Search Documents

By V. Yahorava

Efficient recovery of precious metals from process solutions is essential for improving process economics. Traditionally, precious metals are relatively effectively recovered from waste streams via precipitation or cementation. However, these approaches have a number of drawbacks, including poor water balance, creation of environmentally unfriendly waste streams, and losses of precious metals. Ion exchange technology is an alternative for the recovery of precious metals from waste or low-grade streams. This technology allows the recovery of the precious metals to extremely low levels (micrograms per litre) with relatively high upgrade ratios from the solution onto the resin without major water balance concerns, while the impact on the environment could be minimized or avoided. Research was conducted on the recovery of platinum group metals and gold from different low-grade and waste streams from one of the precious metals refineries in South Africa by means of ion exchange. Various functionalities and matrices (granular and fibrous) of ion exchange materials were evaluated. The results from these studies indicated that in some cases ion exchange could be very effective for the recovery of precious metals, and that the PGM concentration could be reduced to < 1 mg/L. The upgrading ratios of the various PGMs onto the specific fibres were relatively high for the specific streams evaluated, which might in some cases justify incineration of the loaded material instead of stripping and recycling the adsorbent. The cost of direct incineration for one of the waste streams tested would be less than 1% of the value of the PGMs recovered. However, the adsorbent has to be carefully selected and the process design optimized for each specific stream.

Jan 1, 2014

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

By Tina Maniatis

Applied Biosciences has developed a biological technology for removal of arsenic, nitrate, selenium, and other metals from mining and industrial waste waters.The ABMet® technology was implemented at a closed gold mine site in Canada for removing arsenic from tailings pond water. The system included six bioreactors that began treating water in the spring of 2004. Design criteria incorporated a maximum flow of 567 L/min (150 gallons per minute) and water temperatures ranging from 10°C to 15°C. Influent arsenic concentrations range from 0.5 mg/L to 1.5 mg/L. The ABMet® technology consistently removes arsenic to below detection limits (0.02 mg/L). Data from the full scale system will be presented, as well as regulatory requirements and site specific challenges. Keywords: Arsenic, Sulfate Reduction, Metal Sulfide Precipitate, Biological Water Treatment

Jan 1, 2005

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By M. R. Haibach, M. L. Shema, J. M. Silvis

"Since 2005, longwall coal mine operators in Pennsylvania (US) have been required to collect extensive hydrologic and biological data to document pre- and post-mining conditions of aquatic resources (streams and wetlands) overlying the subsidence control plan areas. Continued operation of the longwall mine is dependent upon empirical data demonstrating that the undermined aquatic resources have either been maintained or restored to an accepted range of pre-mining conditions. This study used quantitative hydrologic methods and comparative biological metrics to examine response of aquatic resources to longwall subsidence at the Bailey Mine located in Greene County, Pennsylvania. This study analyzed data from over 25 miles of streams and over 8 acres of wetlands that traverse the 4,779-acre study area. Hydrologic analysis of flow intermittency suggested that there are variable degrees of change to headwater streams immediately following mining; however, the majority of the effects are reversible through streamflow mitigation measures. Furthermore, the post-mining discharge from streams can be restored to within the range of pre-mining conditions the majority of the time. Biological assessments showed that greater than 95% of assessed stream length has maintained its ability to support benthic macroinvertebrate communities following mining and intervention (i.e., mitigation). Comparative metrics of the benthic macroinvertebrate communities showed that the biological community in 48 of the 50 sample sites is being maintained or restored across both high- and low-gradient streams. The effectiveness of intervention was further substantiated by the similarity in recovery times between streams having no intervention (median = 2.1 years, 95th percentile = 4.9 years) and streams with intervention, when recovery times were measured from the date of the intervention (median = 1.7 years, 95th percentile = 4.7 years). Changes to individual wetlands were observed between the pre- and post-mining assessments, but cumulatively a net gain of 7% in wetland acreage was realized. Hydrologic assessments were used to infer whether there was a potential that streams had been affected by mining; however, the ultimate test of stream recovery is based on biological metrics that establish the relative quality of the biological communities following mining. Overall, the hydrologic balance is being protected and the aquatic life use of streams is being maintained within the Bailey Mine’s subsidence control plan areas."

