Search Documents

By Earle S. Burnett

Rotating piston deadweight gages have been used for many years for measurement of pressure to several hundred atmospheres. They have been calibrated by comparison of fluid pressures produced by various loads bearing on the piston bases, as measured by corresponding heights of balancing columns of mercury. When expressed in appropriate units, these ratios of column heights to piston loads are called piston constants. Experimental arrangements and procedures for their determination are presented in this paper, followed by a discussion of their significance and of their subsequent applications.

Jan 1, 1966

By E. J. Gleim

[THE ORGANIC act under which Federal Bureau of Mines was established provided for the investigation of the safe use of electricity in mines. Each Congress appropriates funds for conducting this investigation. As part of this investigation, electrical apparatus used in mines is studied to determine if its operation and use might introduce a hazard. From this study, certain safety standards have been developed. These standards, established with the aid of both the manufacturer and user of such apparatus, are published in schedules, and apparatus that complies with the requirements set forth these schedules is classified as "permissible." This term is defined to designate apparatus as "completely assembled and conforming in every respect with the design formally approved by the Bureau of Mines." In the judgment of the Bureau, the manufacturers of such apparatus have adhered to certain minimum standards of safety in supplying a product that when properly used and maintained is safe for operation in mines where flammable gas or coal dust may accumulate. This work of the Bureau of Mines for increasing safety does not make it obligatory for manufacturers of mine equipment to produce only that of permissible classification. Before the effective date of the Federal Mine Safety Code,5 the Bureau sought to promote safety by recommending that mine operators install permissible equipment in gassy mines as a preventive measure against gas and dust explosions initiated by electrical equipment. For some years, the mining laws of several States have prescribed the conditions under which permissible equipment must be used. The Federal Mine Safety Code requires that ?all new electric face equipment and replacements of equipment purchased for mines where nonpermissible equipment is now being used shall be of a permissible type approved by the United States Bureau of Mines,]

Jan 1, 1955

By Robert S. Warfield

The Federal Bureau of mines and U.S. Geological Survey conducted exploratory investigations and geologic mapping in the Wishbone Hill district of the Matanuska coalfield almost continuously from 1942 through 1958. These investigations delineated reserves of high-volatile bituminous coal necessary to supply the rapidly expanding military and civilian requirements in the Anchorage area. This report describes the program conducted by the Bureau of Mines from 1949 through 1958, and briefly summarizes previous investigations, the results of which have already been published. The coal-bearing structure on both the north and south limbs of the prominent Wishbone Hill syncline was explored by 8,719 feet of churn drilling and 25,460 feet of diamond-core drilling. A total of 33 holes were drilled ranging in depth from 60 to 2,114 feet. To supplement the drilling operations, bulldozer and dragline trenching were undertaken at key locations; about 25,000 cubic yards of dragline trench were excavated in the vicinity of the old Premier mine.

Jan 1, 1962

By Raymond B. Ladoo

"The name bentonite has been applied to a group or series of clay-like materials characterized by an alkaline oxide and alkaline earth content of 5 to 10 per cent, fine grain Giza, high absorptive powers, and usually very strong colloidal properties.Bentonite probably represents no mineral of fixed composition, and its physical properties vary considerably. The type material from Wyoming is light yellow or greenish yellow in color, but from other localities it may be cream colored, white, gray, pink, dark brown or even black. It is exceedingly fine grained, very plastic and highly absorbent. The appearance may be dull or powdeay, but a freshly cut surface usually has a waxy luster. Some varieties have the appearance of wax and may be cut into very thin, translucent shavings. The fracture of the type material is roughly conchoidal, that of other varieties is platey and shale-like, while still others have no typical fracture. Bentonite is highly absorbent; .hen wetted it will absorb more than three times its weight or seven times its volume of water. Some varieties when wetted with water expand to more than six times (some experimenters report eight times) their original volume. The wetted material is exceedingly smooth and soft and feels like soft soap. Unlike most clays, bentonite is easily fusible at a comparatively low temperature.Under a high-power microscope bentonite seems to consist of extremely small, more or less rounded, grains of uniform size, but the texture of most varieties is so fine that individual grains can not be distinguished.Some varieties when finely ground and thoroughly agitated with water will stay in suspension indefinitely, forming a translucent gelatinous mass. The addition of small amounts of acids or sodium chloride seems to have little or no tendency to raid coagulation or settling. Other varieties of similar analysis and appearance go into suspension more easily, but settle out again in a comparatively short time. It has been suggested that the material which stays in suspension indefinitely is a true colloid of the emulsion or lyophilic type."

