Search Documents

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

By Brian E. Travis

The recent development of polymer grids for the underground coal mining industry has created new alternatives for supplemental ground control practices. The grids utilize strong, lightweight polymers - usually special grades of polypropylene. High tensile strengths and resulting load support characteristics are achieved by molecular orientation of these polymers in the manufacturing process. One of the most important applications of polymer grids as supplemental ground control is in longwall shield recovery. When shields are moved from one face to another, the determining factor in the success of the recovery is the ground control provided by roof support structures along the old face. Whereas primary support is usually provided by roof bolts and cables which run the full width of the panel, supplemental support is often provided by metallic meshes of welded wire or chain-link fence. lightweight, high-strength polymer grids replace these heavy, cumbersome metallic meshes, giving the operation increased productivity by decreasing installation time and reducing injury downtime.

Jan 1, 1990

By Russell C. Frith

Risk-based roadway roof support design is now a critical part of the Australian Coal Industry. Safe and efficient mining demands that roof support be tailored to the prevailing geotechnical conditions and coal mining legislation in New South Wales, Queensland, and Tasmania is clear in requiring that formalized roof support design be undertaken. The assumption of dead-load suspension of an otherwise unstable roof has been used in roadway roof support design for many years. However longevity does not necessarily translate into either a best or even reasonable practice in the current industry, particularly when pro-active strata management systems are now routinely used and reinforcing support design methods are available. The paper discusses why the assumption of dead-load suspension is fundamentally incorrect in almost all instances when pro-active or reinforcing roof support is applied and how it can easily result in misleading and potentially under-designed roof support systems under various circumstances. The commonly used design methodology of balancing the installed axial capacity of long tendons with the assumed ?weight? of a future roof fall is summarized, and several fundamental flaws are identified. The critical area of selecting the design Factor of Safety is also discussed in detail. Accepting that under certain circumstances the roof of a roadway will require it to be ?suspended?, suggestions are given for how a robust support system can be developed, designed and applied.

Jan 1, 2011

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987

By James Pile

Since C.C. White introduced coalmine roof trusses in 1967. many different systems have evolved. Beginning in the mid 1990's, several types of bar/cable truss systems have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, this new truss increases operator safely. In order to fully benefit from the new truss system, a closer look at the individual components and their interaction was undertaken to understand critical implications on preload and overall support capabilities.

Jan 1, 2004

By Li-min Liu

The Semi-Analytical method can be used to solve a variety of problems in geomechanics and civil engineering. When it comes to layered rock strata and rock masses, it is superior to all other analytical methods. This paper presents the application of a 3-D semi- analytical method to 3-D surface subsidence and stress analysis caused by mining. In this semi-analytical method the layered elements and triangular elements ate used alternatively. Their displacement pattern, strain mahix, elastic matrix, stiffiness matrix, load matrix and stress matrix are presented. A numerical simulation program based on the semi-analytical method bas been developed using Fortran 90. This program is suitable for subsidence prediction and stress analysis of mom and pillar mining, strip longwall and mechanized longwall mining methods. It is applicable to all geological conditions and mining methods. Comparing with the finite method, this method reduces significantly the number of simultaneous equations to be solved and the amount of data preparation. It not only reduces the computer memory, but also runs faster and cost less. Key Words Semi-analytical method, surface subsidence, stress analysis, layered element, triangular prism element

Jan 1, 2002

By Hideki Shimada

A low cost methodology that allows the determination of in- situ stress using oriented core specimens has been investigated. The technique can be used to determine the stresses during the early stages of a project, even in undeveloped areas of a mine. The research aim was to compare the experimental results estimated by the AE and DRA methods to those estimated by conventional ANZI (Australia and New Zealand Inflatable) cell measurements. The studies have been focused on fill stress tensor determination from a single oriented cored rock. In all cases the rock core specimens recollected the in-situ stress reasonably well compared with the standard overcoring method.

Jan 1, 2001

By Nicole E. Evanek, Anthony T. Iannacchione

"Over the past 36 years, a great deal of information has been presented and discussed at the International Conference on Ground Control in Mining (ICGCM). The topic of surface subsidence engineering has resonated throughout each of the 36 conferences, producing 155 related papers. These papers have come from many countries. The major focus has been underground coal, especially longwall mining, but hard rock mining has also received attention. This impressive collection of reports presents a unique opportunity to reflect on the progress made towards understanding subsidence basin characteristics and developing methods to predict and mitigate its impact.In the initial meetings, the focus was on measuring subsidence and developing prediction methods. As understanding increased, predictive methods were developed and tested, especially in North America, China, Australia, Europe, and India. Efforts were made to understand how structures, aquifers, and surface waters were impacted by the formation of subsidence basins. As time progressed, the number of papers dropped slightly and became more focused on site-specific conditions. Most recently, advanced monitoring techniques have revealed new information, spurring a resurgence in research activity. Another recent focus has been on anomalous horizontal deformations occurring in sites with significant relief. Several reports from Australia and one from the US have brought this issue to light. In closing, all of these surface subsidence engineering papers have chronicled the maturing of this most important topic and, in the process, highlighted the importance of the ICGCM in the evolution of our current state of practice.INTRODUCTIONThe aim of this paper is to examine the role of ICGCM in 1) shaping our understanding of the mining induced subsidence phenomena, 2) developing tools to help predict its impact on the surface, and 3) evaluating controls to mitigate these impacts.This analysis involved the consideration of 155 papers available within the ICGCM conference proceedings and listed under the subsidence topic. Three of the papers where only available as abstracts and were not included in this analysis. Four other reports were focused on topics other than underground coal mining-induced subsidence issues and were also not included. It should also be noted that papers dealing with overburden behavior were not included in this analysis. As a result, 148 papers were reviewed and analyzed (Figure 1)."

