Search Documents

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By William W. Edgerton, Moussa Wone, David H. Corkum, Carlton M. Ray

"The DC Clean Rivers (DCCR) Project is a 25 year, $2.6 Billion court ordered project to reduce combined sewer overflows (CSOs) discharging into the Potomac and Anacostia Rivers and Rock Creek, and also reduce flooding in the northern areas of the District of Columbia. Like all massive infrastructure programs, DCCR faced technical challenges, management challenges, risks of cost and schedule overruns, procurement challenges, and financing challenges. While DC Water is no stranger to large capital improvement projects (CIP), this CSO Program represents a once in a lifetime event for the Owner requiring the assembly of a single purpose team to implement. Some of the DCCR Project team’s most successful accomplishments to date are attributable to its introduction of early contractor involvement (ECI) to thoroughly vet the work from the perspective of the future constructors, development of functional baselines to share risks that are difficult to price and reduce reliance on geotechnical baseline interpretation during tunnel excavation, and attainment of financing through Municipal Century Green Bonds based on using design criteria of a minimum of 100 year life for the structures to establish intergenerational equity and fairness. This paper will discuss these innovations in detail and provide some sets of recommendations for the underground industry on when and how to use different approaches to better manage projects of this magnitude. INTRODUCTION The District of Columbia Water and Sewer Authority (DC Water) is an independent multi-jurisdictional authority that was established in 1996. Its primary mission is to provide water distribution services to more than 640,000 residents in the District of Columbia (District), and sewer treatment and disposal to 1.6 million residents of the District, Montgomery and Prince George’s counties in Maryland and Fairfax and Loudoun counties in Virginia."

Jan 1, 2016

By Henry H. Ginsberg

The effectiveness of 0.01 pct. molybdenum, as ammonium molybdate impregnated on coal, on the hydrogenation of a high-volatile bituminous C coal at 8,000 p.s.i.g. and 460° to 480° C. has been studied in a pilot plant by the Federal Bureau of Mines. Under these conditions, the Bureau obtained 98 to 99 pct. conversion5/ of coal to liquids and gases at throughputs of 29 to 101 lb. of m.a.f. coal per cubic foot of reaction space per hour. At 460° C. the indicated yield of oil ranged from 63 pct. (based on m.a.f. coal) at a throughput of 35 lb./c.f.h. (pounds per cubic foot per hour) to 68.5 pct. at a throughput of 58 lb./c.f.h., and the yield of gaseous hydro-carbons ranged from 25.5 to 19 pct. at the same throughputs. The maximum measured yield of oil boiling under 325° C. was 47 pct.

Jan 1, 1960

By Donald E. Zipperian

The studies described in this paper have established that flotation conducted in a column cell provided with gas generation by aspiration into surface tension lowered water, may considerably increase the efficiency and particle size range of a flotation process. Operation of a DEISTER FLOTAIRE ® Cell at several Southwest United States flotation plants under continuous rougher, scavenger and cleaner conditions has demonstrated the main positive features to be: (a) higher capacity per unit volume than conventional flotation equipment, (b) improvement of flotation of plus 0.210 m particles, (c) improved flotation of particles minus 0.037 m.

Jan 1, 1984

By Fujio Ishii

The deoxidation of liquid nickel and nickel binary alloys with silicon has been determined at temperatures between 1500°C and 1650°C using quartz crucibles in order to investigate the deoxidation of nickel based alloys. The equilibrium constant of the deoxidation reaction in liquid nickel and the effects of the different alloying elements such as chromium, molybdenum, tungsten, iron, cobalt and coppcr on the activity coefficient of oxygen in liquid nickel have been established.

Jan 1, 1993

By Holt. Grover J.

"IntroductionThe history of iron ore production in the United States has followed a pattern not far different from that set in the production of non-ferrous ores; the first interest of the prospector and miner being the discovery and development of high-grade ores. In the early stages of development of most mining districts, high-cost low-grade ores are usually of slight interest due to the additional capital investment required in concentrating plants, as well as the increased requirements of •power and other facilities. As the reserves of higher grade ores are depleted and the technical knowledge of ore beneficiation is broadened, production of concentrates from the lower grade ores is stimulated.The real stimulus necessary to arouse serious consideration of beneficiated iron ore in the Lake Superior district has been provided by the serious inroads made in the high-grade ore reserves by two World Wars.The first shipment of high-grade iron ore from the Mesabi range in Minnesota was recorded in 1892, and the first token shipment of concentrates was made 15 years later, in 1907. Not until 1910 did the production of concentrates assume any great importance. A steady increase in concentrate production over the years is shown by the fact that, in 1910, concentrates accounted for 8 per cent of the total shipments from the State, whereas by the time of World War II this percentage had increased to 22 per cent and by 1948 had risen to 26 per cent. It seems a safe assumption that the shipment of concentrated iron ore, from the Mesabi range in particular, will continue to increase even more rapidly from now on, with other iron ranges of the Lake Superior district following this lead."

