Search Documents

Historically, the selection of mining sequence for multiple seam conditions has been based on many factors other than ground control considerations and minimization of interaction effects. Today, numerous operations are finding themselves mining above existing or abandoned operations, some of which exhibit large scale caving, pressure arches and subsidence troughs. Development of design criteria for the upper seam that would alleviate damage due to lower seam interaction effects can contribute substantially to the safety and productivity of many mining operations. The primary objective of this re search has been to identify methods of improving ground control conditions in the upper seam when mining through either passive or active subsidence waves. These methods concentrate on improved ground control practices for the upper seam, rather than reducing the amount of subsidence in the upper seams by improved practices in the lower seam. Design factors such as pillar size, pillar and opening orientation relative to the subsidence trough, offsetting intersections, and different support methods have been studied for the upper seam in a variety of typical geologic environments. Analysis has demonstrated criteria for ameliorating negative interaction effects and facillitating design in the superincumbent seam.

Jan 1, 1986

By David Allen

Cable bolting is a relatively new strata reinforcement technique that has been used successfully in Australia and the United Kingdom. Jim Walter Resources, Inc. has examined the principles and can visualize its useful application in many areas, such as: a) Longwall pull-out areas, b) Roadway junctions, particularly those involving yield pillars, c) Rib reinforcement, and d) Possible replacement of cribbing in roadways, especially longwall tailgates. This paper describes the conditions which led to cable bolt testing, the results of tests conducted to date, and conclusions about the direction that Jim Walter Resources, Inc. is heading as far as testing and potential applications are concerned.

Jan 1, 1994

By Mark K. Larson

Calibration of LaModel for deep coal mines begins with adjustment of overburden stiffness for load transfer distance. This calibration determines whether mining induced stresses are concentrated in the immediate abutment of the gob, or spread over a wider area. In the absence of site information, an empirically-based estimate is often used. Where data is available, a recommended calibration procedure can be followed, as is done in this case study at a deep western longwall mine, with minor modifications and extensions. In this case, data sources included borehole pressure cells, flatjacks installed in series with support Cans, and observed changes in ground conditions. Calibration was based on the first detection of mining-induced stress from the advancing longwall. Detection was found to depend on the type and sensitivity of measurement. Borehole pressure cell data with a 20-psi-increase detection threshold were chosen as the standard, in accord with data used in deriving empirical relationships. Application of this standard produced a load transfer distance estimate roughly four times the empirical relationship developed by Peng and Chiang (1984). This is a significant deviation with important implications for panel design at this site. Data from flatjacks, ground condition observations, and borehole pressure cells with higher threshold values, were tightly clustered and show load transfer distances from two to four times empirical guidance. Ratios between various measurements can be used to adjust measurements to the standard (although they may depend on mine geology). Once established, ratios can be used to adjust estimates, say from support flatjacks or ground observations, to the standard, where borehole pressure cell data is not available.`

Jan 1, 2012

By Danell. R. E.

A drill monitoring system has been developed which measures performance characteristics of a rotary drill and relates this to the material strength and rotary specific energy. The drill monitor is computer based and is used to produce a profile of the relative in-situ material strength as a function of depth. This information has been used in determining the placement of explosive in selective loading of blastholes and estimating the amount of lump product in a particular section of an ore body.

Jan 1, 1989

By J. R. Koehler

Although two-entry yield pillar-based gate roads supported by wooden cribs have been commonly used throughout longwalling in the Wasatch PlateadRoan Cliffs coalfield of central Utah, a three-entry yield-abutment gate road configuration was recently trialed in the Hiawatha Seam at the Genwal Resources (GRI) Crandall Canyon No. 1 Mine, near Huntington, UT. Pillar, entry, and cable bolt performance were monitored through second panel mining using a fairly extensive array of geomechanical instruments installed over a span of four crosscuts. Ground pressure and entry closure measurements confirmed that the 9.1-m-wide (30-ft) yield pillar was partially shielded from first panel longwall loads by the 36.6-m-wide (120-ft) abutment pillar, and consequently, experienced only minor yielding until the approach of the second panel face. Complete yielding of the 9. I-m-wide (30-ft) pillar occurred when the second panel was approximately 6.1 m (20 ft) inby the instrumentation site. Average cable bolt loads and differential roof sag remained low through second panel mining and tailgate entry ground conditions were excellent; however, very high ground pressures in the abutment and yield pillars, and second panel rib strongly suggest a high potential for coal bumps utilizing this gate road configuration at mining cover depths in excess of 396 to 457 m (1300 to 1500 ft). This conclusion is supported by the suspected occurrence of small coal bumps along the abutment pillar ribs, observed indirectly as fresh debris in the middle entry just behind the second face. This paper presents a case history developed from the geotechnical measurements and on-site observations of this unique application of a yield-abutment gate road configuration and cable support system in the Hiawatha Seam.

Jan 1, 1996

By Yuanwci Shi

This paper discusses the results of research on the interaction between roof strata and shield supports including the active and passive supporting functions of the shield supports which prevents roof strata separation; pressure distribution on the canopy and under the base plate as measured in the laboratory and underground; comparison between various shield structures regarding their effectiveness on roof and floor control; and determination of optimum support capacity under given geological and mining conditions including hard-tocave roof

Jan 1, 1997

By Vincent A. Scovazzo

On March 12, 1994, the 1,100-foot deep 2 Yard South panel of the 1l0 year-old Retsof Mine collapsed. At the time of this occurrence, the Retsof Mine was characterized as the world's largest, most productive salt mine. The collapse produced a seismic event and resulted in a sinkhole and small lake forming on the surface. An existing highway bridge was rendered unusable. Water entered the mine and despite valiant efforts by the miners and the mining company, the entire mine was flooded and lost. John T. Boyd Company (BOYD) studied the incident to evaluate design procedures, and assess the short- and long-term environmental impacts of the collapse. This paper presents our analysis of the cause of the collapse and our review of the rock mechanics design of 2 Yard South panel. Our review is, in part, based on a rock mechanics monitoring program of 2 Yard South. The monitoring program was established by the mining company as the panel was developed and continued even after the panel became unstable.