Oct 1, 1921

By K. N. Subramanian

Previously reported work on total oxidative leaching of chalcopyrite concentrates ha s shown that high copper extractions are obtained at 210°C and 0.4 MPa oxygen pressure. A simple integrated flow sheet using pressure leaching, solution treatment involving precipitation with a calcium base, and electrowinning to produce wire-bar-quality copper is described. Reagent and energy requirements developed from this work indicate that the process could be attractive for small operations where a smelting-refining complex cannot be justified.

Jan 1, 1978

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2017

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck, Y. Zheng

Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27 percent of respirable coal mine dust can be attributed to longwall shield movement, and developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine the ability of the foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used: compressed air and blower air. Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For compressed air foam in 3.3 m/s (650 fpm) ventilation, 98 percent of agent A was intact while 95 percent of agent B was intact on the roof at three minutes after application. At 30 minutes after application, 94 percent of agent A was intact while only 20 percent of agent B remained. For blower air in 3.3 m/s (650 fpm) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 min after application, 74 to 92 percent of foam agent A remained, while 3 to 50 percent of foam agent B remained. Compressed air foam seems to remain intact for longer durations and is easier to apply than blower air foam. However, more water drained from the foam when using compressed air foam, which demonstrates that blower air foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able to withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control.

Jan 1, 2018

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By Alfonso Núñez

There are many assets on a typical industrial site that are not monitored continuously by a SCADA system or the DCS. Many of these assets are critical and must be running correctly for production to meet its targets. Most companies schedule inspections of these assets regularly by sending skilled operators to the field who take notes using paper and a clipboard. There are many advantages related to the digital transformation of operator rounds. In particular, the collection process is supported by digital prompts and the data — once it is collected — is automatically routed to a database and made readily available to all the software applications and stakeholders that need it.

Sep 29, 2023

By Thomas Gales

Longwall mining of thin shallow coal seams utilizing open pits is technically feasible. The thinnest coal seam which can be mined using available technology is 34 inches. The capital expenditure for a 1,000,000 ton per year operation is $15,494,000, and the projected rate of return is 5 percent. Similar statistics for a conventional area surface mine are S18,937,000 capital and 14 percent rate of return. The longwall surface mining method disturbs 63 acres of land per 1,000,000 tons, and the conventional area surface mine disturbs 198 acres A significant bibliography of the technology involved is included.

Jan 1, 1976

By Robert H. Merrill, James V. Williamson, David M. Ropchan, George H. Kruse

In- situ rock stresses were determined by flatjack and borehole - deformation methods . Estimates of the stress distribution around a flatjack were obtained by a combination of flatjack and borehole - gage techniques . The investigations were part of a study , conducted jointly by the State of California and the Federal Bureau of Mines , to determine the stress in rock at the site of an underground powerplant for the Oroville Dam near Oroville , California . The stress distribution around each of three flatjacks was nonsymmetric ; however , stresses obtained from 9 flatjack and 157 borehole measurements are considered reasonably accurate for engineering purposes . The stress near the edge of the openings is between 800 and 1,600 psi ; the stress in the undisturbed rock is approximately 500 psi , nearly hydrostatic .

Jan 1, 1964

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

By D. J. MacDonald

The Bureau of Mines has conducted bench-scale investigations leading to the design of an integrated process for producing reactor-grade zir-conium oxide (Zr02) from zircon sand, which avoids the air pollution, water pollution, fire hazard, and odor problems associated with the hexone-thiocyanate process. The integrated process consists of three steps: production of crude zirconyl sulfate solution, solvent extraction, and production of Zr02 from strip liquor. This report describes the solvent extraction step. Multistage, countercurrent liquid-liquid extraction with a tertiary amine in kerosine was used to separate zirconium from a dilute H2S04 solution containing hafnium and other impurities. Process steps de-scribed include extraction from an aqueous feed solution to form a hafnium-contaminated, zirconium-bearing organic-phase solution, scrubbing to separate zirconium from coextracted hafnium, stripping to transfer hafnium-free zirconium into an aqueous strip liquor, chloride-loading to produce a chloride-bearing organic solution, scrubbing with the chloride-loaded organic solution to remove traces of uranium impur-ity from the zirconium-bearing strip liquor, and regeneration to pre-pare the organic solution for reuse. These steps were performed simul-taneously in steady-state, bench-scale experiments. Zirconium recovery of up to 93 pct was achieved. Results of an economic evaluation are included.