Jan 1, 1950

By Kenneth R. Krivanek

In recent years the widespread problems of air and water pollution generated by both population and industrial expansion have become a major public concern. Therefore, many municipalities are striving to achieve more efficient wastewater treatment processes so these wastewater's can be reintroduced into the waterways of our nation with little or no detrimental effects on the future beneficial use of that water. With this, improved treatment comes an ever increasing volume of wastewater sludge which must be disposed of in a manner of minimal impact on the environment. Furthermore, with demand for energy continually accelerating in this nation, our concern over high oil prices and our increasing dependency on foreign oil sources, there has been an ever growing interest in the largest energy source that are nation has, coal. However, surface mining of coal can cause many environmental problems when adequate precautions are not faithfully adhered to. These problems include water pollution from silt and/or clay erosion and acid runoff, produced by oxidation and hydrolysis of pyrite; i.e., FeS2 + 3/02 + H20 + FeSO4 + H2SO4. One method of wastewater sludge disposal which can utilize large volumes of sludge for a beneficial project that may not compound our environmental problems is spray irrigation, to either depleted farmland or to abandoned strip-mined soils. Sludge is characteristically high in organics, as well as having near neutral to alkaline pH properties. With these two qualities it possesses a potential for neutralizing acid strip mine spoils, which would enhance the establishment of a vegetative ground cover. Sludge can accomplish this by lowering the oxidation potential, reducing the solubility of iron and aluminum and by the chelation of metals, thereby

Jan 1, 1977

By L. B. Berger, W. P. Yant, J. B. Littlefield

"INTRODUCTION Hydrogen sulphide (H2S) is one of the most toxic industrial gases and of relatively wide occurrence in industry. Among its common industrial occurrences are, in the production and refining of high-sulphur petroleum, in natural gases, in gypsum and sulphur mining, in rock strata and underground waters (where it is encountered in tunneling and caisson work) in blasting with black powder and in blasting high-sulphide ores with other explosives, in gas manufacture, in the carbonization of coal, and in the manufacture of chemicals.The usual methods of detection, other than by the sense of smell, which is lost in 2 to 15 minutes' exposure to 0.010. to 0.015 percent of this gas, 5/ either are too cumbersome for frequent and rapid analyses or, like the wet lead acetate paper test, afford only qualitative results. A qaantitative determination usually involves the use of solutions, bubblers, flowmeters, standard solutions, burettes, and indicators manipulated by trained technical men. All apparatus and methods in common laboratory use are, in general, unsuitable for the field.The physiological response attending exposure to various Concentrations of hydrogen sulphide in air, is as follows, in percent by volume 6/:0.005 to 0.010: Subacute poisoning - slight symptoms, such as mild conjunctivitis and respiratory-tract irritation after 1-hour exposure."

Jun 1, 1935

By T. A. Hendrickson

The Bohemia district, situated about 30 miles southeast of Cottage Grove, Oreg., in the Calapooia Range, has been the major producer of lead and zinc in Oregon. Sporadic production has been Maintained from the district since its early discovery about 1858. In 1942, a selective-flotation mill was built at the Champien mine, which operated for only a short time and was forced to close because of the war and lack of labor. The Champion mill reportedly has been operated as a custom mill for the treatment of ore from the Musick and Helena mines, located in the district sometime in the past. This report summarizes the results of laboratory ore-dressing studies made on ore samples from the Musick and Helena Mines.

