Search Documents

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

By M. Brozek

The constant of flotation velocity is the value characterizing the kinetics of cyclic flotation. In the statistical theory of flotation its value is the function of probabilities of collision, adhesion and tearing off the grain from the air bubble. The grain ? air bubble collision plays a key role since there must be a prior collision before the grain ? air bubble adhesion happens. The probability of such an event to occur is proportional to the relation of the grain diameter to the bubble diameter. When the grain sizes are given, it is possible to control the value of collision probability by means of the size of air bubbles. Consequently, it is significant to find the effect of physical and physicochemical factors upon the diameter of air bubbles in the form of a mathematical dependence. In the pneumo-mechanical flotation machine the air bubbles are generated by the blades of the rotor. The dispergation rate is affected by, among others, the rotor rotational speed, the amount of air transported to the flotation chamber an time and the liquid surface tension, depending on the type and number of applied flotation reagents. In the proposed paper the authors will present the distribution of air bubble diameters on the grounds of the above factors, according to the laws of thermodynamics. The correctness of the de-rived dependences will be verified empirically.

Jan 1, 2014

In the Bowen Basin of central Queensland, coal production has gone from virtually nothing in 1961 to more than 24 million tons today4ut there's a cloud over this success.

Jan 1, 1977

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900

By B. Orberger

The fine fraction (< 2 mm) of the high grade Mn-ore from the world class Moanda deposit, Francevillan basin, in Gabon, contains up to 30 wt. % of manganese and about 0.4 wt. % phosphorous. A pilot study at laboratory scale integrating mineralogy and geochemistry before and after ultrasonic treatment was conducted on the fine fraction (< 2 mm) of oxidized Mn ore in order to reduce the phosphorous content and enrich this fraction in manganese. The fine fraction was dried, crushed at 2 cm and sieved at 2 mm. The two fractions (< 2 mm and 2 mm ? 2 cm) were investigated by X-ray diffraction and scanning electron microprobe ? electron dispersive spectroscopy analyses. Both fractions contain lithiophorite, cryptomelane and pyrolusite as Mn carrier, and goethite, muscovite, illite and quartz as contaminants. The Mn hydroxide nsutite was only found in the fraction 2mm ? 2 cm.The < 2 mm fraction is significantly richer in goethite, muscovite/illite, and quartz. Phosphorous carriers are mainly goethite (up to 2.8 wt. % P2O5), while the Mn minerals contain up to 0.8 wt. % P2O5. The Mn minerals are partly included in an agglomerate of goethite, muscovite/illite, and quartz. The < 2 mm fraction was treated by ultrasound for 30 s in normal water. Mineralogical and chemical analyses after ultrasound treatment showed that the Mn-minerals were largely liberated from the goethite-muscovite-illite agglomerate. Mass balance calculations show that after ultrasonic treatment the < 2 mm fraction was ? 50 % enriched in Mn and ?50 % impoverished in P.

