Search Documents

By J. Chipman, N. J. Grant, J. H. Walsh, T. B. King

WITH the development of adequate sampling and analysis techniques, much information has been obtained concerning the behavior of hydrogen in the steel bath during the course of steelmak-ing operations. From studies of this type it has become clear that the slag has an important role to play in determining the hydrogen content found in commercial products. A knowledge of the behavior of hydrogen in slags is necessary to round out our knowledge of hydrogen in steelmaking practice; with this information we are better able to assess practical methods of control. In this paper a method developed for analyzing slags for hydrogen content, studies of the solubility of hydrogen in synthetic slags, and studies of the variation of hydrogen content in slag and steel in industrial heats will be described. Previous Work—While very little has been done in the past to determine the hydrogen content of metallurgical slags, measurements have been made on such slag-like materials as geologic magmas and glasses. Goranson as made extensive studies of the solubility of water in natural and synthetic granites. Many workers have investigated the solubility of gases in synthetic and commercial glasses, but the recent work of Russell" is the most extensive. Russell found that the solubility of water in glass was proportional to the square root of the water vapor pressure in water vapor-oxygen mixtures. It was found that the solubility could either increase or decrease with temperature depending on the glass composition. Wentrup, Fucke, and Rief,' and Piper, Hagedorn, and Backes' have extracted hydrogen by holding a slag at 1300" and 800°C respectively in vacuum. Wentrup et al. reported hydrogen and water vapor as evolved together while Piper et al. passed the evolved gases from the hot extraction treatment over hot ferromanganese to reduce the evolved water vapor to hydrogen and, therefore, reported the analyses in terms of total dissolved hydrogen. Yavoiskii has reported hydrogen and nitrogen analyses on steelmaking slags. Dobrokhotov, Povol-skii, and Khan have studied the hydrogen content of basic open hearth steel under slags of varying viscosity. These authors reported that the hydrogen content of the steel bath increased as the fluidity of the slag was increased by the addition of bauxite. They recommended that a viscous slag be used and the steel tapped without deoxidation in the furnace to ensure a low final hydrogen content. Analysis of Slags for Hydrogen Development of Apparatus—The vacuum fusion analysis equipment described by Shields, Chipman, and Grant" was modified for the analysis of slags." This method depends upon the reduction of water in the slag to hydrogen, which is readily determined by the method used for hydrogen in steel. Preliminary experiments were made with a eu-tectic ferrosilicon melt as the reducing agent. Other experiments included the use of graphite and molybdenum crucibles. The ferrosilicon alloy bath was found to produce a thick coating on the furnace tube which could adsorb hydrogen. Graphite produced CO by the reduction of FeO, MnO, and SiO2 in such quantities that analysis for hydrogen was virtually impossible. Molybdenum, while giving a low blank value, could reduce the slag sufficiently to produce a volatile oxide which again was found to adsorb hydrogen. The arrangement finally adopted is shown in Fig. 1. The molybdenum sheet served as the induction-heated susceptor, and was separated from the escaping gases by alumina guide tubes. An outer jacket of alumina protected the quartz furnace tube, and alumina and quartz stools completed the assembly. The falling sample is shown wrapped in aluminum foil, 0.002 in. thickness, which acted as the reducing agent' This foil was careful'~ washed in acetone and an d and then dried in hot air before wrapping the weighed slag sample for charging into the apparatus. Investigation of the hydrogen content of the aluminum foil itself showed that a small quantity of hydrogen was released in vacuum, but had no relation to the weight of the aluminum charged. This quantity of hydrogen was

Jan 1, 1957

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By L. Cheng, Y. W. Pan, Y. R. Liu

"Impounding deformation of slope and foundation is significant during and post dam construction. Reservoir impoundment is accompanied with various phenomena, including material degradation, effective stress decreasing and buoyancy in rock masses. These phenomena are related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope, which finally led to failure and landslide. Pore pressure in jointed rock masses is considered in constitutive relation. The expression of effective stress for porous rock with fluids is incorporated into the Drucker-Prager criterion. Based on monitoring data of valley width and dam deformation, the effective stress law is applied to analyse the impounding influence of slope and foundation to Jinping-I high arch dam. The dam is accompanied with complicated topographical and geological conditions. The results show that calculated and monitored values agree well, and the application of effective stress law provides an approach to evaluate dam deformation, stress and stability with impounding effect considered.INTRODUCTIONImpounding deformation of slope and foundation is a common and significant problem during dam construction and operation. This phenomenon exists in a lot of reservoirs in China, like Laxiwa, Ertan, Xiluodu and Jinping-I arch dams, and some dams in Europe. It is related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope. Monitored data indicates that the valley width tends to shrink in hydraulic engineering during the impounding process, which will change the stress and deformation of dam and abutment. Therefore, global stability of dam and foundation should be evaluated with impounding process taken into consideration."

