Search Documents

By James W. Weaver

The 2,120-foot long cable stayed Penobscot Narrows Bridge that carries US Route 1 over the Penobscot River between Verona Island and Prospect, Maine is supported on four foundation units, one below each pylon and one at each abutment. Due to varying subsurface conditions along the bridge alignment, the structure was designed to be supported on foundations consisting of high-capacity steel H-section piles (Verona Pylon), a mat bearing on a prepared bedrock surface (Prospect Pylon) and spread footings bearing on compacted rockfill (abutments). The 70-foot by 80-foot (plan area) Verona Pylon foundation was designed to be supported by 288, 430-kip design capacity steel H-section piles (HP14x117, 50 ksi steel) driven through up to 100 feet of dense glacial till deposits containing cobbles and boulders up to 3 feet in diameter. The piles were installed using a single-acting diesel hammer (Delmag D62-22) with a maximum rated energy of 165 kip-ft. Thirteen representative piles were selected for dynamic testing (ASTM D-4945) to verify pile capacity, hammer efficiency and pile stresses. Dynamic testing determined that four different pile driving criteria were needed across the site due to variation in the bedrock and soil resistance below the footing plan area. Approximately 4 percent of the production piles were damaged/rejected due to misalignment and/or damage as a result of encountering the cobbles and boulders embedded in the glacial till. The rejected piles were located randomly throughout the plan limits of the foundation mat. Subsequent structural analyses indicated that the foundation was capable of safely supporting the design loads without the need for installing replacement piles. Evaluation of dynamic testing results with signal matching and pile driving records provided valuable information on pile side and tip resistance. Evaluations were made regarding predicted versus actual pile lengths, pile bearing material, distribution of skin friction and end bearing capacities.

Jan 1, 2011

By P Steinier

Most operations, when considering their comminution circuit, are primarily concerned with achieving the desired particle size distribution to obtain adequate liberation for the separation process, at minimum cost. Invariably, the effect the grinding media has on the subsequent separation process (ie flotation, leaching) is not taken into account when selecting the media. This choice is driven by cost rather than metallurgical outcomes. Maximising valuable mineral recovery, with optimum selectivity against gangue minerals, is about good particle preparation. And, particle preparation is strongly related to achieving adequate mineral liberation with the correct pulp chemical conditions. However, the pulp chemistry of a system is largely ignored and relies heavily on pH control and the addition of appropriate reagents (collectors, frothers, activators, depressants). The changes effected by the addition of the various reagents are obtained through conditioning the ground pulp prior to or during the concentration stage, subsequent to grinding. Frequently, reagents are added during grinding with good effect, but the impact of the grinding media on down stream processing is usually overlooked. A number of case studies examining the effect of grinding media on pulp chemistry and subsequent flotation performance were completed on several different sulfide mineral systems (for example, lead/zinc, copper, refractory gold). The evidence suggests that a change in grinding media type from forged to high chrome (ie conditioning the pulp during grinding) resulted in a shift in pulp Eh to less reducing conditions, an increase in the dissolved oxygen content of the pulp and a reduction in the iron species present. The changes have a positive impact on flotation behaviour. The results of the case studies are discussed.

Jan 1, 2004

By Paola Vera, Magali Candia

La gestión de Derechos Humanos (DDHH) de Antapaccay ha completado un proceso de consolidación hasta ser parte de nuestra cultura organizacional, desarrollando nuestras actividades empresariales basadas en el respeto a los derechos humanos y que hoy es parte de nuestro sistema integral de gestión HSEC-HR (HR=Human Rights). Dicho proceso inició con “conocer” basado en el aprendizaje y comprensión de nuestro rol empresarial frente a los derechos humanos y mejora continua, pasando a “involucrarnos” con un enfoque preventivo en la evaluación preventiva de riesgos y mitigación de impactos.

Sep 29, 2023

By Daniela Rodríguez

El presente trabajo tiene como objetivo resaltar la importancia de las obligaciones inherentes a la relación del Estado peruano con un inversionista del sector minero -conocidas a nivel internacional como Legítimas Expectativas-, y pone en evidencia que su análisis en los casos concretos de redacción de normas aplicables al sector minero podría disminuir el número de controversias llevadas a arbitraje y a su vez -en virtud de una buena imagen internacional- permitiría potenciar la inversión privada en el país.

