Search Documents

By M. Waladan

The top submerged lancing Sirosmelt system has been developed through laborator.y scale testwork and pilot plant trials for recovery of zinc from ISF slag. The effects of the process variables of gas injection rate, method of coal feeding, and temperature on zinc fuming rates were studied in the laboratory. It was found that the rate of zinc elimination was dependent on all of these variabl.es. The rate of zinc removal from slag was independent of zinc content of slag down to approximately 1.5% Zn, below which the rate was proportional to zinc content in slag. Pilot plant trials were carried out to evaluate a proposed process and results followed predictions from the laboratory scale tests. A comparison of the proposed process with conventional slag fuming operations is made and it is shown that the process has a number of advantages which have a significant impact on the economics of zinc slag fuming.

Jan 1, 1990

By Li Ma, Shaoguo Chen, Gele Qing, Qihang Liu, Keng Wu

Olivine contains higher MgO element, which can be added into blast furnace burden to improve slag stability and fluidity. Effect of calcined olivine and untreated olivine on low silicon pellet production process and quality was studied in this paper. The results shows, calcined olivine has no effect on bursting temperature of green pellet, however the bursting temperature of green pellet will decrease with increase of untreated olivine ratio. Untreated olivine has slight effect on green pellet strength than calcined olivine while the ratio is higher than 2%. The compressive strength of low silicon pellet will increase first and decrease afterwards with increases of calcined olivine ratio under firing temperature of 1250°C, whereas, the changing sequence is reverse fired under 1280°C. The result of untreated olivine pellet compressive strength is same as calcined olivine pellet. However, the compressive strength and metallurgical property of calcined olivine pellet is slightly higher than that of untreated olivine pellet under same condition.

Jan 1, 2015

By J. V. Atwood

The U.S. Bureau of Mines has developed a novel Double Membrane Electrolytic Cell (DMEC) that exhibits unique features for recycling contaminated metals and metal alloys. The DMEC incorporates two anionic ion exchange membranes, separating anodic and cathodic regions of the cell. The ion exchange membranes prevent significant transport of unwanted cationic impurities to the catholyte from the impure anolyte while the anion/cation balance in cell compartments is maintained through the free movement of anions between compartments. The membrane barrier makes it possible to electro refine highly contaminated materials or to electrowin from solution while utilizing alternate anode reactions. Sinceanolyte and catholyte cross contamination has been eliminated, premium cathode products are produced. The DMEC has been tested at bench, pilot, and commercial scales. Configuration of the DMEC, cell operation, scale, up efforts, and significant design factors are discussed. Two separate recycling investigations utilizing DMEC technology are presented. The first investigation examines recovery of high purity cobalt and nickel from severely contaminated super aIloy scrap. The second involves? upgrading contaminated cobalt in the U.S. Government's National Defense Stockpile. Capital and operating costs for both potential applications are presented.

Jan 1, 1995

By R. A. Spitz, R. Leiby, M. Bricker

Electrochemistry plays a significant role in minimizing wastes at East Penn's secondary lead smelter. East Penn has been recovering spent battery acid for reuse in new batteries since 1992. East Penn also produces a fertilizer feedstock from sulfur dioxide in the smelter stack gases. The success of these processes is, in large part, due to the installation of electrochemical cells. The cells in the acid recovery plant allow the waste from this process to be concentrated into less that 10% of the original spent acid. The cells in the fertilizer plant treat the solution to remove dissolved metals prior to sale to fertilizer manufacturers.

Jan 1, 2000

By H. D. Freeman

The occurrence of gold in refractory gold ores varies widely and affects the recovery process. The determination of gold and the composition of the associated minerals are important in selecting an appropriate processing scheme. However, locating the gold in an ore sample is a difficult task which requires perseverance, luck, and experience. Our experience has led to the development of a relatively fast and reliable means of deter-mining the mineralogy of ore samples through analysis combining an energy-dispersive x-ray analyser coupled to a scanning electron microscope (SEM). In some cases, a wave length dispersive spectrometer or microprobe is used to further quantify the various mineral compositions. The SEM/microprobe analysis identifies the source of problems that may arise during the recovery of gold from refractory gold ores.

