Search Documents

By Y. Takasaki

For zinc hydrometallurgical extraction, reducing the electric power consumption of the electrowinning process is an important issue for energy savings. At the Zinc & Lead 2000 symposium, the authors suggested that by using the Pb-0.5%Ag-0.6%Ca alloy, the electrolysis energy can be decreased compared to the conventional Pb-0.9%Ag alloy. In this study, the corrosion behaviors of the Pb-Ag-Ca electrode in a sulfuric-acid electrolyte were investigated. Based on the results Or me Pb-0.5%Ag-0.6%Ca anode after 20 days of electrolysis, the bath voltage and the quantity of anode slime decreased compared to the Pb-I%Ag anode. Subsequently, beta-PbO2 on the electrode surface was detected by XRD and its peaks were sharper than the Pb-1 %Ag anode. Moreover, a dense beta-PbO2 layer on the 0.6%Ca a anode surface was observed. Therefore, it was suggested that the dense beta-PbO2 layer on the anode surface is one of the factors that leads to a lower bath voltage and decreasing quantity of anode slime.

Jan 1, 2003

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual' usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Jack A. Simon

My remarks are directed at relating some of the mineralogical approaches mentioned in the preceding presentations to emerging energy issues. The assembling of this symposium on process mineralogy attests to the growing concern for energy development from the non-petroleum mineral fuels and the unconventional petroleum fuels. A report in 1979, prepared under the auspices of the National Research Council/National Academy, of Sciences, was published in two parts and dealt with "Redistribution of Accessory Elements in Mining and Mineral Processing." This report rather comprehensively considers broad aspects of minerals associated with the solid fuels considered in this symposium and focuses attention on some problems of process mineralogy relative to these fuels. Papers have dealt with coal, oil shale, tar sands, and uranium minerals. Problems associated with mining, processing, and use of these materials have significant differences, but also have some factors in common relative to the subject of this symposium.

Jan 1, 1981

By Y. Shigeno

The reactivity of a porous solid is a strong function of its pore structure (porosity, pore surface area and pore size distribution). It follows that reactivity could be altered by altering pore structure; one way to achieve this is by chemical vapor infiltration whereby a gaseous species is reacted in the porous solid to produce a solid. Experiments were carried out in which the pore structures of various carbons were modified by cracking methane within the pores; oxidation rates of the carbons were then measured for both infiltrated and original samples. For coke it was found that two indices of coke performance used in the steel industry (CRI and CSR) can be greatly improved following a small amount of infiltration. Infiltration/oxidation results are interpreted in terms of measured pore structure changes.

Jan 1, 1993

By T. R. A. Davey

Previous publications on the application of EIETSIM include the modelling of an electrolytic zinc plant and a copper flash smelter. In the present case METSIM has been used to model the desilverising of lead by the reagent zinc, whereby a silver-zinc intermetallic compound is formed, and floats out of the lead. This compound has a variable composition, depending upon the ratio of dissolved zinc/silver in the lead bath. Its solubility in lead decreases with falling temperature. A number of variations and modifications of the Davey Desilverising Procedure are modelled, and applied to a wide range of silver contents in lead bullions at several plants. METSIM uses both feed- back and feed-forward controls to simulate plant conditions, and a logic control to distinguish between different phases in the Zn-Ag system. Use is made of extensive (previously unpublished) fundamental data on the ternary Pb-Ag-Zn system, and of plant data, to establish certain operating parameters.

Jan 1, 1993

By K. R. Robilliard

The Peru based tin mining company, Minsur S.A., commissioned Ausmelt Limited to design, supervise construction and commission a tin smelter and refinery for production of refined tin metal. The plant is located 240km south of Lima, near Pisco, Peru and is operated by Funsur S.A., the wholly owned subsidiary of Minsur S.A.. Selection of the Ausmelt Technology followed a series of crucible scale test work and pilot plant trials conducted at Ausmelt's facility in Dandenong, Australia and two feasibility studies undertaken by Ausmelt in 1991 and 1993. Ausrnelt began the plant design in 1994 with the construction phase following in 1995. Commissioning of the plant commenced early in 1996 with a target throughput of 30,000 tonnes per annum of concentrates. In mid 1998 oxygen enrichment of the Ausmelt lance air was introduced to expand the capacity to the throughput of 40,000 tonnes per annum of concentrates. The process route involves the use of an Ausmelt furnace for primary concentrate smelting, followed by a conventional tin pyro-refining circuit to produce high grade tin suitable for sale. Further work continues between Ausmelt and Funsur to investigate the use of an alternative, more economical, fuel source and the installation of a second Ausmelt furnace. The paper reviews the project to date with details of ongoing operations and developments at the Minsur Tin Smelter.

