Search Documents

By E. H. Hamilton

THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total 100.0 THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total?100.0?20,580

Jan 1, 1924

By R. M. S. Häggblad

The article deals with stabilisation and regeneration of Ce02 and Ce02/Zr02 based Pt water gas shift catalysts, subject to high initial deactivation. The reaction gas species effect on the catalyst deactivation was investigated by H2-TPR. Activity measurements enabled the effect of different promoters, some added to the Ce02 based catalysts and some to the Ce02/Zr02 based Pt catalysts, to be investigated. The catalysts were also characterised by BET and CO-TPR. Deactivated catalysts activity was restored by using various regeneration methods. Of the two selected carriers the Ce02/Zr02 based Pt catalyst showed the highest resilience to deactivation. For the two different carriers, Ce02 and Ce02/Zr02, Wand Re were the best promoters when the catalyst was subject to deactivation. Experiments with Hr TPR indicate a fast initial change in the platinum oxides concentration and composition. The CO-TPR was used to make conclusions about the various regeneration effects of water and oxygen on the catalyst. Finally it is suggested that not one deactivation mechanism is possible and which mechanism that dominates is dependant on the catalyst and the reaction gas composition.

Jan 1, 2005

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By Reda Mikhail, M. Birkan Bayrak

The Washington State Department of Transportation (WSDOT) State Route (SR) 167/70th Avenue East Vicinity Bridge Replacement Design-Build project is located in Fife, Washington. This $40 million project consists of replacing the existing 70th Avenue Bridge over Interstate 5 (I-5) with a single-span bridge of about 220 feet long with approach embankments. The subsurface conditions along the new bridge alignment generally consists of alluvial deposits with high potential of liquefaction overlying glacially overridden deposits. In the early stages of the project, drilled shafts were considered as the deep foundation system; however, after an additional subsurface investigation is completed at the site, driven pipe piles were selected as the deep foundation system. Bridge abutments are supported by 24-inch diameter, 80-foot-long open-end driven steel pipe piles. The pile length was determined to bypass a relatively thick liquefiable zone and to tip the piles above what could be compressible soils. The use of advanced seismic analysis was instrumental in optimizing the pile length. The dynamic testing performed on numerous piles indicated what could be unique soil setup factors compared to those measured in local projects as well as those reported in national design manuals. Detailed discussions of the pile foundations design and construction is presented in this paper.

Sep 8, 2021

By Johann F. Kerl

Autogenous batch grinding tests were performed in laboratory-scale tumbling mills with magnetite, limestone, and sandstone pebbles. The influence of pebble size, feed size, mill speed and loading, and grinding time on the fineness of grinding was investigated. Comparisons were made with the results from ball mill grinding experiments.

