Search Documents

By I. M. Santos Moraes

Achieving high current efficiencies when operating at high current densities is a goal for every refinery, whether conventional or permanent cathode technology is employed. To obtain higher current efficiency at increased current density at Caraiba's Tankhouse, the production team decided to change the cathode cycle from eleven to thirteen days, reducing cathode cycle to one per anode cycle. The idea was to reduce the anode-cathode spacing and consequently reduce the potential for short-circuiting them. With respect to current efficiency, the overall result was not much better than that obtained with the normal operating conditions. A new attempt to obtain higher current efficiency at high current density was implemented by going back to two cathode cycles per anode cycle, this time reducing cathode life to ten days. This approach yielded the highest current efficiencies. This paper presents the data generated with the three operating conditions: normal practice, a single cathode cycle per anode cycle, and two cathode cycles per anode cycle with a reduced cathode cycle time. It compares the productivity achieved with each set of operating conditions. An analysis of the main operating parameters as well as the advantages and disadvantages involved with each condition is also presented for future reference.

Jan 1, 1999

By M. C. Ruiz

This work outlines the results of leaching studies on a copper concentrate containing chalcocite (Cu2S) and digenite (Cu9S5) with an acid saline solution of cupric chloride oxygenated at ambient pressure. The variables studied included the stirring speed, concentration of cupric ions, concentration of HCI, concentration of chloride ions, oxygen flow rate, temperature and time. The leaching system was found to be very effective for the dissolution of the concentrate. Over 95% of the copper was dissolved in 30 minutes with negligible dissolution of iron. The dissolution of copper increased with the stirring speed up to about 400 rpm and depended little on the total chloride concentration. The oxygen flow rate affected the dissolution of copper only below 0.1 1/min. The concentration of HC1 did not influence the dissolution providing its was sufficient to avoid the precipitation of copper oxychloride. The study of the effect of the temperature showed a maximum in copper dissolution around 90 "C

Jan 1, 1997

By M. M. Salari Rad

An investigation of gold distribution in the mill products of Sar Cheshmeh beneficiation plant demonstrates that on average 44% of the gold is routinely recovered as a by-product in the copper concentrate, and the remaining is lost to the tailing. In order to evaluate the causes of gold losses, the distribution and mode of gold occurrence in the Sar Cheshmeh ore and mill products were studied. Searching for gold within samples and within individual grains of sulphide minerals was carried out by SEM in the backscattered electron mode and SIMS, respectively. The mineralogical distribution of gold revealed by microbeam techniques were combined with the results of relevant metallurgical experiments including, sizing, heavy liquid separation, and diagnostic leaching tests, and the nature and location of gold in the ore and mill products were determined. The combined results of the experimental approaches pursued suggest that while there are some gold in solid solution and/or -colloidal size within sulphides of the Sar Cheshmeh ores, "visible" gold is the principal form of gold occurrence at Sar Cheshmeh.

Jan 1, 1999

By M. I. Hoschke

The viability of pyrometallurgically treating zinc containing materials is enhanced by recovering zinc metal rather than oxide from furnace gases. During the history of zinc production, there has been continuing development on methods of recovering zinc metal that has resulted in three commercial designs in use today. The most widely used commercial technology, currently producing 13% of the world's zinc, is the lead splash condenser which is attached to the Imperial Smelting Furnace (ISF). The other remaining commercial designs are the zinc splash condenser and the Wheaton-Najarian vacuum condenser. The need to treat increasing quantities of secondary zinc materials, particularly Electric Arc Furnace (EAF) dust, has renewed emphasis on the development of ways to recover zinc metal. Development work in this area has proved to be difficult. Partly as a response to these difficulties, studies into the fundamentals of zinc condensation and absorption have been undertaken. Pasminco Research Centre (PRC), Newcastle, is also developing a. new zinc absorber to recover zinc metal from furnace gases:. The design attempts to address the problems associated with current devices.