Jan 1, 1981

By J. R. Bhamidipati, Nagy EI-Kaddah

"Over the years, mathematical modeling has been established as a viable tool for design and analysis of melting and solidification processes. Modeling of electromagnetic casting and melting systems involves three coupled problems -- determination of the containment field, the shape of the meniscus, and the temperature field -- which have to be solved simultaneously. One of the difficulties in numerical simulation of these systems is in defining and gridding the solution domain as the meniscus shape of the liquid region is not known a priori. This paper describes a methodology for solving these coupled problems in a two-dimensional electromagnetic containment field. This method is based on the solution of the electromagnetic, free surface dynamic, and heat transfer equations in a fixed domain in computational space by mapping the physical space into an invariant computational space during the search for the equilibrium shape using a variable non-orthogonal coordinate transformation. This approach, also, eliminates the need for regridding the liquid and solid regions during phase change. This methodology is demonstrated for two electromagnetic confinement systems -- the Magnetic Suspension Melting process and the electromagnetic casting of aluminum. The model predictions are in good agreement with available data for these systems. It is suggested that the methodology presented here is likely to provide a useful tool in the design, analysis, and optimization of electromagnetic confinement systems. IntroductionDuring the past decade, mathematical modeling has emerged as a viable tool for the design, analysis, and optimization of casting and melting processes /1-2/. It is generally recognized that the usefulness of modeling to study the interplay between the various process parameters without resorting to extensive experimentation relies heavily on accurate representation of the physical phenomena in these systems. In modeling electromagnetic confinement casting and melting systems, it is important that the model address all aspects of electromagnetic field interaction with the metal, if accurate predictions are to be obtained /3/. The electromagnetic field affects the heat transfer phenomena primarily through joule heating. In addition, the electromagnetic forces play a key role in heat redistribution in the molten pool via melt stirring, and, in confinement systems, support the molten metal pool."

Jan 1, 1994

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro

"Jute fibers have in the past decades being investigated as possible reinforcement of polymer composites. However, information is still needed on the fiber interaction with a polymeric matrix for a complete evaluation of the capacity of load transference inside the composite. The present work investigated the interaction of jute fibers with polyester matrix by means of the critical length assessment through pullout tests. Tensile tests of polyester sockets embedded with different fiber lengths allowed the critical length to be determined and then the interface shear stress to be calculated. A relatively low interfacial strength was found, which indicates a weak adhesion between the ramie fiber and the polyester matrix. The SEM analysis of pulled out fibers corroborates this result.Introduction Natural fiber, mainly those lignocellulosic extracted from plants, have, in the past few decades, attracted the attention not only of scientists but also of industrial technologists of our society interested in their engineering applications. As it is well known, uses of natural fiber in clothes carpets, baskets, ropes and low cost construction roofing has existed from the beginning of our civilization. Today environmental and energy saving issues are motivating research works on new uses of lignocellulosic fibers in polymer composites [1-6]. Moreover, industrial application of lignocellulosic fiber composites are already in technological sectors such the automobile industry, packing and civil construction [7-9].In addition to environmental, economical and social benefits, some lignocellulosic fibers present specific properties that are comparable to those of other synthetic fiber used for polymer composite reinforcement. For instance, the specific strength (GPa.cm3/g) of curaua (1.31), sisal (0.92) and ramie (0.93) fibers, from results obtained with very thin diameters [10] are relatively closer to that of glass fiber E (1.33). Therefore, in principle, it would be technically justified to replace glass fiber, which is more expensive, toxic and represents a problem to the environment [ll], by a strong lignocellulosic fiber. However, serious drawbacks such non-uniform dimensions and heterogeneous properties [6] as well as the tendency to form aggregates during processing and incompatibility with a hydrophobic polymer matrix, reduce the potential of lignocellulosic fiber to be used as composite reinforcement [1-6]. In particular, a low interfacial strength causes a weak adhesion between the hydrophilic fiber and the polymer matrix."

Jan 1, 2011

By G. Upadhya

Of late, solidification modeling has progressed considerably to emerge as a viable simulation tool for the foundry engineer. A wide variety of tools exist in the commercial market to cater to the various needs of the design/ foundry engineer. In fact, recent developments in the area of solidification modeling have been so rapid that a comprehensive review of the state-of-the-art is very much needed. In this paper, an attempt is made to summarize the various issues of solidification modeling, at the same time addressing the historical evolution of the subject. The various phenomenological issues covered in this paper include: heat transfer, fluid flow during mold-filling, solidification kinetics and microstructural evolution, quick-analysis schemes for approximations, porosity prediction models, and the phenomena of fluid flow in the mushy zone. Modeling issues related to the development of solidification stresses which lead to defects such as hot tears and the development of artificial intelligence concepts in the area of rigging design are also discussed. Due emphasis is given to the various phenomena which add to the complexity of the whole subject, and the various alternatives available for solving a particular problem. For example, the heat transfer problem can be approached by the use of simple modulus schemes or by solving the conduction equation to obtain a more accurate temperature distribution. Similarly the microstructural evolution can be handled in a deterministic way by use of nucleation and growth models, or in a probabilistic way by use of empirical models. The main goal of this paper is to put the multi-faceted problem of solidification modeling in proper perspective so that it can serve as a guide for future developments in this area.