Jan 1, 1951

1.Assessment of methane content in coal. Given a naturally low methane content in 11 Coal Seam and the fact that the areas of the 11 Seam adjacent to the tunnelway were degassing for a very, very long time due to previous development and mining, it is conservatively estimated that the remaining in -situ methane is less than 0.5m3/tonne. 2. Continuous miner cutting rate based on the past practice. The best loading rate recorded at the past operations of Smoky River Coal was 45 seconds for a 8 tonnes shuttle car. Using these records, the maximum peak loading rate potential at the face is calculated at 0.178 tonnes per one second or 10.67 tonnes per one minute. 3. Methane release at the face. ?The actual face methane liberation, conservatively assumed at 40% of the total in situ content: 0.20 m3/tonne ?The peak cutting rate: 0.178 t/sec ?The maximum (peak) face methane release: 0.20*0.178 = 0.036 m3/sec

May 1, 2003

By K. O. Bennington

The thermodynamic properties of two manganese silicates, pyroxmangite and fowlerite (zincian rhodonite), were experimentally determined by the Bureau of Mines. The standard enthalpies of formation were determined by hydrofluoric acid (HF) solution calorimetry, the low-temperature heat capacities by adiabatic calorimetry, and the high-temperature heat capacities by differential scanning calorimetry over the range 322 to 1,372 K. Data for the standard enthalpy of formation (AH298), the derived standard entropy (S298), and the standard Gibbs energy of formation (AGf 298) are as follows: Pyroxmangite [(Mn0.9554Cao,0446)(Si03)J- AHf298 319.668±0.46 kcal/mol AH298 (from oxides)... -7.215±0.11 kcal/mol 5295 23.785±0.048 cal/(mol'K) AGf298 -301.190±7.96 kcal/mol Fowlerite [(Mno.7o3Zno.0884Ca0.2086)(Sio3)]--AHf298 ?... -329.914±0.419 kcal/mol AH298 (from oxides)... -8.400±0.104 kcal/mol 5598 21.949±0.059 cal/(mol-K) AGf298 -310.716±7.99 kcal/mol These experimentally determined values were combined with data from the literature to calculate the Gibbs energies and equilibrium constants of formation over the temperature range of the measurements. Standard enthalpies, Gibbs energies, and equilibrium constants of formation are given as a function of temperature from both the elements and the constituent oxides.

Jan 1, 1987

By Albert Ruiz

The 2,250-MW, coal-fired Navajo Generating Station located in Page, AZ draws water from Lake Powell using submersible pumps installed in five inclined shafts. Drought threatens to lower the reservoir to below the existing intakes. A system of new steel-lined intake shafts located on the same site was required for uninterrupted plant operation. The small size of the site, and the need to keep the existing system in operation, required detailed designs and placed significant limitations on construction equipment and activities. The Navajo Sandstone that forms the near vertical shoreline of the reservoir is 98 percent very fine grained quartz, highly abrasive and contains highly fractured intervals that presented numerous challenges to drilling the new 152-m (500-ft) deep, 109-cm (43-in.) diameter intake shafts inclined 23° to 26° from vertical. Spatial constraints, submersible pump design and operational criteria required that each shaft have a unique inclination and orientation and hit a small breakout target located 76 m (250 ft) under water. Sophisticated drilling equipment and techniques as well as state of the practice downhole survey technology and methods were used to make adjustments and maintain drilling accuracy with less than 1 percent deviation. Environmental requirements mandated water as the drilling fluid and grout was not allowed in to the lake under any circumstances. The shafts were videotaped and the breakout locations were examined using an underwater remotely operated vehicle (ROV) to verify shaft locations and rock conditions, and to guide placement of pneumatic packers to ensure grout did not transmit to the lake during the steel liner installation. In anticipation of the invasion of quagga mussels, the shaft design included an allowance for a chemical dosing system and a copper-rich alloy at the exposed portions of the steel liner.

Jan 1, 2011

By James F. Neill, O&apos

Investigation of the Gilley fluorite deposit was based upon examinations made by several of the Bureau's mining engineers. Fluorspar was found in the dump talus of sloughed and water-filled trenches and shafts, and there were indications that faulting or other dynamic distortions favorable to deposition of this mineral in minable quality and quantity might exist. The inference was based upon a field study of the area and its comparison with fluorspar deposits in Kentucky. The proximity of this deposit to the iron furnaces at Gadsden and Birmingham was a factor that influenced its investigation, as the demand for metallurgical grades of this critical mineral is acute. The present supply for the district is obtained from out-of-State sources, and the value of any local deposit would be enhanced by the saving in freight charges. The Gilley fluorspar deposit is 17 miles east of Gadsden and 50 miles northeast of Birmingham, Ala. Mineral deposits occur as thin veinlets and small bunches of fluorite in upturned bode of siliceous limestone. The ore-bearing structure is a reverse fold, and the mineral deposit appears as a replacement along crumbled zone fractures of the contorted limestone.

