 2011

By L. H. Lindstad

The paper reviews the tapping process and the major wear mechanisms on the tap-hole, including wear from tapping tools. Measured temperatures in different tap-holes are related to choice of binder and material for repair pastes. The strength and disadvantage of carbon and silicon carbide materials are compared. Normal daily and weekly maintenance of tapholes is described, together with the major repairs that are done during longer furnace shutdowns. The objective is to show that the type of repair and repair material needs to be adapted to each individual furnace.

Jan 1, 2014

By Zay Jeffries

Tungsten has the highest melting point of all the known metals, namely 3350 C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely brittle and fragile at room temperature, and when possessing a fibrous structure it may be ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given. Manufacture of Wrought and Ductile Tungsten Up to about 10 years ago, it had not been possible to work tungsten mechanically. About the year 1908, Dr. William D. Coolidge, of the General Electrie Go., produced ductile tungsten from what was then supposed to be an inherently brittle metal and which, in fact, was inherently brittle in its normal state, that is, when composed of equiaxed grains. Since that time many products, chief among which are the filaments for electric incandescent lamps, have been made from wrought and ductile tungsten. Tungsten is produced chiefly from the minerals wolframite and scheelite.1-8 The ores may be reduced in many ways. For example, the ore may be fused with alkali carbonates and the fusion dissolved in water; sodium tungstate is formed, which is soluble in water. This

Jan 1, 1919

By David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and-sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved salts in water; (3) pseudo liquids obtained by suspending solids, such as sand or magnetite, in water, and, (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended sand or magnetite pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous; vertical and horizontal currents of the separating medium occur as either part of the process or unavoidedly produced by the introduction of feed and withdrawal of products, 'so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary is get the recoveries and grade of product desired. Sizes usually cleaned are plus ¼ in. or plus 1/8 -in. in the United States and plus 1/16-in. in Great Britain. Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about 1/8-in. is made difficult by viscosity effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media processes is progressing rapidly and it is likely that equipment, media, and procedures will be developed to clean sizes down to 0.5 mm. efficiently and at low cost.

Jan 1, 1950

By Mansoor Barati, Shaghayegh Esfahani

"The slag from extraction of ferrous and non-ferrous metals is a potential heat source which if treated properly can contribute to recovery of a significant amount of energy. The waste heat of slag may be used to generate steam, synthetic fuel gas, or electricity. Although several technologies have been investigated for this purpose, very little has been achieved in terms implementing the technology in industry. In this article, the development and application of various granulation techniques are reviewed and the methods to recover energy from granulated slag are discussed.IntroductionEvery year, more than 422 million tons of slag is being produced around the world as a by-product of the metal manufacturing at temperatures of up to 1300-1600°C [1, 2]. Currently slags are either disposed of or treated by processes such as granulation. Through the granulation process, most slags can be converted into a material which may be fully used as a cement feedstock. Conventional cement production is an energy intensive process with large emissions of CO2; therefore, the replacement can both be energy saving and environmentally friendly. However, for this purpose, the slag should have what is known as a “glassy” content (i.e. it should be amorphous) which requires rapid cooling rates that are not easily achieved due to the very low thermal conductivity. The main challenge in all these processes is to granulate the slag at a high cooling rate while the heat is also being recovered."

Jan 1, 2012

By J. M. Kuchta

The chemical and thermal criteria used for predicting the spontaneous combustion hazard are briefly reviewed and data are presented to characterize the gas desorptions and self-heating tendencies of 29 U.S. coals. Closed vessel desorption experiments showed that CO, CO2, and CH4 are the main gases evolved and that the CO, CO/?O2 index, and 02 absorption rate increase with decreasing rank and increasing oxygen content of the coal. In this Bureau of Mines report, the effects of temperature, moisture, and other variables are discussed together with the application of the data to the complex conditions encountered in a mining environment. An important finding is that the presence of CO alone in a mine is not necessarily an indication of a self-heating reaction of the coal. Based upon experiments conducted in an adiabatic-type calorimeter, the self-heating temperatures of lignite and subbituminous coals can be as low as 30° C, whereas the bituminous coals require a temperature of about 60° C or more. The self-heating hazard is greatest when the coals are dried and exposed to a high humidity condition, apparently as a result of the "heat-of-wetting." Generally, the hazard is greatest with the western coals of the United States.