Jan 1, 1994

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By R. J. Kuczynski

The U.S. Bureau of Mines Reno Research Center operated a batch pilot plant to demonstrate high-temperature cyanide leaching for recovering platinum group metals (PGM) from automobile catalysts. Approximately 1,600 kg of used pellet, monolith, and metal support catalyst containing 1,680 g (54 tr oz) of PGM were processed. Forty-five-kilogram batches of used catalyst were leached with sodium cyanide solution at 160° C for 1 h under basic conditions in a countercurrent processing sequence to dissolve the PGM. Extractions from the used pellet catalyst ranged from 94 to 95 pct for Pd, 95 to 97 pct for Pt, and 64 to 81 pct for Rh. Extractions from the used monolith catalyst ranged from 7B to BB pct for Pd, 75 to 90 pct for Pt, and 43 to 71 pct for Rh. Heating the pregnant leach solutions to 275' C for 4 h destroyed the PGM-cyanide complexes, resulting in over 99.7 pct of the PGM precipitating from solution. The PGM precipitate was predominantly a powder metallic concentrate, typically analyzing greater than 50 pct PGM. Heating destroyed cyanide to less than 0.2 mg/L. Both the pellet and monolith residues were evaluated for disposal using the EPA Toxicity Characteristic Leaching Procedure.

Jan 1, 1995

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

By Kimio Itagaki, Torn Matsumoto, Makoto Ohtsuka, Kentarou Harada

"The structure and hydrogen-absorption properties of LaNis thin films were investigated in the present study. LaNis thin films were prepared by a sputtering method with a radio-frequency power, Ws, of 50 -400 Wat substrate temperature, Ts, of323 -573 K. Nickel content of the films decreased with increasing Ws, however, there was no dependence on Ts. At low Ws and low Ts, amorphous films were deposited. In other conditions, the films were polycrystalline. The films prepared at high Ws and low Ts, or at low Ws and high Ts, exhibited only a (h k · 0) peak in the X-ray diffraction profiles. This indicates that the c-axis of crystalline films was oriented parallel to the substrate plane. At high Ws and high Ts, the films with columnar structure were obtained. Hydrogen-absorption capacity of the thin films increased with increasing Ws. The pressure plateau did not appear on the pressure-composition isotherms. The films deposited at high Ts represented a higher equilibrium pressure.IntroductionThin films of hydrogen storage alloys can be applied for an electrode of rechargeable battery or fuel cell, a filter for H1 purification and various kind of sensor. Some studies on the preparation of the thin films of LaNi5 intermetallic compound, which is a typical hydrogen storage material, have been done hitherto. Adachi et al. , 2) and Sakaguchi et al. 3) prepared amorphous and crystalline LaNi5 thin films using flash evaporation of alloy powders and measured the pressure-composition isotherm for the prepared film utilizing a quartz crystal mass monitoring (QC:MM) method. It was found that the prepared amorphous film absorbed hydrogen without disintegrating into the powders and the hydrogen-absorption capacity of the films increased with the degree of crystallinity. Sakai et al. 4) reported that the maximum hydrogen storage capacities of amorphous and crystalline LaNi5 thin films, fabricated by a RF sputtering method using combination targets, were about 40 mA h g-1 (LaNisHo.7) and 160 mA h g-1 (LaNi5H2.6), respectively. Uchida et al. 5, 6) prepared LaNi5 thin films using flash evaporation of alloy powders and measured volumetrically the pressure-composition isotherm for the prepared film. It was reported that the hydrogen-absorption capacity of the films changed by the annealing treatment."

