Search Documents

By Corale L. Brierley

Bioheap leaching, commercially applied for secondary copper ores and agglomerates, is rapidly gaining popularity. Bioleaching of chalcopyrite concentrates is imminent. Copper bioheap leaching encompasses the bioleaching of acidified and agglomerated coarse, secondary copper ore, stacked on permanent or on/off pads. The stacked ore is irrigated with raffinate containing bacteria. LME-grade cathode copper is produced by SX/EW. Low capital and operating costs, rapid start-up, environmental benefits, operational simplicity and a good performance record make bioheap leaching an attractive technology. This paper looks at the state-of-the-art of copper bioheap leaching and chalcopyrite concentrate leaching, the risks, the benefits, costs, bioheap performance and the future prospects of copper bioleaching.

Jan 1, 1999

By O. Kitamura, H. Kubota

The Harima Works started its ISP operation in 1966 and been expanding its production capacity from 3,000 tonne Zn/month and 1,500 tonne Pb/month to 7,500 tonne Zn/month and 2,500 tonne Pb/month. It is not only treating zinc, lead and bulk concentrates but also secondary materials like Waelz kiln oxide from the Shisaka Works of Sumitomo Metal Mining, waste treatment sludges, industrial wastes and others. Its final products cover Prime Western Grade (PWG) zinc, Special High Grade (SHG) zinc, continuous galvanizing grade zinc, electrolytic lead, cadmium, indium, thallium and sulfuric acid. This paper briefly describes the smelter's historical and present operations. The key data for the current impurity control management and for the distribution of impurities such as copper, iron and arsenic are presented.

Jan 1, 2000

By Jean-François Domgin

This paper aims at presenting numerical results showing the impact of different parameters on the limitation of entrained slag from ladle to tundish during the ladle drainage. These parameters are process parameters, slag properties or external actuator acting directly on ladle slag behaviour. Numerical simulations based on the use of the CFD Fluent software illustrate the vortexing and non-vortexing phenomena appearing during the ladle drainage. This numerical tool validated by experimental data acquired on water model has been applied to industrial configurations. It shows that the slag properties (viscosity, surface tension?) or some modifications of parameters (slide gate opening, geometry of the ladle bottom?) have a positive effect on the slag entrainment and also on the decrease of the ladle heel. Finally, the modelling of the behaviour of an external actuator injecting some gas in the region of the nozzle reveals interesting possibility for reducing slag entrainment from ladle to tundish during the final steps of the drainage.

Jan 1, 2006

By Xiaorong Liu

Interfacial emulsion generated in copper solvent extraction is an inhomogeneous O/W emulsion that consists of organic phase, aqueous phase and solid particles. In order to determine what kind of components in organic phase promotes the emulsion, the organic phase separated from the interfacial crud provided by Dexing Copper Mine in Jiangxi, China was analyzed for its components by combined gas chromatography-mass spectroscopy. It was found that many kinds of emphiphiles containing such hydrophilic groups as carbonyl, carboxyl, or acylamine existed in organic phase, most of which were originated from the reagent degradation. Conclusively, Lix984N would degrade gradually during a long-term contact with the acidic aqueous feed and strip reagents. Lix84 and nonylphenol, as effective components of Lix984N, degraded almost completely after long-term recycling. As a result, the effective components of Lix984N were far lower in concentration than the dense-aromatic impurities derived from the diluent and the degradation products in total. The degradation of Lix984N would deteriorate solvent extraction, disengagement performance and result in more serious interfacial emulsion.

Jan 1, 2006

By D. Nozadze

A new method of isothermal electro-contact diffusion welding of layered composites under pressure is offered. The scheme is developed and laboratory installation is created on which preproduction models of the layered composite of steel and aluminum is produced. A new method of electro-contact hot deformation is proposed for realization of diffusion welding by pressure of stratified blanks providing high-temperature isothermal process. In this case a rolling process or composite pressing is meshed with simultaneous electric current transmission in deformation center. Considering that a resistance of transient layer far exceeds the resistances of composite components, the heat release takes place intensively just in this layer. As the surfaces are approached over a distance of inter-atomic forces, the energy of boundary atoms easily reaches the energy threshold of capture with a formation of qualitatively new metallic bond. Proposed method, providing isothermal process in deformation center, excludes a necessity of previous preparation and prevention of surfaces. In this case strength of layer connection may approximate or exceed strength limit of cladding layer.

