Search Documents

By W. L. Saunders

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. IT is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel was the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 miles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in. one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of France to the frontier of Hungary, between Italy and the plains of southern Germany. The contour

Jul 1, 1911

By T. Sterry Hunt

WET processes for the extraction of copper from its ores have of late attracted much attention, especially in Europe, where the use of oupriferous iron-pyrites as a' source of sulphur prevails. These processes present an additional interest, when, as is often the case, the copper-ore's to be treated contain one or both of the precious metals, since the complete separation of these from copper, either in the dry or the moist way, is, as is well known, one of the difficult problems of metallurgy. The principal wet processes hitherto in use for the extraction of copper from its ores, may be included under three classes : I. Those in which the copper in snlphuretted ores is rendered soluble in water by calcining them, after a preliminary roasting which removes the greater part of their sulphur, with a portion of common salt, by which the copper is converted into a chloride (Long-maid and Henderson), or with sulphate of soda, by which sulphate of copper is formed (Monnier). Allied to these is the method by which a portion of the copper is got as soluble sulphate by roasting without addition, a process which is sometimes modified and rendered more complete by re-roasting the lixiviated residues with the addition of a portion of raw sulphuretted ore (Bankart). II. Those methods in which free chlorhydric or sulphuric acid is used to dissolve the copper- from oxidized or roasted ores. These, while simple and efficient, are too costly, except in certain localities where chlorhydric acid is a waste product. Related to them is the plan which consists in exposing the oxidized and moistened ores to the slow action of sulphurous acid mixed with air, by which a soluble sulphate of copper is formed. It has been proposed to decompose the solutions of sulphate or chloride of copper by sulphuretted hydrogen, thus separating the copper as sulphide, and using the liberated acid to dissolve fresh portions of oxidized copper. It is, however, the almost universal practice to throw down the copper from its solutions, however obtained, in the metallic state by the use of iron, either scrap-iron or iron-sponge; although in some instances

Jan 1, 1882

By K. C. Sole, M. Makonese

Bushveld Belco is commissioning a plant for production of electrolyte used in vanadium redox flow batteries. Owing to the source material, the electrolyte is contaminated with Fe, at concentrations up to 140 mg/L, which negatively affects battery performance. This study examined the use of ion exchange to reduce the Fe concentration to the target value of < 100 mg/L from a feed solution containing 100 g/L V in 4 M H2SO4. Four resins with possible application were identified: Puromet MTS9570, Puromet MTX7010, Puromet MTS9500, and Puromet MTC1600H. Puromet MTS9570 outperformed the other three resins in all batch experiments with respect to loading capacity and selectivity over V, and was evaluated for Fe removal in fixed-bed column loading tests. Based on these data, preliminary sizing and design of a full-scale column was undertaken. Owing to the difficulty of eluting this resin, a philosophy of discarding the resin on loading to full capacity was considered. These data revealed that, despite the high selectivity of this resin for Fe over V, it would be too expensive and impractical to use this resin for full-scale operation under such conditions. It is recommended to remove iron earlier in the flowsheet prior to generation of the 4 M H2SO4 electrolyte.

Dec 11, 2024

By H. O. Harju

Inco acquired majority interest in the nickel laterite concessions in eastern Guatemala in 1960 and, through its subsidiary Exmibal, extensively explored the deposits until 1965 to define the site for project development on the north shore of Lake Izabal. This paper outlines the exploration methods used to evaluate the Guatemalan laterite deposits.

Jan 1, 1979

By Stephen D. Cramer

The Bureau of Mines conducted a study in which the magnetic fraction of urban refuse was used as melting stock in the preparation of high-strength, low-alloy and carbon steel. Product steels, made from incinerated steel can scrap, nonincinerated-nondetinned steel can scrap, nonincinerated-detinned steel can scrap, and dilutions of these scraps with No. 1 heavy melting scrap, were used in continuing tests in industrial, rural, and marine environments to determine the effect of residual elements and atmospheric pollutants on their atmospheric corrosion resistance. The respective commercial steels were exposed at the same time to establish baseline corrosion data for the test sites. Weight-loss data are reported for atmospheric exposures of 0.5, 1.0, 1.5, and 3.8 years. The marine environment was the most corrosive; the industrial environment was the least corrosive. The atmospheric corrosion resistance of the carbon steel was improved 25 pct by using incinerated scrap and nonin-cinerated-nondetinned scrap in the steelmaking process. In no case was the atmospheric corrosion resistance of carbon steel degraded by using the magnetic fraction of urban refuse as melting stock. The presence of sulfur in the corrosion film was the most important factor affecting the corrosion resistance of the steels. With increasing sulfur concentration, the rate of the corrosion reaction was reduced and the corrosion film became more protective. The residual elements in the product steels most responsible for improving corrosion resistance were copper and tin. These elements tended to increase the concentration of sulfur in the corrosion film. At the levels present in the product steels, Cr, Ni, and Pb had no observable effect on the corrosion resistance of the steels.

