Search Documents

By Zhihong Liu

Monodisperse micron size nickel oxalate particles with rhombohedron morphology were prepared from condensed Ni(OH)2 suspension by a novel gel-sol process proposed by one of the authors. Firstly, condensed nickel hydroxide gel was formed by fast adding 1 mol dm-3 NaOH solution into 0.2 mol dm-3 nickel chloride solution, and then oxalic acid solution with a concentration of 0.25 mol dm-3 was dropped into the gel drop wise through a pump equiped with a pH controller under preset pH value, and in this process, Ni(OH)2 gel was converted gradually into monodisperse nickel oxalate sol. The formation of the nickel oxalate particles was found to proceed through a dissolution-recrystallization mechanism from the nickel hydroxide gel. The product particles exhibited rhombohedron like shape with micron size long axis and sub-micron size short axis. The effects of such factors, as temperature, surfactants, et al, were evaluated experimentally on the particles sizes and morphologies.

Jan 1, 2006

By J. Bleeck, G. Mahrt

INTRODUCTION Many excellent papers have been written and presented regarding agricultural lime and the subject has been covered extensively in books concerning soil science, fertilizing, limestone, etc. We felt challenged to construct a paper that wouldn’t merely be a repetition of past presentations. Therefore, we chose to begin with factors having the most impact on plant growth realizing that the audience is likely to be relatively unfamiliar with this subject. So, we decided to dig deep into the roots of soil and plant growth science in order to better understand the significant role of limestone in this important area. The soil with the higher plants growing upon it forms an open and dynamic ecosystem in which there is flux of energy and material (heat, light, water, nutrients, mineral and organic matter, organisms). Plants root in the soil and then take up oxygen for root respiration, yielding energy for nutrient uptake, water for turgescence and transpiration and use in photosynthesis and the mineral nutrients needed for the synthesis of organic matter. Above the ground the plant takes in light energy and heat using them in photosynthesis to assimilate atmospheric CO2. Photosynthesis is the basic life process of creation. However, we will look at the root room where soil, water, air, and heat economy and the supply of nutrients determine soil fertility and the important role lime plays here. Location is the primary point to be considered when discussing agriculture (climate and soil); secondly, the dynamic and mobility of the minerals (plant nutrients) in the soil; and thirdly the conversion of organic substances into humus. And then there is a great deal of water involved in the growing process. In order to produce 1 kg of dry plant substance, 300 to 800 kg of water must be pumped through the plant and is then lost by transpiration. Cereals, vegetables, and sugar beets consume between 400 to 500 kg of water during the growing process and long-growing crops, such as alfalfa and clover, can consume 600 to 800 kg of water per kg of finished product. Without water, a plant cannot grow. (Reference 1)

Jan 1, 2006

By R Bresca, A McCallum, J Scealy

The Endeavor Mine, located to the north of Cobar, New South Wales, was purchased by CBH Resources Pty Ltd in September 2003. The operation has been producing lead and zinc concentrate continuously for over twenty-three years. In 2004, a water management program was instigated to improve the raw water use efficiency of the mining operation. The water management program involved the establishment of a Water Management Committee, a review and quantification of water use across the site, investigation and implementation of efficient water use practices, and workforce awareness training. The program has seen the amount of water used per tonne of ore milled reduced from an average of 1.08 kL/t in the March 2004 quarter, to 0.68 kL/t in the March 2005 quarter. This paper outlines the Endeavor Mine water management program and may serve as a model for other operations that are planning to improve their water use efficiency.

Jan 1, 2006

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By Z. W. Nkosi, M. Sephton, J. H. Potgieter

The exhaust system is a complex assembly of various components performing important tasks in harsh environments. Carbon steels have been used extensively in exhaust systems, but pressure for lower cost, increased fuel efficiency; lower hazardous emissions, weight savings and increased life expectancy have shifted the emphasis to stainless steels. In response to the growing consumption of stainless steels in automotive exhaust systems, the need to properly evaluate their corrosion resistance properties in order to ensure their appropriate use, has increased substantially. This paper evaluated the most common corrosion and oxidation tests developed that are used and applied it to four common stainless steels often employed in hot end exhaust components. In a summary considering the weight loss of an alloy, it general corrosion rate and pitting resistance under all the test conditions for hot end exhaust components, results indicate that 434 was by far the most corrosion resistant alloy, followed by 1.4509 and 321, and lastly 304 was the least corrosion resistant. In general, the ferritic stainless steels, especially 434, outperformed the austenitic ones under all the test conditions.