Jan 1, 2006

By Gerardo R. Alvear

The ability to efficiently remove impurities contained in concentrates is a key point to consider when selecting copper smelting technology for new plants or modernisation projects. Volatilisation of impurities such As and Sb should occur as early as possible in the process, and preferably in the smelting furnace, so that they do not impact on downstream unit operations. The ISASMELTTM process has been demonstrated to remove impurities efficiently, through high levels of volatilisation. This behaviour is promoted by attributes of the process such as the strong bath agitation, and the flexible nature of the process design, allowing the operator to choose the optimal matte grade for impurity partitioning, and the positive effect of the moisture content in the feed. This paper presents the distribution of minor elements in the copper ISASMELTTM furnace. Distribution impurities of As, Sb, Pb, Zn and Co observed in the ISASMELTTM furnace at Mount Isa Smelter are reported. Then, based on plant results and thermodynamic considerations, the potential application of ISASMELTTM technology for processing complex concentrates is discussed.

Jan 1, 2006

By E. M. Timoshenko

Autoclave technology can be effectively used for liberation of complex mineral raw materials to transfer valuable constituents into solution for their subsequent recovery or to refine feed material in order to remove deleterious impurities, e.g. arsenic. The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs, high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: - Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); - Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially at the stage of liberation (chemical upgrading) of raw materials are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent).

Jan 1, 2006

By Akram Salah Eddine Belaidi, Lakhdar Azzouz, Benchaa Benabed

"The dunes sand is a material of a large availability in Algeria. This material is practically unexploited. The introduction of this material as a new element in the construction can be more relieve the domain of building, and contribute to the development of the southern regions of Algeria, which are very rich in this material. The main objective of our work is to exploit a largely available material in the Algerian south which is the dunes sand, as a material of construction in the region of Laghouat.In this study, first we investigated the effect of the curing environment and the nature of the sand on the mechanical properties of the mortar, such as; flexural and compressive strengths. Then after, we studied the durability of the mortar under cycles of wettingdrying and the chemical attack of sodium sulfate (Na2SO4 5%).According to the results, we note that the mortar of the sand mixes (river sand plus dunes sand) present the best mechanical performances under different environment of curing. In addition result of durability studies put forward that the mortar of the sand mixes is more resistant to the sulfates attack."

Jan 1, 2008

By Tae-Hyun Kim, Shun Myung Shin, Jin-gu Kang, Jeong-Soo Sohn

We investigated about synthesis of Mn-Zn ferrite with spinel structure using sulfuric acid leaching solution of mixed spent zinc-carbon batteries and spent alkaline batteries. The waste batteries were prepared by physical treatment such as crushing, magnetic separation, and screening. After screening, the crushed batteries were separated to +8 mesh and -8 mesh powder. Among these, under 8 mesh powder was selected for leaching test. The leaching test was investigated at 2 M H2SO4, 4 vol.% H2O2, reaction temperature 60 ?, agitation speed 250 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of zinc, manganese and iron were 99.0%, 98.9%, 58.5%, respectively. For co-precipitation of zinc, manganese and iron, 5M NaOH solution was used for pH control. Then in order to synthesize Mn-Zn ferrite powder, it was investigated according to reaction temperature, agitation speed and O2 partial pressure. We could synthesize about 20 nm of Mn-Zn ferrite with spinel structure.

Jan 1, 2008

By John D. Kinton

A patent is a right granted by the government to exclude others from making, using, selling, offering to sell, or importing a claimed invention. Once the right is granted, the patentee may use the U.S. Federal Courts to enforce that right. Reading a patent from a litigation perspective is quite different than reading it from a technical perspective. The Judge's interpretation of the claims will affect their scope, and likely the ultimate outcome of a patent case. Additionally, the patent right can be challenged. If done successfully, the patent can be rendered invalid or unenforceable. The likelihood of success, and well as the achievement of other litigation goals is often influenced by the forum where the litigation is initiated. Finally, patent litigation costs are significant, and will weigh heavily in the decision to file (or fight) a patent lawsuit.

