Search Documents

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By Wen Chen, Xinghua Liu, Zeyou Peng, Qiulin Wang

"Limonite is a collective for iron hydroxide argillaceous materials. It is very difficult to be treated due to the wide variation in specific gravity and magnetism and the high argillization rate in the course of grinding and beneficiation. The iron ore in Huangmei, Hubei, China is the typical representative of limonite. If the limonite is processed using conventional physical beneficiation methods (e.g. magnetic separation, gravity separation, flocculation-desliming-flotation, or a combined process of the three), it can only be obtained an iron concentrate grade of 51.98% and an iron metal recovery of 86.64%. However, the technique of flash magnetic roasting-magnetic separation can improve the concentrate grade to 61.03%, iron recovery to 91.17%. This paper describes the tests of recovering limonite by flash magnetic roasting in detail.IntroductionLimonite (mFe2O3, nH2O)[1] is a general designation for hydrous iron hydroxides and argillaceous matters. Limonite is hard to be separated because of its complicated geneses, comparatively weak magnetism, nonuniform grain size and being easily slimed during grinding. So most small and medium enterprises sell deslimed limonite product which was dealt with just by simple methods of washing, magnetic separation or gravity separation and so on. In recent years with the iron ore prices soaring, significant progress was made in mineral processing research of limonite. Laboratory research and industrial test results showed that flocculation-desliming-flotation process and roasting-magnetic separation process are the two best methods to recover limonite till now. To compare these two methods, roasting-magnetic separation process is superior to flocculation-desliming-flotation process in aspects of beneficiation indexes and industrial stability."

Jan 1, 2012

By Qiang Zhong, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

Viscosity of slag determines the production efficiency, energy consumption and distribution of elements between metal and slag, which is very important for pyrometallurgy. Slag of goldantimony ore blast furnace smelting has seldom been studied. In this paper, the viscosities of gold-antimony ore smelting slags of different composition have been studied by the rotating cylinder method. The results showed that, for a slag of 38.95% SiO2, 16.17% CaO, 25.97% FeO, 10.25% Al2O3, 5.17% MgO, the viscosity can be decreased by reducing 3.24%-8.5% SiO2 or increasing 3.31%-9.56% CaO content. Complex SixOy z- from SiO2 acts as the main cause for the high viscosity in a slag of high SiO2. The increasing of CaO causes the decreasing of the amount of SixOy z- and the O2- dissociated from CaO breaks the complex SixOy z-, which can decrease the viscosity. Viscosity of different composition slag in the appropriate range temperature can be calculated from the Arrhenius equation.

Jan 1, 2015

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By Cajsa Samuelsson, Theo Lehner

Converting and refining play a central role in the extraction of metals. Sweden has a long tradition as an experimental play ground for metallurgists, chemists and alchemists, developing new methods and technologies. Presenters of papers are usually happy in recording successful developments. But reporting failures can be as great a value as the former. In the paper experiments and experience in process development are illustrated, differences between ferrous and non-ferrous developments are highlighted and industrial learning curves are discussed. 53

Jan 1, 2009

By Hongbo Zhao, Jun Wang, Wenqing Qin, Guanzhou Qiu, Xueduan Liu

Bio-hydrometallurgy technology was applied for the extraction of copper from the raw ores of Chambishi Mine in Zambia. A copper extraction of 93.29% was obtained for small scale column bioleaching within 63 days, while a copper extraction of 89.05% was achieved for large scale column bioleaching in 90 days, thus confirming the amenability of the raw ores for effective extraction via bioleaching. The bacteria were cultured in a 6-stage enlarge cultivation. The bacterial cultures with cell concentration of more than 1×108 cells/mL were added into a spray pond of sulfuric acid to be applied in the dump leaching, and a copper extraction of about 50% was achieved within 2 months. The production report revealed that the copper extraction increased by approximate 20%, and the acid consumption was reduced to around 35% as a consequence of adding the bacteria. The industrial demonstration of the bio-hydrometallurgy technique is now well established in Zambia, and further applications of bio-hydrometallurgy in both Zambia and Congo are currently in progress.

