Search Documents

By E. W. Dean

A previous report of the Bureau of Mines* has supplied data for the physical and chemical properties of samples of crude petroleum produced in the eastern fields of the United States. It was issued as a preliminary chapter of a bulletin which is to cover the results of a survey of the entire country. The present report is a second preliminary chapter including figures that are available for the producing fields of the Rocky Mountain district. Work is being continued. with a series of samples from the States of Kansas and Oklahoma which will be described in a third preliminary chapter, to appear at a subsequent date. Acknowledgments. The obtaining of samples was rendered possible through the courtesy of representatives of a number of producing and refining companies operating in the Rocky Mountain district. The Bureau hereby acknowledges its appreciation of the hearty spirit of cooperation that was universally encountered.

Jan 1, 1921

By L. A. Haas

Hydrogen sulfide was decomposed to elemental sulfur in an electrical discharge. With He, N., or Ar diluents, a threshold voltage between 1 and 3 kV was required for the decomposition reaction to occur in a laboratory ozonizer. Above the threshold voltage, the HAS decomposition rate increased with increasing voltage, but the increase was more pronounced with argon diluent than with either nitrogen or helium. In common with other reactions in an electrical discharge, the B2S decomposition decreased with increasing temperature in the range of -410 to +61° C. The reaction did not appear to be rate-controlled by a solid-gas sorption step because the introduction of activated charcoal into the electrical discharge zone did not significantly affect the decomposition yield. In the presence of polymeric chlorofluoro-carbon oil, 90 pct conversion of the 3 pct H2S in helium was obtained at 14 kV, 60 Hz, a 2-mm electrode gap, and a gas-residence time greater than 1 min. Under the same experimental conditions in the absence of oil, the conversion was only about 50 pct.

Jan 1, 1973

By S. Oppenheimer, P. Au, R. M. Kearsey, J. Tsang, E. McDevitt

A new superalloy, ATI 718Plus® Alloy (718Plus), has been developed to have a 55oC higher temperature capability over the traditionally used Alloy 718, while maintaining favourable processing characteristics and intrinsic raw material costs. The fatigue and dwell-fatigue behaviour of four microstructural variations of 718Plus are evaluated and compared to Waspaloy: 1) standard heat treated condition (HT1), 2) standard heat treated condition with thermal exposure at 732ºC (1350ºF) for 1000 hours (HT2), 3) fine grain condition with a modified d phase (HT3), and 4) fine grain overaged through modified heat treatment (HT4). The results show that the steady-state fatigue crack growth rates of each microstructural variation and both alloys are identical, with all of the 718Plus variations showing a clear advantage over Waspaloy in the fatigue crack threshold regime. Dwell-fatigue results show that Waspaloy has better resistance to crack propagation under dwell conditions; however, optimization of the precipitate phase shows vast improvement in the dwell-fatigue resistance of 718Plus.

Jan 1, 2010

By Yi Luo, FENGLIANG WU

Explosions and fires originated from longwall gob due to the formation of methane-air mixture have been a severe threat to coal miner’s lives.Many numerical studies on coalmine fire and explosion hazards have focused on the airflow in roadways and mine gobs. However, most of these studies isolate the gob from its surrounding roadways, and the network analysis and the CFD method are applied independently tomodel the two classes of airflows. This approach greatly limits the ability of simulatingmine ventilation flow, especially unable to consider the effects of gob boundary conditions on air exchange between the gob and the surrounding airways. An innovative finite tube method (FTM) is developed to couple the one-dimensional mine ventilation network (MVN) and the 2D/3D gob flow field (GFF). In FTM, GFF is discretized into a finite number of flow tubes each of which is formed by any two adjacent stream lines. These tubes, representing the gob’s field flow, connect the MVN into a new coupling network. To solve the coupling model betweenMVN and GFF, an iterative solution technique is developed inwhich the MVN analysis is used to evaluate the boundary pressures for GFF simulation and in turn the FTM feeds the GFF results back to the coupling network. Based on the FTM approach, a model for gas migration in gob has been established for delineating the hazard zones of explosive methane concentration and spontaneous combustion. A computer program is developed to implement the FTM simulation. An illustrative example with five flow tubes representing the GFF is created to verify the stability and convergence of the FTM solution process. A simulation example also indicates that the accuracy of FTM is improved by 12% compared with previous method. Results of an application case show that the program is capable of quantitatively evaluating the gob’s risk zones prone for spontaneous combustion and gas explosion as well as performing risk analysis for various ventilation scenarios.