Jan 1, 2017

By Paul M. Tyler

The value of mica depends chiefly upon the size of the flat sheets into which it can be split and also upon whether it is clear or stained. Muscovite (white mica) and philogopite (amber mica) are the micas of commerce. Biotite (black mica) and other varieties are virtually unsalable. Vermiculite, an altered mica having the extraordinary property of expanding greatly when heated, preferably should not be classed commercially as mica. Mica is marketed as (1) cut or uncut block, (2) sheet, (3) splittings, and (4) wet or dry ground mica. In the United States, mica that will not yield flat films over about 1-1/2 inches square, or that is ruled, rumpled, or flawed in any way, can be sold only as scrap, its sole use being for making ground mica. Only sizes that will yield rectangles 1-1/2 by 2 inches or larger can be classed as sheet quality; slightly smaller sizes may be classed as punch, and under certain circumstances still smaller sizes, down to about 1 inch square, may be used for splittings, which are mostly a thousandth of an inch thick or even thinner. Splittings, however, are produced in large quantities only in British India, where labor costs very little. Even there the work is done mostly by children, who not only work cheaper but have a delicacy of touch that enables them to do the splitting faster and better. No mechanical process yet devised will permit ordinary splittings to be made economically in the United States.

Jan 1, 1938

By Å Sandström

Loussavaara-KiirunavaaraAB?s (LKAB) iron ore mine, Kiirunavaara, is of magnetite type and associated with apatite, a calcium phosphate mineral. Rare earth elements (REE) have been found in connection with the apatite but also in other minerals. An apatite concentrate was produced by flotation, in order to investigate the possibilities to extract REE from the apatite by hydrometallurgical means. The content of rare earth elements calculated as oxides (REO) was 0.44% in the concentrate. Initially, leaching was done with large excess of sulfuric acid, hydrochloric acid, and nitric acid to study the REE solubility with different acids. In sulfuric acid, the leaching recoveries of the different REE varied between 35% and 69%. The reasons for the relative low recoveries, were that the rare earth elements precipitated together with huge amounts of gypsum, that was formed during leaching. However, both hydrochloric- and nitric acid gave almost complete extraction of the REE into solution. Analysis of the small leaching residue obtained, revealed, that mainly the light REE remained in the residue indicating that a small part of the light REE were present in the concentrate, in some acid, insoluble mineral other than apatite. With the aim to separate the REE from the phosphoric acid, the solutions from hydrochloric- and nitric acid leaching were neutralized to a pH of approximately 2 with ammonia. During neutralization, REE were precipitated as phosphates with good recoveries and a concentrate of 10.5% REO suitable for further upgrading was obtained, while the remaining solution can be used for fertilizer production. In further solvent extraction studies, it was shown, that after re-dissolution the REE could be effectively extracted by Cyanex 923, thus allowing for purification from calcium and phosphate ions. The REE were finally stripped from the organic phase and a REE nitrate solution was produced. Keywords: apatite, rare earth elements, REE, leaching, solvent extraction, cyanex 923

Sep 1, 2012

By T. Dlokweni, M. Bester, C. Koegelenberg, I. Basson

Certain degrees of safety, economic, and financial risk are implicit in any mining operation. At Thabazimbi Mine, slope stability was one of the major sources of risk, largely due to data uncertainties. Consequently, a risk-based approach in slope design was followed. On 6 June 2015, a slope failure occurred in Thabazimbi Mine’s Kumba pit, involving approximately 65 million tonnes of rock failing into the pit and the valley below. Although the failed mass moved rapidly and resulted in a run-out distance of approximately 900 m, controls had been put in place to successfully evacuate all personnel. Risk assessment during the onset of failure supported the decision to not compromise the safety of personnel in any way, leading to unavoidable equipment loss. This contribution presents the failure as a case study in the context of a risk-based approach to slope design as well as the importance of implementing geotechnical controls to effectively manage slope instability risk. Furthermore, a comprehensive back-analysis was performed, on a fully constrained 3D model, utilising 3DEC software, to gain insights into the failure mechanism. In conclusion, lessons from the Thabazimbi slope failure are valuable as they demonstrate the importance of following a risk-based approach in slope design to effectively manage safety and financial risk in open pit mines.