Jan 1, 2015

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By Y. Yang, S. Peelman, J. Sietsma, Z. H. I. Sun

The rare earth elements (REEs) present in the Kiruna iron ore mine tailings are being considered as a new REE resource for the EU. These tailings, after beneficiation, contain approximately 5000 ppm of rare earths, concentrated in apatite and monazite minerals. To economically extract the REEs from these tailings the phosphorous contained within the apatite must also be extracted and the waste production of the process should be minimal. To achieve the extraction of REEs and phosphorous HCl and HNO3 were investigated as possible leaching agents. Based on the results a leaching process using HNO3 is proposed. This process produces H3PO4 from the apatite while simultaneously dissolving the REEs. The resulting leach liquor is then cooled to remove the unwanted Ca as Ca(NO3)2. Analysis of the leach liquor reveals extraction ratios of between 75% and 100% for the heavy REE (e.g. Y, Eu, Dy, …) and below 40% from the light REEs (i.e. Ce, La). Full phosphorous extraction was also achieved.

Jan 1, 2016

By Willy Persson

A common feature of the kinds and amounts of impurities present most pyrometallurgical, processes is injection of oxygen to, remove various in the feed. The degree of success of a specific process step relies critically on control of the instantaneous oxygen potential/oxidation stage, throughout the step as well as upon termination of the step. This will, for instance, determine the distribution of impurities between metal and slag. As long as the operation is perturbation free -detailed analysis of all additions and application of advanced models often yield satisfactory control means However, a pyrometallurgical process is seldom free from disturbances, which reduces the accuracy of the static models and leads to inconsistencies in scheduled route might be uncontrollable changes in quality and quantity of feed, operator interventions and shift changes, timing of cranes, lining wear and accretions etc. The implementation of dynamic, control to correct for disturbances and, more generally for process optimization, requires continuous on-line information on, the actual status of the process. The implementation of sensors for continuous process monitoring, e.g., as regards the instantaneously prevailing oxygen potential or oxidation stage, has been hampered by the highly aggressive environment in smelters; This is. where remote-sensing techniques based on optics and spectroscopy, have proven to form invaluable, tools towards the realization of dynamic production control. Since about 15 years Semtch has developed and industrialized a remote-sensing technology, based on ,optics and spectroscopy, for continuous on-line process monitoring and production control of various pyrometallurgical processes. The presentation will discuss applicability aspects with examples and experiences from installations and tests in ferrous and non-ferrous industry. Keywords: Applied spectroscopy, Metallurgy, Process monitoring, Production. Control

Jan 1, 2003

By Kotaro Ogura

"Ethylene has been produced in aqueous solution from CO2 by the electrochemical reduction driven by a natural energy. This process is useful for storing a large amount of the natural energy. In the closed system, the conversion efficiency of CO2 is almost 100%, and the maximum selectivity for the formation of ethylene is more than 70%. On the other hand, the current efficiency for the competitive reduction of water is less than 10%. The electrolysis is practicable under such special conditions as three-phase interface consisting of gas, solution and metal, concentrated solution of potassium halide, low pH and copper or copper halide-confined metal electrode. These requirements are thoroughly examined, and the grounds to reply upon are revealed. A series of chemical apparatuses including an electrolytic cell in a large scale are designed for the ethylene production, which allow us continuously to supply raw CO2 and to extract the product.IntroductionIn connection with the depletion of the petroleum reserve, much attention has been paid to the utilization of natural energies such as sunlight, wind force and waves. However, these energies are always changeable, and some means of storing them are necessary for the common use. In general, natural energies are transformed to the electric energy at the time of utilization, but the electricity is not very storable. This is one of the reasons why the application of natural energy is not so expanded. On the other hand, the storing of natural energy by plants is very skilful. In the photosynthesis, solar energy is transformed to chemical energy by fixing carbon dioxide."

