Search Documents

By Yuanbing Ling

Keywords: Calcium sulfate, Sulfuric acid, Phase transformations, Thermodynamic analysis As part of a boarder research project, seeking the development of a cost-effective process for direct production of the high value material, -calcium sulfate hemihydrate, from sulfuric acid at atmospheric as opposed to elevated pressure conditions, the fundamental work presented here has been undertaken. This includes experimental monitoring of phase transformation reactions and thermodynamic analysis of the relationships among the various phases, namely, calcium sulfate dihydrate, hemihydrate and anhydrite in aqueous sulfuric acid solution at temperatures ranging from 20oC to boiling point.

Jan 1, 2004

By Paul Biggs

This Bureau of Mines report contains information on 63 water flood projects in Colorado. Water was injected in 10 formations located in 58 oilfields. Specific field data presented include location, discovery, development, water supply, fluid injection, oil and water production, oil reserves, and oil recoveries by primary and secondary methods. An estimated 3.5 billion barrels of water has been injected to recover approximately 533 million barrels of oil, a ratio of 6.57 to 1. Most of the injection water is from alluvial deposits, although produced water is used in many fields. Injection water treatment is not a major problem. Appraisal of project success or failure in this report is based on technical, rather than economic, information.

Jan 1, 1974

By E. P. Klier, Taylor Lyman

THE structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davenport and Bain.1 Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etching, acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can be formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypoeutectoid steels. MECHANISM OF BAINITE FORMATION Davenport and Bain1 considered the mechanism of bainite formation to consist of two steps-an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide particles, (not lamellae), at a rate depending upon temperature. In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipitation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of "boom" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.

Jan 1, 1925

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

By Reichardt Y

Fine feed fractions in the size range from 1 to 40 ¦m of materials with different hardness as limestone and silicon carbide have been stressed in two different devices. A tungsten-carbide-blodc allows a single stressing with a pressure up to 2000 MPa and a 4-piston-block enables a multiple stressing procedure in which the material bed is stressed in alternating directions with a pressure up to 700 MPa. The experiments show energy absorption as the major factor for the interparticle breakage of hard material, like quartz, zircon silicate, silicon carbide and smelted oonindum, pressure, however, does not influence the results within the investigated range from 100 to 700 MPa and even up to 2000 MPa for corundum. But the breakage of the middle-hard limestone depends on the pressure so far as more fineness can be produced if the same energy is introduced at a lower pressure level. The creation of very fine and microfine fragments decreases strongly with increasing hardness of the feed materiaL The energy consumption for producing microfine material with a multiple stressing procedure on a particle bed is much lower than that one of a usual milling process. But this procedure needs a classification with a seperation cut at a couple of microns, which is not easy to accomplish.

Jan 1, 1993

By E. G. Noble

The potential for using heterotrophic microorganisms to solubilize manganese from low-grade domestic ores is being assessed at the Reno Research. center, U.S. Bureau of Mines. More than 90 pct of the manganese has been extracted from a variety of oxide ores in shake-flask tests using molasses as a source of .. nutrients for the microorganisms. It has also been demonstrated that high recoveries of manganese can be obtained from a domestic wad ore using column bioleaching. 'l'he isolation and identification of organisms responsible for manganese extraction is discussed, as are the mechanisms responsible for manganese solubilization.

Jan 1, 1991

By Veronique Falmagne

"In 1987 the only knowledge available of the Ansil orebody was that it was high grade, deep and relatively small . High stresses were also anticipated because there had been rockbursts during shaft sinking and destress blasting had been necessary (Fig. 1). From the design, through the development and now in the mining stage, rock mechanics and microseismic monitoring have been used to maximize recovery and safety and minimize dilution. Examples are given of the use of a microseismic monitoring system in the early stages o f mining. This paper also presents a review of the mine's in situ stress measurement campaign, cable bolting practice and backfill procedure.The Design PhaseAfter the initial mapping and classification work, preIiminary numerical modelling was performed using assumed stresses of ov = oH and oH = 3ov• The empirical Mathew's analysis was then used to optimize stope dimensions based on geomechanics data available at the time (Bawden et 01., 1988; Falmagne, 1987; Potvin et 01., 1988). Because of high stresses predicted by numerical modelling and a brittle, strong and relatively unfractured host rock which was believed to be rockburst prone, it was decided to mine without temporary or permanent pillars. However, in order to satisfy production rates, the orebody had to be broken up into two horiwns separated by a triangular pillar (Fig. 2). The final mining sequence is shown in Figure 3.The Development PhaseAt this point, based on work accomplished to date, including mapping and observations from drifting and modelling, the following problems were identified: (1) flat backs in the hangingwall andesite were thought to be highly stressed; (2) flat backs in weak massive sulphide ore would also be subjected to high stress and be difficult to support; (3) the felsic dyke was noted as a "" stress raiser"" , because activity increased as drifts approached it; and (4) chlorite coating of joints in the hangingwall was thought to be an important factor in reducing their stability."