Jan 1, 2015

By M. T. Ityokumbul

The use of yield index, the product of the yield and gangue rejection, for the optimization of separation processes is presented. The characteristics of the yield index are contrasted with separation efficiency calculations and applied to laboratory froth flotation and washability data. Data from continuous froth flotation tests conducted to "optimize" froth flotation using process optimization software were also evaluated with the yield index procedure.

Jan 1, 1997

By L. Zhou, L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly; however, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics, namely size and location, are of great importance in reducing the risk of mine fire injuries. A new improved fire location algorithm has been developed and integrated into an Atmospheric Monitoring System (AMS) program by researchers from the National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

Sep 29, 2020

By George R. Schottler

The objective of this research is to find the extent of the range of applicability of previously developed statistical methods for determining grade and tonnage of ore to bedded uranium deposits. Uranium assays obtained from gamma-ray logs of exploratory drill holes are used to compute grade and tonnage of ore in the deposit by a standard polygonal method and by statistical analysis. The results obtained by the two methods are compared. The uranium-assay frequency distributions are shown to be lognormal and a simple transformation permits the use of standard normal curve statistics. The effects on the assay frequency distributions of stratified sampling, a required minimum mining thickness, and increased assay-interval length are investigated. The addition of low-grade mineralization to make up the required minimum mining thickness results in a distinct change in the skewness of the assay frequency distribution. Any statistical inference regarding grade-tonnage relationships that will be produced, using the minimum mining thickness, should be made on the basis of this "revised" assay frequency distribution.

Jan 1, 1965

By C. Özgen Karacan

Gamma ray, density, sonic and core logs obtained from two boreholes drilled over a longwall panel in Southwestern (SW) Pennsylvania were analyzed for formation boundaries, log-derived porosities and densities and for rock elastic properties from sonic transit times. Gamma ray (GR) and density logs (DL) were analyzed using univariate statistical techniques and fractal statistics for similarity and ordering of the log data in depth. A Fourier transformation with low-pass filter was used as a noise elimination (filtering) technique from the original logs. Filtered data was tested using basic univariate and fractal statistics, rescaled range (R/S) and power spectrum (PS) analysis to compare the information characteristics of the filtered logs with the original data. The randomness of log data in depth was analyzed for fractional Gaussian noise (fGn) or fractional Brownian motion (fBm) character. A new prediction technique using radial basis function (RBF) networks was developed to calculate shear and Young?s moduli of the formations when sonic logs are not available. For this approach, the filtered logs were used as input to an RBF based upon a combination of supervised and unsupervised learning. The network was trained and tested using rock elastic properties calculated from the sonic log of one of the boreholes. The network was used to predict the elastic and shear moduli of the coal-measure rocks over a longwall coal mine in SW Pennsylvania. This approach demonstrated that it could be used for prediction of elastic and shear moduli of coal-measure rocks with reasonable accuracy.

Jan 1, 2009

By R. Hans

Removal of toxic anions from aqueous solution was studied using a Magnetic Ion Exchange (MIEX) resin which is a polyacrylic, strong base resin. Gravity based settling is made more efficient due to the magnetic nature of the resin which is advantageous over conventional ion exchange resins. In addition, the magnetic microspheres of MIEX have larger surface area in comparison to conventional ion exchange resins. Over the years MIEX has been successfully used and has gained significant popularity for efficiently removing dissolved organic matter from wastewater and groundwater. In the present study the efficiency of the MIEX resin was tested for the removal of chromium(VI), molybdenium(VI), vanadium(V) and arsenic(V) anions. Effects of pH (2-10) and temperature (25oC-55oC) were examined. In general, low solution pH values were favorable for anion uptake by MIEX. Except for chromium(VI), the metal ion uptake was significantly increased by the increase in solution temperature. The adsorption data were analysed on the basis of chemical speciation and heterogeneous kinetic models.