Jan 1, 1980

By C. H. Hopper

DIAMOND drills have played an important part in the development of mines for many years. Recently. they have also entered the production field arid the use of diamond drills m the primary breaking of ores has become a big branch of the industry. The writer has estimated roughly that the total diamond drilling in Canada during 1942 was 5,625,000 feet, of which 2,250,000 feet, or 40 per cent, was for blast-holes. This accounts for 6,750,000 tons of ore broken, using the conservative factor of 3 tons per foot of hole. Many consider that the use of diamond drills for blast-holes is the most important advance in mine practice of the past decade, and the industry owes a great deal to the staff of Noranda Mines, Limited, for the pioneering they have done in the development of long-hole mining methods and for publishing their results. A great many mines have followed Noranda&apos;s lead. At the Waite-Amulet, Aldermac, Flin Flon, Canadian Malartic, Hoyle, and Matachewan Consolidated mines, most of the ore is broken by long-hole blasting. While the mines were developing new methods, the diamond-drill industry was developing mechanically-set bits and better machines. Through the effective use o smaller, cheaper diamonds, as well as more efficient setting, bit costs per foot are only one-half what they were ten years ago. Few people realize that a diamond bit is relatively inexpensive. The common EXT coring bit, for example, contains some 200 small diamonds, weighing altogether about 2.70 carats which, at $3.40 per carat, cost $9.20. After use, the equivalent of about 100 of these diamonds may be recovered. Therefore the true cost of the bit is only $7.00, made up of $4.60, the cost of the diamonds lost, $2.00 for setting, and $0.40 tax. The trend in machines has been toward specialization for the different classes of rock in blast-hole work. Light, high-speed machines have been developed for soft ores and higher powered machines for hard ores.

Jan 1, 1943

By A. H. Cronk

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods and costs in the different mining districts. The mining methods described in this paper are employed by one of the large mines in the Illinois fluorspar district. The mine is located at Rosiclare, Ill., and shipments are made over the Illinois Central Railroad: and by barge on the Ohio River.

Jan 1, 1930

By Fengyu Ren, Kunpeng Yu, Gideon Chitomb, Qiangqiang Gao, Liqiang Ma, Jiangtao Zhai, Ichhuy Ngo

The penetration of rock fragments of overlying strata causes advanced ore dilution during drawing. The results of numerical and physical experiments showed that the proposed numerical simulation was applicable and the microscopic parameters of the model were reliable. The penetration under the variables of particle diameter ratio, density ratio, overlying strata thickness, and particle morphology was clarified. The penetration was quantitatively characterized by the discharge amount and the dilution rate. The experimental results showed that the diameter ratio and density ratio had a significant influence on the penetration. On the irregular shape of particles, the penetration is weakened. The overlying strata thickness had little effect on the penetration. This study could provide a theoretical basis for the full section uniform drawing, avoiding advanced ore dilution and further optimization of recovery rate.

Nov 13, 2023

By Catia Casagrande

As principais operações unitárias de um processo de pelotização são: moagem, filtragem, aglomeração e queima. Das etapas citadas, a moagem, como início do processo, é uma etapa crucial para as demais operações. Foi baseado neste fato, que o presente estudo foi realizado, tendo como objetivo principal, avaliar o comportamento das misturas de minério de ferro com diferentes índices de moabilidade e definir os possíveis ajustes dos parâmetros de processo de moagem em função dos diferentes perfis mineralógicos. Foram usadas três misturas de diferentes níveis de índices de moabilidade: baixo, médio e alto, a fim de observar as respostas nas variáveis operacionais de possível atuação na rotina operacional. Para isso, uma matriz de experimento foi realizada, com oito testes para cada mistura de minério de ferro, variando os parâmetros de moagem de mínimo a máximo. As variáveis respostas foram às características físicas das misturas, superfície específica e granulometria, onde foram medidas no sistema automatizado PSI. Através dos resultados dos testes, foram calculados modelos matemáticos de superfície específica e granulometria das misturas em função dos parâmetros operacionais. Os modelos mostraram satisfatórios e aplicáveis, apresentando correlação entre as variáveis dependentes e independentes.