Jan 1, 2006

By D. J. Archambeault, A. Saigal

Substantial cost savings have been demonstrated by material design changes after initial product development. As more information about a product's operating environment becomes available to a designer, it is possible to consider a more costeffective material that still meets or exceeds the design intent, such as minimum low cycle fatigue life. This is especially true in the aircraft engine industry, where precise operating cycle data is not available until after the first engine is built and tested. A methodology for predicting estimated low cycle fatigue life has been developed to investigate potential material change candidates for an aft cooling plate. A twodimensional macromechanical finite element model (FEM) has been developed using ANSYS and used to determine the effects of varying material properties. It is shown that slight changes in density, coefficient of thermal expansion and modulus of elasticity have profound effects on component and effective stresses, and therefore, estimated low cycle fatigue (ELCF) life. Aerospace

Jan 1, 2006

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By P. A. Olubambi1

Representative samples of the hydrothermal vein deposits of the bulk complex sulphide ore deposit, 10 km south of Ishiagu, in Ebonyin State, South Eastern part of Nigeria were collected from two small scale mining companies. The samples were mixed and successively crushed in a jaw crusher and cone crusher, and ground in a rod mill. Characterization was carried out with SEM, EDX, XRD, XRF and ICP-OES. Mineralogical analysis revealed the presence of sphalerite, galena, siderite, pyrite, quartz and chalcopyrite. X-ray Diffractometry showed that sphalerite mineral in the ore occurs as sphalerite ferrous with varied percentage of Zn and Fe within the various sizes while chalcopyrite occurs as a chalcopyrite group mineral with chemical formula Cu2MnSnS4. Results of the elemental analysis showed variations in elemental composition within the different sizes.

Jan 1, 2006

By Huw Williams

It is becoming increasingly common practice to re-use existing foundations for new projects, especially on urban sites where geotechnical conditions are congested. A knowledge of the foundation dimensions and capacity is essential for this to take place, however, as-built records are often non-existent. Non-Destructive evaluation (NDE) is now becoming an important tool in assessing old foundation properties and their potential for re-use. Pile dimensions are also critical in the power industry, when they are supporting transmission towers which need to be upgraded, and may carry additional wind loading. This paper describes the application of various NDE techniques that are available and how they can be used to determine pile length, shape and capacity in difficult site conditions, including foundations under structures.

Jan 1, 2006

By D. G. Lee

Diesel particulate matter (DPM) often contains small amounts of metal as a minor component but this metal may contribute to adverse health effects. Knowledge of the mechanism for particle formation as well as the size preference of the trace metals is critical to understanding the potential for health concerns. To achieve this, the size and the composition of each particle should be optimally measured at the same time. Single particle mass spectrometer (SPMS) would be the best tool for this objective. In this paper, we therefore will introduce new findings about the mechanism and distribution of the trace metals in DPM, derived from a study where an SPMS was used to analyze freshly emitted DPM. KEY WORDS : Single particle mass spectroscopy, Diesel particulate matter, Characterization, Metal contents

Jan 1, 2006

By K. Adham

Iron chloride pyrohydrolysis (ICP) is used as an efficient way to fix iron as an oxide, for sale as a by-product or for safe disposal. Iron chloride is reacted with water at elevated temperatures to yield iron oxide and hydrogen chloride. Both the steel industry and synthetic rutile producers make extensive use of ICP. Two technologies are available for ICP: fluidized bed (FB) and spray roaster (SR). Both technologies are energy intensive. Here, fluid beds and spray roasters are compared with respect to their fuel and electrical energy consumptions. Roaster size and oxide product characteristics are also considered. Process models are prepared, using the METSIM® software, and specific energy consumptions are compared. The results will help the industry decide which technology best suits its goals and at what energy cost.

Jan 1, 2006

By C. Dupuis, P. Waite, S. Leboeuf

Casthouses throughout the aluminium industry commonly use chlorine gas as a fluxing agent for furnace and in-line treatment of molten aluminium alloys. Its positive impact on the removal of alkali elements and non-metallic inclusions is well known. Nevertheless, the elimination of its use is highly desirable due to the safety and environmental risks associated with storage and handling. Over the past decade, the aluminium industry has significantly reduced its chlorine consumption. This has been achieved by maximizing the chlorine gas utilization efficiency during metal processing, and by the chlorine replacement for crucible and furnace metal treatment applications. Operation of sealed in-line treatment units without chlorine is now possible, but with lower or inconsistent removal efficiency penalties for alkali and inclusions respectively. This paper reviews the progress made at Arvida Research and Development Centre regarding the reduction of chlorine and the development of an alternative to chlorine for in-line metal treatment without penalizing the metallurgical performance.

Jan 1, 2006

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By L. N. Ertzeva

The present work is dedicated to investigation of the sulfidizing process of ore pyrrhotite concentrate with recovery of a sulfide material, enriched with non-ferrous metals, and waste pyrite, with downstream separation by a certain beneficiation method.