Jan 1, 1972

By C. E. Richards, C. N. Reid

The influence of preferred orientation on the incidence of defbrtnation tuinning has been studied. High-purity iron with almost vandonz grain orientation was cotnpared uitll iron of the sa)ne grain size and composilion lza,ing a strong (110) fiber texture. As expected from published work on single crgslfls, /he ))lean stress for the onset of luitzning-, and the l,olu)nt. fraclion of twinned nzaterial obserlled in lension differed fron the 1-a1ue.s it2 co?nPression for tnolerial with a slrong texlure. The llinning stress of "rctndorrl " )zalerial did not 17ary with the sense of the aPPlied unin.via1 stress, but sirprisinglg the incidence of 1c)i)zning- was about three 1i))zes greater ill conzp?&apos;ession Illon in lension. These results (Ire attributed entirely to ovienbation and may be nderslood in ler?ns of the shear slresses acting on the allowed twinning syster)is. J. HE twins most commonly formed in bcc metals may be described as regions of the crystal in which a particular set of (112) planes is homogeneously sheared by 0.707 in the appropriate ( 111) direction. A similar twin-related crystal could be produced by a shear of 1.414 in the reverse (111) direction but twinning by this large displacement has never been reported. Thus, twinning is unidirectional and a shear stress which produces twinning does not do so when its sense is reversed. The sense of a shear Stress is reversed when the loading is changed from tension to compression, or vice versa. Consequently, for a given orientation of a crystal relative to a uniaxial stress, only a fraction of the twelve (112) twinning systems are geometrically capable of operating in tension, and the remaining systems may operate only in compression. Therefore, when twinning is involved, there are expected to be differences in behavior between crystals tested in uniaxial tension and those tested in compression. This has been verified experimentally by Reid et 01.&apos; and Sherwood el al.,&apos; although a critical stress criterion was not encountered. Furthermore, twinning stresses in colmbium," tungten, tantalum,&apos; irn,&apos; i-Fe,\ nd molybdenum7 single crystals have been shown to depend critically on orientation, although again twinning did not occur at a critical value of the macroscopic shear stress. However, when twinning occurs, it generally does so on the most highly stressed systems, 1--4&apos;6&apos;8&apos;9 implying that the stress level does have some relevance to twin formation. In view of the large orientation dependence of twinning in bee single crystals, it might be expected that such an effect would be present in poly crystalline material which possesses a recrystallisation texture. Indeed, riestner" showed that the twinning stress in tension is very orientation-sensitive it1 <&apos;grain-oriented, silicon-iron;" this material possessed a very strong t c m^ii a nnr x_____k . i-_ii__ ri_______j. _x r»i_._:__i preferred orientation obtained by secondary recrystallisation. Reid et a/.&apos; observed a marked difference in the tensile and compressive yield stresses of polycrys-talline columbium which was rationalised in terms of the effect of a preferred orientation on twinning. No other such illformation is known to the authors. Several investigations of twinning in polycrystalline bcc metals have been reported in which the possible existence of a preferred orientation was not even mentioned. It is the purpose of this paper to show that there is a strong effect of texture on twinning in polycrystalline iron, and to poilt out the difficulty in eliminating preferred orientation in recrystallised metals. 1. EXPERIMENTAL METHOD Material and Specimen Preparation. Low-carbon, high-purity iron was obtained from the National Physical Laboratory in the form of $-in. diam rod which had been cold-swaged from a diam of 1 in. The composition of the material is given in Table I. The as-received bar was cold-swaged directly to 0.185 in. diam from which cylindrical tensile and compression specimens were machined. Specimen geometry is illustrated in Fig. 1. The gage length was 0.30 in. long and 0.10 in. diam; it should be noted that, apart from the extra heads which are necessary for tensile loading, the geometry and dimensions of the two types of specimen are identical. The specimens were heat treated either by sequence A or B outlined in Table 11. The essential difference between these two treatments is that in one case the material was repeatedly cycled through the y- to a-phase change in order to produce grains of almost random orientation ("random" iron)

Jan 1, 1969

By David M. Lake

Conversion to trolley assist is a means of minimizing diesel fuel consumption, which in many mining situations offers a rapid payback of capital investment plus the inherent flexibility and maneuverability of truck shovel operation. When diesel electric truck shovel mining operation with trolley assist is compared to alternative mining methods such as conveyor systems, the trolley assist system can be easily justified in terms of return on investment, payback and increased productivity. A review of present technology, performance requirements and past experience in the mining industry has led to the development of a trolley assist system for diesel electric haulage trucks which, is proven in the mining environment, offers significant reduction in fuel consumption and increased productivity.

Jan 1, 1981

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.&apos; In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By Lawrence G. Houk

Lithium is the lightest of all metals, but as it deteriorates rapidly in air it has no structural applications. Alloys of lithium that will float upon water can be made with other light metals, but these ultralight alloys are not useful in aircraft production or elsewhere at present. Alone or alloyed with alkaline earth meals, lithium acts as reining agent on molten metals, and as a minor constituent with other metals it imparts characteristic properties to the allay. Lithium compounds have somewhat wider application in commerce than either the metal or the alloys. They are used in the glass, ceramic, chemical, and air-conditioning industries and less extensively in the optical, pharmaceutical, electrical, and textile industries. The United States is the leading producer anti consumer of lithium ores and compounds and apparently has the largest known ore reserves. The value of lithium ores and primary chemical byproducts produced is relatively small, yet the lithium chemical industry yields products worth hundreds of thousands of dollars each year, owing partly to the high degree of purity demanded by the trade for most finished products and to the low combining weight of lithium. Fortunately, the low-grade ores can now be concentrated economically, and this fact, together with our extensive reserves, assures adequate supplies to meet any reasonable increase in demand. Lithium is listed as essential by both the American and British war agencies, and its military importance may be greatly enhanced.