Sep 1, 2012

By WILLETT G. MILLERS

GENERAL RECEPTION COMMITTEE.-Willett G. Miller, Chairman; F. G. B. Alan, Hon. Frank Cochrane, Eugene Coste, Thomas W. Gibson, Cyril W. Knight, J. C. Murray, 0. N. Scott, Alan Sullivan, J. B. Tyrrell, J. W. Wells, A. B. Willis. COBALT RECEPTION COMMITTEE.-Arthur A. Cole, Chairman; Will. Ask with, R. W. Brigstocke, Robt. Bryce, Fred Coombs, M. I. Culbert, I. R. Drummond, J. W. Evans, A. Ferland, F. N. Flynn, E. L. Fraleck, S. R. Heakes, Joseph Houston, D. L. Jemmett, I. R. Jones, Major Leckie, Capt. Jack Leckie, R. W. Leonard, W. H. Linney, Alexander Longwell, Frank Loring, Murdock McLeod, John Martin, D. B. Rochester, W. E. Running. COBALT RECEPTION COMMITTEE (Ladies).-Mrs. A. A. Cole, Mrs. A. Edwards, Mrs. R. Jennings, Mrs. S. H. Logan, Mrs. A. Longwell, Mrs. H. F. Marsh, Mrs. J. Smith. SUDBURY LOCAL COMMITTEE.-Mayor L. O&apos;Connor, Chairman; S. Fournier, Secretary; A. H. Beath, W. J. Bell, F. B. Bennett, D. M. Brodie, J. S. Buchanan, F. C. Busby, Wm. Chalmers, R. Dorsett, W. A. Evans, John Frawley, J. S. Gill, A. B. Gordon, J. G. Henry, T. N. Kilpatrick, Major Leckie, Chas. McCrea, John McLeod, Wm. McVittie, R. Martin, R. S. Mitchell, J. H. Morin, J. A. Orr, James Purvis (President Board of Trade), C. R. Reid, Major Smith, W. W. Stull, J. F. Templeton, S. E. Wright. The first session, held in the Banquet Hall of the King Edward Hotel, was called to order Tuesday, July 23, 1907, at 2.30 p.m., President John Hays Hammond presiding. Prof. Willett G. Miller, chairman of the General Committee, introduced Alderman J. J. Graham, who, in behalf of the City of Toronto, extended a hearty welcome to the members and guests of the Institute. To this welcome, President Hammond replied in a few well-chosen and hearty remarks. In the hall in which the session was held there was exhibited a fine, full-length, life-size portrait of Dr. Rossiter W. Raymond, in 1871 Vice-President and acting President, in 1872, 1873 and 1874 the elected President, in 1876 and 1877 Vice-President, in 1883, by appointment of the Council, and for the last 24 years by annual election, Secretary, of the Institute. Dr. James Douglas, of New York, N. Y., on behalf of numer-

Sep 1, 1907

By Y. Tanaka, H. Miki, Y. Aoki, H. Okamoto, G. P. W. Suyantar, T. Hirajima

Due to environmental limitations and the scarcity of freshwater, flotation using seawater or desalinated seawater as process water becomes more common for mining operations. On the other hand, seawater has been reported to affect the flotation behavior of sulfide minerals. Few reports are available on influence of pyrite depression, recycled seawater and lime consumption on flotation by using seawater. In this study, the flotation tests were performed using ore sample to investigate the effect of pH with seawater and process water used in plant on the flotation behavior in a laboratory-scale flotation cell and a pilot plant-scale. The results of laboratory scale flotation indicated that copper and molybdenum flotation kinetics decreased with increasing pH. Furthermore, the iron (mainly pyrite) recovery decreased with increasing pH. The pilot plant-scale flotation test showed that water with a higher concentration of magnesium and calcium (plant processes water) consumed a higher amount of lime. Because of low lime consumption and high copper and molybdenum recovery and grade, pH 8 is suitable compared with pH 8.5 for flotation. Keywords: seawater, process water, copper-molybdenum rougher flotation, pH, pilot test

Jan 1, 2020

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By M. Grozdanovic, D. Marjanovic, M. Ilic

We present a framework for solving the problem of functional compatibility between process control equipment in control centres at underground mines and operator capabilities. The equipment incorporates displays of current ventilation, gas, and fire hazard data, status of alarm and early warning systems, a voice communication subsystem, and facilities for recording and printing ofdata and reports. The layout of the existing control panel is compared with a recommended design. The basic principles of ergonomic design and arrangement of the controls and indicators, as well as ease of use, type of operations carried out with these controls, and operators’ viewing angles are discussed. The objective is to improve the usability of control panels, display boards, and graphic screens so as to enhance the functioning of control centres and optimize control of technological processes in coal mines.

Jun 10, 2024

By E. Morrice, R. D. Smith

Thermal expansion and electrical resistance measurements were made on cerium metal from 4° to 300° K. The apparatus developed , including a specimen holder and a cryostat system , are described along with the experimental techniques used in obtaining the measurements . The total linear thermal expansion Data at of 99.83 weight - percent cerium metal between 4 ° K and room temperature was 4.24 percent . The resistivity at 4° K was 7.0 x 10-6 ohm- centimeter . 4° K indicate a fundamental relationship between residual resistivity and purity of cerium metal . The effects of annealing and repeated thermal cycling on resistivity were determined .