Sep 29, 2023

By Oswaldo Ortiz Sánchez

El presente trabajo describe la alternativa de uso del mortero de resina en la fijación de pernos de anclaje de las excavaciones mineras, consolidación y disipación de vibraciones en los cimientos de plataformas para la instalación de molinos, winches, tolvas, etc. Esta opción surge en respuesta al problema de reforzamiento con pernos de anclaje en ambientes con aguas corrosivas o en proceso de deformación acelerada en las excavaciones mineras, así como ante obstáculos de subsidencia de cimentación en plataformas, donde se encuentran instalados equipos de gran tonelaje, y que producen fuertes vibraciones durante su funcionamiento.

Jul 31, 2003

By Mario A. Espinoza

"El presente texto señala la función del médico en la prevención de las enfermedades ocupacionales. La Salud Ocupacional, no solo concierne a la prevención de las enfermedades ocupacionales, debidas a la inhalaciónde ciertas sustancias químicas como el plomo, benzol, polvos de sílice u otras, sino que estudia los efectos fisiológicos del trabajo y ambiente físico y psicosocial del trabajador. En ese sentido, es importante la participación de profesionales en los programas de salud ocupacional como la del médico quien se encarga de aceptar a los postuiantes que física y mentalmente están capacitados para realizar trabajos sin ninguna limitación, clasificar a los postulantes que no demuestren aptitud para el trabajo que solicitan, asignándoles otras colocaciones y los proteje de los riesgos inherentes al trabajo a través de una distribución adecuada de sus funciones. "

Sep 1, 1971

The twenty-ninth regular meeting of the Rocky Mountain Coal Mining Institute was called to order at 11:30 o'clock a. m., Monday, May 26, 1930, President B. W. Snodgrass presiding: PRESIDENT SNODGRASS (condensed report): The meeting will please come to order. As President of your Institute, I take pleasure in welcoming you to this convention, and to those who come from outside of the city, I take pleasure in Welcoming you to the city of Denver. This is the first convention at Denver in fifteen months. I hope that the annual rather than the semi-annual meetings will prove satisfactory to all, and that no mistake has been made in that respect. We are gathered together here to discuss problems common to all of us, and I am sure that we will profit by such discussion. We have with us, outside of the membership of our organization, representatives of two other organizations, Mr. Callbreath of the American Mining Congress, and Mr. Huntress of the National Coal Association. We will be honored by having them with us, and we shall expect to hear from them during this meeting.

Jan 1, 1930

By D. Rahal

All ores have an economic optimum particle size (Wills and Napier-Munn, 2006). This optimum value is often a compromise between the need to achieve adequate liberation for the efficient separation and recovery of valuable minerals and the energy consumed by the crushing and grinding process. It has been recognized for nearly three decades that grinding is the most expensive and least efficient stage in mineral processing (El-shall and Somasundaran, 1984). At that time it was estimated that grinding consumed between 25 and 70% of the total power required in mineral processing. This recognition drove the development of new stirred mill fine grinding technology in the 1990s (Jankovic et.al, 2003; Enderle et. al., 1997; Massey, 2008). These milling technologies have a reduced energy consumption compared to traditional fine grinding using ball mills. In the ?coarser? fine grinding applications this improvement is approximately 30%. The benefits increase to above 50% in ultrafine grinding applications (Lichter and Davey, 2006). Despite these gains, the US Department of Energy reported that an additional energy savings of up to 37% is possible in the minerals industry. They identified continuing research and development and implementing best practices in both grinding and materials handling as the primary avenues for the additional reduction (BCS, 2007).

Jan 1, 2011

By Daniel García

La lixiviación por presión es una alternativa hidrometalúrgica desarrollada para minerales metales básicos, donde se reduce la contaminación generada por solubilización del azufre y su separación. En este sentido, el presente texto señala la influencia del quebracho como agente tensoactivo que evita el problema causado por el azufre, utilizando concentrados cuyas especies mineralógicas predominantes son: esfalerita, pirita, galena y cobre grises, de forma que incrementa la extracción de los metales de valor, entre otros.

Oct 21, 2015

By Chririnos. J.

Ante el desabastecimiento del método de explotación de tajeo abierto ascendente con sostenimiento de puntales, empleado en la mina Algamarca, Cajamarca, se sugirió la aplicación de dos nuevos métodos de explotación: almacenamiento provisional y corte de relleno. El primer método es aplicable en aquellos casos donde las rocas de caja sean consistentes y que la veta uniforme que no sea arcillosa, mientras que el segundo, es factible en aquellos blocks donde las rocas de caja sean poco consistentes. En este sentido, el objetivo del texto es señalar la factibilidad de ambos métodos sobre diversos aspectos de carácter técnico-económico, considerando que el ancho de la explotación sea de 0.94 m, para que la utilidad sea más provechosa.