Jan 1, 2000

By Zhi-yong Liu

A novel process, which includes hydrochloric acid leaching, iron powder cementation, sulphide precipitation and spray pyrolysis, was proposed to treat iron concentrate recovered from zinc kiln slag for comprehensive utilization. Treated by two-stage hydrochloric acid leaching, the leaching extents of Ag, Pb, Cu, Fe and Zn are 96.78%, 95.14%, 97.72%, 94.51% and 87.74%, respectively. More than 99% Cu and Ag are recovered from the leach liquor when iron powder is 25% higher than the stoichiometric requirement. More than 96% Pb and Zn is removed with three times of theoretical consumption of FeS, and the concentration of impurities of the final solution is less than 500 mg/L. Fe2O3 powder, which is spherical with a mean size of 12 μm and purity of 99%, is prepared with final solution at 700 °C. In this process, not only the metal values can be recovered effectively, but also the iron resources of zinc kiln slag can be converted into high purity Fe2O3, thus, the comprehensive utilization of iron concentrate recovered from zinc kiln slag can be realized.

By D. Donald Downey

Pilot Testing Ion Exchange Resin (IEX) can go from very simple beaker testing to complicated column testing. Space velocities, regenerant quantities, loading capacities, ion leakage, are all terms that get accumulated together to prove or disprove a resin’s (or resins’) ability to load a single ion (or specific set of ions). Not getting all the resin’s operating parameters correct will disqualify (or at least skew) the results. Laboratory tests for capacity, moisture content, bead size, metals fouling, etc.—what does it all mean? At last count, there were over twenty-five separate ion exchange resin tests (analyses) that were available to end users. Standard testing procedures identify the resin properties but more specific procedures can be used to identify problems with equipment operation. Then, there are the costs to consider; simple cation resin testing (moisture content, total capacity and bead integrity) is in the $200/sample range. However, add to this Chatillon, Russian Ball Mill Test, HIAC particle size, metals and % regeneration test procedures and the lab work can increase to over $1000/sample. In this paper, the author will explain the “must-do” pilot and test procedures and why they are important and the key to understanding how resin performs ion exchange.

By Y. Prévost

The Noranda Continuous Converting Process was commissioned in November 1997 at the Home smelter in Rouyn-Noranda, Quebec, Canada. It has completed over 18 months of successful operation. Excellent team work and technical expertise contributed to achieve targeted production levels and environmental goals after only a few months of operation. The operating results have demonstrated the flexibility of the process in producing blister copper from a variety of copper feed materials including a combination of molten and solid copper matte, reverts and fluxes. This paper describes the startup activities and process optimization tasks performed during the first year of operation of the new Noranda Converter.

Jan 1, 1999

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By Pandey H. D.

The paper describes a fluidised bed ion exchange method for simultaneous removal of phenols and cyanide from the effluent. Use of an eluant enables regeneration of the resin in the continuous operation mode. The breakthrough experiments conducted both on the laboratory scale and on a pilot plant scale have shown that while the level of phenol can be brought down from 462 ppm to about 6 ppm, the free cyanide is almost totally removed. An examination of data indicates that the method can serve the twin objectives of pollution control and phenolic compounds recovery.