Jan 1, 1950

By Oliver Bowles

The term" sandstone" is applied to a rock composed of mineral grains smaller than pebbles, cemented together more or less firmly. "Conglomerate" is the name given to a rock composed of pebbles, or pebbles and bowlders, of various sizes cemented together. If the pebbles are large and well rounded the rock is sometimes called " pudding stone." Although the term "sandstone" includes all varieties, certain specific terms are applied to types characterized by particular compositions, colors, or uses. "Quartzite" is a variety in which the individual grains are so firmly cemented together with quartz that the rock will fracture as easily through the grains as through the cement; "ferruginous sandstone" is one rich in iron as cementing material, or as grains, or both; "micaceous sandstone" is one in which mica is prominent; " arkose" is a feldspathic or granitic sandstone composed of angular grains; "calcareous sandstone" is one containing considerable calcium carbonate; and" argillaceous sandstone" is one containing considerable clay. The term "flagstone" is used for a rock that splits readily into sheets suitable for flagging; "freestone" for rock than can be cut or carved readily, and with equal ease in all directions; and" ganistel'," in the United States, for sandstone suitable for the manufacture of refractories. Others are named from their characteristic colors such as " bluestone," " redstone," or " brownstone."

Jan 1, 1917

By Steven A. Fechner

The U.S, Bureau of Mines is conducting a four-year (1987-1990) study to assess the mineral resources and mineral development potential of the Valdez Creek Mining District in southcentral Alaska. This study is part of the Bureau's ongoing statewide mining district evaluation program. This report summarizes the Bureau's site specific evaluations of two areas (Tyone and Peters Creek) of the district that were investigated to determine the bedrock sources of gold and PCM in the alluvial gravel of both areas. In the Tyone Creek area, grains of gold (up to 0.0212 oz/yd3) and platinum group minerals (PCM) were recovered from alluvium and weathered conglomerate of the Jurassic Naknek Formation and Tertiary age using placer sampling techniques, Platinum and palladium were detected in the heavy mineral concentrates recovered from placer sampling the alluvium, and Naknek Formation and Tertiary conglomerates. In the Peters Creek area, grains of gold (up to 0.014 oz/yd3) were recovered from the alluvium and Tertiary Sterling Formation conglomerate. The Bureau's evaluations indicated that drainage basins containing conglomerate are the most favorable targets for placer gold and PGM exploration; and Tertiary conglomerate represents a high volume, low grade gold resource.

Jan 1, 2011

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By John R. Goode

"This paper reviews options for the separation of a mixture of rare earth elements (REE) into its component elements. Earlier separations used selective chemistry such as double salt precipitation and reductive/oxidative processes – methods that still have a place in the industry. Fractional crystallization was developed for more complete separations of adjacent REE. The latter method was replaced by ion exchange (IX), which was in turn replaced by solvent extraction (SX). Two main SX chemistries are in use, solvation and cation exchangers, with several variants (mixed solvents, ionic liquids, etc.) now under investigation. SX plant configurations have evolved including advanced techniques like “hyperlinking”, novel saponification methods, and alternative stripping techniques. The classic mixer-settler is the most commonly employed device although centrifugal contactors have been pilot-tested. Non-dispersive SX options including microfluidic devices and membrane-assisted SX techniques are being developed and could revolutionize the SX option. Other REE separation techniques now being studied include Molecular Recognition Technology (MRT), Free Flow Electrophoresis (FFE), newer IX systems, and electrolytic processes. Additionally, the classical crystallization and selective precipitation methods and newer bacteria-mediated processes, chloride volatilization, high performance liquid chromatography, and magnetic separation systems have been studied. This paper reviews the options and concludes that conventional SX is the technology of choice but viable alternatives could be demonstrated and acceptable within a couple of years.INTRODUCTIONThe chemical properties of the individual REE are very similar which is why REE minerals and ore deposits almost invariably contain a mixture of all fifteen REE, i.e., La to Lu plus Y. That said, the distribution of REE in a given deposit is frequently dominated by the light REE (LREE, i.e., La to Nd). Examples include the Bayan Obo, Mianning, Lynas Mt. Weld, and Molycorp Mountain Pass deposits where heavy REE (HREE – Sm to Lu and Y) typically account for well under 5% of the REE content. The LREE operations produce some HREE but the main sources of these important elements are the ionic clay deposits of Southern China. Importantly, all of the REE recovery operations referenced above, except for cerianite-bearing ionic clay deposits, initially produce a mixed REE precipitate or calcine with a REE distribution similar to that in the ore (Goode, 2016). However, the consumers of the REE, the manufacturers of magnets, phosphors, catalysts, optical glass, etc., require separated products with purities generally ranging from 99% to as high as 99.9999% depending on the element in question and the end use. Hence there is a need to separate the individual REE one from the other. This paper is intended to review the options."