Jan 1, 2018

By Ezzeddin Bakhtavar

There are several geotechnical challenges and risks inherent in the interaction between the open-pit and block cave mining environments. This is especially true when they have to work simultaneously for a short time, as well as when only the caving operation is continued. Some of these challenges and risks include the induced zones of stress due to the large and deep open-pit, instability of the slope, instability of the crown pillar and water inflows, subsidence, and sometimes instability of the main accesses to the block cave portion of the mine. These challenges usually occur due to cave propagation. In this paper, these geotechnical challenges and associated risks have been studied and discussed. It was concluded that the majority of the mentioned geotechnical risks could be decreased, and often eliminated, by considering the appropriate dimensions of a stable crown pillar, especially in simultaneously working open-pit and block caving operations.

Jan 1, 2011

By Ross W. Seedsman

The feasibility of 6 m high single pass longwalling has been studied using Newlands Mine as a case study An intensive geological investigation identified a range of hazards but a mine layout was possible that minimised the risks with respect to joints, cleats, angular bedding, coal shears and horizontal stress. Geotechnical design input was required for support capacity, subsidence, gate to face transition, face span, and roof support. It is concluded that longwall face equipment can be made available by modifying existing designs, gate to face transitions will require a number of steps, and a mid-face sprag should not be required for routine operations.

Jan 1, 1992

By Chao-jiong Hou

The necessity of using tensible rockbolt in the roadway with soft rock, high in-situ stresses, mining influence and other complex conditions was discussed, the structures of three kinds of tonsibte rockbolt and design principle were introduced in this paper. The tests of analogue material simulation under plane strain condition and underground industrial tests indicated that the effect of controlling deformation surrounding roadway by use of tensible rockbolt was good.

Jan 1, 1989

By Cao Shenggen

Experiences in the developed countries have shown that continuous increase of panel width (or face length) is one of the major technical trends for high production high efficiency mines. Increasing the panel width will increase not only the panel output, simplify the gateroad layout, facilitate high concentration of production, but also increase resources recovery and facilitate protection of surface structures. This paper uses the No.4326 super- wide panel, Wangzhuang Coal Mine as an example. This mine employs the fully-mechanized top-coal caving longwall mining method. Through surface subsidence monitoring, the dynamic characteristics of surface movement were obtained. The dynamic surface movement during mining and the final surface movement after mining were predicted using the Mining Subsidence Prediction System. The results indicate that after mining, the surface above the super-wide panel reached a state of full subsidence, So it can ensure the No.309 National Highway above is located in the flat bottom of the subsidence basin, and there is little impact on the national highways when panels on both sides of 4326 Panel are mined.

Jan 1, 2003

By Joachim Leonhardt

Hundreds ofbolt-indicators were already used successfully in the German deep hard coal-mines to increase the safety and economy. The bolt-indicator offers the simple possibility to show roof-bolt (anchor-) loads. to indicate weak points as well as to optimize the anchor density and the dimension: The bolt-indicator is mushroom shaped and consists of coated metal. It is inserted between the anchor plate and the flanged nut. The loads appearing at the anchor are transferred to the bolt- indicator and can be recognized visually at the cylindrical part by the amount of the surface coating. Examples are used to clarify the application aims, operation and usage of the bolt-indicator and its yielding advantages in practice.

Jan 1, 2001

By Kevin Beauchamp

In many cases traditional support designs cover the many variations in ground conditions and bolt performance by a conservative factor of safety. The result is that most bolts are ineffectual most of the time and yet the response to occasional roof collapses is an even more conservative design. The probabilistic analysis presented in this paper takes several important parameters of a support design into account such as span, bolt strength, bolt length, water pressure, seismic accelerations, joint orientation, bed thickness and joint strength and allows the effect of variations in these parameters to be evaluated simultaneously. The analysis demonstrates the application of the probabilistic approach to both blocky, wedge-dominated conditions and bedded deposits dominated by laminations. All mine excavations have a designed stand-up time. By taking into account of the possible variations in the design parameters explicitly, it is possible to produce a support system designed to ensure stability over a given period of time. Rather than use a factor of safety criterion, the approach uses a percentage reliability or probability of failure. By understanding the probability of failure of the support system, it is possible to improve the performance of ground support without any increase in cost or conversely to decrease the cost while maintaining the performance of ground support. This approach reduces reliance on empirical experience and leads to a better understanding of the key factors that influence stability and can provide a much more accurate and optimized assessment of support design and performance. The result is a more cost-effective support system and we hope that a broader application of this approach to ground support in underground mines will lead to a greater acceptance in the industry of probabilistic analyses and of terms such as Probability of Failure and Reliability of Support.