Sep 1, 2025

By J Seccatore, G Sadao, M Cardu, G De Tomi, L Finoti, F Galvão, J Romero Huerta, A Rezende, J Bettencourt

In the mining industry, rock blasting can be considered as the first phase of comminution. The downstream phases of comminution are mechanical, and consist in consecutive stages of crushing and milling for grain size reduction. The total energy of mechanical comminution depends on grain size and on the resistance of the material to grindability. Usually, the first is quantified by the grain size distribution or one of its KPIs (such as the diameters X50 or X80), while the latter by the working index (WI), representing the amount of energy necessary to reduce the size of grains of a determined amount of material to the desired equivalent diameter (usually expressed in kilowatt hours per tonne – kWh/t). It is widely recognised that it is possible to manage the output of a blast in terms of grain size distribution varying specific charge (powder factor – PF) and charge distribution; specific algorithms such as the KUZ-RAM or the SWEBREC have been created to predict such output. It has also been demonstrated how higher PFs weaken the blasted material by creating micro-fractures that reduce its WI. This paper focuses on a related aspect: the influence of charge distribution on the specific comminution energy in crushing and milling. Small-scale blasts have been performed on 14 marble blocks with different PFs and charge distribution. For every PF, charges have been designed to simulate concentrated and distributed geometries. Concentrated charges simulate opencast blasts with large-diameter holes, with large burdens and spacings. Distributed charges simulate bench blasts with small-diameter holes and reduced burden and spacing. Three control blocks have been fragmented by mechanical means for comparison. For every sample the grain size distribution and the WI in ball mill has been determined. Results show the correlations between charge distributions and the specific energy of mechanical comminution in milling. Finally, the opportunity of adjusting charge diameters and distributions in opencast blasts to improve the output of the comminution circuits is discussed.CITATION:Seccatore, J, Romero Huerta, J, Sadao, G, Cardu, M, Galv&#227;o, F, Finoti, L, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The influence of charge distribution on the grindability of the blasted material, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 749–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Xiao-hui Fan, Li-shun Yuan, Xu-ling Chen, Wei Lv, Min Gan, Yi Wang

"As the amount of ferrous scrap increases every year, it becomes more and more urgent to deal with this iron-bearing resource properly. This paper puts forward a method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing), and these cold-bonded pellets can be used as coolant in a converter. The influence on the pellets qualities by using different kinds of chloride as rust agents is studied, and results show that the strength of cold-bonded pellets increases significantly by using a combination of the three kinds of chloride -NaCl,MgClz,FeCh, their best dosages are 1.2%, 0.2%, 0.1% respectively. Other iron-bearing materials also have an effect upon the pellets strength, by adding 5% iron powder and maintaining for 48h, the compressive strength of the clumps surpass 2500N/A, dropping strength surpass 4 times/ A, and 10% iron slag or 20% steel slag can replace 5% iron powder while obtaining the comparative quality. The influence of different ratios of three ferrous scrap (converter mud, iron scale and dust) is further studied, and results show that when the ratio is 30% : 30% : 40%, the pellet strength reaches the maximum. After maintaining for 24~48h, the clumps can meet the mechanical as well as the physical-chemical requirements as BOF steelmaking refrigerant.IntroductionGreat amounts of converter mud, dust and iron scale are produced in steel production process. These materials are of great values, and their accumulation not only leads to environmental pollution, but also wastes the precious resources, which restricts the sustainable development of the steel industry [1,2] The main approach at present to dealing with the ferrous scrap is to add them into sintering. But in this way, the utilization factor of sintering and the quality of sinter decline while the energy consumption increases [3].Therefore, more advanced and efficient technology is needed to make the best of these iron resources. Cold consolidation of ferrous scrap is a simple process that has many advantages such as less investment, quicker effect, lower energy and lower cost [4-5] But the conventional maintaining period is too long, usually up to four-six weeks, and the pellet strength is low. Therefore, the key points of the cold-bonded pelletizing are to develop a new adhesive [4,5] to shorten the natural maintenance cycle and to improve the strength of the pellets. A method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing) is brought forward, and these cold-bonded pellets can be used as coolant in converter. After maintaining for 48h, these cold-bonded pellets can satisfy the mechanical requirements to replace the converter coolant [6]."