Jan 1, 1991

By Thomas T. Read

Jan 1, 1913

By Hill G

The Boddington Gold Mine (BGM) is managed by Worsley Alumina Pty Ltd (Worsley) and is located 110 km south-east of Perth, Western Australia. The gold mine, which has operated since mid-1987, was originally constructed to treat 3 Mtpa of gold bearing oxide ores, has subsequently been expanded to treat 7 Mtpa and is presently one of the largest gold producing operations in Australia.During 1990 a Supergene/Basement Plant was constructed to treat 250 000 tpa of copper supergene and hypogene ores and basement ores which contain significant gold grades and which are encountered at the lower levels of the existing oxide orebody. The SupergeneBasement Plant has the versatility to treat a wide range of ore types, producing both gold bullion and copper-gold concentrates. It is a stand-alone facility adjacent to the existing 7 Mtpa gold plant.

Jan 1, 1992

By Arthur West

It is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 ions capacity each. In this, as in all the other stations described in this paper, each furnace is blown by two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines. The next station built is shown in Fig. 2. This is the plant of the Minnesota Steel Co. at Duluth, Minn., and is at present constructed for five engines, to handle two furnaces, with one spare engine. The engines are of practically the same size as those at Bethlehem. Instead of being arranged in right-hand and left-hand pairs, as at Bethlehem, all the engines are of the same hand; this arrangement has some ad-

Jan 1, 1915

By C. A. Stickels

In a recent paper, Held1 showed that rolling conditions can have a marked effect on the volume fraction of surface texture produced in low-carbon steel. This variation in rolling texture is reflected in the recrys-tallization texture and affects the plastic properties of the annealed sheet. The fact that roll friction can influence the surface deformation texture in iron and steel has been known for some time;'= but the magnitude of the effect has never been shown quite so clearly before. The analogous effect during wire drawing has been recognized for many year.4 Dillamore and Roberts5 examined surface textures in warm- and cold-rolled aluminum and copper. They found that when a surface texture was present it could be described as the interior texture rotated about the transverse sheet direction. The angle of rotation was a function of the type of lubrication, the amount of reduction per pass, and the temperature of rolling. The purpose of the present note is to show that surface textures in cold-rolled iron can also be described as interior textures rotated about the transverse sheet direction. Vacuum-melted electrolytic iron* was straight- rolled 90 pct at room temperature in a two-high rolling mill with 5-in.-diam rolls. Two rolling procedures were used: a) no lubrication with reductions of about 0.035 in. per pass, and b) heavy lubrication with lano-line and reductions of about 0.002 in. per pass. The final sheet thickness was 0.030 in. (110) pole figures were determined by transmission through specimens taken from the sheet surface and sheet midplane. The surface texture of the sheet cold-rolled according to procedure a is shown in Fig. l.* The shapes of the low-intensity contour lines indicate that the texture can be described as a partial fiber texture with a (110) fiber axis normal to the sheet. The approximate range of orientstions present is (011)[211] — (0ll)[100] — (011)[211]. This range of orientations is what one would obtain by rotating the interior texture 90 deg about the transverse sheet direction. The intensity of (110) and (222) reflections from planes parallel to the surface was measured after removing metal from the surface by chemical polishing. The surface texture here was confined to the outer

Jan 1, 1968

By Lloyd Williams

1. The investigation shows that the bed identified as Wilder in this report is the only bed in Overton County that has produced commercial coal and is the only bed in which coal reserves were estimated for this report. Three other coal horizons were recognized but lacked enough data for reserve estimates. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 19 million short tons, as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas of the Wilder bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By K. Howard Poulsen

Shear zones are tabular tructures which tend to occur either discordantly within, or concordantly along the margins of, competent rock masse uch as plutons, sill or flows. They contain deformed equivalents of their host rock and are common sites for gold mineralization localized in tructure oriented y tematically relative to the shear zones and internal linear fabric. Apan from genetic implications, hear zone analysis proves useful in exploration for this type of deposit because the zones are generally wider and more continuous than associated mineralization and because there is an element of predictability to mineralization geometry (i.e. vein orientation. plunge).

Jan 1, 1986

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957

By Hinde J. S

The Fitzpatrick Orebody is a three and a half million tonne fault bounded portion of the early-middle Proterozoic Broken Hill Orebody.The Fitzpatrick Orebody was discovered in 1975 by diamond drilling from the 36 Level Exploratory Drive. This followed persistent geologically oriented exploration and a courageous decision by mine management to deepen No. 3 Shaft to provide exploratory development across the Globe Vauxhall Shear and allow effective drilling of the target area.The stratiforrn oebody consists of three lenses, the lead rich No. 2 and 3 Lenses and smaller zinc lode. They represent a down plunge extension and boudinaged, fault-bounded portion of the main Broken Hill ore lenses. The surrounding host rocks are extensively faulted and jointed due to complex history of movement on the bounding shears. This results in extremely poor ground conditions during mining. The ore was delineated for mining development using three dimensional fan drilling from exploratory and hanging wall drive drill sites.