Jan 1, 1984

Adams, John H., Pres. & Mgr., Alabama Lime & Stone Corpn., 1302-4-8 First Ave., Birmingham, Ala. '14 Adams, L. W., Otis Steel Co., Riverside Plant Cleveland, Ohio. '15 Adams, Leland D., Min. Engr., Mgr., Signal Mines Co., Goldbanks Quicksilver Co., 485 California St., San Francisco, Cal. '14 Adams, R. L., Min. Engr., Old Ben Coal Corpn., Mine 12 Christopher, III. `19 Adams, Robert M., Robert M. Adams Co 1201 Fidelity Bldg., Duluth, Minn. '20

Jan 1, 1925

By S. L. Zekovic

This paper analysis the medium and long-term perspectives, framework and considered possibilities of sustainable development of RTB "Bor" (Copper mines in East Serbia) after consolidation in the period of transition. The copper mine was opened in 1903. and today is the best quality copper producer on Balcan. This paper are elaborates the problems of privatization, debt, investment, growth of copper production from own mines (and imported raw), opening of new mines, economical efficiency of production, markets, environmental problems and impacts of the recent industry consolidation. The RTB "Bor" is a serious hot spot in Serbia. Unsustainable trends and processes are identified, as follows: open-pit waste dumps, flotation tailings, mining and processing waste waters, air pollution; no efficiency (excessive) using nonrenewal resource in the copper production; inefficiency in the use of energy, water and other inputs in copper complex; transboundary character of emissions of dust; environmental degradation and quality of wide area and ecologically highly risk, etc. Analysing some trends and planning-developmental perspectives and development strategies of company, it might be assumed that in the forth coming period, in parts of the Serbia, the borders areas of Bulgaria and Romania, there is an anticipated increase of ecological risk.

Jan 1, 2007

By AIME AIME

EVERETTE LEE DEGOLYER, past President of the Institute and Anthony F. Lucas Medalist, was presented with the John Fritz Medal at a dinner at the Wal-dorf-Astoria Hotel in New York, Jan. 14. Dr. DeGolyer is the third representative of the Institute in recent years to receive the John Fritz Medal which is awarded jointly by the four Founder Engineering Societies through a board composed of sixteen past presidents. In 1938 Paul D. Merica was given the award "for important contributions to the development of alloys for industrial uses" and in 1933 the distinction was given to D. C. Jackling "for notable industrial achievement in initiating mass production of copper from low-grade ores through application of engineering principles."

Jan 1, 1942

By E. Van Den Neste

A concise historical review is given of the Overpelt plant and the general principles of zinc hydrometallurgy are briefly outlined, together with a description of the new electrolytic zinc plant ore roasting process and, more particularly, the original Overpelt roasting process. A detailed description of the flowsheet of the zinc electrowinning plant, .with an annual capacity of 100,000 t, successfully put into operation in May 1974, is given. The treatment of the residues is performed following the goethite process ; the purification is continuous in two steps; the tank house is equipped with cells containing jumbo cathodes; the handling and stripping of the cathodes is fully mechanized. Concluding the description, some metallurgical and other features of the project are explained in detail.

Jan 1, 1977

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by The Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on Figure 13 in Volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township-is given with the discussion covering that area.

Jan 1, 1948

By John T. Cumberlidge, Frederic M. Chace

Nickel-bearing saprolite developed during the early Tertiary over a northeast trending ultramafic body of Jurassic age near Riddle in southwestern Oregon. The principal nickel mineral is garnierite, but other complex nickel minerals may be present. There are two main ore bodies, an upper (older) one associated with the Klamath peneplain, and a lower (younger) one on the Sherwood peneplain. Saprolite constitutes the bulk of the ore and was probably derived from peridotite and dunite through chemical decomposition by downward percolating meteoric groundwater. Decomposition took place by net loss of MgO, SiO2, and Fe without a change in volume. Faults and joints provided permeable zones which localized saprolite development, and faulting may have helped preserve some ore from loss by erosion. Garnierite-chalcedony boxwork ore was deposited by meteoric groundwater along faults, joints, and at the level of former water tables. Boxwork ore is entirely supergene, the chemical constituents having been derived from higher in the soil profile. The saprolites show evidence of both supergene and residual enrichment in nickel. Red and yellow soil occurs as a capping over saprolite and boxwork, and was derived from them by chemical and mechanical decomposition. The present deposits are probably truncated remnants of a formerly thicker and much more extensive deposit which probably included laterite at the surface. The deposits started to form in the early Tertiary due to deep chemical weathering under sub-tropical to warmtemperature conditions. Early Tertiary ero~ion surfaces of low relief probably contributed to the predominance of chemical weathering over mechanical erosion. Alteration under present climatic conditions favors the formation of soil from saprolite rather than the formation of new saprolite from peridotite.

Jan 1, 1968