Search Documents

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By Jian Deng, Hehua Zhu, Lianyang Zhang

Rockburst is defined as a sudden and violent explosion of rock on the surface of a rock excavation. Rockburst has been regarded as the least understood and most feared hazard problem for underground rock excavations. Traditionally, rockbursts were classified into the strain, pillar, and fault-slip categories. However, rockbursts are also known to occur at stress levels well below the rock yield strength, in mines where the rock is far from brittle, or without the presence of geological discontinuities. A plausible explanation of rockbursts is buckling, which has been identified as one of the main mechanisms for rockbursts. It is observed that rockbursts are often induced by dynamic loadings (pulses) from adjacent blasting. Therefore, the present paper studies the effect of pulse shape and amplitude on pillar rockbursts induced by dynamic loadings from blasting using the method of numerical analysis. The governing equation of a pillar’s motion is set up and the mechanism of pillar rockbursts is investigated through a practical example. The results show that it is not the shape of a pulse but the impact energy to decide the occurrence of pillar rockbursts. If all other parameters remain the same, pillar rockbursts are more likely to occur when the pulse duration is longer. The parametric resonance and the perturbation of dynamic loadings are also found to play an important role in the occurrence of rockbursts. These insights would provide invaluable clues about the mechanism and for better control of pillar rockbursts.

Apr 26, 2022

By Foluke Salgado de Assis

Este trabalho visa apresentar alguns resultados obtidos através de ensaios balísticos realizados em sistemas de blindagem multicamada. Seguindo as especificações da norma americana NIJ 0101.06, foram realizados ensaios utilizando munição de calibre 7,62x 51 mm, que possui velocidade acima de 800 m/s. A blindagem multicamada utilizada possui como camada frontal uma pastilha hexagonal cerâmica (alumina dopada com 4% de nióbia), segunda camada de compósito de matriz poliéster reforçada com tecido de juta e como terceira camada uma placa de alumino 5052 H34. A utilização de compósitos poliméricos reforçados com fibras naturais em substituição às fibras de aramida é de grande interesse, pois além de desempenharem a mesma função no sistema de blindagem, possuem um valor de mercado bem menor. Com os resultados obtidos do ensaio balístico, os valores foram associados com o seu comportamento dinâmico utilizando o método do casamento de impedâncias.

Aug 17, 2017

By Peter H. Toepfer

This report presents the factual data obtained by the Bureau of Mines during diamond-drilling investigation of the Sunset copper deposit in the Index mining district, Snohomish County, Wash. The Sunset mine, first produced copper ore in 1902, but its main period of activity was from 1923 through 1930, The mine has produced 263,500 tons of ore, from which 1,500 ounces of gold, 156,000 ounces of silver, and 12,912,000 bounds of copper-were recovered. The mine has, been idle since 1946

Jan 1, 1953

By Antonio Lourenço Batista de Souza

Neste trabalho, foi desenvolvido um modelo de elementos finitos para simular o primeiro passe da laminação de tiras a quente de aços C-Mn, durante a etapa de acabamento, via DEFORMTM3D. As dimensões e condições de processo foram obtidas a partir de dados industriais descritos na literatura. Utilizando-se o modelo termomecânico, foram feitas análises de sensibilidade por meio de alterações no fator de atrito e coeficiente de transferência de calor por condução, uma vez que não há um conhecimento preciso dos valores destes parâmetros para o processo simulado. Com isto, foram analisadas as alterações que a mudança destes parâmetros podem causar na carga e temperatura de laminação, perfil de deformação, fração recristalizada e tamanho de grão. O aumento do atrito provoca um aumento na carga de laminação, na homogeneidade do perfil de deformação e menor tamanho de grão. O aumento no coeficiente de transferência de calor, diminui a temperatura superficial da tira, o tamanho de grão e gera um aumento na carga de laminação. Assim, neste estudo foi mostrado a eficácia do modelo em predizer o comportamento do aço no processo de laminação a quente.