Jan 1, 2016

By Thomas E. Finch

Engineering mine design encompasses a range of situations, and each situation has its own range of detail and fineness. The most time consuming, and perhaps repetitive design situation involves evaluation of new or alternate mining methods. Many man years are consumed examing alternatives conjured up at all levels of the design team, from the number crunching engineer to the engineering manager. Many alternatives are intuitively disregarded, some are briefly evaluated and thrown out, and many others are started but not completed due to time constraints. All alternatives have similar input characteristics and evaluation procedures. In the design process, production requirements are known and equipment production capabilities are generated to determine the numbers and costs of an equipment type required to match a given situation. The end result is some comparative figure, typically cost per ton or yard upon which a decision is built. The similarity of input data and problem solving techniques lends design to computer solution. Computer aided equipment evaluation is not new to the mining industry. An existing and accepted technique is exemplified with the programs used by truck manufacturers. Given a haulage profile and production requirements, the number of anyone capacity, horsepower, tire size, gear ratio or similar characteristically identified truck can be determined. This information can be outputted in varying degrees of complexity and the results used with equally varying percentages of credibility by design or production engineers. Most engineers are willing to accept-the computer's effort with relief and a desire for belief. Although inherently more complex, the ultimate end of computer manipulation should be total mine design. This is an extremely large step in the evolution of mine design, and not many engineers, including the authors, believe the results would be directly applicable or necessarily correct. As with computer simulations of an operation, total computer design of mines requires such complex and lengthy input that each mine might be manually designed more quickly and cheaply. The existence of computer programs which initially evaluate a mining system or part of the system is upon us, however.

Jan 1, 1978

By Amar Prakash, V. M. S. R. Murthy, Ajoy Kumar Singh, Avinash Paul, John Loui Porathur

Weak, layered, and fragile rock mass formation, if not supported properly, is subject to roof failure thereby affecting safety and productivity in underground coal mines. Though Central Mining Research Institute – Indian School of Mines Rock Mass Rating (CMRI-ISM RMR) based well-defined support design guidelines are established, still occurrence of roof failures in underground coal mines is a real matter of concern for mining engineers and researchers. Numerical modeling techniques are successfully used by several researchers by simulating rock mass condition for stability assessment of mine openings. The analysis becomes crucial in case of weak and fragile rock formation. The present research envelops the determination of 31 cases of rock load by CMRI-ISM RMR under different geo-mining conditions followed by the development of modified Rock Mass Rating (RMR), i.e., rock mass rating dynamic ( RMRdyn) by incorporating P-wave velocity as a new parameter. The rock load determined using RMRdyn and numerical models was correlated and found in close agreement. In addition, the deviation in rock load determined by all the three approaches, i.e., CMRI-ISM RMR, numerical modeling, and RMRdyn, was compared with the actual field data. The percentage deviation obtained in RMRdyn and numerical modeling is less compared to CMRI-ISM RMR.

Sep 1, 2023

By Benjamin W. Haynes

Cement kiln dust (CKD) produced in the contiguous United States and Hawaii was characterized as part of the Bureau of Mines' program in minerals environmental technology. The mineralogical and chemical composition was determined for 113 CKD samples from 102 plants that normally send CKD waste to landfill. Characterization included the determination of 28 elements, 7 anion species, carbon dioxide, noncarbonate carbon, and chemically bound water. Mercury was determined in 15 samples. Interelement correlation coefficients were determined for 23 elements, 5 anions, CO2, noncarbonate carbon, and chemically bound water. To assess the hazardous waste potential of CKD, the U.S. Environmental Protection Agency Extraction Procedure (EP) toxicity test was performed on all 113 CKD samples. All but one sample were in compliance with the test; the noncomplying sample slightly exceeded the EP toxicity test criterion for lead.

Jan 1, 1982