Jul 10, 2020

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010

By M. F. Goudge

ROCK wool, one of the most recent additions to the list of Canadian-made, insulating materials, is a soft, light, fibrous material consisting of interlaced, flexible, glassy fibres so exceedingly fine that, individually, they are almost invisible to the naked eye and will float in air. In the process of manufacture, a suitable rock, generally a self-fluxing argillaceous dolomite consisting of nearly equal proportions of acidic and basic constituents, is melted to a completely fluid state and then converted into fibres either by a blast of steam or air, or by a mechanical device. The increase within the past five years in the number of plants in the United States making rock wool and slag wool has been remarkable, especially in view of the depressed conditions prevailing 'with most industries during this period. In 1930, there were only 8 plants reporting production of .these materials, whereas at the present time there are 44 plants in the United States listed as making these products, and there are 3 plants in Canada. In 1929, the total sales of rock-wool products in the United States amounted to-$2,377,324. In 1934, according to the National Rock and Slag Wool Association, 26 member companies reported sales of $3,695,405, and in 1935 the sale's of 30 member companies had a value of $5,571,469. The establishment of the rock-wool industry in Canada followed the publication in 1931 of a report (1) by the Mines Branch, Department of Mines, Ottawa, in which was set forth the results of field work and laboratory studies which indicated that large deposits of rock in the Niagara peninsula, hitherto regarded as valueless, were suitable for the making of rock wool. This report was supplemented in 1934 by another report (2), giving the results of further laboratory and commercial-scale tests on the rock from these particular deposits, which proved conclusively that rock wool of good quality could be made from the rock in question.

Jan 1, 1936

By Paul Guliov

Industrial clays, including a variety of bentonites and kaolinbased clays in southern Saskatchewan are hosted by Late Cretaceous and Early Tertiary sediments. Ofparticular significance are the deposits of swelling bentonite in the Cretaceous Bearpaw Formation and the kaolinitic clays of the Cretaceous Whitemud and Paleocene Ravenscrag Formations. Swelling bentonite is currently produced in the Wilcox-Truax area by Canadian Clay Products Inc. and yields at least seven different commercial products for a variety of applications. Kaolinitic plastic clays, including ball clay, stoneware and earthenware clay, as well as kaolin in southern Saskatchewan, have a long history of development and use. Products include common and face brick, refractory bricks and other shapes, chinaware, pottery, sewer pipe, chimney flue linings and tiles. Currently clay production is for out-of-province brick manufacturing and for pottery. Recent research and improved technology combined with expansion in certain areas of the global clay industry generally hold promise for a resurgence of a clay-based industry in Saskatchewan. Products of particular promise include: clay tiles; kaolin fillers and extenders; and aluminum as well as related by-products from kaolinitic clays based on the carbochlorination process.

Jan 1, 2001

By Wm. W. Odell

A study of certain gas making and fuel problems peculiar to the gas industry of California has been made by the Bureau of Mines. The work was done at the request of, and in cooperation with The California Gas Research Council 2, for the purpose of obtaining basic information on the gas-making fuels available to California, and their applicability to the present and future needs of the gas industry in that State. The data obtained have been applied in outlining a construction program, and indicate the possibilities in efficiently utilizing fuels in making gas by other than the oil-gas process. This paper presents an outline of the study and a summary of the principal results obtained, with some of the more important conclusions and recommendations based on this data. Gas is produced in California by processes which are both unique and different from those common to other parts of the United States. The bulk of the manufactured gas is made in and distributed from two main districts which are centers of population - namely, the Los Angeles district and the San Francisco Bay district. The gas manufactured in the Bay district is, almost exclusively oil-gas, whereas that produced in the southern part of the State, where natural gas is available, is mostly mixed natural gas and reformed-gas, but oil-gas is the chief product when the supply of natural gas is inadequate. Practically all of the gas companies are equipped with oil-gas generating apparatus, and anticipate using it in the future. As the continued use of the oil-gas process to the exclusion of all other processes, depends upon a continued supply of oil at a low cost, and the prospect of obtaining such low-priced oil in the future is somewhat uncertain, the questions have arisen: What will the future gas-making process or processes be? When will it be necessary to make plans for the installation of different gas generating equipment, and what will that equipment comprise?