Jan 1, 2009

By Carvalho A. Felipe de

The search for environmentally friendly and cost-effective methods for gold extraction has been undertaken in order to provide alternatives to the use of cyanide leaching in the gold industry. Among such alternative reagents is the combination of chloride and hypochlorite ions due to their oxidation of metallic gold and its complexation. Therefore, the current work aims at investigating gold leaching from an oxidized material by means of a solution comprising calcium hypochlorite and sodium chlorite. The sample used in the current research contained 66.1% Fe2O3, 20.4%SiO2, and 35.7 g/t of Au. In addition, XRD and SEM-EDS analysis revealed iron oxide, quartz and muscovite as the main crystalline phases in the sample. For comparison purposes, cyanidation of the oxidized material resulted in 90% gold extraction in 24 h. The reference conditions for the leaching tests with the chlorite-hypochlorite system were: particle size −37 μm, solid/liquid ratio of 10% (w/v), 10 g/L NaCl, 10 g/L Ca (OCl)2, pH 5–6, 3 h of leaching. The effects of the: (i) Ca(OCl)2 concentration, (ii) NaCl concentration, (iii) pHrange and (iv) the effect of pulp density in the extraction of gold were assessed. In addition, the stability of the hypochlorite solutions (OCl−) was investigated. The ideal concentrations of Ca(OCl)2 and NaCl were determined as 25 g/L and 15 g/L, respectively, whereas the optimal pH range was 4–6. Under these conditions, the final gold extraction reached approximately 84%. By varying the solids content of the pulp (10%, 20% and 30%), it was observed that the lower solids value resulted in greater gold extraction (84%). The degradation of the hypochlorite solution and the possible catalytic effect of the presence of the solid were evidenced. To sumup, in the experiment, high gold extractions were achieved in shorter periods of time (3 h), as compared to the cyanidation of the same sample. On the other hand, itwas necessary to use significant amounts of the reagent due to hypochlorite instability at the pH conditions recommended for high gold extractions.

By S. G. Kumar

The performance of nickel based high temperature materials is directly related to their microstructure, which is controlled by the various processing steps. Nickel base alloys are melted and refined by a variety of processes that include Vacuum Induction Melting (VIM), Vacuum Arc Remelting (VAR) and Electroslag Remelting (ESR). The limitation of VIM is that the metallrefractory reactions lead to the disintegration of the crucible and hence contamination of the product due to macrosegregation. This macrosegregation is alleviated to some extent by controlling the solidification in VAR. The main attraction of ESR is its ability to produce a clean product by controlling the deleterious inclusions. In recent years Electron Beam Melting (EBM) is emerging as an alternative to the VIM, VAR and ESR. This paper reviews the current status of these processes and outlines the scope for further improvements in the processing technology.

Jan 1, 1993

By Leo Brewer, Kazuyoshi Shimakage, Mamoru Mitomo, Toshiyuki Nishimura, Yoichiro Uemura, Shinji Hirai

"In the synthesis process of ß -La2S3 via the sulfurization of La2O3 powder using CS2 gas, La2O2S was formed. This occurred at an initial stage of the reaction for sulfurization temperatures below 973K, and ß -La2S3 was also formed at a shorter period for higher sulfurization temperatures. It was found that the oxygen content in ß -La2S3 powders decreased gradually with an increase in sulfurization temperature. On the other hand, the carbon content in these powders increased gradually with an increase in the sulfurization temperature. Though it has been reported that ß -La2S3 was transformed to Y -La2S3 at 1723K± 50K, the sintered compact of double-phase Y -La2S3 and ß. -La2S3 was formed at a rather higher temperature of 1973K when the synthetic powder of ß -La2S3 containing a high amount of oxygen was used. However, phase transformation of -La2S3 to Y -La2S3 progressed preferentially with a decrease in the oxygen content of synthetic ß -La2S3 powder. The Seebeck coefficient of the sintered double-phase Y -La2S3 and -La2S3 was higher than that of the single-phase Y -La2S3, reported previously.Introduction La2S3 exists in three polymorphic forms that are similar to a series of Ce2S3, Pr2S3 and Nd2S3: a, ß , and Y'. The a -La2S3, which is stable at low temperature, is irreversibly transformed to ß -La2S3 of various compositions in the solid-solution range between La2S3 and La3S4, at 923 ± 50K. The -La2S3 may also be an oxysulfide of La10S14O2. Moreover, the ß .-La2S3 phase is transformed to Y -La2S3 ,which has a Th3P4 structure, at 1573 ± 100K. The melting point of Y -La2S3 is 2398 ± 30K where this temperature is similar to those of common refractory materials such as silica and alumina. Therefore, it can be predicted that y -La2S3 which has a high melting point and a thermodynamic stability due to the strong affinity of La for S, would have &high refractory character and chemical inertness in many molten metals. The y -La2S3, colored vivid faint yellow is stable up to 623K in air, where oxidation starts. y -La2S3 is frequently used as pigments for plastics and paints3. Furthermore, Y -La2S3 which is a semiconductor, is considered to be useful as a thermoelectric conversion materials, because it has a high Seebeck coefficient."