Jan 1, 2006

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

In todayÆs demanding business landscape continual change and technological advancement is a given. With these changes there is now, more than ever, a need to ensure sustainable growth in respect of value protection and value adding whilst meeting the pressures and expectations of the societies in which we operate. Traditionally the management of safety has been a very reactive activity in the business, in some cases seen as an irritation and a disruptive process that demands a focus on preventing reoccurrences. This in turn has focused the measurement of safety performance on a range of lagging indicators û æafter the effect managementÆ. Gaining and maintaining a licence to operate is crucial to a sustainable business but as a prerequisite, organisations need to have a demonstrable ability to manage the safety of their people, as well as mitigating the people risk associated with the business activity. A major focus in the last decade has been on the implementation of enterprise risk management programs, where risk becomes embedded in all business systems and processes and the organisationsÆ genetic make up is programmed to analyse and integrate risk management into all facets of the business activity. The management of safety should be no different. One school of thought argues that there are no new accidents, but rather our inability to learn from the past. Others believe that as long as we have an appetite to achieve the unachievable, we will have to continue to push the boundaries, our safety comfort zones and inevitably take risks. Single reliance on highly evolved technical systems, elaborate processes, highly skilled people, safe equipment and safe work environments have shown one thing û they are not sustainable in providing adequate coverage in the business. In analysing a range of factors associated with some of the worst catastrophes of the 20th century, it can be suggested that they were in fact predictable and inevitable and that an integrated approach underpinned by sound risk management systems could have determined a different result. The key to a sustainable approach in the management of safety requires us to look at a multitude of aspects that collectively allow the performance of an organisation to be predictable. To have certainty in the business activities it is necessary to have controls in place that will mitigate the risks normally associated with unwanted events. It is ensuring that human factors effectively contribute to monitoring the planned approach and being able to safely adjust to any variability. In essence this is having the ability to proactively plan for the longer term. The sentiments articulated by organisational leaders echo that safety management is good business. Surely then a good business is a sustainable business, and a sustainable business is one that provides lasting benefits to its stakeholders.

Jan 1, 2006

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By Graham Davey

"Low speed stirred milling has been employed for many years in the metalliferous and industrial minerals industries. High speed stirred milling is a relatively new method of grinding in the metalliferous process industries. However it has been it has been in wide spread use in the industrial mineral field for over 30 years for various minerals. Many existing metallurgical operations are looking to maximize economic return from existing deposits, requiring new thinking and technologies. By combining low speed and high-speed milling fine and ultrafine grinding efficiency and operating costs can be improved.The correct selection of different fine grinding technologies is covered, when each mill is applicable and when a combination of the VERTIMILL® Grinding Mill and SMD provides the best economic solution.INTRODUCTIONUltra-fine grinding of minerals has been in wide spread use in the industrial mineral field for over 30 years. Within the last 10 years the metalliferous industry has shown interest in the ability to produce ultrafine particles, as chemical, physio-chemical and physical separation processes have advanced to be able to treat ultrafine metalliferous particles. Also as the primary mineral deposits, around the world are depleted, new more difficult deposits must be mined. Existing operations are also looking to maximize economic return from existing deposits, requiring new thinking and technologies.The traditional approach for gold containing refractory material has been to liberate the locked gold by chemically destroying the pyrite through oxidation. Roasting, pressure oxidation, and bacterial oxidation all employ various degrees of temperature, pressure and catalysis to react the pyrite with oxygen to produce iron oxide and sulfur by-products. However all of these methods are economically impacted due to specific operational added requirements and emissions controls. Pressure and bacterial oxidation have very high capital and operating costs."

Jan 1, 2006

By I. Mikov

Established in the 60-ies, the Zlatna Panega quarry is a cement raw materials quarry supplying 95% of the needs of the Zlatna Panega Cement Plant with limestone, marl and other silica-aluminates. The two major types of raw materials are formed by accordingly dipping strata of Upper Jurassic limestones and lower Cretaceous marls. Between them there is a ?transition-zone? or ?contact-zone? of a high-silica content layer, about 5-m thick, defined as ?flint? by investigations including spot sampling throughout the quarry. For many years this ?contact-zone? layer was neglected due its negligible thickness. Further, with the increasing demand on the quality of the raw materials feed to the Plant and the focus on variability of the chemical and mineralogical components, it was decided not to mine any of the parts of the quarry contaminated by this material, for about three years. The latter had an impact on the availability of operating benches that could result in a substantial decrease in the total recoverable re-serves of Zlatna Panega, particularly with respect to marls. There were considerations for resorting to a partial, selective excavation of the quarry pit with a reduced lifetime for the lime-stones and re-opening of an other (currently in-active) marl quarry at a distance of 6 Km from the Plant. The Quarry Team of the Zlatna Panega quarry was assigned to study the problem. The ?contact? layer was duly confirmed with systematic geological (including mineralogy) studies, statistical analysis of available data, surface sampling and shallow exploration drills, resulted into distinguishing a third type of reserves and their credible subsurface delineation by means of geological 3-D modeling and quarry design. A new quarry design was finally elaborated with a view of providing flexibility in mining, utilization of the total volume of all available reserves and maximizing the mine life of Zlatna Panega quarry. An industrial test took place in December 2005, by using the contaminated parts of the quarry (co-mining of the ?contact-zone? materials) at a contribution of 15-20% in the raw materials mix, as dictated by their contribution in the total recoverable resources of the quarry. The purpose was to investigate the viability of this solution ? in line with improved quarry planning ? without compromising the quality of cement production and the efficiency of Plant Operations. Results were overall successful.

Jan 1, 2006