Aug 1, 2018

By W Akpan

The Royal Bafokeng community in South AfricaÆs North West Province represents a unique case in Sub-Saharan Africa in terms of its positioning in the natural resource economy. It receives royalties directly from mining firms for the extraction of Platinum Group Metals, which include platinum, ferrochrome, rhodium and palladium. In 2007, royalty income of about R290 million (approximately US$32.2 million) was reported. Such direct revenues have enabled the community to invest in educational, medical and other social infrastructure, thus complementing governmentÆs social provisioning efforts. Indeed, the Bafokeng community owes its present-day modernisation efforts to mineral rights, and in particular, the legal-institutional arrangement that has enabled it to play an active role in South AfricaÆs lucrative extractive economy. However, the distribution of platinum wealth in this community is not only uneven, but also appears to have had little impact on the broader socio-economic conditions in the community. Despite claims by community leaders of heavy investment in education and skills development, the community continues to be faced with very high levels of unemployment, illiteracy, sprawling informal settlements, poor access to medical facilities and malnutrition. This paper examines the sociological paradoxes and contradictions thrown up by the approach adopted to involve community members in the mobilisation of mining royalties for developmental ends. The central argument is that the current æmodelÆ contradicts the communityÆs stated goals of using platinum wealth to drive up broad-based development and modernisation. This is mainly because it leaves out the vast majority of community members, who are uneducated and unskilled. The core analysis is based on pilot data from an ongoing study in the Royal Bafokeng community.

Jan 1, 2009

By A. G. Moon

Kennecott Copper Corporation&apos;s Chino Mines Division concentrator is located in Hurley, New Mexico. Construction of the concentrator was started in 1910 and its capacity was progressively increased over the years to the present nominal 20, 425 t/d of ore (22, 500 stpd). The principal copper minerals present in the ore are chalcopyrite and chalcocite with much of the chalcotite intimately associated with pyrite. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the deisred pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. In 1972 a major renovation of the flotation and regrinding circuits was com¬pleted and at that time a new lime distribution and control system was placed in operation. Limestone is obtained from a nearby quarry west of Hurley. The limestone is crushed, sized and fed to a rotary kiln and the quicklime product is stored prior to slaking. The lime is slaked, as required, in a mixing tank-classifier type slaker and the lime slurry is pumped to a concentrator storage tank from which it is distributed through a conventional closed loop system. The current average lime usage rate is approximately 6 kg/t of ore (12 lb per st).

Jan 1, 1976

By Caio Oliveira Biondi

A lixiviação de zinco é um processo contínuo que ocorre através da adição de ácido em uma série de tanques, com objetivo de extrair o zinco do material de origem. O ácido deve ser adicionado de forma progressiva para evitar a formação de compostos indesejados e também a formação de espuma decorrente da reação do ácido com o carbonato. O grande desafio do processo é acertar os pontos corretos de adição de ácido para que a lixiviação ocorra com o maior rendimento possível, pois tanto o excesso quanto a falta de ácido prejudicam essa etapa. Com o objetivo de aumentar o rendimento global do processo, a solução de controle avançado baseada em lógica Fuzzy da I.Systems, o Leaf, foi aplicado para substituir o controle tradicional PID e/ou manual. O Leaf foi capaz de reduzir a variabilidade do pH nos tanques em até 25%, fazendo com que fosse possível operar mais tempo no ponto ótimo. Isso permitiu que o rendimento global da etapa de lixiviação aumentasse 0,24%, além de melhoria qualitativa na etapa seguinte de sedimentação. O ganho financeiro proporcionado pela economia de concentrado silicatado foi de 375.000 reais por ano para a Votorantim Metais.