Aug 16, 2017

By Benjamin C. Craft

A review of development in North Louisiana during 1936 centers around the Rodessa field, in Caddo Parish. Continued extension of the

Jan 1, 1937

By H. P. Greenwald, H. C. Howarth

There was reported in Bureau of Mines Technical Paper 5754/ a series of tests to determine the compressibility and bearing strength of specimens prepared from blocks of potash salt obtained from a mine near Carlsbad , N. Mex . The events leading up to the investigation were sketched in a foreword by George S. Rice , then chief mining engineer of the Bureau ( retired September 30 , 1937 ) ; this foreword also gives a discussion of the possibility of increasing the ultimate total recovery of the potash salt by " second mining" of pillars or by use of a longwall system . In June 1936 , Rice and the senior author visited Carlsbad with H. I. Smith , chief of the mining division of the Geological Survey , to observe mining then in progress and to discuss with the management of one of the mines records of convergence of roof and floor which they were obtaining . It developed that serious thought was being given to the possibility of roof failure resulting from shear at the faces of pillars . There was envisioned the danger of such cracks extending upward to water - bearing strata . Obviously , the simple compression tests of the potash salt then being made would throw no light on this question , and tests of assemblies of potash and roof salts would have to be made . In this connection it is to be remembered that in the mine no sharp division exists between the potash salt being recovered and the nearly pure halite which forms the roof . The interlocked crystalline structure is continuous , and there is merely a very rapid decrease in the proportion of sylvite in a short distance vertically . Figure 2 of Technical Paper 575 shows that two samples near the top of the salt being mined contained , respectively , 51 and 65 percent potassium chloride . Contrasted with this is an analysis of the roof salt given on page 24 of that publication , which showed only 3.6 percent potassium chloride . As the data given in Technical Paper 575 show , the roof salt is much less plastic than the potash salt . The immediate roof may then be thought of as a more rigid stratum of indefinite extent resting on and continuous with yielding supports and loaded uniformly at the rate of 900 to 950 pounds per square inch . Just what thickness of the salt should be considered as immediate roof is uncertain .

Feb 1, 1938

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By O. G. Olvera

"Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Typical cyanide operations show poor performance and require oxidative pretreatments to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. This work focuses on evaluating the effect of the addition of a carbon resin as a sulfur collector on the oxidation of different arsenopyrite concentrates under atmospheric tank leaching (ATL) conditions. The addition of the resin improved the oxidation of sulfides and favored the formation of elemental sulfur over the generation of sulfate. The use of AF5 in ATL resulted in higher gold recoveries under standard cyanide carbon-in-leach and thiosulfate leaching.INTRODUCTION Refractory sulfidic ores consist of materials in which gold occurs finely disseminated within metallic sulfides or forming solid solutions, with pyrite and arsenopyrite being the two sulfides most commonly associated with gold. Gold is not readily accessible to solutions in these types of ores and typical cyanide operations show poor performance, thus making the use of oxidative pretreatments a requirement to increase gold recovery. Pretreatment alternatives include roasting, pre-aeration, acidic and alkaline high pressure oxidation, and bacterial oxidation. The presence of arsenic, however, introduces a serious disadvantage to the use of roasting and bacterial leaching, while high pressure oxidation involves high capital costs. The use of carbonaceous materials to enhance the dissolution of sulfides is not novel, and leaching additives such as coal, activated carbon and carbon powder have been considered for the improvement of bioleaching, atmospheric leaching, and pressure oxidation leaching processes. However, this type of technology has been focused mainly on the recovery of copper from copper concentrates containing chalcopyrite with less attention paid to other sulfides."