Jan 1, 1964

By Victor Maksaev, Marcos Zentilli

"Abstract - The Domeyko Cordillera, the westernmost uplifted crustal block of the composite High Andes of northern Chile (20°S to 28°S) hosts a narrow N-S trending belt of Late Eocene-Oligocene giant porphyry copper deposits, which include Collahuasi, Chuquicamata, El Abra, La Escondida, and El Salvador. These deposits are spatially and genetically associated with the closing igneous activity along this range, prior to a 30 km eastward jump of the magmatic front in response to tectonic plate interaction. The porphyry copper deposits are also spatially associated with a major intraarc strike-slip shear system, the Domeyko Fault System. Although the tectonic uplift of the 3000 m to 5000 m high range has generally been assumed to be mostly Miocene in age, field relationships suggest that the Domeyko Fault System and tectonic uplift were active as early as the Eocene, coinciding with porphyry copper emplacement between 41 Ma and 30 Ma. Apatite fission track (FT) thermochronology provides both age data and a time-temperature history for rocks since they cooled below a temperature of ca. 125°C (equivalent to a depth of 4 km to 5 km under normal geothermal gradients) on their way to the surface during exhumation, or after a heating event. Apatite FT data from the Paleozoic crystalline basement of the Domeyko Cordillera indicate that at least 4 km to 5 km of rocks were eroded during exhumation of this tectonic block between ca. 50 Ma to 30 Ma (Middle Eocene to Early Oligocene), a time that immediately precedes and overlaps with the emplacement of giant porphyry copper deposits. The FT data constrain the age and duration of a period of crustal thickening and extensive erosion known as the Incaic compression, an event recognized in the Andes of Chile and Peru. Assuming that cooling was due to denudation alone, modelling of the FT data allow estimation of denudation rates between 200 and 100 m/My during this period. In contrast, exposures of pre-porphyry Paleocene intrusives on the western edge of the Domeyko Cordillera reveal apatite FT ages that are concordant with biotite 40Ar-39Ar dates, indicating shallow emplacement, fast cooling and negligible exhumation. The apatite FT ages of the Chuquicamata and El Abra porphyry copper deposits are only marginally younger than their 40Ar-39Ar dates, implying fast cooling/exhumation of shallow mineralizing systems (ca. 2 km to 3 km). Their FT time-temperature history is compatible with extremely low rates of exhumation (ca. 50 m/My) since about 30 Ma (Early Oligocene). This limited extent of erosion, due to exceptional aridity, has greatly contributed to the preservation of rich supergene enriched blankets above some of the porphyry copper deposits.A model is proposed, which is consistent with field relationships, geochemical, and geochronological data. High relative velocities and intermediate-angle oblique convergence between the Nazca and South American plates in the Eocene-Early Oligocene led to intra-arc transpression partitioned into reverse faults of opposing vergence and a right-lateral shear system (the Domeyko Shear System) localized along the magmatic front. Crustal shortening and thickening led to uplift within the Domeyko Fault System and to erosion of at least 4 km to 5 km. Crustal thickening deepened the zone of magma generation, and magmas accumulated in the lower crust, allowing small volumes to rise rapidly to shallow levels along transtensional domains of the regional shear system. A similar model of crustal thickening and shortening before and during porphyry copper emplacement in zones of transtension may also apply to the Miocene-Pliocene giant porphyry copper province of central Chile."