Jan 1, 2013

"In this work a blasting seismograph was tested on a vibration shaker controlled by a single-point laser Doppler vibrometer (LDV). A total of 43 tests were made to measure the transfer properties(transmissibility and phase shift) of the basic elements of the full monitoring chain and investigate theperformance of the full system. The main elements of the seismograph are described by second ordertransfer functions with typical parameters calibrated through nonlinear fit of the measured responses. The resulting transfer function is used to compare the behavior of the tested seismograph with fourtheoretical seismographs representative of those used in blasting. Fifteen theoretical inputs are runthrough the transfer function of each seismograph to assess their steady-response. The error (expressed as gain) in the peak velocity has been assessed. It varies from -1.5 to 2.3 dB (equivalent to atransmissibility of 0.84 to 1.3, respectively) depending on the seismograph and frequencies of the input.The largest errors occurred for input signals with frequencies in the low (<32 Hz) or high ranges (>125Hz), where the mechanical, electronics and digital parts of the seismograph modify the signals. Seismographs with the nominal transfer function described by DIN 45669:1:2010 are ranked with the smallest errors. Monitoring devices with transmissibility around one in a narrow bandwidth, in line with ISEE suggested criteria for amplitude response, involve large phase shifts at low and high frequencies, resulting in a worst performance."

Jan 1, 2017

By R Redden

"The Didipio Gold-Copper project in the Philippines has been a well-defined reasonably high gold grade porphyry for almost two decades. OceanaGold are now bringing the project into production in late 2012 and have recently reoptimised the project with the goal of combining the inherent high grades with higher through-put than previously proposed that will see strong initial metal production. The project was discovered and well defined by 1995, but has seen some obstacles to development, namely sovereign risk, capital cost and project funding. The project strengths over this time that have kept the flames alive are: strong grades large orebody with low stripping ratios a simple beneficiation process and a clean high-grade concentrate strong support from the Philippines government.The initial study in 1998 used Gold and Copper price assumptions of $325/oz and $0.95&nbsp;lb respectively. Today reserves are based on $950 and $2.85. So, being a porphyry with a large reducing grade halo, the deposit now lends itself to extraction on a much larger scale than before, without any significant capital expenditure as a larger open pit now dominates the project.Didipio is a game changer for OceanaGold, so it has been important to learn from history and to capitalise on a strong initial metal production profile. The project sits in a reasonably remote mountainous area of Luzon which sees annual typhoons and numerous short duration high intensity rainfall events and two rivers flowing through the project area, so it has not been without some innovative technical solutions.CITATION:Redden, R, 2012. Didipio - Learning the lessons, adapting and getting ready for production, in Proceedings Project Evaluation 2012, pp 67-76 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 24, 2012

By F. B. Plummer

PROGRESS during 1940 in oil-production technology has been confined largely to a steady advancement in practices inaugurated in previous years, rather than the introduction of any new startling process or technique. The usual changes, improvements and additions in production equipment have been introduced. An increased attention to, and interest in, research has been noteworthy, resulting in improved efficiency in operation of oil wells. control, utilization of reservoir energies and reduction of production costs.

Jan 1, 1941

By J. Armanet

THREE MINING colleges are maintained in France; the École Nationale Supérieure des Mines, of Paris; École Nationale Supérieure des Mines, of Saint Etienne; and the École Supérieure de la Metallurgie et des Mines at Nancy. Besides graduates of these schools, a few graduates of the École Centrale des Arts et MIanufactures and of the École Polytechnique are employed as ]nine managers or engineers; however, most of the latter have taken a graduate course at one of the mining schools.