Jan 1, 2017

By Kenneth Maas

The Bureau of Mines devoted portions of the 1987-1988 field seasons to investigate the mineral aggregate industry in Juneau, Skagway, Haines, and Gustavus, Alaska, as part of the Juneau Mining District study. Statistics compiled for current suppliers include location, activity, reserve estimates, expected mine life, and types of commodities available. Each population center, except for Gustavus, is well endowed with suitable mineral aggregate to last at least 20 years. The Bureau of Mines quantified the mineral aggregate resource in many large potential sites within each area. Sampling, engineering and soil-index testing, site descriptions, deposit dimensions, and gold recovery information is described. Refraction seismic studies performed at three localities revealed gravel thicknesses in excess of 40 to 80 feet. In the Juneau area the Herbert/Eagle Rivers outwash area, East Fork Lace River. Antler/Gilkey Rivers, and Grizzly Bar (Taku Inlet) individually contain in excess of 60 million yd3 of excellent-quality aggregate with minor accessory gold credits. Haines is also well endowed with aggregate resources; large, quality deposits occur along and at the confluences of the Chilkat, Katzehin, Klehini, Tsirku, and Kicking Horse Rivers. Large deposits of granitic aggregate exist in the Skagway River and East Fork Skagway River.

Jan 1, 2012

By Robert Maes, Robert de Strycker

The Cu-Sn-As systeM was studied in the region near the Cu-42 and (214-As binary diagrams, where reactions in the solid state appear, resulting from the decomposition of the y(Cu-Sn) phase and from the formation of the 7 phase (Cu,As). The techniques used were microscopic observation, thermal analysis by dilatometry, and X-vay diffraction. The formation of the 7 phase gives rise to a ternavy pevitectoid veaction; the decomposition of the y phase gives rise to five transitional reactions. The temperatures of almost all these reactions could be determined; in the most favorable cases , the accuracy of this determination was of 11.5-C. The 7 phase is stabilized by tin additions, the arsenic atoms being replaced by tin atoms up to 35 pct; this has allowed the preparation of pure j) phase and the confirmation, by extrapolation, of the conrposition of this compound in the Cu-As diagram. In the first part of this work, the solidification reactions in the Cu-Sn-As phase diagram were studied. In the copper corner, the structure of the alloys presented the evidence of reactions in the solid state: on the one hand, all the alloys containing the y phase of the Cu-Sn diagram showed, under the microscope, that this phase had formed different decomposition products after complete solidification; on the other hand, the appearance of the 7 phase of the Cu-As diagram necessitated the introduction of a peritectoid formation reaction. The study of the decomposition of the y phase has been done by preparing about forty alloys that were homogeneous y at high temperature. The formation of the 7 phase has been studied by means of a few alloys with a composition near the homogeneity field of this phase at room temperature. The part of the Cu-Sn phase diagram of interest for this study is represented by Fig. 1, with the phase designation which will be used in the remainder of this paper; it is drawn after Hansen and Anderko.' The Cu-As diagram has already been presented in Part I of this work; the significant features of this study are the existence of the arsenides CusAs and Cu5Asz, and the formation of a compound CUEAS, designated as the 7 phase, by a peritectoid reaction at about 325°C. EXPERIMENTAL METHODS The fundamental technique for the investigation of this part of the Cu-Sn-As constitution diagram was microscopic observation; the greatest part of the observed alloys has also been subjected to thermal analysis by dilatometry; a few selected alloys have then undergone an X-ray analysis by powder diffraction. Alloy Preparation. The alloys were prepared from the same products as in Part I of this study: cathode copper, arsenic with a purity better than 99.5, and tin with a purity of 99.98. The fusion of the ternary alloys was realized from

Jan 1, 1967

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By Bertrand L. Johnson

Before 1914 , Chile , because of her extensive resources of natural nitrates , practically monopolized the world markets for one of the leading fertilizer materials . Since nitrogen also is an important war material , constituting in fact the principal ingredient in many high-powered explosives , the World War and the widespread insistence upon national self- sufficiency for war materials brought about the development of nitrogen fixation plants in all of the larger countries . The production of by- product ammonia from gas and coke plants was likewise stimulated . As a result , Chile , even after the ocean lanes were reopened , was forced to fight for her lost markets . Since the world capacity to produce is still far in excess of annual consumption , the competition between natural and synthetic supplies has been keen and prices have fallen below pre-war levels . Chile has recently succeeded in unifying her industry , utilizing the most efficient process now in operation, and the Government is a partner in the new company that will take over all of the present producing companies . These developments place Chilean nitrate of soda , in a much more favorable position among the markets of the world . More intense competition will undoubtedly follow and , in order that those interested may become familiar with the fields upon which the nitrogen conflicts of the near future may be waged , the following general summary of the nitrogen industry has been prepared .