Jan 1, 1994

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior ofTiO2 nanopartic1es was thermogravimetrically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanopartic1es, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500°C at a heating rate of 1 C°/min. The weight increase curve showed a maximum of ca 30 wt% at around 750°?C and then gradually decreased to ca 12 wt% at 1000°C. This would be caused by the formation of TiS2 followed by the decomposition ofTiS2 to lower sulfides, such as Tit.0.8S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanoparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By Akira Yazawa

The composition of ferrous calcium silicate slag is located on the tie line between FeOx and calcium silicates in ternary FeOx-SiO2-CaO system. This slag has never been used as copper smelting slag because of high sulfidic copper solubility. However, when the dissolved copper in slag is just oxidic, as in direct white metal production or in converting process, this slag is quite attractive and can be regarded as the third copper smelting slag after fayalite and calcium ferrite slags. Based on the authors' studies on phase separation thermodynamics and laboratory experiments, it was clarified that the oxidic copper loss in this ferrous calcium silicate slag become the minimum not only %Cu in slag but also the total copper loss when the amount of slag is taken into account. It has been proven that calcium ferrite slag is suitable for continuous converting where the dissolved copper is oxidic, but there exist some drawbacks such as limited solubility of silica, low lead removability and too high fluidity. To overcome these difficulties accompanying traditional slags, ferrous calcium silicate slag is the hopeful alternative. In view of the general trends of modem copper smelting processes, the interesting features of this new slag system are discussed.

Jan 1, 1999

By Khosrow Nikkhah

Increasingly ion exchange systems are being included in design of hydrometallurgical plants for metal extraction or impurity removal. Because such systems operate sequentially and are based on resins that exchange one ion for another, store it temporarily and release it to a regenerating solution, the usual steady state heat and mass balancing tools and spreadsheets cannot be used to design them successfully. This paper outlines the role of dynamic simulation in design of ion exchange systems. Examples are given for use of dynamic simulation in design and investigation of equipment based on consideration of the effect of input criteria such as expected ion loading and elution profiles. The methodology for dynamic modeling using IDEAS in design of multi column ion exchange trains operating in parallel is presented. Results shown include the non-steady state distribution of extracted metal and limitations imposed on operating conditions. These conditions include proposed sequencing of columns for loading and elution cycles, loading, elution and recycle flow rates as well as size and choice of related ion exchange plant equipment.

Jan 1, 2003

By Tomas Astorga

APEC, the Asia Pacific Economic Cooperation is the forum of 21 countries having approximately 56% of the total world income, and over 45% of global trade. In 1997, APEC economies produced 67% of the world copper output, 55% of gold, and over 45% of other base metals. Mining in APEC captures more than 60% of the total mining investment in the world. New and emerging economies are now appearing in the demand scenery, such as China. New trends in the international environmental regulations are posing questions related to the use of copper in different industrial and consumption applications. These may have a strong impact on future trade of copper. New applications are also appearing based in new technology fields. The paper examines the growth potential of the copper market in main consumer ad highly populated economies of APEC, incorporating analysis of various interrelated factors. It also analyses the outlook of the copper supply. Its conclusions point to the need to implement demand outlook models. Finance and economic reforms will open important avenues for trade growth in basic metals, particularly copper. Changes in the consumption patterns of highly populated countries will add to better perspectives of copper demands. The recovery of a fast pace of economic growth in the APEC region will bring new demands for copper, especially as a consequence of high tech applications. More extended policies focused in the need for developing energy efficiency programs and schemes will add to this picture.

