Search Documents

By I. R. Kramer

The delay time for single crystals of iron, zinc, and pre-strained aluminum was measured under conditions of high-speed deformation. The delay time of aluminum was found to be affected by the orientation of the crystal. Under the dynamic conditions employed, tile calculated "activated volume" term appears to be very small for the three metals studied. IN a previous paper,1 it was shown that under dynamic testing conditions at 78° K, there was a delayed yield in single crystals of aluminum and copper which had been cold-worked prior to testing. The experimental results also indicated that the delay-time effect was not due to the interaction of dislocations with impurity atoms or vacancies, but rather to a dislocation-dislocation interaction since aluminum which has not been prestrained shows no delay-time phenomenon. In this paper, some data are reported on the effects of orientation on the delay time of aluminum single crystals; the delay time of zinc single crystals saturated with nitrogen and the delay time of iron single crystals also were measured. EXPERIMENTAL PROCEDURE Aluminum (99.997 pct) and zinc (99.999 pct) crystals, 1/2 in. in diam and 8 in. long were grown by the Bridgman technique. The iron single crystal was supplied by Dr. R. Maddin. The zinc crystals containing nitrogen were prepared by melting high-purity zinc in a graphite crucible and the nitrogen was introduced by additions of ammonium chloride. The liquid zinc was then drawn up into glass tubes of 1/2 in. diam and allowed to solidify. The rods were cooled to room temperature before the transfer to the mold for conversion into single crystals. The orientation of all specimens was determined by the Laue' back-reflection technique, Fig. 2 and Table I. To prepare for the delay-time measurements, the crystals were cut with a fine jewelers saw and the ends carefully machined. The specimens then were electrolytic ally polished to remove the cold-worked metal, mounted in a special fixture and hand-lapped. As a final step, the crystals were annealed in evacuated tubes. Specimens of aluminum crystals, Nos. 24 and 26, were compressed 0.5 and 2 pct, respectively, in the direction of the later impact. The zinc specimens were aged at 50°C for 15 min, In the case of iron, only two specimens could be obtained. To obtain sufficient data, it was necessary to resort to a reaging treatment. After each delay-time test, the specimens were aged at 65° C for 100 min. This treatment, according to Clark,2 is sufficient to restore the original delay time. It is believed that although the specimens were plastically deformed approximately 10-4 pct, after each test the delay-time values are reliable. The delay-time measurements were made in an apparatus similar to that described previously.' Single crystals approximately 1 in. long and having a diameter of 1/2 in. were placed in a pendulum which consisted of a bar 1/2 in. in diam and 8 ft long, designed with a crystal holder to accommodate the specimen at low temperatures. The crystal was held at a position 2 ft from the front part of the pendulum. This portion of the apparatus was supported on a fine molybdenum wire. A projectile bar of the same diameter and length comprised the other portion of the apparatus. This bar was supported on

Jan 1, 1962

By S. R. Dunbas, D. C. Jillson, E. A. Anderson

THE present work was undertaken to furnish information, lacking in the literature, on the deformation mechanisms active in pure titanium at room temperature. Since it was started, Rosi, Dube, and Alexander' have indicated that slip can occur in coarse-grained (2 to 6 mm diameter) titanium on the {1010} and {1011} planes and twinning can take place on the {1072}, (1122) and (1151) planes. Liu and Steinberg,' working with titanium flakes produced by fused salt electrolysis, found evidence of twinning on the {1032$, {1121), {1122}, (1123}, and (1154) planes. The crystals used in the present work were substantially longer (up to nearly 2 in. in length) and possibly purer. Production of Large Crystals It was the purpose of this part of the work to provide single crystal or large grain specimens for use in the deformation studies rather than to study the mechanism of crystal growth. Accordingly, all further exploratory studies on methods were abandoned when it was found that cold-rolled bars sealed in vacuo in individual Vycor tubes and given three or more cycles of 4 hr at 1200°C and three to five days at 850°C, gave large grains. Eighteen specimens about 0.2 in. square x 2 in. long yielded 33 useful grains, ranging from Va in. to nearly 2 in. in length, with an agreeably wide range of orientations, Fig. l. The 0.25 in. thick strip from which the starting specimens were cut had been reduced 67 pct on 18 in. diameter rolls from a scalped, hot-forged (959" to 1000°C), arc-melted, iodide titanium ingot. Thc bar was at room temperature, but the rolls were at 200°C. Reductions of about 0.03 in. per pass were used. The bar was cut into four segments, each of which was rolled in a somewhat different manner. No effect on the growth of large grains was noted. The composition of the titanium, determined on turnings from the ingot scalping operations, is given in Table I. The Rockwell A hardness of the ingot was 26. The standard starting specimens, about 1/4x1/4x2 in., were milled on all four sides, hand polished on 280 and 400 mesh emery papers, etched for 3 min in a 50 HF-50 glycerine solution, rinsed, and dried in alcohol and ether just before sealing them in Vycor tubes. The average specimen weight was 7.5 g, and the tube volume was 6.5 cc. A vacuum of less than 1 micron pressure was applied. The specimen tubes were placed in an evacuated Inconel muffle to minimize the danger of collapse of the glass tubes at temperature. In practice the specimens were first heated to 1200 °C for 4 hr and then transferred fairly quickly to an 850°C furnace where they were held for three to five days. This cycle was repeated at least three times before the specimens were cooled, removed from the tubes, lightly polished and etched on one surface for examinstion. Those in which large grains had not developed were resealed in Vycor and returned to the cycling. Satisfactory specimens (about one out of every four cycled) were polished with emery paper on all four side;, then metallographically polished using ctchinz between wheels to remove distorted metal and, finally, given a very light etch to reveal the grain boundaries. This was necessary because the surface was roughened by the sublimation of titanium under high temperature vacuum conditions. Specimens were identified by TiXl numbers using supplementary letters to designate specific grains.