Jan 1, 1931

By J. S. Dunning

Recent developments in energy conversion, mining and minerals processing, pollution control, and chemical equipment have placed in-creased demands on heat-resistant alloys. Higher corrosion rates from oxidation, hot corrosion, and sulfidation have increased consumption of materials that contain critical and strategic minerals and in many cases have limited productivity. The Bureau of Mines is conducting re-search on substitute materials having greater resistance to high-temperature corrosive atmospheres above 6000 C compared to austenitic stainless steels such as AISI 304, 316, and 310, with the goal of conserving critical metals such as Cr and Ni. The substitute materials are based on Fe-Cr-Ni-Al compositions. Aluminum additions to Fe-Cr-Ni alloys significantly improve high-temperature corrosion resistance, particularly sulfidation resistance. In the alloy, devised by Bureau researchers, aluminum additions are held in the form of a second-phase precipitate, 8NiAl. Minor additions of Ti, Mn, and Si improve workability.

Jan 1, 1984

By A Esfahanipour, M Osanloo

Determination of cut-off grade?strategy is one of the most important stages of open pit mine planning and design. It is the parameter directly influencing the financial, technical, economic, legal, environmental, social and political issues in relation to mining operation. Choosing the optimum cut-off grade strategy that maximises the economic outcome has been a major topic of research workers for nearly one century. Many researchers have contributed in devising methods and algorithms, such as dynamic programming, linear programming, optimal control and so on for various aspects of its determination. In this paper, a non-linear mathematical programming for cut-off grade strategy optimisation is presented, considering the three main stages of mining operation introduced by K F Lane. In this model maximisation of net present value of mining operation, under the three constraints of mining stagesÆ capacities, considered as the optimisation criteria. Due to the discrete representation of the mining resource, the proposed non-linear formulation is approximated by a non-linear signomial geometric programming. According to non-convexity and the complexity of the proposed model, an augmented Lagrangian genetic algorithm was used to find the optimum cut-off grade strategy under varying and fixed price circumstances. To validate the proposed non-linear model efficiency, the results were compared with the results obtained by the K F Lane methodology. It was found that the proposed non-linear model works efficiently in the determination of cut-off grade strategy. According to the simplicity of the structure of non-linear programming modelling in comparison with dynamic programming it is hoped that, further development of this model would certainly provide the ability of considering managerial and technical flexibilities as well as incorporating more real mining conditions in the determination of cut-off grade strategy optimisation.

Sep 26, 2011

By D. R. Derry

"IT WOULD TAKE a braver man than I to try to forecast the future of mining exploration far into Canada's second century. Even to look ahead ten or twenty-five years we must review the figures of the fairly recent past -and I have found this quite a time-consuming but interesting job -in order to find trends and project them into future years. The trends to which I will refer are: firstly, the annual expenditure on exploration and its relation to value of output; secondly, the discovery rate and its relation to production initiations; and thirdly, the methods by which discoveries have been, and will be, made. Exploration Expenditures Figures on the annual expenditure on mining exploration in Canada have been collected and published for some years by the Do-minion Bureau of Statistics. These have some unavoidable limitations; e.g., in the varying definition between one company and another of what comprises ""Exploration"" and in the difficulty of getting complete returns. However, although the actual figure for a given year may be subject to question, I believe that the relative figures from one year to another are reasonably reliable. There is also a lapse of time between the collection of data and publication -the last published figures are for the year 1963. In bringing the figures up to date to 1966 I have canvassed eight of the larger mining and exploration companies and obtained their figures for 1963 to 1966 inclusive, and then averaged these for each year and applied the progression to the 1963 figures."