Jan 1, 1939

By Robert Snow, Shibo Zheng, Wenyi Song, Xiaoqing Ma, Patrick Zhang

Numerous phosphate mineral depressants have been reported in the literature for use during anionic flotation of dolomite from carbonate fluorapatite in slightly acid circuits. In one part of this research, laboratory flotation experiments were conducted to compare the effectiveness of phosphate depressants to process ground, deslimed high-MgO Florida phosphate pebbles. Ten potential phosphate depressants were evaluated during laboratory anionic flotation of dolomite from phosphate in a slightly acid circuit using a sulfonated oleic acid soap plus oil as the dolomite collector. Eight of the depressants have been used by various investigators with foreign and domestic carbonate-phosphate ores. Four of the depressants were found to be reasonably effective during the current flotation study, namely: sodium tripolyphosphate (STPP), sodium hexametaphosphate (SHMP), tetrasodium pyrophosphate (TSPP) and diphosphonic acid (DPA). Without depressants, the sulfonate collector required to produce cell underflow phosphate products containing <0.80% MgO and MgO/ P2O5 ratio <.033 was 1.13 kg/ton of flotation feed at a flotation pH range = 5.5-6.0. Using this collector level with 0.91 - 1.36 kg/ton of feed of STPP, SHMP or TSPP yielded phosphate products analyzing 0.73-0.92% MgO and MgO/ P2O5 ratios = .027-.034 at 90.0-96.8% P2O5 recovery. Similar grade phosphate products were obtained using DPA as the phosphate depressant at 84.1-87.5% P2O5 recovery. When no depressant was used, a similar grade phosphate product was obtained at only 65.9% P2O5 recovery. Another part of the research aimed at reducing MgO content in the final concentrate from Florida phosphate plants by conducting dolomite flotation on the final concentrate. Numerous phosphate depressants were tested for this purpose, including acidic, neutral and alkaline reagents. The most effective phosphate depressant was found to be phosphoric acid, giving both high grade and recovery.

Jan 1, 2014

By Marcos Daniel Gouveia Filho

A análise das séries temporais no domínio da frequência é tradicionalmente feita estudando-se o espectro de potência obtido através da transformada de Fourier. O teorema de Fourier diz que se pode expressar uma função periódica como uma soma de uma constante e de uma série determos de senos e co-senos, onde as frequências associadas com essas funções são múltiplos inteiros (harmônicos) da frequência fundamental. A análise de ondaletas é capaz de revelar aspectos de dados que faltam em outras técnicas de análise de sinal, aspectos como tendências, pontos de degradação, descontinuidades em derivados mais altas, e de auto-similaridade. Além disso, porque proporciona uma visão diferente de dados do que aqueles apresentados por técnicas tradicionais, a análise de ondaletas muitas vezes pode comprimir ou retirar o ruído de um sinal sem degradação apreciável. Nesse contexto, os sinais de emissão acústica provenientes da deformação por tração uniaxial em amostras de polietileno foram analisados e caracterizados, resultando em clara distinção entre os sinais provenientes dos regimes de deformação elástica e plástica.

Aug 16, 2017

By Farouk T. Awadalla

The presence of humic species in spent Bayer liquor causes many processing problems in the production of aluminum hydroxide. Ozonation of spent Bayer liquor was found to be an effective process to destroy the colored humic species. The kinetics of the decolorization in spent Bayer liquor was found to be slower than in the alkaline humic acid solution containing no alumina. However, the reaction kinetics ware enhanced by heating the solution during ozonation above room temperature. Copper ions which are used as catalyst to enhance the ozonation reaction were found to be ineffective due to the presence of large quantities of aluminum hydroxide in the liquor. Ozonation was a more favorable process than membrane separation as it achieved about 92% separation of color and produced lower amounts of organic material. The treated spent Bayer liquor can be recycled to the upstream process without causing any difficulties and the purity of aluminum hydroxide product would also be improved. A comparison of preliminary cost data indicated that ozonation compares very favorably with membrane separation in this application. Key words: ozonation, Bayer liquor, aluminum hydroxide, humic species, copper ions, membrane separation, purity and economic.