Jan 1, 1942

Among countries afflicted with insLantaneous outbursts of coal and gas, Australia is noteworthy because of lesser disturbances of the seams and of the occurrence of CO2 in the seam gas from place to place. Research sLarted with the 1954 occurrences at Collinsville and Metropolitan Collieries leading to early publications reviewing the problem, describing occurrences and assessing variations in proneness factors in the two affected coal basins.The basic requirements for proneness include coals of high gas sorptive capacity, high ground stress, use of a mining method which provides higher stress concentrations and limits emission of seam gas, including high rates of advance. With CO2 in the seam gas proneness is greater.The mechanism is complex and not fully understood, but involves the coal, the roof, the floor, the gas, the mine opening, the ventilation, the kind of work and the rate of work. Geological disturbances such as faults and dykes increase proneness and tend to localise occurrences. On-occurrence of outbursts in some mines is difficult to explain.Outbursts are seen as a continuing threat to modem deep Australian mining of high rank coal.The simplest contributory factor to reduce is gassiness - despite the low permeability of outbursting coals - and present practices are showing promise. The greatest challenges for the future are partial degasification to below a known threshold figure and confirmation that this reduction is achieved and identification of anomalous geological structures ahead, the most likely locations for instantaneous outbursts to occur. The advances made to date give promise of a future with reducing experiences of uncontrolled instantaneous outbursts. For the Bulli seam particularly, working to achieve prediction and prevention is most urgent.

Jan 1, 1993

By Zhonglin Ye, Yifeng Shi

"This paper has outlined forms of Au & Ag losses in copper smelting process and methods for increasing Au & Ag recovery, analyzed factors influencing Au & Ag recovery in copper converting process, presented Au & Ag behavior in copper electrorefining process, and reviewed effect of current density/electrolyte circulation rate during electrolysis and surface finish of cathode on Au & Ag losses. Measures and research direction for decreasing Au & Ag losses in electrolysis have also been introduced. Based on Au & Ag behavior in copper electrorefining process and previous studies by others, new approach for increasing Au & Ag recovery in copper smelter has been discussed. And brief comparison has made between continued multiplication method and equilibrium method application in the case of calculation of Au & Ag recovery in copper smelter.IntroductionAs gold and silver are the major by-products from copper smelting process, efficient Au & Ag recovery has become one of the key approaches for copper producers to increase economic efficiency. With similar physicochemical properties, Cu, Au and Ag belong to the first subgroup of elements in the same periodic table. Au and Ag will be enriched into Cu phase firstly when both matte-slag phase and copper-matte phase appear in copper smelting process. However, great changes have taken place in Au & Ag proportions into individual phase due to changes of physicochemical conditions in each smelting process. Metallurgists at home and abroad have carried out a great deal of pilot plant tests and laboratory tests in order to increase Au & Ag the former Soviet Union with regard to Au & Ag losses in copper smelting process in the 1970s and 1980s, and he proposed solutions to increase Au & Ag recovery in copper metallurgical plants. As more than 20 years passed, Jingchun Lu's paper, Discussion on Increasing Au & Ag Recovery in Copper Smelting System, remains as a literature of the most comprehensive study. Based on Jingchun Lu's literature, the authors of this paper discussed new approaches to increase Au & Ag recovery in copper metallurgical plants with combination of many researches done by other researchers for over 20 years."