Jan 1, 1968

By A. L. Engel

This report is a compilation of results of brief preliminary tests on sulfide ores that contained gold and silver and, in some cases base metals. It is a companion paper to a recent similar report on oxide ores. Simple treatment methods employing the least possible equipment sometimes produce satisfactory results on marginal ores and in small-scale operations. Investigations of typical ores from newly discovered or recently explored mining districts have been made in continuation of a long-established part of the hydrometallurgical and ore-dressing program of the Reno station, Bureau of Mines. The purpose of such investigations is to encourage the search for and development of mineral resources and particularly to assist in the economical exploitation of low-grade and marginal ores as well as the conservation and recovery .of values in products that were discarded from former operations because of inability to treat them profitably. Several of these investigations have been limited to preliminary tests of samples from prospecting operations, whereas same involved samples of old dumps or tailings piles. The test work in these cases was not extensive enough to warrant publication as individual reports, but is of considerable interest inasmuch as it indicates the possibilities as well as the limitations of treating the respective materials. The samples were representative of the districts from which they wore obtained, so this information should be helpful in the future development of these districts.

Jan 1, 1951

Spirals have become one of the most popular methods for treating fine coal. Unfortunately, spirals tend to produce an undesirably high specific gravity cut-point and often misplace significant amounts of coal and/or rock. In the present study, a process-engineering tool known as linear circuit analysis was used to identify problems with traditional spiral circuits and to suggest alternative configurations. These analyses indicate that a modified rougher-cleaner circuit incorporating a middlings recycle stream offers the best option for improving performance while maintaining a reasonable circulating load. In light of this finding, a full-scale test circuit was installed and evaluated at an existing preparation plant. Data obtained from the plant tests indicate that the new spiral circuit can simultaneously reduce cut-point and improve separation efficiency. Preliminary economic analyses show that the new circuit provides an attractive payback on the capital investment.

Jan 1, 1998

By Késsius Bortolan Menezes

O complexo Minas-Rio da Anglo American iniciou suas operações em agosto de 2014. A usina de tratamento produziu, em 2016, cerca de 15,5 milhões de toneladas de concentrado. O minério, explorado em Conceição do Mato Dentro (MG), passa pelas etapas de cominuição, classificação, concentração e separação sólido-líquido antes de ser bombeado por 529 km até São João da Barra (RJ), onde é filtrado, estocado e embarcado para exportação. Durante a fase de projeto, a utilização de equipamentos pilotos com capacidade de centenas de quilos por hora foi de fundamental importância para verificação da viabilidade técnica do tratamento do minério. Contudo, a realização de um teste exigia um esforço muito grande, devido aos grandes volumes de minério necessários. Por isso, com o início das operações, os testes em escala de bancada começaram a ser mais explorados. Além deles, testes em mini planta piloto com capacidade de dezenas de quilos por hora são muito utilizados, pois permitem simular de forma simples diferentes circuitos. O trabalho tem por objetivo mostrar essa evolução histórica na utilização de ferramentas para avaliação do desempenho da flotação, com exemplos de resultados práticos obtidos, e como os mesmos influenciaram a tomada de ações que culminaram em melhorias industriais.

Oct 30, 2017

By Gabriel Oliveira Glória

Como uma boa alternativa a outros materiais, o número de materiais ecológicos está aumentando. As fibras naturais estão substituindo fibras sintéticas, por exemplo, a fibra de vidro. Além dos aspectos ambiental, as fibras naturais são mais baratas do que os sintéticos. A caracterização do FTIR é um indicativo sobre a possibilidade de integração de fibras com as matrizes de polímeros e compósitos ambientais. Portanto, o presente estudo analisou a fibra de PALF por meio de espectroscopia FTIR. O espectro mostrou principais bandas de absorção típicas de interacções moleculares específicas de fibras PALF. A análise FTIR do permitiu a identificação de grupos funcionais moleculares de fibras PALF e as suas características de vibração.

Aug 17, 2017