Jan 1, 1926

By V. B. Dale

This is one of a series of reports covering the mineral resources of the Nation. It describes briefly most of the known tungsten deposits in Yuma, Maricopa, Pinal, and Graham Counties, Ariz. Most of those described were examined by the author. An effort was made to determine the position of the various deposits by section, township, and range and to give accurate road direction to each property from a prominent landmark. All available maps have been used in making these determinations, but in unsurveyed areas it was necessary to make approximate projections of subdivisions. The township and range numbers refer to the Gila and Salt River base and meridian.

Jan 1, 1959

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni, 16 per cent Cr, 35 per cent Ni, 12 per cent Cr, 60 per cent Ni, etc ) in recent years has been accompanied by continued demands by the consumer for improvement in properties The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper† The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure The creep-test laboratory constructed for the American Brake Shoe and Foundry Co is designed to permit 1000-hr tests in the temperature range of 1200° to 2200°F with a choice of applied stress extending from 50 to 50,000 lb per sq in in increments of 50 lb per sq in To simplify the calculation of weight combinations, the loading beams (Fig I) are provided with counterweights to eliminate the tare The precision of the knife-edges (10 1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle Check of the loading weights proved the maximum error to be 0 06 per cent Axial alignment is provided by crossed knife-edges in the grip seats The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U S Steel Corporation An 80 per cent Pt, 20 per cent Rh No 19 B and S gauge wire is used as the heating element The details of construction are shown in the radiograph reproduced in Fig 2 The windings are held in place on an alundum tube with alundum cement, the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F over a 4-in gauge length (Fig 3) To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By J. V. Gluck

In the present paper," as in earlier publications, V1&apos;2"1 the authors present experimentally obtained relations for the free energy of solution of oxygen in various metals as a function of temperature. The relations are linear and given in slope-intercept form. The authors give values for the "probable error" of the slope and intercept, citing Birge&apos;s method17 for obtaining these quantities. Birge discussed these methods as early as the period 1929-32.25726 In Ref. 25 the probable error is defined as "the numerical value which the true error is as likely to exceed as not", i.e., 50 pct probability. Ref. 26 is even more detailed and includes a lengthy discussion of the applicability of the Gaussian distribution to experimental data. However, the use of the "probable error" has come under some question. For example, Ezekiel&apos;~ states that "the use of the probable error tends to make the results appear rather more accurate than the standard error". Moroney28 stated (in 1951) that "the term &apos;probable error&apos; was used in former times to denote 0.67450 (50 pct confidence using the normal distribution)....the term, a poor one, is now very much obsolescent. It has been said that &apos;it is neither an error nor probable&apos; ". Bennett and Franklin in 1954" in discussing statistical confidence levels mentioned that "the customary use of the 5 and 1 pct levels is not completely a matter of chance; these levels probably represent a balance between the desire to be correct and the desire to be specific. Also in most people&apos;s minds the borderline between something that could possibly happen and something that is not likely to happen is somewhere in this region. Certainly 5 or 1 pct confidence limits are to be preferred to limits such as the &apos;probable error&apos; which has only a 50/50 chance of including the correct value." It may readily be seen that the 95 pct confidence level, which is given by 1.960 (assuming large sample size), thus corresponds to approximately three times the "probable error". Indeed, limits of one standard deviation correspond only to about 68 pct probability. Even if we triple the tolerances given by the authors in the equations of their Table 111, the deviations do not become excessive and would not detract from their excellent results. It could then be said with a high degree of confidence (95%) that the precision of the slope and intercept values is about *3-5 percent of their absolute levels rather than the 1-2 percent implied in Table 111. This is then compatible with an earlier suggestion of Gokcen~&apos; of a probable accuracy of 5 pct in dissolved oxygen measurements by the technique employed. Alternatively, the authors could have

Jan 1, 1967

By Ronald S. Conti

The Bureau of Mines conducted a comprehensive laboratory study of the thermal ignitability of various carbonaceous dust clouds with particular emphasis on various ranks of coal dust. The tests were conducted using a new 1.2-L furnace. Autoignition temperatures of dust clouds were obtained as a function of coal volatility and particle size. Dust particles and gas samples were collected by a rapid-sampling system in order to study the reactions involved in preignition and postignition processes. The autoignition temperatures measured in the new 1.2-L furnace were significantly lower and therefore more conservative than those measured previously in the Godbert-Greenwald furnace. The combined effects of thermal and electrical ignition of dust clouds were also studied in the 1.2-L furnace using electrical discharges of varying energies at ambient and elevated temperatures. The minimum spark energy necessary to ignite a dust cloud decreased significantly as the temperature of the dust cloud increased.