Jan 1, 1954

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp's law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster's results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,' who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp's law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,' but is probably due to some other cause, such as antifer-

Jan 1, 1960

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By I Wilkomirsky

The neutralization of S02 from copper smelter gases to produce calcium sulphate (anhydrite) is considered an attractive alternative to sulphuric acid production. To develop the required technology for the process, a three-stages fluidized bed reactor prototype was designed and operated using both high and low grade limestone and gases with 2, 8 and 12 vol -% S02. The results obtained shows that at 800°C and up to 8 vol-% S02 in the gases, the capture of S02 reaches near 99% with limestone conversion to anhydrite of 45 to 48%. A larger pilot plant is presently being built at the Codelco El Teniente-Caletones Smelter to demostrate the technology and to evaluate the economics of the process. Cu2007

Jan 1, 2007

By E. Oshilna

The Mitsubishi process has many advantages pertaining to economical and environmental matters. These advantages have led to the installations of the Mitsubishi process in constructing new smelters: The Mitsubishi process utilizes highly oxygen enriched blast air and uses a special lime slag in the C?furnace. These characteristics change the . distribution of Impurities from other processes which use P.S. converters, Recently an Increased amount of secondary materials which contain impurities Is being treated at Naoshima Smelter. In order to cope with an Increment of the Impurities load and maintain the cathode quality, many Improvements have been Implemented. This paper discusses the impurities behavior In the Mitsubishi process and describes the measures taken to treat an Increased ?amount of secondary materials:

Jan 1, 1998

By Xueyuan Nie, Xuezhi Zhang, Henry Hu, Shen Xinwei, Jimi Tjong, Li Fang

With the demand for weight reduction in vehicles and airplanes, researchers have shown great interested in casting wrought aluminum alloy 7075 because of its potential advantages such as high strength-to-density ratio and stress-reduction capabilities. It is therefore essential to conduct a fundamental investigation on solidification behavior and grain microstructure of alloy 7075. In this study, a commercially-available wrought aluminum alloy 7075 was used to study the solidification behavior of alloy 7075. A thermal analysis was performed based on the cooling curve and its corresponding first and second derivative curves. The nucleation of the primary a-Al phase and eutectic phases were analyzed. The comparison between the microstructures of the wrought and cast 7075 alloys shows that coarse microstructure and porosity are present in the cast alloy. The techniques for grain refinement in casting, such as the addition of the nucleating particles and applied pressure, should be employed to reduce the dendrite arm spacing and the porosity.

Jan 1, 2015

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

By Staff

In 2012, the estimated value of mineral production increased in the United States for the third consecutive year. Production and prices increased for most industrial mineral commodities mined in the United States. While production for most metals remained relatively unchanged, with the notable exception of gold, the prices for most metals declined. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates (Table 1). After continued decline following the 2008-2009 recession, the construction industry began to show signs of improvement late in 2011 and throughout 2012, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction.

May 1, 2013

By Jaeheon Lee, Junmo Ahn, Doyun Shin

"Many alternative leaching systems including bacterial leaching have been introduced to avoid passivation on the surface of chalcopyrite and to increase the leaching efficiency of copper from chalcopyrite. Recently, glycine, one of the simplest amino acids, has been emerging as an efficient and environmental-friendly lixiviant to recover copper. In the present study, an alkaline glycine–peroxide lixiviant system was used to leach copper from chalcopyrite concentrate and the leaching mechanisms were also investigated by a suite of kinetic studies under different conditions. The chalcopyrite concentrate contains 28.8% copper with 30.8% sulfide sulfur. The effect of concentration of glycine and hydrogen peroxide of the leaching solution was investigated. Glycine concentration was varied from 0.5 to 1.0 M and the hydrogen peroxide concentration was changed between 3 to 5%. Leaching time and pulp density were also varied. Hydrogen peroxide is an oxidant of the system and the leaching efficiency with periodic additions of the peroxide was also studied. A mineralogical study was performed using XRD and SEM. To investigate the surface of the residue materials, XPS was used to see if any passivating layer was formed during the leaching. Detailed results from mineralogical, chemical, and metallurgical studies will be presented and discussed.INTRODUCTION The greatest global resource of copper is low-grade chalcopyrite and heap bioleaching may be the only economic option for its processing. However, formation of a passivating layer on the surface of chalcopyrite slows down the oxidation reaction and reduces the efficiency of the process."