Jan 1, 1999

By E. García-Ramos, P. Flores-Sánchez, E. G. Palacios, B. Zeifert, A. Romero-Serrano, M. Hallen-López

Chromium containing slags from stainless steelmaking may eventually be leached by acidic environments, therefore they should be treated before being stockpiled or land filled. In this work, synthetic slags were prepared and the effect of CaO/SiO2, Cr2O3, MgO and Al2O3 contents on the stability of the mineralogical species formed was analyzed. The morphology and composition of the slags were analyzed by XRD and SEM-EDS, whilst their chemical stability was evaluated by leaching with an aqueous acetic acid solution. It was found that CaCr2O4 and CaCrO4 are present in slags prepared with neither MgO nor Al2O3. The Al2O3-based slags mainly produced Ca2Al2SiO7 and the Cr(VI)-containing oxide complex Ca4Al6CrO16, whilst MgO-based slags produced MgCr2O4 as main mineralogical species. Additionally, Eh-pH diagrams for the Ca-Cr-H2O and Mg-Cr-H2O systems at 25 °C were constructed. The lowest Cr concentration levels in the leaching liquors corresponded to MgO-based slags owing to the stable binding of Cr in spinel with MgO. It was also observed in the Al2O3-based slags that increasing the slag basicity from 1 to 2 the leachability of the slags are notably increased.

Jan 1, 2008

By Saskia Duyvesteyn

For many applications in hydrometallurgy and water treatment it would be advantageous to use ion-exchange resins in stirred reactors. However, attrition of the resin may lead to significant losses of both resin and metal values and prevent water quality goals from being reached. We have studied the recovery of fine resin particles by froth flotation, using the model copper - Dow XFS4195 chelating resin system. As the functional group on the resin is a bis-picolylamine, the resin should be amenable to flotation by anionic collectors, such as sodium dodecylsulfate and sodium dodecylsulfonate. The kinetics of copper loading from dilute aqueous solutions in an agitated vessel were studied as a function of copper concentration, pH and resin bead size. The flotation of unloaded resin was investigated for different types of collector, collector concentration, conditioning time, and resin bead size. Potential applications are discussed.

Jan 1, 1995

By C. Segawa

SMM operates an original slime treatment process for recovering precious metals and other metals (Te,Se,Sb,Bi)from the copper and the lead anode tankhouse slimes. In recent years, the amount of slimes has increased and the pyrometallurgical processing units capacity became the bottleneck of the entire plants. For the expansion of the plant, new pyrometallurgical facilities, incorporating a BBOC, was commissioned in 1992 and has now been successfully operated. In addition, unit operations were optimized to increase recovery and reduce operating cost .. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1996

By Hsin H. Huang

Equilibrium calculational software programs can be effectively utilized to model the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation on extraction and recovery processes. Illustrative examples using the calculational program ST ABCAL for the creation of diagrams such as EwpH, activity or concentration-pH, and activity or concentration-EH are presented to demonstrate the fundamental characteristics of real hydrometallurgical mercury dissolution and recovery processes. An industrial application will include leaching of mercury from K 106 mercury sulfide waste and solution purification by iron cementation.

Jan 1, 2003

By Roland Kammel

In combination with various physical and chemical methods also electrochemical techniques are most frequently used to improve the recovery of metals from aqueous dilute process streams or effluents e.g. in electroplating, metal finishing, mining and metallurgical plants. To insure cathodic metal recoveries with favorable current efficiency and high throughputs per unit of cell volume seve¬ral types of electrolysis cells have been developed comprising extended electrode surface areas and/or intensive electrolyte. agitation. The practical experiences with these units indicate especially for the electrolytic recovery of metals whose values are high, that the treatment cost permits profitable operations with relativly short payback periods for the units. Anodic reactions can be utilized for the removal of undesired anion contents or buildups of impurities. Appropriate combinations of these recovery methods are used to improve the versatility and the overall economy. Industrial applications reveal their potentional as addidtive techniques for existing processes to reduce the metal content of effluents to values that meet the guide lines of environmental legislation whereas integrated in-operation recovery methods are nowadays increasingly introduced to approach nearly close-loop operations.