Jan 1, 1980

By Robert N. McIndoo, M. G. Woodle

10.5-1. Introduction. In the not-too-distant past, maintenance and the facilities for maintenance were considered a necessary evil to be given only secondary consideration in the development and planning of a surface mine operation. With the increasing sophistication of mining equipment and machinery, this concept has been replaced; and today's mine managers recognize that planning for adequate maintenance facilities is as important to a successful operation as a sound mining plan. This chapter will present the basic maintenance facilities and the fundamental considerations necessary to meet the varied requirements of surface mining. 10.5-2. Determination of Shop Facilities. The size, shape, and extent of maintenance facilities are contingent on the general mining plan, the location relative to outside facilities, and to the available capital. The type of construction employed is dependent on climatic conditions and preference. HAULAGE SYSTEMS. The type of haulage equipment used will dictate the kind of shops needed. Truck haulage requires entirely different facilities than rail haulage. Some mines will employ both systems, and can include hoists, skips, or conveyor belts in combination with locomotives or trucks. The requirements of each type will be discussed. MAINTENANCE ORGANIZATION. The pre-planning decision as to centralized maintenance vs. area maintenance, or a combination of both, will greatly affect the maintenance facilities required. A single pit with relatively short travel from shops to pit will probably have a centralized maintenance system. Where more than one mine is involved, or where there are diversified sections or functions in a mine (mine equipment, mill, conveyor, or

Jan 1, 1968

By Henrique de Siqueira Queiroz

A indústria mineral brasileira é uma das maiores produtoras de minério de ferro do mundo e as reservas do país estão cada vez com teores mais baixos. Por isso hoje são necessários estudos para viabilizar a explotação de jazidas de baixos teores. Utilizando-se de minérios mais pobres, faz-se necessário uma maior cominuição para beneficiamento do minério. Com uma menor granulometria do material, o processo de flotação passa a ter importante papel no beneficiamento por ser mais tolerável aos finos. O objetivo deste trabalho foi testar diferentes coletores catiônicos, especificamente aminas, utilizados na etapa de flotação reversa de um minério de ferro da região do Vale do Rio Pardo. As amostras utilizadas nos testes são provenientes da remoagem que, pelo circuito de beneficiamento, alimenta a flotação de finos. Foram testados como coletores as aminas EDA, EDA3 e EDA 3C da Clariant. A amina que obteve melhor desempenho foi a Flotigam EDA 3C que obteve concentrado final com 67,4% Fe e 1,76% de SiO2, e recuperação metalúrgica de ferro de 92,14%.

Aug 7, 2018

By Dion Pastars

Kestrel Coal has undertaken a surface-to-seam consolidation program of faulted ground prior to longwall retreat in the 304 panel. Micro fine cement is used to improve the rock mass quality and therefore reduce the risk to personnel and equipment whilst increasing previously assumed sterilised reserves. The program is based on information attained from previously successful grouting campaigns in the Queensland coal area and follows the decision making process to ensure there is sufficient spatial permeation of cement across the faulted area. This data is used to assess the residual risk to the business in terms of health, safety and production

Jan 1, 2007

By Ross Seedsman

Discussion on the design of roof support in tailgates has often been conducted without a clear statement of the stress and failure conditions acting. There is general agreement that in the tailgate the vertical stresses above the chain pillar increase. Within the stress 'bulb' associated with this vertical stress increase there will be an increase in horizontal stress. This does not mean that the horizontal stresses acting across the roof line increase. In retreat longwalling, the proximity of the tailgate to the adjacent goof results in a substantial reduction in the horizontal stress field acting in the immediate roof. Furthermore, at the face/tailgate corner the onset of significant compression of the chain pillar. if it is designed to yield, will result in a further reduction in the horizontal stresses in the immediate roof. It is suggested that this latter mechanism can cause the horizontal stresses in the immediate roof to go to zero. Whatever, the horizontal stress acting across the roof in the face/tailgate corner will be significantly lower than in the face/maingate corner. The implication of the model is that support design in tailgates should be based on the assumption of zero horizontal (in fact tensile) stresses. How the roof behaves in a tensile stress environment is a function of joint spacing and orientation compared to excavation width and direction. It is speculated that the empirical relationship between support density and roof rating results from the relationship between joint spacing and bedding spacing. The onset of stress reductions has major implications to the design of cable and bolt anchorages in the tailgate environment.

Jan 1, 2001

By M. Riddell

This paper describes the incipient heatings that occurred below ground in the High Main and Main seams at the mine between the years 1963 and 1966. The possible causes, effects and activities associated with such heatings are discussed in an attempt to establish the precautions necessary to minimize such occurrences. The assessment of as many "norms" as possible is made to enable the earliest detection and level of activity to be determined.

May 23, 1905

By C. R. Stephan, N. B. Greninger, J. R. Lipscomb

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate the strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. The full-scale seals were constructed in the USBM's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 20 psig or greater. bjected to pressure pulses of 20 psig or greater. In experiments prior to this study, seven seal designs using solid-concrete blocks were tested. Only the standard-type seal passed the explosion and air-leakage criteria. Tests also were performed on four seals constructed with low-density foam blocks. All four of these seal designs withstood the pressure pulse. In more recent studies, nine cementitious foam seal designs of varying thicknesses and densities were investigated. Six of the nine designs successfully survived the explosion overpressures. Six wood- block convergence seals also have been tested. The typical 3-ft-thick, wood-block seal design currently used in many coal mines did not maintain its integrity, in the absence of convergence forces, following the explosion test. Five modified wood-block seals successfully withstood the 20-psig pressure pulse. Based on these tests, three alternative seal construction materials, cementitious foam, low-density foam block, and wood, have been approved by MSHA for use in underground coal mines.

Jan 1, 1993