Jan 1, 1998

By Carla Lupi

NiMH sealed cells (portable cells) are today widely used in all consumer applications replacing primary alkaline batteries: wireless mobile communication, portable computers and camcorders, are the largest application segments. The Italian market. of NiMH cells is steadily growing, following the impressive penetration rate of the cellular phones. The organization of a national collecting system and correct recycling process are the key factors to prevent environmental impact associated to these wastes, while the metal values recovery can improve the feasibility of the recycling process The University of Rome, Texeco Engineering S.d, and MO.SMO.DE. S.a.s. have developed a combination of mechanical and hydrometallurgical processing to recover Nickel, and Cobalt salable products and rare earths intermediate products. A new plant located in South Italy, designed after this technology, is able to recycle waste Ni-MH batteries collected in the Italian territory, together with other industrial and portable batteries based on different chemistries. The process is able to treat both individual cells and plastic power packs and includes as basic steps an original crushing and elutriation treatment to separate plastic, metallics, and active mass components that are subsequently treated by a hydrometallurgical process to recover Ni, Co, and RE. The hydro metallurgical main steps are: acidic leaching, RE separation, multistage precipitation of Ni, Co and Fe and final solvent extraction on dissolved Ni and Co salts. For each operation the operative condition have been determined.

Jan 1, 2000

By Juan Daniel Martínez, Janaina Accordi Junkes, Dachamir Hotza, Tatiana Pineda

"The rice husk combustion in a bubbling and atmospheric fluidized bed reactor was investigated. The results showed the technical viability of producing both heat and amorphous silica from a renewable energy source. This paper presents the characterization of rice husk ash (RHA) obtained under varying fluidization velocities (0.13-0.15 m/s) and rice husk feed (4.5-7.2 kg/h). Characterization techniques include X-ray fluorescence, X-ray diffraction, particle size distribution and scanning electron microscopy. For the employed range of fluidization velocities of rice husk feed no noticeable influence on the chemical composition of produced RHA was observed. After combustion, RHA containing ~93% amorphous silica and <3% unburned char was obtained. RHA primary particles presented sizes from 90 to 100 µm and a tendency for agglomeration in aqueous media. Thus, the potential of this type of reactors with respect to speed, continuity and self-sufficiency energy of the process was shown.IntroductionDue to the increase of the agroindustrial production, the concern with processing by-products, such as rice husk (RH), is growing. For a better material and energy use, allowing a cleaner production and a more maintainable development, RH can be used as renewable fuel in the production plant, for instance, in steam generators. The adequate combustion of RH generates hot gases with low levels of pollutants, as carbon monoxide and particulate material.RH is the protecting coating formed during the growth of the rice grain, composed by four structural layers.1 The main components of the husk are cellulose and hemicelulose (50%) besides lignine (26%) and organic components (4%), as oils and proteins. The remaining amount includes inorganic materials (SiO2, Al2O3, K2O, Na2O, MgO, CaO, Fe2O3, MnO, P2O5).1The rice husk ash (RHA) is the product of the termochemical transformation of RH. The conditions of the different conversion processes (pyrolysis, gasification and/or combustion) determine the physical-chemical characteristics of the final product. RHA corresponds to 14 to 25% RH, depending on the variety of the rice, climate and soil of the producing area.2-4 The main component of RHA, which is generated at moderate combustion temperatures, is amorphous silica (SiO2) in the range from 80 to 97%.4,5"

Jan 1, 2008

By William Petruk

The development of automatic image analysers brought the application of image analysis into process mineralogy because the analysers can measure parameters more easily, quickly and accurately than by manual grain counting techniques, and can also collect data unobtainable by manual grain counting. Data from ore specimens and mill products are used to predict and to define the behaviour of minerals during processing. The analyses are generally performed on the basis of either surface areas or linear intercepts of grains in polished or thin sections, and the data are computer processed to give mineral quantities, liberations, size distributions, and characteristics of middling particles. For analysis, the minerals must be detectable and discriminatable from each other. An image editor is usually used when minerals are not easily discriminated. In addition BSE-8EM photographs have been used where the silicate minerals could not be discriminated from the mounting media. Methods of analysis, typical results, and their applications are discussed.