Jan 1, 2013

On the Art of Metallography (Howe Memorial Lecture), by F. F. Lucas; Beneficiation of Iron Ore. Abstract of paper by C. E. Williams followed by Round Table Discussion; A Statistical Analysis of Blast-furnace Data, by R. 8. McCaffery and R. G. Stephenson; Air Discharge of Circular Tuyeres, by R. S. McCaffery and D. E. Krause; Open-hearth Steel Process as a Problem in Chemical Kinetics. by E. R. Jette; Carbon-oxygen Equilibrium in Liquid Iron, by H. C. Vacher and E. H. Hamilton; A Thermodynamic Study of the Phasial Equilibria in the Bystem Iron-carbon (Abstract), by Yap, Chu-Phay; Influence of Dissolved Carbide on the Equilibria of the System Iron-carbon (Abstract), by Yap, Chu-Phay; Inclusions and Their Effect on Impact Strength of Steel, I and 11, by A. B. Kinzel and W. Crafts: Method for Electrolytic Extraction of MnO, MnS, FeS and Si02, Inclusions from Plain Carbon Steels, by G. R. Fitterer; Permanent Growth of Gray Cast Iron, by W. E. Remmers; Some Notes on Blue Brittleness, by L. R. van Wert; Austenite-pearlite Transformation and the Transition Constituents, by A. Sauveur; Age-hardening of Austenite, by F. R. Hensel; Transformational Characteristics of Iron-manganese Alloys, by H. Scott; Composition Limits of the Alpha-gamma Loop in the Iron-tungsten System, by W. P. Sykes; Magnetic Properties Versus AUotropic Transformations of Iron Alloys, by T. D. Yensen and N. A. Ziegler; Dilatometric Study of Chrome-nickel-iron Alloys, by V. N. Krivobok and M. Gensamer; Low-carbon Steel, by H. B. Pulsifer; Bright Annealing of Steels in Hydrogen, by F. C. KeUey; Development of Continuous Gas Carburieing, by R. J. Cowan. Transactions, Institute of Metals Division, 1931. 500 pages. Index. Papers and discussions presented before the Division at Chicago, Sept. 22-26, 1930 and New York, Feb. 16-19, 1931. X-ray MetallograpIhy: X-ray Determination of Alloy Equilibrium Diagrams (Annual Lecture), by A. F. Westgren; Suppressed Constitutional Changes in Alloys. by G. Sachs; Texture of Metals after Cold Deformation; by F. Wever. Theoretical Metallurgy: Studies upon the Widmanatitten Structure. I.—Introduction. The Aluminum-eilver System and the Copper-silicon System; by R. F. Mehl and C. S. Barrett; Studies upon the Widmanstatten Structure, 11.—The Beta Copper-einc Alloys and the Beta Copper-alumnum Alloys, by R. F. Mehl and 0. T. Mareke; Application of X-rays in the Manufacture of Telephone Apparatus, by M. Baeyerts; Thermal Conductivity of Copper Alloys. 11.—Copper-tin Alloys; 111.—Copper-phosphorus Alloys, by Cyril Stanley Smith; Thermodynamic Study of the Equilibria of the Systems Antimony-bismuth and Antimony-lead, by Yap, Chu-Phay. Ganeral: Cemented Tungsten Carbide; a Study of the Action of the Cementing Material, by L. L. Wyman and F. C. Kelley; Influence of Casting Practice on Physical Properties of Die Castings, by C. Pack; Fabrication of the Platinum Metals, by C. S. Sivil; Effect of Certain Alloying Elements on Structure and Hardness of Aluminum Bronze, by 9. F. Hermann and F. T. Sisco. The WorkinG oF Metals: Metal Working in Power Presses, by E. V. Crane; Forming Properties of Thin Sheets of Some Nonferrous Metals, by W. A. Straw, M. D. Helfrick and C. R. Fischrupp; Die Pressing of Braas and Copper Alloys, by J. R. Freeman. Jr.; Plasticity of Copper-sina Alloys at Elevated Temperatures. by A. Morris: Directional Properties in Cold-rolled and Annealed Copper, by A. Phillips and E. 9. Bunn; Effect of Combinations of Strain and Heat Treatment on Properties of Some Age-hardening Copper Alloys by W. C. Ellis and E. E. Schumacher; Constituents of Aluminum-iron-silicon Alloys, by W, L. Fink and K. R. Van Horn; Equilibrium Relations in Aluminum-antimony Alloys of High Purity, by E. H. Dix, Jr., F. KeUer and L. A. Willey; Equilibrium Relations in Aluminum-magnesium Silicide Alloys of High Purity, by E. H. Dix. Jr., F. Keller and R. W. Graham; Constitution of High-purity Aluminum-titanium Alloys, by W. L. Fink, K. R. Van Horn and P. M. Budge; Experiments on Retarding the Age-hardening of Duralumin, by E. H. Dix. Jr. and F. KeUer; Aluminum-silicon-magnesium Casting Alloys, by R. S. Archer and L. W. Kempf; Modulurr of Elasticity of Aluminum Alloys, by R. L. Templin and D. A. Paul; Quenching of Alclad Sheet in Oil, by H. C. Knerr.

Jan 1, 1931

By T. H. Patching

This paper provides a review of the available information on the origin and mechanisms of the release of gas from coal seams. With the opening up of new mines in Western Canada and the increased mechanization of underground coal mines, the study of gas emissions is of increasing importance in providing safe working places underground.

Jan 1, 1970

A new watersoluble binder for mineral ore pellets has been developed by the sulfonation of bituminous materials. A highly effective binder for iron ore pellet making is obtainable from bituminous materials produced in the hightemperature cracking of crude oils. This paper deals with production process and basic properties of this binder as well as new applications in the field of iron ore pelletizing.