Jan 1, 2006

By Wei Liu

A new process for extracting cadmium from the electric precipitated dust produced by ISP process was studied. A leaching rate of 89.1% of cadmium was attained by leaching the dust with NH3?H2O-(NH4)2SO4 system under the best leaching conditions: ratio of liquid to solid(l:s)=2.5, c(NH3):c(NH4+)=3:5, total concentration of ammonium and ammonia=8 mol?L-1, leaching time= 1.5h, temperature=35. The most troublesome impurity of lead could be deposited from the leached out solution automatically after put it static more than 15h when the total concentration of zinc and cadmium was up to 45gL-1 , and the final concentration of lead was 0.0047 gL-1, which meant 99% of it was removed. Metallic cadmium which contained cadmium more than 99% was prepared by electrowinning under the conditions: current density=750Am-2, total concentration of Cd2+ and Zn2+>25gL-1. The current efficiency was about 87% and the energy consumption for every ton of cadmium was about 548KWht-1. Main impurities of the metallic cadmium were copper and zinc and all of they could be got rid of in the following pyrometallurgical refining step.

Jan 1, 2006

By Tae-Hyun Kim, Kang-In Rhee, Jeong-Soo Sohn

The synthesis of Mn-Zn ferrite powder from spent zinc-carbon batteries was investigated using a series of physical treatment, sulfuric acid leaching and coprecipitation. Physical separation methods such as crushing, magnetic separation and sieving were applied to generate a non-magnetic material of 8- mesh undersize for subsequent leaching process. The 8-mesh undersize of the spent zinc-carbon batteries was assayed 23.9% Mn, 14.9% Zn, and 4% Fe. Metal extractions obtained in sulfuric acid leaching at the solid/liquid ratio of 1:10, 2 M H2SO4, and 60? with 6 vol.% H2O2 addition were 97.9% Mn, 98.0% Zn and 55.2% Fe. The leach liquor was finally adjusted to the Mn:Zn:Fe mole ratio of 1:1:4 suitable for producing MnZnFe4O8 ferrite powder by the addition of Mn, Zn and Fe sulfates followed by pH control. A co-precipitation test for Mn-Zn ferrite powder was performed at 80?, O2 gas flowing at 1.3 L/min. As a result of co-precipitation, Mn-Zn ferrite nanoparticles in 20 nm size with spinel structure were successfully synthesized. The saturation magnetizations of Mn-Zn ferrite powder (Mn1-xZnxFe2O4) were determined to be 39-91 emu/g with various zinc contents (X=0.2-0.8).

Jan 1, 2008

By Bohumír Cech, Jirí Hanika, Václav Veselý

"PET bottles are separated and subsequently crushed into flakes. Except for PET, these flakes contain PE, PVC, paper, adhesives, beverages remainders and mineral impurities. PET itself usually is a glycol and terephthalic and isophthalic acid polymer.The suggested method consists in PET flakes crystallization at 255°C. In the meantime, volatile substances evaporate and PVC disintegrates. Formed crystalline PET is crushed into small particles and then is subject to the basic hydrolysis at an atmospheric pressure. In addition to lye solution, glycol is added in the hydrolysis. Water is eliminated by boiling, which gives rise to suspension of sodium salt of terephthalic acid and glycol. The suspension is skimmed and the filtered glycol is vacuum distilled. Pure glycol is then the distillation product.Crystals are dissolved in water and the solution is filtered, which eliminates PE and impurities. Electrodialysis removes pure terephthalic acid salt from the solution. Glycol solution is returned to the hydrolysis. Terephthalic acid is precipitated by a mineral acid. Subsequently, it is washed and dried. The filtrate is separated through electrodialysis to lye and acid. The lye gets back to the hydrolysis and the acid is used for precipitation. Terephthalic acid and glycol are products in a “polymer grade” quality. The waste is a part of washing waters, distillation residues after glycol regeneration and a filter cake after the terephthalate solution filtration."