Oct 30, 2017

By Richard P. Walters

This Bureau of Mines report reviews and assesses the technology for preparing electrodeposited coatings of the platinum-group metals from molten alkali metal cyanide baths. Methods are described for the preparation and purification of the cyanide electrolyte. Vacuum drying, fusion, and purity of the cyanide salts are discussed. Use of a sodium borosilicate test tube as a sodium-ion-conducting membrane for the addition of the desired platinum-group metal is described. The optimum plating parameters of potential and current density for Pt, Pd, Rh, Ru, and Ir coatings that result in the best deposits are given. A method for producing platinum-rhodium alloy coatings of predetermined composition is also described. The importance of careful substrate surface preparation is illustrated. While problems still remain with respect to coating porosity, careful application of the methods described permits the preparation of adherent, coherent electrodeposited coatings of the platinum-group metals.

Jan 1, 1984

By G. W. Smith

"The adsorption of dehydroabietylamine acetate on quartz, hematite, rutile and baddeleyite has been deter-mined for concentrations ranging from 0.3 to 5,600 µ. moles/I and for pH values ranging from 2.5 to 10.5.The surface tension, UV and IR spectra, equivalent conductance and ion concentrations for dehydroabiety lamine acetate solutions have been determined.Contact-angle and flotability studies have established that good collection may be obtained with this amine but that selectivity depends on the suitable use of depressants for some of the minerals."

Jan 1, 1971

By O. Jerez, A. Novoselov, L. Gutiérrez, J. Morales, U. Kelm

"In Chile, the evaluation to reprocess tailings for elements other than the traditional Cu, Mo, Au, and Ag, as well as projects to implement long-term monitoring of mining residue sites are key elements of the government’s roadmap laid out for the mining industry for the next two decades. Characterization routines for tailings and mining residues in general have to be adapted from traditional ore and gangue mineral and micro-chemical studies. This contribution summarizes key aspects for the regional mining industry for a basic characterization of tailings with emphasis on small- to medium-size operations with limited in-house facilities and funds to carry out extensive characterization programs. The oldest tailings in Chile were deposited almost a century ago; this fact gives importance to the recovery of past ore /gangue feed information, process circuits and changes (e.g. acid to alkaline flotation), process water provenance and recovery, meteorological registers, and routines of filling a tailings impoundment. Basic characterization should include X-ray fluorescence spectrometry combined with laser diffraction (LD) granulometry followed by X-ray diffraction (XRD), optical microscopy (OM) and automated mineral analysis (AMA) on a reduced set of samples identified by hierarchical cluster analysis. For this detailed stage, only coarse tailings are recommended for direct a study by microscopy and automated mineralogy (P80 >100 µm); for fine tailings (P80 ~30 µm) a combination of XRD and deposit type adapted sequential extraction are more informative options. In particular, for XRD of clay phases, losses of crystallinity may result in deviation of spectra from standard reference phases due to prolonged storage. To monitor surface alteration, scanning electron microscopy can be complemented by Raman spectroscopy to detect residual reagents on mineral surfaces. For reactivity modeling BET measurements are essential."

Jan 1, 2018

By Donald F. Hammer, Donald W. Peterson

The Magma mine at Superior, Arizona, has produced over 13 million tons of ore yielding 1.5 billion pounds of copper. It is a mesathermal deposit, and, although the bulk of the ore has come from the Magma vein, most of the recent production has come from replacement deposits in limestone. The mine lies in a Precambrian and Paleozoic sequence of rocks that includes schist, diabase, quartzite, shale, and limestone; nearby, these rocks are intruded by igneous bodies of Mesozoic age that were probably the source of the ore-bearing fluids. Locally, these rocks are overlain by Cenozoic volcanic rocks and conglomerate. Layered rocks at the mine dip eastward about 30°. The area is extensively faulted, and surface faults are grouped into an earlier east-trending set and a later northtrending set. An additional set of diagonal faults that trends northwest and northeast is recognized underground. The east-trending Magma vein-fault, with its splits and branches, is the principal mineralized structure of the district. The bulk of the ore occurs in large ore shoots that plunge steeply westward and are sporadically connected by irregular ore shoots dipping gently eastward. The main ore controls apparently are selective zones of permeability related to the transverse faults. A bed of crystalline limestone near the base of the Martin Limestone (Devonian) is the host for the replacement ore bodies-discontinuous tabular pods dipping eastward parallel to the bedding. Selective permeability is again the apparent ore control, caused both by local hydrothermal solution of limestone and by deformation along faults. The principal copper minerals in the vein are chalcopyrite, bornite, enargite, tennantite, chalcocite, and digenite; these minerals vary in abundance according to a distinct zoning pattern. The upper part of the mine yielded considerable zinc as sphalerite, and the oxidized zone was rich in silver. The chief gangue minerals are pyrite, quartz, and hematite. In the limestone replacement bodies, chalcopyrite and bornite are the chief ore minerals.