Jan 1, 1992

By Shi Yuan

Molten copper was deoxidized using a one-end-closed yttria-stabilized zirconia (YSZ) tube. A thin layer of porous Ni-Zr02 cermet electrode was deposited on the inner wall of the YSZ tube. The outer surface of the tube was in contact with the melt and the inner surface with a flowing reducing gas. Without applying external EMF, the melt was deoxidized by short-circuiting the melt with the cermet electrode. The deoxidation process was analyzed and the rate controlling steps were identified. These experiments were also conducted at different temperatures to evaluate the effect of temperature on the deoxidation kinetics.

Jan 1, 1994

By M. D. Light

An intelligent control system (ICS) is being developed for ferrous iron oxidation by Thiobacillus ferroxitdans. The ICS provides computerized data acquisition and' control of process variables (temperature, Eh, pH, dissolved oxygen arid carbon dioxide concentrations and dilution rate) to maintain the ferrous iron oxidation at the highest possible rate. The ICS uses fuzzy logic for analysis of data inputs and implementation of control strategies. T:his paper provides preliminary information on the development of the ICS and? its operation.

Jan 1, 1991

By J. S. Lee

A new high performance adsorbent is synthesized by the sol-gel method and applied to the removal of cadmium and mercury ions from aqueous solutions. Adsorbents based on metal oxides have been developed by immobilizing chelating molecules on the surface of the existing metal oxide networks and show ability for selective metal extraction from aqueous solutions. However, efficiencies of such adsorbents are limited due to low ligand density, and difficulty in pore accessibility. These difficulties are circumvented by synthesizing adsorbents using the sol-gel technique. In one example to be discussed, the sol-precursor possesses an organic moiety that binds cadmium, mercury, and copper ions. The capacities of 1.98mmol Cd(II-/gm and 6.40 mmol Hg/gm of this adsorbent are considerably higher than those of adsorbents prepared by the ligand immobilization technique. The scope of this paper is to discuss the development of the new adsorbent and its applications for cadmium and mercury removal from aqueous solutions.

Jan 1, 1999

By M. C. Ruiz

The leaching behavior of chalcopyrite concentrate in acidic CuC12-NaCI-O2 solutions was investigated. Experiments were conducted under continuos flow of oxygen at atmospheric pressures. The results indicated that among the variables temperature has the largest influence on the dissolution of chalcopyrite in this medium, and high copper extraction can only be obtained at temperatures near the boiling point of the solution. It was also found that the stirring speed did not influence appreciably the dissolution of chalcopyrite. An increase in the oxygen flow rate up to 0.1 1/min increased the copper extraction. The total chloride concentration affects the dissolution of chalcopyrite up to about 4 M. Copper extraction of 93 % was obtained in leaching chalcopyrite of size fraction -400 # Tyler at 105 OC in 2 hours.

Jan 1, 1997

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

By O. E. Omotoso

This study is part of an ongoing investigation to understand the mechanism of stabilization/solidification of hazardous chromium wastes in ordinary Portland cement (OPC). Tricalcium silicate (C3S*),a major component of OPC is mixed with reagent grade Cr(lll) and Cr(VI) solutions, to simulate complex cementiCr waste systems. Scanning electron microscopy (SEM) and energy disperse spectrometry (EDS) were employed to provide microstructural and chemical information. Transmission electron microscopy (TEMlEDS), apart from complimenting the SEM, was used to probe the distribution of Cr in the hydration products of C3S and to provide crystallographic information. 29Si MAS NMR (magic angle spinning - nuclear magnetic resonance) Was used to characterize the influence of Cr on the hydrated silicate structure.

Jan 1, 1995

By T. Shibasaki

There is a strong demand in the photo industry to the higher quality of refined silver. Osaka Refinery produces about 27 mtpm of refined silver mainly from copper refinery slimes. Product quality is attained by controlling the impurity level in electrolyte. Copper is cemented with silver oxide and palladium is precipitated by a chelating agent. Both processes were operated previously in batchwise for treatment of bled out electrolyte, Recently these processes have been improved and made continuous to cope with the increased impurity.load. As a result the grade of fine silver has been maintained steadily at Pd < 3 ppm and Cu < 5 ppm.

Jan 1, 1989