Jan 1, 2017

Newmont Australia Limited has for some 15 years mined a number of large open cuts associated with the Telfer Gold Dome deposits. The principal ore body exploited has been the East Flank of the Main Dome where a very high grade gold reef deposit of mixed metal sulphides, grades in excess of 20gA Au, has been mined in conjunction with dissemi- nated mineralisation contained in the overburden material. The main ore body has been under review for some years as an under- ground mine, however due to the ore body widths of less than 1 metre and a dip generally less than 35 degrees and a very weak host rocks earlier studies all resulted in a continuation of open pit mining activities. In early 1988 it was recognised that open cast mining would not be able to mine all of this valuable resource and a feasibility study was commenced to come up with a practical and economic approach to underground mining.

Jan 1, 1991

By Auã Kiahla, Tomi Kouvonen, Vinicius Miranda

Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper

Feb 1, 2020

By B. M. Burchfiel

CALIFORNIA possesses such an abundance of ceramic materials other than clays, that she is quite independent of other states and foreign countries so far as these materials are concerned. Certain users import some feldspar, silica, and allied minerals, but they do so from choice and not necessity. Production is largely for home consumption, so the total volume of ceramic materials produced is comparatively small. Many small deposits of the materials here under discussion are worked by individuals, and their output sold to individual grinding companies or users. The data given here shall be confined to the larger deposits and developments because they give a truer picture of typical deposits, operations, and materials.

Jan 1, 1936

By R. Holmwood, M. Faris, P. Holloway, M. Collins

Sulphuric acid addition is a major driver of the economics in the processing of nickel laterite ores by high pressure acid leaching (HPAL). Understanding the optimal acid addition rate is essential for the success of any HPAL operation, and this is especially true at Ambatovy, where the composition of the feed tends to vary significantly on a day-to-day basis. Most studies on the effect of acid on nickel extraction in HPAL have used laboratory testwork as their basis. Although these studies are invaluable in assessing the economics of a new project, they are limited by the range of ore composition that can be tested and the differences between the operation of the laboratory equipment and the commercial plant. To enable optimization of the acid addition at Ambatovy, operating data from the HPAL operation were obtained using OSISoft’s PI system and the data from several periods were examined to develop relationships between acid addition and nickel extraction. The initial relationships from 2014 focused on the acid required to achieve a target nickel extraction of 95%, with aluminum and magnesium in ore and feed slurry solids content as the major variables. As Ambatovy ramped up through 2015 and 2016, the calculated acid requirement was further refined to address the effects of HPAL temperature and retention time, and the oxidizing/reducing characteristics of the ore, and to generate acid requirement relationships as a function of ranges of nickel extraction. These relationships supported raising the target nickel extraction to 96% and enabled the development of an economic model between acid addition and nickel extraction.

Jan 1, 2017

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By LINDSAY BOTTOMER, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

A master composite (Master Comp) sample was prepared from three pegmatite zones from the Zoro Dyke D1 for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample that was crushed to approximately P80 = 600 μm. The sample consists of spodumene (10.5 percent), quartz (29.3 percent), plagioclase (29.0 percent), K-feldspars (21.3 percent), micas (5.1 percent), tourmaline (2.9 percent) and Fe-Mn-phosphates (0.1 percent). Liberation of spodumene (88 percent) and gangue minerals, including quartz (89 percent), feldspars (94 percent) and micas (83 percent), is very good at this P80 . The average lithium (Li) concentration is 3.7 percent in spodumene, 2,196 ppm in micas, 1,001 ppm in tourmaline and 115 ppm in K-feldspars. Spodumene accounts for 96 percent of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other Li carriers. The HLS was conducted on a subsample that was crushed to smaller than 6.4 mm, with the smaller than 600 µm fraction removed from this test. The HLS results indicate it is possible to produce a high-grade lithium concentrate, with close to 6 percent Li2O, after the rejection of iron silicates with magnetic separation.