Jan 1, 1974

By Charles W. Goodale, William A. Akers

The treatment of silver-ores of too low a grade to justify either smelting or preliminary roasting, and yet not " free" enough to permit of raw amalgamation, has ever been a serious problem. As bearing upon it, the operations of the Combination Mining and Milling Company of Black Pine, Deer Lodge county, Montana, during the past year may not be without interest. It is not claimed that the process to be described is not susceptible of great improvement, nor is any claim of originality made for it; but its use is, as yet, not very general, and it seems to offer a means of profitably working the large class of partially-decomposed argentiferous ores which, by reason

Jan 1, 1890

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.&apos; The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

By W. F. Netzeband

This paper, which describes mining methods and practices at the Rialto zinc-lead mine American Zinc, Lead & Smelting Co., in northeastern Oklahoma, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States, The Rialto mine is in the SE1/4 SW1/4 sec. 20 and the NW1/4 sec. 29, T. 29 N., R. 23 E., Ottawa County, Okla. (fig. 1). The 200-acre property is southwest of and adjacent to the town of Picher in the central part of the Picher field of the Tri-State zinc-lead mining district (fig. 2). Other mines of the company adjoin the Rialto on the east and south. Zinc-lead ores have been mined almost continuously from the Rialto tract since 1916. The property was acquired by American Zinc, Lead & Smelting Co. late in 1951, and the mine was operated thereafter by the Nellie B Division of that company until the end of 1955, when it was subleased to the Residue Mining Co.

Jan 1, 1958

By T. T. Chen, J. E. Dutrizac, C. Canoo

The calcine consists principally of ZnO and ZnFe2O4, which occur as banded and porous grains, together with lesser amounts of Zn2SiO4, Zn-Fe-Pb silicate, sphalerite, quartz, PbSO4 and Fe2O3. Al is present in solid solution in most of the Fe-bearing phases and also as residual aluminosilicate minerals from the original concentrate. Si occurs mostly as Zn2SiO4, Zn-Fe-Pb silicate and as residual silicate minerals. As is commonly found in the ZnFe2O4, Fe2O3 and Zn-Fe-Pb silicate phases. The major As carrier may be calcium arsenate particles less than 1 micrometre in size which are dispersed throughout the calcine. The neutral leach residue consists mainly of ZnFe2O4 and precipitated masses of iron gel-silica gel. Lesser amounts of ZnO, Zn2SiO4, Zn-Fe-Pb silicate, PbSO4, sphalerite, Pb-K-jarosite and basic zinc sulphate are also present. Al occurs in minor concentrations in most of the Fe-bearing phases and in the Zn-Fe-Pb silicate. The residual aluminosilicates are also an important Al carrier. The major As carrier is the precipitated iron gel-silica gel phase, but some As is also present in the Zn-Fe-Pb silicate, ZnFe2O4 and Fe2O3 phases. Silicon is divided about equally between the iron gel-silica gel, Zn2SiO4, Zn-Fe-Pb silicate and residual silicate minerals. The weak acid leach residue is generally similar to the neutral leach residue except for its reduced content of ZnO and basic zinc sulphate.

Jan 4, 1993

By J. W. Stewart

THE aim of this paper is to point out the various ways in which design is taught in standard four-year mining engineering curricula in American colleges and universities; to discuss the reasons apparently justifying the great diversity of procedure that exists along this line; and to indicate possible solutions to the difficulties now attending the teaching of design. A study was made of typical four-year mining engineering curricula in 15 colleges and universities of the United States (Table I). Great diversity in content of the various design courses, if taught as described, became apparent immediately. It appeared that it might be both interesting and instructive if the cause for this colorful variety could be found. Was the cause local mining conditions, departmental individuality, or actual necessity? Study of the school catalogues revealed that the various design courses could be classified into two fairly distinct types; namely, (I) those dealing with mine equipment or structures, and (2) those dealing with underground layout of mine workings. It seemed reasonable to label the first type of course "mining design" and the second type "mine design." Some such distinction must have been in the minds of mining educators, for we find both names (i.e., mine design and mining design) used to designate the design courses included in the various mining curricula. Unhappily, the name and the apparent content of such courses do not, in all instances, conform to the classification made here, although in most instances such conformation does obtain (Table I), It is possible that in the exceptional case the method of teaching a design course, and consequently the content of it, may have been changed at some time without change in the name of the course. Apparently only 3 of the I5 schools made an effort to cover both types of design in their curricula (Table I). Two other schools did not list or describe any course of study that could with certainty be taken as a design course. Of the remaining 10 schools, 9 gave a mining-design type of course and one gave a strictly mine-design type. Obviously, the preponderance of design courses afforded are of the mining-design type. Why? To answer this question, it is necessary to make a study of the prerequisites for the two types of design courses taught. In all schools the design courses were taught in the senior year; in eight, design was taught throughout both semesters; in two, it was taught during the first semester only; and in three it was taught during the second semester only. Consequently, excepting the last three cases noted, it is obvious that all prerequisites for a design course should be completed by the end of the junior year. PREREQUISITES What are the probable prerequisites for the different kinds of design courses as they appear to be taught? Let us take first the case of the mine-design type of course, having to do with layout of underground workings. Here it would seem that logical

Jan 1, 1941

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012