Jan 1, 2008

By Ennio Bonetti

The technological applications of MgH2 hydrides for hydrogen storage demand the overcoming of some critical issues: an improvement of the reaction kinetics and a reduction of the desorption temperature. The synthesis of nanocrystalline MgH2 by reactive milling and inert gas condensation and a proper metal catalyst addition, constitute recently employed strategies. In the investigation of the hydrogen short and long-range dynamics, sorption kinetics and nanostructure stability, the mechanical spectroscopy offers some specific advantages. In the present research this technique was employed with other experimental approaches (XRD DSC) to investigate relaxational and structural damping processes in nanocrystalline MgH2 with added catalysts (Fe). Time/temperature variation of the dynamic elasticity moduli and mechanical quality factor are correlated to hydrogen anelastic relaxation processes and concomitant structural transformation of MgH2 to Mg associated to long range H diffusion. Results are discussed with reference to microstructural modification strategies able to assist hydrogen release.

Jan 1, 2006

The presence of clay adversely affects the floatability of copper and molybdenum during processing porphyry copper/molybdenum ores. In addition, reagent consumptions are much higher than when treating clay-free ores. Ores containing kaoline, brammollite, illite and montmorillonite were examined in the laboratory to determine how clay minerals affect the floatability of copper and molybdenum, and to find a possible solution to alleviate the harmful effect of clay slimes. It was demonstrated that the presence of clay mostly affects floatability of coarse and middling particles, and reduces selectivity. The results of the research work showed that there may be several possible ways of reducing the detrimental affects of clay slimes on flotation, some of which include a) use of alternative flowsheets, b) flotation at reduced pulp density, and c) the use of special frothers. The applicability of the findings in plant practice are discussed.

Jan 1, 1999

By Anthony C. Mulligan

Metals have historically been used in mining since they offer an excellent combination of hardness, toughness and cost and can be fabricated to form a variety of shapes. However, for many applications the metals used today have limited performance in the environments in which they are needed. This is particularly true for geothermal environments where the brines are highly siliceous causing corrosion and accelerated wear of many components. Geothermal sources are increasingly being explored for their high thermal value as well as possible sources for future minerals. While advanced ceramics have historically been expensive to produce in comparison with metals, they offer significantly greater corrosion resistance and hardness and can improve the overall performance when used in selected ?problem? areas. One of the major drawbacks in the use of ceramics in high impact areas has been their brittle nature and propensity to fracture and spall (fail) when loaded. Recent advances in the fabrication of ceramics have combined hard (strong) ceramics with more ductile ceramics in a architecturally designed microstructure, thus allowing ceramics to perform well in these high impact regions. Additionally, ceramics are significantly more inert to corrosion from either alkaline or acidic environments and can typically be used for significantly longer periods in these environments than their metallic counterparts.

Jan 1, 2006

By Jr. Santafé, Lucas L. da Costa, Felipe P. D. Lopes, Sergio N. Monteiro

"Residual vegetable fibers as leftovers from crops, industrial activities and consumable items are realistic options to be incorporated into low cost polymeric composites with the aim of replacing other commonly used materials. The present work assesses the technical properties of epoxy composites reinforced with residual fibers from the coconut fruit, also known as coir fibers. Based on these properties, an evaluation was carried out on these coir fiber/epoxy matrix composites to be used as building panels and furniture in comparison with conventional materials.IntroductionThe utilization of waste from industrial activities is presently recognized as important way in preventing environmental pollution as well as developing new products. This utilization would also generate employment and contribute to environmental improvement in global scale. Among such wastes, those from lignocellulosic materials represent a considerable potential for practical application. In fact, about 2.5 billion tons of these materials are currently available [1], and their fiber content is an important option for composites fabrication. Actually, lignocellulosic fibers are now replacing synthetic fibers as reinforcement in resin matrix composites owing to specific advantages such as low cost, biodegradability and renewable characteristics [2,3]. Moreover, as abundant waste, some of these lingocellulosic fibers could help reducing the use of traditional materials like wood and plastics in many industrials applications. This would prevent further stress on the environment caused by depletion of dwindling resources associated with forests and petroleum."