Nov 20, 1972

By K. P. Wright

"Twenty-five years ago, there were about thirty-two gold mines operating in Canada; nine of these have been in continuous operation since then and are still operating. Three of these are part of the Dome Group. Operations of these three and of the newer mines in the Group are referred to in discussing process development over the last twenty-five years.Of the Dome Mines Group, Dome Mines Limited, Sigma Mines (Quebec) Limited, Campbell Red Lake Mines Limited, Detour Lake Mine and Kiena Gold Mines Limited, three have been in continuous operation for the last twenty-five years. Dome has operated for seventy-seven years; Sigma about to complete fifty years, and Campbell approaching forty. Overall, milling processes are virtually the same as they were twenty-five years ago. Tota1 go1d production from the three mines has hardly changed; 1960 production, 416,700 ozs. versus 411,300 in 1985. Milling costs have risen by a factor of six or seven and gold price from $35/oz. in 1960 to $322 in 1985.Basic flowsheets are relatively unchanged. Sigma is an all cyanidation mill grinding in cyanide solution; Dome operates gravity concentration and cyanidation; Campbell gravity concentration, flotation, roasting and cyanidation. All three use Merrill-Crowe zinc precipitation.Detour and Kiena are two examples of the major change in gold processing in the last twenty-five years - carbon-in-pulp. This process has brought along with it other changes, such as, carbon stripping and reactivation, electrowinning, and induction furnace melting. Modern mill design with its use of outside thickeners and agitators, bulk handling of reagents, instrumentation, etc., has made a radical change in operating conditions and appearance of the new plants."

Jan 1, 1987

La importancia del desarrollo de centros mineros en las diversas regiones del país, no solo responde al redescubrimiento de algunos yacimientos mineros abandonados, sino a la permanencia de dicha actividad, a través de la reactualización de sus elementos corporativos y el uso de sus instalaciones. Por tal motivo, el objetivo del presente trabajo busca repotenciar la producción de dicha minera -en tanto mantenga sus labores y mejore su método de explotación-, asi como contribuya al desarrollo económico-social de la provincia Grau y Ccochasayguas. La provincia de Grau, ubicada en Apurímac mantiene un tradición minera que se remonta al periodo colonial, donde funcionaron dos intendencias mineras: una en Haquira, que vigila las explotaciones auríferas de Osoollo, Anyo y Patario, y la otra, en Curpahuasi. Posteriormente en 1890, un minero apellidado Rodriguez, redescubrió el mineral de Ccochasayguas para cuya explotación Samanez, Bottger y Letona de Abancay formaron una sociedad, y luego con la intervención de Amadeo de Piérola, se transformó en La Cotabambas Auraria. Después de una serie de altibajos, Ccochasayguas logró posicionarse como la mina más importante de oro que tuvo el Perú. De otro lado, en 1931, la Compañía Exploradora Cotabambas instaló en Progreso una Planta hidroeléctrica, facilitando la importación de la perforación mécanica en las minas, con compresoras y perforadora. La oficina de Progreso abarca los distritos de Cotabambas, Tambobamba, Haquira, Huayllati, Mamara, Ourpahuasi y Vilcabamba, encontrándose en esta zona minas de cobre, plomo, plata y oro. Empero la labor de la minera Ccochasayguas se detuvo debido algunos inconvenientes económicas, eliminando actividades de apoyo a dicha comunidad. La rehabilitación económica de Grau, depende de que nuevamente puedan organizarse trabajos mineros, así como se reutilizen dichos depósitos mineros para brindar trabajo remunerado a la población obrera de Grau, y conseguir a favor del Estado, una mayor producción exportable de metales.