By J. Priede, G. Gerbeth

"Two different instability mechanisms of electromagnetically levitated bodies are analyzed. The first is due to the virtual coupling between the electric current passing through the magnetic system and the variation of position of the body. This mechanism can result in unstable mass center oscillations of a levitated solid body. Another type of instabilities may occur because of the coupling between the motion and the electric currents induced in the body. This effect can cause a spontaneous rotation of the body setting in as the frequency of the alternating magnetic field exceeds certain critical threshold depending on the configuration of the field. This instability can be suppressed by an axial steady magnetic field of strength comparable to that of the levitating field. 1 IntroductionAn alternating magnetic field interacting with eddy currents induced in a conducting body causes repulsion between the body and the coil generating the field. Besides, the eddy currents provide a contactless heating of the body. In such a way metallic samples can be levitated and melted without a contacting crucible. This technique allows to avoid contamination of the melt with container material and so to achieve a considerable super-cooling of the melt before it solidifies. Nowadays electromagnetic levitation is widely used in material research for measuring of the thermophysical properties of molten metals (2) .It has been observed since early fifties when the first experiments on the electromagnetic levitation were done that under certain circumstances solid levitated samples start to rotate or oscillate [l]. Surface oscillations can appear in addition when the sample is melted. Such phenomena are undesirable because they often result in failure of the levitation. Recently we showed that rotational as well as oscillatory instabilities can have electrodynamic origin related to additional eddy currents induced by motion of the body in an alternating magnetic field [3] , [4].In the first part of the present paper we analyze another possible cause of oscillatory instability due to the coupling between the electric current passing trough the magnetic system with variation of the position of the levitated body. The second part of the paper deals with the origin and suppression of rotational instability in a uniform alternating magnetic field."

Jan 1, 1999

Sampling errors result from heterogeneities within the lot under study. Within a rock mass in situ heterogeneity results in the geological nugget effect, which accounts for most of the natural variability. In broken rock, constitution and distribution heterogeneities are important. A major result of the constitution heterogeneity is the Fundamental Sampling Error (FSE) which is the smallest residual error that can be achieved. It cannot be eliminated, but can be minimised and refl ects the fact that the broken rock sampling process is never completely free of error. Together with other sampling errors, FSE contributes to the total nugget effect. The FSE for a sampling protocol can be evaluated using the so-called Gy equation. Its practical applications to low-grade gold ores have often been unsuccessful due to problems linking the FSE and minimum sampling mass and the defi nition of key parameters such as the liberation diameter. Well-designed sample protocols minimise the total sampling error and hence the nugget effect. Reduction of the nugget effect is a key requirement for all sampling programs whether related to exploration and resource evaluation, metallurgical test sampling, grade control or metallurgical plant sampling. This contribution reviews the relationship between heterogeneity, FSE and nugget effect in gold deposits; and emphasises the need for FSE management throughout the mine value chain.

Aug 1, 2010

By R Sterk, B Reid

The Konongo Gold Project is located on the western margin of the 125 Moz Ashanti Gold Belt in Ghana, West Africa. It is situated 60 km along strike of the world-class mineral system at Obuasi and is interpreted to lie on the same controlling regional shear system.The project is operated by Signature Metals, a subsidiary of the Liongold Corporation, and is managed and funded by the Liongold Corporation.Historic underground operations at Konongo produced 1.6 Moz Au at a head grade of 11.8 g/t Au, from eight operations spread along 16 km of the shear system. Mining focused almost exclusively on free-milling gold in quartz, ignoring the gold-bearing sulfide mineralisation associated with the quartz veins. Underground mining ceased in 1986.In 2013, Signature Metals re-focused the program at Konongo to assess the viability of mining the sulfide ore sustainably. This led to the first campaign review of the historic underground data and resource potential since mine closure. The Obenemase mine was the first of the eight operations to be assessed as part of this campaign.Large amounts of legacy data have survived for Obenemase and several historic resource estimations have been completed based on these data. The data typically consisted of hand-drawn sections and plans, and ledgers of commonly incomplete drilling and sampling data. Some drill core have been lost over time, but a large amount of quarter-core and half-core as well as pulps and rejects are still available. Previous resource estimates had a low confidence value because all the available assay and geological data were integrated effectively with the estimates, resulting in a lack of understanding of both grade and geological continuity.This project built a new geological model for Obenemase that greatly enhances the understanding of the controls on mineralisation using a thorough approach of re-surveying, re-cataloguing and re-logging. This model led to an increased degree of confidence and a subsequent upgrade of resource classification, and created several previously unrecognised strong exploration targets. The resulting resource estimates increased the value of the project by 100 per cent.This paper emphasises and highlights the importance of a well-understood geological model on the confidence of a resource estimate and how this may directly impact on the project’s ‘bottom line’.CITATION:Sterk, R and Reid, B, 2014. The Konongo Gold Project, Ghana – an example of how geology makes all the difference to a resource estimate, in Proceedings Ninth International Mining Geology Conference 2014 , pp 467–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014