Jan 1, 1994

By JAMES QATLEY

THE atmosphere, which plays such an important part in the manufacture of iron and steel, is the most variable element involved in its several processes; and particularly is this true of the blast-furnace process, which consumes air in large quantities. At no time since the blast-furnace became an important and widely used apparatus-even when it was operated in the most crude manner-have the variations in composition of the raw materials used been as frequent and as great as the variations in humility of the atmosphere. Important, improvements have been made in the blast furnace and its accessories, such as the hot-blast stoves, the increase in size and change in the shape of the furnace, more efficient blowing engines, the increased protection given to the bosh walls, and the careful preparation of&apos; the raw material, all of which have exerted a pronounced influence on the furnace-operations from a metallurgical standpoint. But during the past eight years little advance has been made in this direction; the fuel-consumption has not diminished, nor has there been any material increase in production. Within that period, however, there has been witnessed the greatest development in appliances for the economical handling of material. So complete has been the work in this direction, that, except in isolated cases, in this country at least., a further extension does not hold out much promise of a satisfactory return on the investment required. It seemed that, with the exception of the gas-engine, we had about reached the limit, for like a strong wall, the atmosphere, with its humility as variable to-clay as when first blown into a primitive blast-furnace, appeared to stand as a Barrier to

Jan 1, 1905

By R Razanatsimba, A Galli

A mining company has entered into contractual commitments to supply certain quantities of its product to clients in each time period. Failure to fulfil its obligations would damage its reputation as a reliable supplier. The planned production would normally be sufficient unless major problems such as highwall failures, roof falls, natural disaster, or strikes that interrupt production or delays in obtaining environmental permits, occur. To overcome these difficulties, the company may be able to obtain more of the commodity: from its strategic stockpile (if there is sufficient there); by buying it on the spot market; or for some commodities such as gold and uranium, by leasing it. Two sources of uncertainty, the spot price of the commodity and the occurrence of serious incidents that interrupt production, are considered. For simplicity it is assumed that the commodity price follows a geometric Brownian motion, that productions incidents have a binomial distribution, that they are independent from one time period to another and that they do not affect prices. A branching tree structure is used to model the joint evolution of prices and production incidents. The aim of this research project was to evaluate the companyÆs options for fulfilling its contractual commitments. When evaluating these options, multi-stage stochastic programming with recourse was used to solve this problem because in addition to providing the dollar value of the project, it gives decision-makers the æroadmapÆ to reach the optimal value. That is, how much material should be bought/sold on the spot market, how much to add to/subtract from the stockpile, how much to lease and in the worst case what the shortfall would be, for each time period as a function of the current spot price and breakdown status. A case-study over a five-year period is used to illustrate the proposed procedure. In this study the production would be sufficient to cover the companyÆs contractual commitments unless production incidents occur. Focus is on evaluating the impact of the quantity initially in the stockpile on the value of the project when the commodity market is tight, that is, when only small quantities can be bought on the spot market or by leasing.

Sep 26, 2011

By A. René Silva

The separation of Fe(III) from simulated Ni(II) solutions using different ion exchange resins was studied. The resins tested included cation exchangers with sulfonic and carboxylic groups and chelating resins with iminodiacetic, aminophosphonic, and mixed sulfonic and phosphonic groups. The dosage of resins was varied from 0.1 to 0.5 g/mL to study the impact of resin type and dosage on iron separation from simulated nickel leach solution containing 25 g/L Ni(II) and 25 g/L Fe(III) at pH 1.5. Also, the effects of different metal ion concentrations, Fe (III):Ni(II) ratios in solution, pH, and adsorption times were investigated. Experimental results demonstrate that all the chelating resins selected favored the adsorption of Fe(III) over Ni(II) with high Fe(III) loading. Soft cation exchange resins also favored the adsorption of Fe(III) over Ni(II), but no significant Fe(III) loading was observed. In contrast, strong cation exchange resins did not show adsorption preferences. The most efficient separation was observed using resin with aminophosphonic groups at resin dosage of 0.2 g/mL, having a Fe(III) adsorption over 94% and Ni(II) adsorption below 5%.