Jan 1, 1983

Jan 1, 2004

By M. M. Neale

The pottery department has been aptly described as the "heart of the zinc plant," md every operator of a horizontal-retort plant is acquainted with the fact that good retort practice is the keystone of the smelting process. Since retorts and condensers are clay products, it is obvious that improvements in other branches of the ceramic industry should be observed for possible adoption in the pottery process for zinc smelting. Deaeration of clay bodies is one of the improvements that have become fully, established in many brick and pottery plants. Our investigation of a number of these installations always yielded the same answer—improved practice. Improvement in workability, elimination of laminations, less porosity, greater wet and dry strength, were among the claims put forth for this process. All of these features are exceedingly desirable characteristics in the manufacture of a zinc retort. A preliminary test, which involved truck transportation of deaired slugs over a relatively long distance, did show the value of many of these characteristics in forming the retort. Results from the standpoint of , longer retort life in the smelting furnace were not outstanding. The idea lay dormant for several years but was revived again in 1940, when it was decided to make whatever changes were necessary in the equipment for pottery manufacture to fully demonstrate the process. A number of the manu- facturers of machinery for clay work were asked to submit proposals, and the plan finally adopted was extremely simple and economical. Machine FOR DeaeRRATING Selection of the &apos;&apos;Straight-line&apos;&apos; principle for conversion of the "Wettengel" pug mill to a &apos;&apos;vacuum-extrusion" machine preserved some usable parts of the original equipment, such as the drive mechanism, and main shaft. The converted machine consists of a feed hopper, a compression and shredding zone, a vacuum chamber, and an extrusion barrel, as shown in Fig. I. In operation the clay mix travels from the feed hopper into the compression zone, where it is compressed and finally forced around the tapered cone into the vacuum chamber. As it enters this chamber the clay body is shredded into thin plates, for exFosure to the vacuum. The shredder consists of a hub mounted on the main shaft, to which are bolted segmental sections, each of which carries shredder knives. The compression zone and extrusion barrel function as seals for the vacuum chamber and the shredded clay mix is agitated thoroughly during its exposure to the vacuum. A vacuum pump, equipped with a 3-hp. motor, is attached to this chamber, and maintains 25 to 26 in. vacuum during operation of the mill. Changes in Practice Prior to the adoption of the deaeration process, our standard pottery practice called for double mixing in the combination 7

Jan 1, 1944

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts&apos; Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts&apos; method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts&apos; law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,&apos;4, &apos;6 Fe-Cu,&apos;6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 &apos;77 187 19>2° Fe-Sn,16 and Fe-v.51 &apos;3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961

By André Chagnon, Yvon Héroux

"Résumé - Cette étude porte sur l&apos;altération de la matière organique et des argiles dans les boues carbonatés dévoniennes du faciès ""F"" de la Formation de Pine Point et ses équivalents stratigraphiques la Formation d&apos;Evie et l&apos;unité bitumineuse de la base de la Formation de Horn River. La matière organique se compose principalement de bitume solide et de quelques fragments de fossiles (organo­ clastes). La majorité des échantillons ne renferment que de l&apos;illite et des interstratifiées illite/smectite.Si on compare les températures d&apos;homogénéïsation (Th = l00°C) des inclusions fluides de la sphalérite et des dolomites associées à la minéralisation aux températures estimées à partir de la réflec­ tance de la collinite (84°C à ll7°C), l&apos;on ne peut pas conclure à la présence d&apos;une anomalie ther­ mique dans le district minier de Pine Point. De plus, la réflectance des organoclastes n&apos;est pas plus élevée dans le district minier de Pine Point que dans les localités plus éloignées des gîtes. L&apos;analyse des minéraux argileux conduit à la même conclusion : aucune anomalie thermique n&apos;est décelable dans les unités échantillonnées à l&apos;intérieur du district minier de Pine Point quelque soit l&apos;indicateur utilisé.La kaolinite et la matière organique altérée, affichant des valeurs anomales de sa réflectance, se trouve essentiellement en présence de soufre et de sulfures. Cela suggère une origine authigène de la kaolinite et une altération de la matière organique reliées au phénomènes de minéralisation.Abstract- The alteration of organic matter and clays is studied in the Devonian Pine Point Formation carbonate muds, ""F"" facies, and its lateral equivalents the Evie Formation and the biturninous unit at the base of the Horn River Formation. The organic matter is mainly composed of solid bitumen with few fossil fragments (organoclasts). Most samples contain only illite and mixed layer illite/smectite.If we compare the Th(l00°C) from fluid inclusions of sphalerite and dolomites associated with mineralization to the temperatures calculated from the reflectanœ (Ro) of the collinite (84°C to 117°C), we cannot detect a thermal anomaly in the Pine Point mining district. This result is based on the reflectance values of organoclasts from the mining district that are not higher than those reflectance values measured on organic matter (OM) away from the ore deposit. A similar conclusion is reached from the clay study: none of the parameters used allow us to identify a thermal anomaly in the samples from the mining district.The kaolinite and the altered OM showing anomalous Ro values mainly occur with sulfides and sulfur. This association suggests an authigenic origin for the kaolinite and an alteration of the OM due to the mineralization events."