Jul 20, 1957

By Alfonso Jaime

El presente texto describe la experiencia en el manejo de presupuesto operativos desarrollado por la empresa Minsur S. A. En este sentido, la instalación de una planta de subproductos como última inversión en la infraestructura, permitió mejorar la producción de metálico, mejorar los estándares internos de la compañía y establecer las bases para una mejora continua. Como consecuencia de esta inversión, la empresa ha implementado un software de clase mundial, donde se logró modificar diversos procedimientos internos, los que no podían desarrollarse eficientemente debido a la cantidad de información que requerían y la falta de recursos disponibles para su manejo. Por ello, se plantea una nueva formulación en el presupuesto y control de costo que comprende: la orden de mantenimiento, las clases de actividades, facturación, el subreparto, valor estadístico, centro de costo, puesto de trabajo, receta de materiales,

Sep 13, 2001

REFERENCES AND FOOTNOTES 1. U.S. Department of the Interior, Office of Surface Mining. Surface Coal Mining Reclamation: 10 Years of Progress: 1977-1987. Washington, D.C. August 3, 1987.48 pp. (For sale by the Superintendent of Documents, U. S. Government Printing Office, Washington D.C. 20402.) 2. The Rural Abandoned Mine Program (RAMP), authorized by Section 406 of SMCRA, provides for the control and prevention o f erosion and sediment damages from unreclaimed abandoned mine lands. 3. The Small Operator Assistance Program (SOAP), authorized by Section 401(b)(1) and 507(c) of SMCRA authorizes up to 10 percent of the fees collected for the Abandoned Mine Reclamation Fund to be used for technical assistance to help qualified small mine operators obtain techincal data needed for permit applications. Operators who produce fewer than 300,000 tons of coal per year are eligible for assistance. 4. OSM regulations 30 CFR 816.42 and 817.42 require water from areas distrubed by mining activities be in compliance with all applicable state and federal water-quality laws and effluent limitations for coal mining established by the U.S. Environmental Protection Agency. 5. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 6. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 7. Source: OSM Field Office Annual Reports. 8. Johnson, W. and G.C. Miller, Abandoned Coal-Mine Lands: nature, extent, and cost of reclamation. U. S. Bureau of Mines, 1979,29 pp. PHOTOGRAPHIC CREDITS Front cover, pp. i, 1, 2 bottom, 7 right, 10 bottom left, l 1 top, l l bottom right, 12 top, 13 bottom, 14 bottom right, 15,16 bottom, 17 top, 17 bottom right, 18 bottom, 19, 20 bottom, 21 top, 22, 23, 24 bottom, 25 bottom, 26 bottom left, 26 bottom right, 27, 28, 29 top, 30 bottom, 32 bottom right, 33 top, 34 top, 35 top left, 35 bottom left, 35 bottom right, 36 top, 37, top right, 37 bottom, 38 bottom, 39, 41, 42 top, 43 bottom, 44 bottom left, 44 bottom right, 45, 46, 47, and 53: Chuck Meyers, OSM. Page 2 top and center: Tony Fuhs. Page 3: John Sharkowicz, OSM. Page 6 left: North American Coal Corp. Pages 6 right, 7 left, l l bottom left, 13 top left, 13 top right, 17 bottom left, 21 bottom, 25 top left, 25 top right, 29 bottom, 30 center, 32 top, 32 bottom left, and 38 top: Bob Welch, OSM. Page 10 top left: Donald Stump, OSM. Pages 10 right, 14 top right, 14 center right, 18 top, and 44 top: Ron Hill, EPA. Page 12 bottom: Texas Utilities Co. Pages 16 top, 20 top, 24 top: Tennessee Valley Authority. Page 26 top right and 26 center left: Richard Dick, U.S. Bureau of Mines. Pages 30 top, 33 bottom left, 33 bottom right, 35 top right, 36 bottom, 37 top left, 40 top, 40 bottom, 42 bottom, 43 top left, and 43 top right: Jim Boyer, OSM. Page 31 top left, and 31 top right: Bruce Wage, Western Energy Co. Page 31 bottom: Rex Wilson, OSM. Page 34 bottom: West Virginia Division of Abandoned Mine Lands. Page 35 center: William Weist, Jr., OSM.

Jan 1, 1992

By Bradley Stoughton

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.-J. S.] INTRODUCTION. THIS paper gives the results : first, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows: 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such as, for example, the wear of railroad-rails, of steel and chilled-iron .rolls, car-wheels, etc. 2. These improvements seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example : A series of tests on cast iron

Nov 1, 1912

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

This study relates to continuous face haulage systems in underground coal mines, and was performed by Joy Manufacturing Company for the U. S. Bureau of Mines under the Bureau of Mines Contract No. HO 242025. The effective starting date for this work was June 14, 1974. There were two main reasons for making this study, the first being to find a safer system to move coal away from the face than the currently predominant shuttle car system, and the second being to seek ways to advance the state-of-the-art of continuous face haulage as a means of increasing coal production.

Jan 1, 1975

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012