Jan 1, 1982

By Shadia J. Ikhmayies

"Tin oxide (SnU2) thin films of thicknesses in the range 100-600 nm were prepared on glass substrates by vacuum evaporation at ambient temperature. The films were characterized by transmittance measurements, X-ray diffraction (XRD), scanning electron microscope (SEM) observations and energy dispersion X-ray analysis (EDAX). It is found that the films have high transmittance and non sharp absorption edges. XRD diffractograms showed that the films are amorphous and the SEM micrographs showed that the surfaces are smooth, uniform and well covered with the material. The EDAX analysis showed that the films are deficient in oxygen. Indirect optical bandgap energy and Urbach tailing in the bandgap was observed, and the width of the tail, which is related with disorder and localized states, was estimated.IntroductionTin oxide is an n-type wide bandgap semiconducting material with a direct bandgap energy of 4 eV and an indirect bandgap of 2.6 eV [1], where inherent oxygen vacancies act as an n-type dopant [2], Tin oxide thin films have been used for transparent electrodes in photoelectric conversion devices namely amorphous silicon solar cells, liquid crystal displays, gas discharge displays, etc. [3]. Perfectly amorphous thin SnO2 films show good electrical response to reducing gases in air and could, hence, be applied to construct semiconductor gas sensors where the metal oxide films function as a monograin-eqivalent active layer [4]. Amorphous SnU2 can also be used in extended gate field-effect transistors (EGFET) as a pH sensor, where the sensitive part is made of the SnO2/Al structure. This device can be used to detect and to quantify any kind of substance that can produce or consume protons, like an enzymatic reaction, therefore showing a large range of applications as biosensors [5].There are different methods to prepare SnO2 films, such as atomic layer deposition (ALD) [6], reactive magnetron sputtering [7], chemical vapor deposition [8, 9], dip coating [10], spray pyrolysis (SP) [3, 11-14], and evaporation [8], The thermal evaporation method was chosen to produce SnO2 thin films in this work because deposition by this technique does not present any compositional problems. In addition, it is a low temperature technique, which increases the probability of producing amorphous films. To increase this probability, the films were deposited at ambient temperature."

Jan 1, 2012

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid aluimina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scanning electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By C. Acuna

The standard procedure of fire refining consists of sulphur removal via air injected through tuyeres, arsenic slagging via soda-lime flux and oxygen reduction by air or oxygen deficient air or a steam fuel mixtures. The use of porous plugs to stir with an inert gas has been mainly considered as a surface renewing agent that increases the product quality and shorten the refining cycle. In the present study the effect of the bottom stirring by nitrogen gas injection through porous plugs for the treatment of the crude copper in the range of 400-150 ppm sulphur, 3,000?2,000 ppm arsenic and 14,000-7,000 ppm oxygen content was investigated. The combined effect stirring-reducing, by the use of air or a steam fuel mixtures through tuyeres for oxygen removal, follows a kinetics of first order where the constant, K, can be represented by the following polynomial expression: K = A .* R2 + B * R + C Where A, Band C are constants that depend on the nitrogen flow rate and R is the air-fuel ratio or the steam-fuel used in the reducing step. Depending on the optimization of the flow of nitrogen and the air-fuel or steam-fuel mixture and only if just the oxidation, complexing and reducing steps are considered, the process cycle might be shortened by 45%.

Jan 1, 2003

By Jun Enriquez

Kennecott Utah Copper aims to extend anode furnace campaigns to more than three years. As part of that goal improvements are sought on anode-furnace tuyere-area refractory performance. Kennecott and Praxair developed high pressure nitrogen refining for the Oxidation Stage which shortened anode furnace fire refining cycles by up to two hours per cycle. Future developments include optimizing the Reduction Stage’s steam-gas reforming and achieving coherent jet tuyereless refining.

By Frederic Pineau

Semisolid metal alloys have a special microstructure of globular grains suspended in a liquid metal matrix. This particular physical state of the matter can be exploited to produce near-net- shape parts with improved mechanical properties. However, the behavior of the slurry is strongly influenced by the local solid fraction and state of agglomeration. Different flow instabilities ·associated with the combined flow and solidification process result, which make difficult the application of semi-solid processing in the casting industry. Moreover, the rheology of semisolid materials is not well understood. Most of the theory has been derived from experimental data, which are somewhat difficult to measure. A model that accounts for the multiphase nature of semisolid slurries is required to get more insight into such complex flows. This paper describes a mixture model for semisolid slurries. It assumes that the mixture of liquid-solid components behaves as a single fluid as far as overall mass and momentum balances are concerned. The coupling force between the phases is derived on the assumption that the slurry is a fluid saturated isotropic media. The proposed methodology is implemented in a finite element code. The model is then applied to the the filling of an industrial-scale capillary flow viscometer. Segregation patterns are obtained and discussed.

Jan 1, 2001