Jan 1, 1999

By H Ishikawa, H Zhou, M Spagnolo, R Halomoan, S Palaniandy

The Karara Mine concentrator commenced operation in November 2012 to produce high-grade magnetite concentrate. The circuit consists of three stages of comminution plus magnetic separation at each stage for early gangue rejection. High-Pressure Grinding Rolls (HPGRs) are used for fine crushing, followed by ball mills and TowerMills in secondary and fine grinding duties respectively. In recent times, the plant throughput rate has had to exceed design by 18% to maintain the targeted concentrate productivity. Meanwhile, the ore hardness has increased by 25% to 15 kWh/t, leading to changes in the circuit operation and design. These changes led to coarser and harder feed to the TowerMill circuit that affects the subsequent separation processes. Nippon Eirich (the TowerMill manufacturer) has partnered with Karara Mining Limited (Karara) to optimise the TowerMill circuit operation to achieve a circuit product with an 80% passing (P80) of 35 &#181;m. Several activities, including a TowerMill circuit audit and performance evaluation, multi-component analysis, modelling and simulation, were carried out as part of the optimisation exercise. The circuit audit results revealed that the TowerMill circuit feed size F80 had increased and ranged from 67–75 &#181;m. The circuit product P80 ranged between 42–55 &#181;m. The average circuit specific energy was 3.4 kWh/t. Moreover, the differences in density between magnetite and gangue minerals had affected the hydrocyclone performance where the efficiency curve exhibits coarse end deflection indicating that low-density coarse material was bypassing to the overflow stream. A multi-component analysis was carried out to further investigate the coarse end deflection of the hydrocyclone efficiency curve. The analysis showed that the magnetite and gangue minerals had different cut sizes of 32 and 64 &#181;m respectively. Furthermore, 33% of the magnetite (below 35 &#181;m) was being recycled back to the mill due to the density effect. Based on these findings, several recommendations for process improvement were identified and implemented including:• converting to a bottom feeding configuration to improve the grinding efficiency in the mill• additional grinding power in the fine grinding duty to compensate for the increase in plant throughput and ore hardness• improved classification efficiency by converting to smaller size hydrocyclones. Simulation studies carried out to evaluate the impact of these implementations had indicated that a P80 close to 35 &#181;m with a steeper size distribution could be achieved by using the bottom feed configuration with additional grinding power. The TowerMill circuit was converted to bottom feed configuration and the performance was evaluated. The operating work index, size specific energy and circulating load were 30% lower than the top feed configuration, indicating that the bottom feed configuration had a higher grinding efficiency. This paper discusses the outcome of the circuit audit, multicomponent analysis, circuit simulations, improvement strategies and quantification of the improvements. CITATION:Palaniandy, S, Spagnolo, M, Halomoan, R, Zhou, H and Ishikawa, H, 2017. Fine grinding circuit process improvement at the Karara mine concentrator, in Proceedings MetPlant 2017, pp 101–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Roberts AW

Bulk materials handling operations depend on efficient storage and gravity flow facilit- ies. ,It is important that proper attention be given to the complete storage bin or stockpile and feeder combination. The paper briefly des- cribes the principles of efficient feeding and discusses the common types of feeders under practice. While ideally unaided gravity flow should be sought, occasions arise where flow promotion is necessary. Various types of flow promotion devices are described and their operational features evaluated.

Jan 1, 1978

By T. X. Hu

Pyrite ore is one of the main raw materials in the production of sulfuric acid. For a long time, the raw material containing the pyrite, which is used to produce sulfuric acid, generally contains S only 32%~45%. A plenty of residue from the sulfuric acid production contains 40%~50% Fe and 1%~2% S. Some of the residue also contains Cu, Pb, Zn and other harmful elements like As, thus it pollutes environment seriously and is solid waste. The research on comprehensive utilization of the residue has been made by many scholars. Through the study, the residue can only be used to pro-duce iron concentrate and the iron oxide red pigment. But because of the complex techniques, the low recovery, the low grade of iron concentrate , high sulfur in iron concentrate, causing second waste residue and the environmental pollution, the residue is mainly used as an accessory material in the production of cement, and is of a low value. Therefore, the iron resource in pyrite has not been used efficiently until now. In the paper, the flotation condition test, the flotation open circuit test and the flotation closed circuit test to produce high-purity pyrite concentrate with the low-grade pyrite ore in oceanic ore deposit have been carried on. Flotation reagent scheme of sulfuric acid used as activator and butyl xanthate as collector is determined. After four times depth cleaning, high-purity pyrite concentrate containing 52.82% S, 44.29% Fe, and only 2.89% impurities has been obtained. The S recovery is 99.13%, and the Fe recovery is 96.00% in the high-purity pyrite concentrate. The oxidizing roasting depth desulfurization experiment of the high-purity pyrite concentrate has been conducted. The results show that the Fe grade in the residue obtained is 68.58%, the content of S is 0.25%, the content of P is 0.0084%, the content of As is 0.0065%. The residue is a kind of high-quality iron-smelting raw material. Based on the above experiments, the industrial experiments on producing high-purity pyrite concentrate with the low-grade pyrite ore, and producing sulfuric acid and iron concentrate with high-purity pyrite concentrate have been done. The results indicate that the high-purity pyrite concentrate with the S grade of 51.24%, the Fe grade of 44.15% has been obtained. The iron concentrate obtained with 65.73% Fe and 0.23% S is a sort of high-quality iron-smelting raw material applied to the production of steel and iron smelting. Through the experimental study, the sulfur and iron resources in the pyrite ore have been recovered and utilized efficiently.