Jan 1, 1994

By Xin Wang, He Shao, Wenpu Li, Yiyi Zheng, Xi Chen, Yurong Gao

This study utilized experimental and numerical simulation methods to investigate and analyze the atomization characteristics of three internal air–water mixed atomizers under different operating conditions. By comparing the research results, the effective dust control working parameters for the application of the selected atomizer in the engineering field were determined. Firstly, the atomization characteristics of the three atomizers were studied using a customized experimental system. The results indicated that nozzle 2 had a wide atomization range, a small atomization distance, and small droplet size; nozzle 3 had a narrow atomization range, large droplet size, and fast atomization speed; and nozzle 1 not only had a large atomization range but also could produce droplets of dry mist size with fast atomization speed, meeting the dust reduction requirements of the Majiliang Coal Preparation Plant. Secondly, Fluent software was used to simulate the atomization process and particle size distribution of the three internal mixed atomizers, determining the working conditions of the atomizers, the required number of atomizers, and the application angle of the atomizers in the internal mixed dust removal system. Finally, the atomized dust control system was applied on-site, achieving a total dust removal efficiency of 90.72% and a respirable dust removal efficiency of 89.75%.

Mar 9, 2024

By Lluis F. Fontboté

The paper point out the deposits about the carbonate-hosted San Gregorio Colquijirca, as products of an epithermal high sulfidation system. Field, geochemical, and geochronological evidences suggest that the different ore types of the Colquijirca District are caused by a pulsed high sulfidation system subsequent to the emplacement of a diatreme volcanic complex. The first stage formed disseminated Au±Ag mineralization in areas affected by vuggy quartz alteration at Marcapunta. During a second stage, base metal mineralization replaced Eocene carbonate sediments from the Marcapunta diatreme to 2.5 km more to the north. San Gregorio and Colquijirca are to our knowledge the first "carbonate-hosted epithermal Zn-Pb high sulfidation deposit" recognized as such. The correct recognition of this ore type opens new exploration possibilities for base metal in high sulfidation systems affecting carbonate rocks.

Apr 24, 2001

By S Brochot

During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material coming from a selection of various drilling products or a sample coming from a mining test. This sample can represent several tonnes of material which are analysed and split to be used in various tests.In the current case, a composite sample is dedicated to semi-autogenous grinding (SAG) pilot plant tests. The property of interest is then the size distribution of the material. The sample is mixed and a subsample is taken to measure the size distribution which is considered as the feed size distribution. Then the remaining material of the sample is divided in several subsamples for batch grinding tests at different operating conditions. The product of each grinding test is then analysed to measure its size distribution.The grinding performances are analysed at the light of the measured size distributions for feed and product. But what is the accuracy of the measurement of these size distributions? What is the variability of the feed knowing each feed is just a subsample of the initial sample?The Pierre Gy theory of sampling answers these questions.The current paper presents, through a real example, the calculation of the measurement error of the size distributions and the variability of the feed between the different tests. The uncertainties of the grinding performances are then calculated and their impact on the results interpretation is then analysed.CITATION:Brochot, S, 2012. Sampling for grinding pilot plant test - the effect of size distribution variability, in Proceedings Sampling 2012 , pp 127-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012