Jan 1, 2003

By Wenbing Guo

Surface subsidence for fully mechanized thick seam top coal caving was measured, and surface subsidence characteristics were then analyzed. The subsidence initiation distance from the set-up room and the advance influence distance ahead of the advancing longwall face were studied. The maximum surface subsidence velocity and the delay angle of the maximum subsidence velocity were determined. The results indicated that surface movement was intensive, the surface subsidence velocity was very high, the ground surface was badly damaged, and the subsidence initiation distance from the set-up room was smaller than that in general geological and mining condition.

Jan 1, 2011

By Sun Henghu

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed. The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by excess water drainage under the ground are resolved.

Jan 1, 1992

By Ebrahim Ghasemi

Roof fall risk is a common problem in coal mines, and it is generally unpredictable due to variability in geological and mining parameters. In this study, a new fuzzy logic model was developed to predict roof fall rate in coal mines. Parameters such as coal mine roof rating (CMRR), primary roof support (PRSUP), intersection span, and depth of cover were considered as the model inputs. The model was developed based on experts? knowledge and also a database including about 109 datasets of roof performance from U.S. coal mines. Approximately 20% of these datasets were used to assess the performance of the fuzzy model. In each case, comparison between results from model and real roof fall rate showed that this model can predict roof fall rate to an acceptable extent.

Jan 1, 2011

By E. Hosca

Alternative tailgate loading conditions due to conventional and conventional/yield pillar combinations were evaluated to define roof loading. In order to isolate different loading situations, the tailgate entry was considered as part of the roof-pillar-floor system, which is controlled largely by the structural integrity of each member. A data bank of case studies was compiled, which contains details of roof and floor lithology, structure, support, and mining data, including any failure modes. The range of loading conditions that any tailgate can be subjected to was identified to form the basis of numerical modeling. Numerical modeling was then conducted on tailgate openings to determine roof, floor, and rib responses, including failure modes to a variety of loading conditions. Trends developed from the numerical modeling were modified using field data to form the basis for support evaluation and application. The effects of support were modeled numerically to determine optimum load capacity and points of application for reducing the potential for entry failure.

Jan 1, 1994

By T. N. Singh

With a view to producing increased target output every year, Indian coal mining industry is fast moving towards mechanisation but the present approach of mechanisation suffers from lack of standardisation, mainly due to nonavailability of the cutting data for various machine/rock combinations. The coal seams of the country are relatively hard in nature and the coaling machines are reported to be affecting production and productivity of the coal mine and the very trend of mechanisation. This paper presents the result of extensive study performed to visualise the cutting characteristics of coal seams of compressive strength ranging from 20 MPa to 65 MPa. In a specially designed drag bit type coal plough rig, continuous recording of cutting forces was done with the help of a microprocessor based data logger and the specific energy of cuttability was evaluated at different depth of cut and speed of cutting. The geomechanical properties such as compressive strength, orientation and frequency of cleats etc. and different indices of coal seams were measured in the laboratory and field and relationship was developed for easy determination of specific energy.

Jan 1, 1992

By Megan N. Witkowski

The purpose of this study is to investigate the susceptibility characteristics of domestic and agricultural water supplies that may be vulnerable to diminution or total loss of supply when active longwall mining is in the vicinity of the potable aquifer systems of southwestern Pennsylvania. The study focuses on water supplies in Greene and Washington Counties with reported losses or reductions in supply that were attributed to the seven active longwall mines in operation between 2003 and 2008. The undermined water supplies represent a variety of hydrogeological settings and mining conditions prevalent in the southwestern Pennsylvania longwall coalfield. The susceptibility characteristics investigated include hydrogeological setting, proximal location to mining, and climatic conditions at the time of impact. The investigation considers the relationship between geological and mining characteristics. Geological characteristics include overburden composition and geomorphology of the surface; mining characteristics include mining method, depth, and extraction thickness. It was determined from the study that the average overburden thickness at each mine site is indicative of hydrological changes to potable aquifer systems, with the overall impact frequency at each site decreasing as depth to mining increases. However, depth to mining was not the governing factor when hydrological responses were determined on a case-by-case basis. To fully analyze and hopefully predict potential impacts by longwall mine subsidence, it is necessary to consider additional factors including topography, distance to mining, mining method, and climatic conditions at time of undermining. The investigation serves the purpose of enhancing our understanding of hydrogeological responses to longwall mining and will aid in predicting potential impacts to southwestern Pennsylvania?s wells and springs in proximity to future mining.

Jan 1, 2011