Jan 1, 1992

By Yasushi Sawada

An experimental investigation was carried out to study the rates of reduction of iron oxides dissolved in liquid Ca0-SO2-A203 slags by Fe-C droplets at temperatures ranging from 1325 OC to 1550 OC. The %FeO in the slag was varied from 5.5 to 18. Flash X-ray images were employed to observe the behavior of Fe-C droplets in the slags during the reactions and for determining the slag-gas-metal interfacial area. Effect of P205 in the slag and sulfur in the droplet was also investigated. The reduction rates were determined by measuring the volume of CO evolved as a function of time and the estimated slag-gas- metal interfacial area. The reduction rates have increased with increasing %FeO in the slag and the slag temperature. The experimentally established relationship between the reduction rates and FeO (wt%) in slag is given by

Jan 1, 1992

By Józef Czernecki

The Polish copper concentrates are characterised by low content of sulphur and iron. At KGHM Polska Miedz S.A. two copper production technologies are in use. The shaft furnace process is used at the Legnica Copper Smelter and the Glogów I Copper Smelter. A single-stage direct to blister Outokumpu flash smelting process is used at the- Glogów II Copper Smelter. Melting copper concentrates in the shaft furnaces is carried out in a reducing atmosphere and the product obtained is a matte. Instead, a result of melting copper concentrates by an oxidising flash process blister copper of a quality similar to that of converter copper is obtained. The annual copper production at KGHM Polska Miedz S.A. exceeds 450,000 tons. Another important metal is silver produced from slimes from copper electrolysis (about 1000 t/y). Moreover, such metals as Pb, Ni, Se, As, Au and other precious metals, including Pt and Pd, are recovered from various semiproducts. This paper presents technological flow sheet of the copper production in plants using the shaft furnaces and in another plant in which a single-state flash process is applied. Characteristics of products, methods of their utilisation, main parameters of particular technological operations, and advantages and shortcomings of the solution applied are presented. There are also discussed: the natural environment protection as well as directions of the KGHM Polska Miedz S.A. plants modernisation.

Jan 1, 1999

By John Wallace

"Monitoring compound semiconductor crystal growth using multifrequency eddy currents for sensing illustrates some of the extreme problems of measurement and interpretation that are not often seen in metallic systems. Using sensor arrays and scanning sensors have produced a qualitative and quantitative understanding of some of the high temperature electrical conductivity mechanisms in several compound systems. A detailed review of the CdTe/CdZnTe data is presented showing some of the complexity in the data as opposed to what is found in elemental semiconductors.HistoryThe most common goal in the use of eddy current measurement in crystal growth is to deter-mine the curvature of the liquid solid interface during growth to test if the heat transfer estimates of the thermal design were adequate for single crystal growth[l]. This aim could be met but represented only a small fraction of the data that was produced observing a growth cycle. A secondary consideration was what could be discovered in the recorded data about the growth and subsequent heat treatment as the boule cooled. This is usually a more difficult task because a crystal growth process is not a controlled experiment so much as a process that continually sees modification. Using a sensor arrays or a scanning loop has produced a qualitative and quantitative basis for understanding some of the high temperature electrical conductivity mechanisms. The implication of the these measurements of electrical conductivity variations are important in that they reflect the complex defect states that will occur on cooling and heat treatment following crystal growth. In contrast to the complex behavior of the conductivity of these compound semiconductors in the solid and liquid state we have the very well characterized system silicon to compare. Initially the interest on using eddy currents to monitor compound semiconductors came from G. Westphal at the Texas; Instruments Company in 1987 to monitor aspects of growth and compounding of GaAs. This was followed by work on solution growth of HgCdTe with D. Witter. The initial interest in the use of eddy cur-rents for monitoring CdTe crystal growth came from Prof. Wilcox at Clarkson University in the practical interest to determine and control the crystal interface curvature during vertical brigdeman growth. The first actual work was done by one of his former students. G. Neuge-bauer at the II-VI Corporation which was carried on by G. Rosen at Clarkson and R. Shetty at II-VI Corporation and with A. Socha at Johnson-Matthey Electronics. The work on CdTe extends over four years and yielded sufficient data to allow one to evaluate the utility of the information produced as compared to what could be obtained from monitoring an elemental semiconductor such as silicon."

Jan 1, 1997

By M. Shevchenko

Integrated experimental and modelling research program on the phase equilibria and development of thermodynamic databases of the lead and copper metallurgical gas/ slag-matte-metal-solids systems (PbO-“Cu2O”-FeO-Fe2O3- ZnO-CaO-SiO2) is being undertaken to support improvements in the pyrometallurgical smelting and recycling processes. This is the first systematic investigation of phase equilibria of slag systems in equilibrium with Pb metal, providing information for systems in which copper coexists in slag with lead or zinc as major components. The experimental studies involve high-temperature equilibration of synthetic samples, rapid quenching, and measurement of the compositions of equilibrium phases using electron probe X-ray microanalysis (EPMA). FactSage-based thermodynamic database development is integrated with experimental research. Initial thermodynamic assessments are used to identify priority compositions and conditions for experiments, which are planned to provide specific data to assist thermodynamic optimisation. Significant improvement in the accuracy of the phase equilibria description is achieved. Continuous database improvement and extension to include new elements are targeted. Example of industrial application is given.