Jan 1, 1968

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988

By S. S. Clarke

This paper on methods and costs of mining at the Westside mine, in the Tri-State zinc-and lead-mining district (Missouri-Kansas-Oklahoma), is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in various mining districts of the United States. Methods and equipment used in drilling, loading, and underground transportation have changed radically since the latest Bureau of Mines publications2/ on mining methods in the district were published more than 20 years ago. More efficient methods and machines have been developed in order to maintain low operating costs in the face of rising labor and supply costs and lower grade ore. The rate of conversion to mine mechanization was disappointing at times; local conditions required the development of special equipment, and available rock-moving machines had to be remodeled and strengthened.

Jan 1, 1957

By Arthur L. de Carle

"IntroductionThe Key Lake uranium-nickel deposits are located within a Mineral Lease centred at latitude 57 ° 12' north and longitude 105 °39' west along the southeastern rim of the Athabasca sedimentary basin in northern Saskatchewan, approximately 240 km north of La Ronge (Fig. 1). Access is provided by an allweather provincial highway from Pinchousc, situated about 200 km to the south, and a private airstrip maintained at the mincsitc.These deposits have been developed by Key Lake Mining Corporation on behalf of the Saskatchewan Uranium Joint Venture. Participants in the joint venture include Saskatchewan Mining Development Corporation (50%), Urancrz Exploration and Mining Limited (33 1/3 %) and Eldor Resources Limited (16 2/3 %).Considerable geological work has been conducted on the Key Lake orebodies and reported in summary papers published by Dahlkamp and Thn, (1977), Dahlkamp, (1978), Gatzweiler eta/., (1979) and Kirchner el a/. , (1980). However, intensive geological research is ongoing, particularly since many problems regarding ore genesis and controls remain unresolved . Exploration History and DevelopmentThe events (Gatzweiler eta/., 1980) which led to the discovery of the Key Lake ore bodies began in the summer of 1971 by following up on the reports of airborne radiometric anomalies and anomalous radon values in the Zimmer Lake water situated approximately 5 km to 6 km to the southwest. This work succeeded in locating a few high-grade uranium and nickel-bearing boulders associated with esker material. An integrated program, consisting of various geochemical and geophysical surveys along with diamond drilling, culminated in the discovery of the Gaertner orebody during July 1975. Subsequent fence drilling across the strike extensions of this ore structure located the Deilmann deposit, approximately I km to the northeast, in June 1976"

Jan 1, 1986

By Helênio Resende Silva Júnior, Thiago de Oliveira Mazzeu

O envelhecimento gradual das Baterias de Coque é um fato inevitável, sendo importante monitorar as condições dos fornos e das estruturas periféricas para maximizar sua vida útil. A Paul Wurth desenvolveu uma metodologia de diagnose que avalia as condições dos elementos principais que compõem as plantas de Coqueria, dentre elas: estrutura da alvenaria refratária, estruturas e componentes metálicos, análise do controle térmico e regime de pressões, conjunto das máquinas móveis. Através de inspeções visuais e coleta de informações de processo e rotina adotada pela equipe de preservação da planta de Coqueria, são elaborados procedimentos e recomendações que visam à extensão da vida útil do equipamento. A Diagnose é uma técnica que auxilia as equipes de Coqueria a entenderem em que situação o equipamento se encontra e contribui com as melhores práticas adotadas no mercado para o prolongamento da vida útil. Ela deve ser repetida com frequência de modo a atualizar a situação da Bateria de Coque, verificar o efeito das ações tomadas pela equipe de preservação e propor novas recomendações. A Diagnose ainda permite identificar a idade real de desgaste das estruturas da Bateria em comparação com sua idade cronológica, permitindo que as usinas planejem investimentos de maior porte.

Oct 1, 2019