Jan 1, 2008

By A. L. Davies

The MTDATA computer software package consists of a rigorous implementation of an algorithm for calculating chemical phase equilibria by the technique of Gibbs free energy minimization and a database of the thermochemical properties of common materials, such as slags, mattes, metals, gases and aqueous solutions. We have used MTDATA to contribute to our understanding of the chemical reactions occurring in several specific unit operations of the Kennecott Utah Copper Garfield Smelter. The following two examples illustrate the range of environments to which the method is applicable. Calculation of the liquidus phase relations of the FSF fayalite and FCF calcium ferrite slags helped in the early diagnosis of several operating problems. Calculation of the deportment of fluorine between the FSF offgas and the FSG scrubber liquor helped in the identification of operating conditions under which significant hydrogen fluoride concentrations could be introduced to the contact section of the acid plant. Without the painstaking assessment of solution phase properties undertaken over many years, these calculations would not be possible.

Jan 1, 1999

By Beatriz Amarai Campos, Jorge Alberto Soares Tenorio1, Denise Crocce Romano Espinosa, Adriana Johanny Murcia Santanilla

"The aim of the present work is to investigate the recovery of nickel from obsolete cell phones printed circuit boards. The printed circuit boards were firstly submitted to a grinding process and then leached in sulfuric acid. Nickel was extracted from aqueous solution using Cyanex 272. Aqueous/organic ratio was 1/1. The effect of both pH and modifier addition on selectivity of extraction was investigated.IntroductionCurrently, electric and electronic equipments (EEE) have become a necessity to the modern life. Associated with this necessity comes the continuous and increasing replacement of those equipments by new ones. The accelerated technology advances are responsible for the generation of electric and electronic waste. This waste can be dangerous not only to human health but also to the environment. Waste of electric and electronic equipments (WEEE) has a variety of components and metals in its composition becoming a potential pollutant to the environment when not properly discarded. Its wrong disposal causes a loss of materials that could be recovered and reused. Therefore WEEE treatment is an important matter because it can assist the reduction of waste generated and the recovery of valuable metals.Printed circuit board (PCBs) is an essential component of EEE and is typically very complex from a chemical point of view. Several metals may be present in its composition, such as cooper, nickel, iron, zinc, lead, tin and silver1''. This characteristic hinders the development of a simple treatment, making it necessary the application of chemical and mechanical processing for their recycling'4'. The UN estimates that approximately 20 to 50 million of tonnes of WEEE are generated worldwide each year."

Jan 1, 2011

By Roger W. Lee

The commissioning of the prototype Imperial Smelting Furnace (ISF) in 1950 was a technological breakthrough in the pyrometallurgical smelting of zinc and provided significant advantages over the existing retort processes. However, for most zinc concentrates the electrolytic zinc process continued to be more economic. Therefore, the Imperial Smelting Process (ISP) specialised in smelting zinc and lead concentrates that were less amenable for treatment by either the electrolytic zinc process or the lead blast furnace. Subsequently, improved mineral processing techniques led to a decrease in the availability of these concentrates so the treatment of secondary materials in the ISP assumed greater importance. This was facilitated by the development of techniques such as hot briquetting and tuyere injection. In 2002 over 1 million tonnes of zinc and 400,000 tonnes of lead were produced by the ISP. However, in the 2002-3 the economics of the Process became extremely difficult because of low metal prices and increased operating costs. This resulted in the closure of four ISP smelters in 2003 and two in 2005. Nevertheless, two new ISP smelters are scheduled for commissioning in China in 2006 where local economic conditions continue to favour the process. The economics of the process are examined particularly in respect of smelter margin and operating costs. The need to increase the smelter margin means that the future of the process will be closely linked to its ability to consume secondary materials and an examination will be made of its potential for conversion to 100% secondary operation. Apart from a reduction in raw materials costs, a substantial reduction in operating costs would ensue from not operating sinter and sulphuric acid plants.

Jan 1, 2006