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By B. Farouk, D. Apelian

"A numerical model has been developed to predict the temperature history of particles injected in a low pressure d.c. plasma jet. The temperature and velocity fields of the plasma jet are predicted as a free jet by solving the parabolized compressible Navier-Stokes equations using a spatial marching scheme. Particle trojectories and heat transfer characteristics are calculated using the predicted plasma jet temperature and velocity fields. Correction factors have been introduced to take into account non-continuum effects encountered in the low pressure environment. The plasma jet profiles as well as the particle/plasma interactions under different jet pressure ratios (from underexpanded to overexpanded) have been investigated.I. IntroductionIn the plasma spraying process a d.c. plasma jet is used as a heat source to melt and accelerate powder particles which subsequently impinge and solidify on a given substrate. During low pressure plasma deposition (LPPD) prooess, the plasma jet is expanded into a low pressure environment (40-80 Corr) which results in high plasma jet velocities with Mach numbers ranging from 2 to 3. Previous efforts to predict heat transfer and fluid flow in plasmas have made use of incompressible flow formulation employing turbulence models [1-3] for atmospheric plasma spraying. However, these theoretical calculations have been limited to the subsonic flow regime; hence, the compressibility effects and viscous heat dissipation were neglected. In the LPPD process, the plasma jet is operated at the supersonic flow regime, therefore, the compressibility effects and viscous heat dissipation are no longer negligible. This is the main motivation of this work.In addition, production of high quality dense deposits requires that a large fraction of the injected particles be in a molten state when they impact the substrate. An additional motivation for this work is that it is important to understand the plasma/particle heat and momentum transfer since these phenomena dictate both the particle thermal history and particle trajectory.Early computational works in supersonic nozzle field flow [4,5,6] consisted of patching methods that divided the flow field into an invisoid free stream and a viscous boundary and. mixing layers. Each was analyzed independently and coupled through appropriate boundary conditions. Later schemes [7,8] involved solving time-dependent, compressible Navier-Stokes equations over the entire computational domain. These schemes show a great promise in predicting flows with complex structure, and where the viscous effects became prevalent."

Jan 1, 1986

By R. Parada

A real-time dynamic simulation model has been developed to characterise the flash furnace operation at the Chagres smelter. This model permits the operators to plan the process to meet the Peirce Smith converters' schedules and feed the acid plant with gases that satisfy its best operating efficiency range. Essential control parameters for the furnace (process air enrichment, oxygen coefficient and supplementary heat) are calculated to satisfy process targets such as matte grade, slag silica and matte/slag temperatures. These calculations are carried out with a real-time simulation. Flash furnace control and operational stability permits setting up control strategies that streamline the flow of copper to converters and of sulphur to the acid plant.

Jan 1, 1999

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By Jose Carlos D’Abreu, Edelink Efrain Tinoco Falero, Mauricio Marcos Otaviano, Helio Marques Kohler

Nowadays the most important Direct Reduction - DR processes in shaft furnaces has to deal with carbon fines precipitation and DRI carburization issues. Based in a cooperative research program joining Catholic University (PUC-Rio) and SAMARCO Mining Co, a project dealing with pellets reduction and those two phenomena was established. This work analyzes kinetically the three reactions mentioned before, considering typical values for the operational variables temperature, flowrate, pressure and gas composition, parameters commonly used to control the DRI formation in the Reduction Zone - RZ of the shaft furnaces. From laboratories experimental results, the kinetic equations for those reactions were established and, using the superposition principle, generated a specific global kinetic model for the iron oxide reduction and the soot formation. Finally, using those experimental results and applying a planned statistical factorial analysis for the experiments, the numerical coefficients for each equation were calculated and the correlation factor determined for the proposed global kinetic equation.

Jan 1, 2015