Jan 1, 2014

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in &apos;slimes&apos;. In the early 1970&apos;s, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world&apos;s tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By Tiany Guedes Cota

A indústria cerâmica utiliza as argilas como matéria-prima para fabricação de cerâmica vermelha, branca, de material refratário, entre outros. Possuem um vasto campo de aplicação devido às suas características que, em geral, são decorrentes de sua composição química e do processo de fabricação que lhe originou, tais como: temperatura de queima, proporção dos componentes e granulometria da matéria-prima utilizadas. Comumente vem sendo realizada a substituição de parte da massa argilosa por resíduos industriais, para aproveitamento de materiais, diminuição de custos e impacto ambiental. Nesse presente trabalho, foi realizado um planejamento fatorial em dois níveis das variáveis de adição de pó, temperatura de queima e pressão de compactação nas propriedades de densidade, retração linear de secagem (RLS) e de queima (RLQ). A coloração final também foi um parâmetro analisado. A temperatura parece ser a variável que mais influenciou nos resultados de densidade e RLQ. A pressão de compactação dos corpos de prova não foi uma variável significativa na densidade, RLS e RLQ. Logo, a condição ótima para fabricação dos corpos cerâmicos foi com incorporação de 10% de pó de despoeiramento em substituição ao solo argiloso e temperatura de queima de 1000°C.

Aug 17, 2017

By K Osten, N Scagliotta, G Lane

Oceana Gold (New Zealand) Limited operates the Macraes Gold Mine near Dunedin on the South Island of New Zealand. The orebody is mineralogically complex and comparatively low grade requiring a series of unit processes and resulting in a relatively complex plant. As part of Oceana GoldÆs ongoing Business Improvement program, a concerted effort has been made to focus on operational efficiency. One aspect of this has been the efficient use of energy in the gold recovery process. A benchmarking process has been developed for the Macraes operation that includes comparison with other operating mines and theoretical design. Criteria for determining operational efficiency have been developed. While benchmarking is, in theory, a simple process, this paper looks at putting benchmarking into practice by catering for variability in ore and associate processing methods. The unit processes discussed include the comminution circuit, flotation plant, pressure oxidation plant and gold recovery circuits.

Jan 1, 2004

By F. R. Koeberlin

ABOUT thirty miles south of the port of Coquimbo, Chile, nestling in one of the western outliers of the main Andes range, lies the little mining town of Andacollo, a place whose history and traditions make up one of the most romantic pages in the life story of this southern republic. The beginning of Andacollo is shrouded in the penumbra of the pre-Columbian era, but its first mining activity probably dates from about the years 1440 to 1460. It was in the middle of the fifteenth century that the Inca Tupac-Yupanqui, grandfather of Atahualpa, conquered this part of Chile. His domain extended even as far south as the present site of Santiago, and perhaps farther, but was maintained with increasing difficulty against the fiercely independent and indomitable tribes of Araucanian Indians of the South.

Jan 1, 1938

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By L. Pan

As an air bubble approaches a mineral surface, a thin liquid film (TLF) is formed in between. The excess pressure (p) in the film determines the kinetics of drainage, which is of critical importance in flotation. We have developed a new method of monitoring the kinetics for both stable and unstable wetting films and analyzed the results using the Reynolds lubrication theory. It has been found that initially a TLF is thinned by the Laplace pressure (pcur) due to changes in bubble curvature and subsequently by the disjoining pressure (?) created by the surface forces present in a wetting film. In the present work, we have derived an analytical expression for determining ? from the temporal and spatial profiles of TLFs on mineral surfaces. The results show that ? > 0 in a film formed on a hydrophilic surface and ? < 0 in a film formed on a surface hydrophobized by collector. Thus, the role of collector in flotation is to create a hydrophobic force and hence a negative disjoining present in wetting films. It is also found that smaller bubbles can create higher Laplace pressure, which helps the TLF drain faster.

Sep 1, 2012