Jan 1, 2014

By Y. M. Zhao

The dry coal preparation technology based on air dense medium fluidized bed is an innovative dry highly efficient technology of coal by introducing fluidization technology into beneficiation.. A modularized 40-60 tones/hr system (KZX-40) with an air dense medium fluidized bed separator was established. The construction cost of the modularized system is only 1/3 of the traditional wet heavy-medium coal preparation plant construction cost with the same capacity, and the consumption of dense medium can be reduced by 50%-60%. The footprint and volume of the system are decreased by 75% and by 89.81%, respectively. These facts show the improved intensity, efficiency and economy of modularized coal preparation technique. The modularized KZX-40 system can be used to separated 50-6 mm coal over a separation density range of 1.3-2.2g/cm3 depending on the variation of <1mm fine coal content. The separation efficiency of the system was investigated at low and high separation densities by float-sink experiments. The partition curve of the products at low separation density shows that the separation density (d) is 1.33g/cm3, and the probable error (E) value is 0.05g/cm3. Using 50-6mm coal with an ash content of 55.35% as feedstock, at a high separation density of 1.61g/cm3, the clean coal with an ash content of 14.67% and the tailing with an ash content of 71.26% are produced with an E value of 0.06g/cm3. It is clear that the modularized KZX-40 system is suitable for separating 50-6mm coal effectively. During the dry coal preparation process, the dust is removed by the bag collector and recycled back into the separator. So the system has the advantages to work without environmental pollution and water. The modularized system greatly reduces the construction and operating costs and decreases the area and volume required, compared with wet dense medium system. The system is applicable to the coals located in arid regions and also to the coals that tend to slime during wet separation. Keywords: modularized, KZX-40, fluidized bed, beneficiation

Sep 1, 2012

By C K. Bell, L. S. Collett

An AFMAG survey was flown in 1968 over the Upper Nelson River area, Manitoba. The flight direction was northwest-southeast and flight spacing was 2 miles. In the Cross Lake Subprovince, AFMAG showed that an isolated peridotite outcrop was part of a dike that extended over 80 miles. Diabase dikes are not always marked by an anomaly, but isolated cross-overs, when used in conjunction with geological and magnetic data, permit their extrapolation. Anomalies coincide with areas of sulphide mineralization. In the Flin Fion Subprovince, known and unknown northeast-trending faults are detected. The Berry Creek fault was extended south through Tramping lake, then under the Paleozoic cover. Conductors were detected at, or near, the axes of major synclines within Amisk and Snow Group sediments. Granitic terranes have low conductivity and, because they are characterized by smooth AFMAG profiles, they can be delimited. AF.MAG is being recognized as a geophysical method that can aid geological mapping and interpretation. Its most important contribution to the geologist will be in regions where out-crops are sparse.

Jan 1, 1971

This report summarizes the cost of U.S, mining and milling industry compliance with the Environmental Protection Agency (EPA) interim water quality guidelines for waste discharges. Applicable excerpts from Public Law 92-500 are stated and interpreted in conjunction with the guidelines being used for implementation of the law. Over 200 U.S. Army Corps of Engineers applications for discharge permits were used to develop the quality and quantity data base needed to estimate the cost to comply with EPA guidelines, Cost of three basic treatment methods were considered: Aeration, addition of lime, and sedimentation. From the process design, cost-capacity graphs were developed to consider maximum flow rate, maxi lime addition, and average flow rates. The graphical method used in this evaluation should provide a reasonable guide to the effect of waste treatment and, therefore, Public Law 92-500 and corresponding EPA guidelines on the mineral processing industry. The cost of complying with the EPA guidelines will have the effect of prompting the mining industry to minimize the production of waste water and of undertaking some additional treatment, Two case studies are presented to illustrate efforts that might be fruitful for minimizing waste water production and for treatment of combinations of acid mine drainage, mill wastes, and metallurgical process wastes when treatment is deemed necessary.

Jan 1, 1975

By J. J. Gusek

Passive treatment of mine drainage using constructed wetlands has been employed on coal and metal mine sites since about 1985. The technology has advanced significantly since then; there are currently over 600 of these systems treating coal mine drainage in the Eastern U.S. at flow rates of hundreds of liters per minute. Passive treatment performance at three metal mines discussed in this paper has been positive for a wide variety of flows, water chemistry, and climates. The sites include a high-altitude underground copper mine, acidic seepage from a gold heap leach pad, and pumped effluent from an active underground lead mine in Missouri.