Jan 1, 1990

Improvements in computer technology and associated software have allowed the improvement and development of more advanced ventilation modeling software packages including those that have the ability to simulate the effects of a mine fire on the ventilation system in terms of heat, smoke and gas distribution. This ability has real applications for the mining industry in terms of emergency planning, training and response. The primary focus of this paper will be the benefits to training programs that this type of software can provide to all types of training for various personnel, from the newly hired inexperienced miner, mine rescue, atmospheric monitoring personnel and emergency evacuation drills. The results of the simulations can then be used to give miner?s more detailed information on what types of conditions they may face based on the type and location of the fire and the program itself can be used to manipulate the ventilation system in a way that emergency response personnel may (i.e. tear down stoppings to reduce airflow to the fire area) and see the effects in real-time.

Jan 1, 2012

By James M. Barker

Sulfur is a nonmetallic element of great physical and economic importance to the world. It is widely but sparingly distributed throughout the hydrosphere, lithosphere, and biosphere. Sulfur is the tenth most abundant element in the universe and eighth most abundant in the sun. In the earth's crust, which is mainly igneous, it ranks 14th, but is eighth or ninth in sediments (Kaplan, 1972; Stanton, 1972). It apparently is very abundant in the core of the earth, because it is a strong chalcophile, and it is fifth in abundance in stony and iron meteorites (Field, 1972) where it occurs as trolite (FeS). In ancient times sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Shelton (1979) summarized most of the common definitions of terms, grades, and specifications for the sulfur industry as follows (with minor additions): Sources of Sulfur: Combined sulfur-Sulfur that occurs in nature combined with other elements. Cupriferous pyrites-Pyrite containing relatively minor amounts of copper sulfide minerals. Hydrogen sulfide-A toxic gas (H2S) occurring in natural gas and petroleum. Involuntary sulfur-Sulfur produced primarily as a result of legislative or process mandates. Native sulfur-Sulfur that occurs in nature in the elemental (uncombined) form. Nonferrous metal sulfides-Copper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfurs-Complex organic sulfur compounds occurring in petroleum, coal, oil shale, and tar sands. Pyrites-Iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfurs-Sulfur in anhydrite and gypsum. Voluntary sulfur-Sulfur produced in response to market forces. Basic Sulfur Products Produced and Marketed: Acid sludge-Contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-Synonymous with crude sulfur. Bright sulfur-Crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-Solid crude sulfur crushed to -8 in. Byproduct sulfuric acid--Sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-Commercial nomenclature for elemental sulfur. Dark sulfur-Crude sulfur discolored by minor quantities of hydrocarbons ranging up to 0.3 % carbon content. Elemental sulfur-Processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-Elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-Elemental sulfur produced from native sulfur sources by the Frasch mining process. Hydrogen sulfide-Associated with natural gas or petroleum and produced at refineries and coke oven plants; used to make sulfuric acid or recovered sulfur. Liquid sulfur-Synonymous with molten sulfur. Liquid sulfur dioxide-Purified sulfur dioxide compressed to the liquid phase. Molten sulfur-Crude sulfur in the molten phase.

Jan 1, 1983

By Robert B. Parsons

"Originally intended to be implemented in 1977, but actually introduced effective May 6, 1974, the earned depletion regulations have been substantially refined and modified since their appearance on the Canadian tax scene, so that this important legislation now consists of a highly complicated set of rules which even the most astute follower of tax law has considerable difficulty sorting out!This month, Tax Notes attempts to cut through this bewildering array oj regulations, in reviewing the main features of the earned depletion allowance applicable to mining operations. Despite the phase-out of earned depletion allowances for most oil and gas operations as part of the federal government's new National Energy Program, earned depletion provisions are still alive and well for the mining sector, although they might well be slowly strangling to death in their own entanglement of complexity!"

Jan 1, 1981

By S. W. Zoldok

[The Bull Valley iron-ore district lie,; in the northern part of Washington County, Utah, approximately 30 airline miles southwest of the highly productive Iron Springs area (fig. 1). Iron-ore occurrences in the district have been known for many years, but they have not been mined, largely because of the inaccessibility of the area. The Bureau of Mines established a development project in the Bull Valley district in September 1941. Two separate areas, the Pilot and the Cove Mountain, were investigated. The work was planned to increase iron-ore reserves for steel production in the Western United States. During the project period three diamond-drill holes aggregating 1, 000 feet were completed (fig. 2). The program also included 6 408 linear feet of surface trenching and 171 feet of underground work (figs. 2 to 8, inclusive). Analyses were made of 460 samples from the diamond-drill holes and surface and underground excavations. The results of the analyses are given in tables 1, 2, 4, and 5, and the logs of the diamond-drill holes are shown in table 3. Field. work was completed in September 1942.]

Jan 1, 1953