Jan 1, 2000

By J. Murdoch Mackenzie

Two commercial nickel solvent extraction plants treating laterite leach solutions and using LIX®84-I have been operated in Australia. These circuits employ similar extraction chemistry but differ in their leaching and stripping operations. An alternative process involving elements of both can be conceived. The preparation of the feed solution to solvent extraction plays an important role in nickel extraction using LIX®84-I and the special features of manganese removal and cobalt oxidation in the preparation of the PLS are discussed. This paper compares these three circuit configurations with special reference to the extraction and reductive stripping of cobalt, the transfer of zinc and copper to the strip aqueous, ammonia transfer and sulfur transfer. The potential degradation of the organic and remediation using re-oximation is discussed. Keywords: Nickel, Solvent Extraction, Oxime

Jan 1, 2004

By Nagy El-Kaddah, Thinium T. Natarajan

A modeling strategy is presented for computing the electromagnetic field and the shape of the molten metal in electromagnetic confinement systems. This strategy involves the use of a hybrid finite element/integral technique to calculate the electromagnetic field and force distribution in the melt. The free surface shape is determined from minimization of electromagnetic, gravitational and surface tension energies using the Lagrange method of multipliers. This approach was applied to model the electromagnetic levitation melting process. The model was found to accurately predict the measured shape of levitated droplets.

Jan 1, 2014

By N. El-Kaddah, J. W. McKelliget

"A mathematical model for the analysis and design of hybrid plasma reactors for advanced materials synthesis is presented. The model is based upon a solution of the electromagnetic vector potential equation and is capable of predicting the two-dimensional velocity, temperature, and electromagnetic fields as well as the reaction kinetics inside the reactor for any axi-symmetric coil configuration. The model is used as a computer aided design tool for the design of hybrid plasma reactors consisting of a conventional DC torch augmented by an RF induction coil and it is demonstrated that the hybrid system possesses superior characteristics for materials synthesis over conventional DC or RF systems. The coupling between the RF and DC components is found to affect both the temperature field and the flow field and to have a significant effect on the reaction kinetics and on materials recovery. The model is used to study the thermal decomposition of silicon tetrachloride as a function of reactor design and operating parameters and it is demonstrated that through a CAD approach it is possible to significantly improve the operation of materials synthesis systems.IntroductionIn recent years there has been growing interest in the use of the inductively coupled plasma for chemical synthesis as a way of meeting the increasing demand for high quality, high performance materials for use in critical applications/l/. Although the basic feasibility of this approach has been demonstrated in the laboratory/2,3/ there still exists a number of operational problems that adversely affect system performance for some applications. In particular, the recirculation and back flow effects that arise from the electromagnetic forces in the plasma can result in the repulsion of the reactants from the hot plasma core and their subsequent deposition on the walls of the reactor. Another operational problem arises from the fact that the energy dissipated in the plasma has to compensate for the heat losses to the environment by conduction, convection, and radiation in order to maintain the ionization of the plasma and, hence, the stability of the plasma may be affected by the presence of the reactants and their products."