Jan 1, 2000

By W. G. Mine

In September, 1953, seismographs were installed in the Crowsnest Pass area of Alberta and British Columbia to study the &apos;bumps&apos; which were occurring in the coal mines at Fernie and Coleman, and to investigate the possibility that they might be related to minor earthquakes in the area. During the initial phase of the work, three seismographs were operated at widely separated stations, two in the region of coal mines at Coal Creek and Coleman and one at Turner Valley, distant from any mining operations. Some earthquakes were recorded at all three stations and, in addition, many small disturbances were recorded by the seismographs located near the mines, especially -by the instrument at Goal Greek. A closer network of radio-linked seismographs was then in-stalled near Fernie, the records of which definitely established that the small disturbances were occurring in the mine workings, both active and inactive. No relationship was established between bumps and local earth-quakes in the area. This work was initiated as a -co-operative effort with the Fuels Di-vision of the Mines Branch, Department of Mines and Technical Surveys, which has undertaken a study into the phenomena of ground stress relief in underground mine workings.

Jan 1, 1958

By d&apos, L. F. G. Assumpcao

Kaolin samples from Rio Capim resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the color removal process. Coating clays and delaminated clay were tested. Retention time (or pulp injection velocity), magnetic field intensity and matrix type were the&apos; variables studied. The feed brightness ranged from 84.7 to 87.6 % ISO for the coating clays and from 80.7 to 85.4 % ISO for the delaminated clay. The results showed unleached brightness values higher than 88 % ISO for coating products and higher than 87 % ISO for the delaminated product, using a conventional magnetic separator with an applied field of 1.5 to 2.0 Tesla. With a maximum field intensity in the superconducting machine of 5.0 Tesla, unleached brightness values higher than 88.5 % ISO for both coating and delaminated clays were attained.

Jan 1, 1995

By Martin J. Gavin

In an earlier paper (Karrick, Lewis, C. A convenient and reliable retort for assaying oil-shales for oil yield: Bureau of Mines, Reports of Investigations, Loral No. 2229, March, 1921. Reprinted in Eng. and Min. Jour, April 30, 1921, also in Mining & Met., May, 1921) which describes the apparatus and method used in the laboratories of the Bureau of times for assaying oil-shales, no mention is made of the quality of oil obtained when the apparatus is operated under conditions determined to be most suitable for producing highest yields of oils. So many inquiries regarding the nature of the oil have been received, that it seems advisable to present a short report on the subject. Experimental work indicates that it is possible to vary the quantity and quality of the oil obtainable with the assay retort from a given shale by varying the conditions of retorting. As an example, some figures that are averages for several closely agreeing tests are shown below.

Jan 1, 1921

By N. Nišić, A. Cvjetić, V. Jovanović, D. Knežević, D. Nišić

The risks associated with operating water reservoirs and tailings storage facilities (TSFs) are different because of their different purposes, methods of construction and operation, and characteristics of the materials impounded and their flow behaviour. Regardless of the differences, these two types of structures are often put in the same category when it comes to risk assessment and the application of relevant methodologies, which may result in unrealistic outcomes. In this paper we investigate whether it is possible to apply the risk ranking methodology designed for water reservoirs to TDFs and overview the key differences between these two types of structures. We also provide a comparative analysis of the results obtained by conducting a risk assessment of the operation of a TSF, applying the method recommended by the International Commission on Large Dams (ICOLD), and analyse the results using the failure mode and effects analysis (FMEA) technique. It is concluded that a more realistic evaluation of risk levels can be obtained by adopting a systematic approach to risk assessment in accordance with the traditional risk definition on which the FMEA technique is based.

Nov 30, 2022

By Y. Akin, M. Hancer, M. S. Celik, J. D. Miller

Flotation pulps with boron minerals such as colemanite and borax using primary amine collectors, e.g. dodecylamine, exhibit collector precipitation above a critical pH depending on the amine concentration. This was earlier attributed to the formation of a mine hydroborate. However, results from this current study indicate that the precipitate is dode-cylamine, rather than dodecylamine hydroborate. A systematic study involving solubility, zeta potential, microflotation, adsorption, and surface tension measurements is presented to elucidate the role of a mine precipitates in boron flotation systems.

Jan 1, 2000

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack &apos;of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

[Participating Scholarship Colleges and Universities 136 Big Sky Coal Company 111 Canyon Fuel Company LLC 97 Coal Age Magazine 109 Commercial Testing & Eng. Co 99 Continental Conveyor & Equip. Co 103 Copper Mountain Resort 128 Dakota Coal Co 100 DBT America Inc 117 Empire Machinery 101 Energy West Mining Co 102]

Jan 1, 2001

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021