Jan 1, 1988

By Paul L. Wichlacz

A mathematical model of growth and ferrous iron oxidation for attached bacteria was applied to rotating biological contactor (RBC) units treating acidic mine drainage. The model describes attached bacterial growth as a saturation function, where the rate of substrate utilization is determined by a maximum substrate oxidation rate constant, a half saturation constant, and the concentration of substrate within the RBC. The maximum oxidation rate constant was proportional to flow rate and the substrate concentration in the reactor varied with influent substrate concentration. The model was tested at three separate sites and with three different size RBC units. The ability of the model to predict the rate of iron oxidation under all test conditions was significant. The accuracy of the model was found to be affected by unit size and vary with specific test site.

Jan 1, 1985

By Masaru Tomoguchi, Tom Nishiyama, Naoto Sasamoto

"In Hanaoka Mine, which was one of the major ""black ore"" (Kuroko) mines in the north part of Japan, mining has finished in 1994, and only mineral processing plant is available now. Recently this mineral processing plant has been applied to the soil washing. Soils contaminated with heavy metals are excavated and transported to the plant. The soils are separated to cleaned soil and metal enrichment through the process which consists of scrubbing, classification, extraction, insolubilization, flotation, and so on. The process is flexibly designed for each contaminated soil, in order to the products can be recycled as cleaned soils or metal sources. . Soils contaminated with arsenic and lead were treated in 1999, which were entrusted from Environmental Agency of Japan.IntroductionDowa Mining has had the mine site named ""Hanaoka Mine"" and ""Kosaka Mine"" in the north part of Japan. Those mines consisted of some ore deposits and produced ""black ore"" (Kuroko) and ""yellow ore"" (Oko), which are complex sulfide ore. The ""black ore"" mainly consists of sphalerite, galena and barite with accessory chalcopyrite, tetrahedrite and Au, Ag minerals. The ""yellow ore"" mainly consists of powdery and clayey ore containing chalcopyrite and. pyrite, with a little sphalerite and galena. Each mine site had mineral processing plant respectively, ""Hanaoka Mine"" had two and ""Kosaka Mine"" had one plant. Those plants were operated by flotation process to separate each mineral, and produced concentrates of copper, lead, zinc, pyrite, barite and so on.Unfortunately, the mine had closed one by one because of change in economical circumstances and the lack of ore reserves. Mill plants were also closed and dismantled, but the last ""Matsumine mill plant"" of Hanaoka Mine was remained to be utilized usefully. In the circumstance like that, we came across with soil remediation business. Recent reports say that subsurface contamination in Japan is being grown substantially and that it can be a serious matter beyond the imagination of our society. So nowadays we have a tendency to pay attention to the environmental issues including subsurface one."

Jan 1, 2000

By Junmo Ahn

This study investigated leaching kinetics by alternative lixiviants for copper leaching from chalcopyrite (CuFeS2), the most abundant copper resource in the world. As a refractory sulfide mineral, chalcopyrite shows low copper extraction due to passivation on chalcopyrite surface. Also, decrease of copper grade with high portion chalcopyrite requires the alternative leaching procedure to increase copper recovery. Therefore, alternative lixiviants such as sulfurous acid and methanesulfonic acid (MSA) were tested for both concentrate and low grade ore to enhance copper extraction. Also, an oxidant, hydrogen peroxide, was compared to ferric to find out the improvement of leaching kinetic. In concentrate leaching tests, 30 g/L MSA showed the highest copper extraction (47%), compared to other lixiviants at 75 °C. Periodical H2O2 addition enhanced copper extraction, and above 90% of copper extraction was observed within 96 h by periodical addition of 0.6% H2O2 at 75 °C. The activation energy of chalcopyrite leaching by MSA and H2O2 achieved 40 kJ/mol, which is chemical reaction control. The results of low grade ore leaching tests indicates that no significant difference among lixiviants (H2SO4, H2SO3 and MSA) with ferric was observed, all of which achieved around 37% within 24 h at room temperature. However, significant increase of copper extraction (>80%) was observed at both 20 g/L MSA and 10 g/L H2SO4 conditions by the addition of 10% H2O2.