Jan 1, 1997

By Sanjay Kumar Singh

The mechanics of load transfer in bord-and-pillar mining is not well understood despite the evolution of the art of pillar extraction over the last 20 years via trial and error (empirical) or Rock Mass Rating (RMR), simple monitoring and pillar extraction experiences at neighboring mines. Variations in geologic conditions and pillar extraction methods, along with a lack of comprehensive instrumentation programs for monitoring ground behavior during pillar recovery, are among the factors that make it difficult to predict how strata will respond to pillar extraction. Efficient and safe use of roof supports depends on the interaction between the designed support and coal strata. Of particular interest in this study is the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods and optimum support with load-bearing capabilities in strata control during mass exploitation of underground coal deposits required detailed investigation,?. To provide a better understanding of the mechanics of strata deformation, as researchers, we have collected data and reviewed measurements of convergence and stress in one mine of South Eastern Coalfields Limited (S.E.C.L.), i. e., in North Chirimiri Pondary Hills (NCPH) and have completed numerical modeling with FLAC software for (Fast Lagrangian Analysis of Continua modeling, Itasca India Consulting Pvt. Ltd.) for two typical pillar extraction plans. Stress distribution in the mine roof above pairs of roof supports was calculated to demonstrate how Resin roof bolt support installed support contributed to roof block movement control. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal measure rocks and by pillar extraction sequences and layouts. Also, resin roof bolts and other support systems play a critical role in controlling stability of both the immediate roof and the main roof for a distance of up to 18 meters (i.e., working coal seam height X three times) above the seam. Installed supports provide unique strata control advantages over other types of secondary support by significantly reducing the time between mining and installation of the secondary support. Although resin roof bolts are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at nearpeak capacity(Singh, et al., 2006), whereas posts fail and lose their ability to limit mine roof deformation.

Jan 1, 2012

By Guoqi He

Common offset seismic data collected over two active longwall panels at different stages of mining reveal that significant arrival time delays are produced in reflections from different levels within the mine cover. Mining-induced arrival time delays are also observed beyond the edges of the mine over unmined areas. Reflection arrival time delays increase with reflector depth and are laterally variable. The arrival time delays are produced by reductions of seismic velocity within the overburden. Reflection arrival time delays from a major strong unit located neutrally within the cover are proportional to subsidence, however, delays in other events are not.

Jan 1, 1989

By P. Gaskell

The paper examines the development of rock movement between a longwall extraction horizon and the surface for a fully caved mining situation. Physical modelling has been used to examine the mechanics of ground movement and the propagation of fractures around the longwall working. The paper discusses dimensional analysis, model construction and measurement technique and data processing of the results into effective graphical forms for further study.

Jan 1, 1988

In this paper a numerical formulation is presented for determination of the axial load along a cable bolt for a prescribed distribution of rock mass displacement. Results using the program CABLE indicate that during excavation, the load distribution that develops along an untensioned fully grouted cable bolt depends on three main factors: (i) the properties of the cable itself, (ii) the shear force that develops due to bond at the cable-grout interface (i.e. bond stiffness), and (iii) the distribution of rock mass displacement along the cable bolt length. In general, the effect of low modulus rock and mining induced stress decreases in reducing bond strength as determined from short embedment length tests, is reflected in the development of axial loads significantly less than the ultimate tensile capacity even for long cable bolts. However, the load distribution is also dependent on the deformation distribution in the reinforced rock mass. Higher cable bolt loads will be developed for a rock mass that behaves as a discontinuum with deformation concentrated on a few fractures, than for one which behaves as a continuum, either due to a total lack of fractures or a very high fracture density. This result suggests that the stiffness of a fully grouted cable bolt is not simply a characteristic of the bolt and grout used, but also of the deformation behavior of the ground. In other words, the same combination of bolt and grout will be stiffer if the rock behaves as a discontinuum than if it behaves as a continuum. This paper also explains the laboratory test programme used to determine the constitutive behavior of the Garford bulb and Nutcase cables bolts. Details of the test setup as well as the obtained results are summarized and discussed.

Jan 1, 1996

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By John Smyth

Mining through in panel entries and the full face recovery method has been successfully practiced at U.S. Stwl, Mine 50. Suppat of the cut-through entries and recovery room is critical. Traditionally, concrete crib or fly ash cement backfill has been utilized. However, these traditional methods are not feasible at Mine 50 due to the difficulties of the plow face mining through these types of support. Recent development of new cable support systems provides an option for cut-through entry support. Mine 50 and Jennmar Corporation personnel have worked together to design and apply the cable systems in the cut-through entries and full face recovery room to eliminate standing support. To date, a number of full face recovery rooms and cut-through inpanel entries have been successfully mined. The results indicate that the cable systems combined with high capacity shields, have provided sufficient capacity to support the roof. Utilizing the Jennmar Finite Element Analysis (JFEA) computer program (Stankus and Guo, 1996), an analysis of the stress and roof deflection changes as the longwall gradually cut through was conducted. From the finite element analysis data, a supplemental support plan was designed. The history and experiences at Mine 50 are presented. Based on the case experiences and modifications made to the finite element analysis, an improved design criteria for future use has been formulated.

Jan 1, 1998

By V. M. Shick

With gentle bedding within the zone of support pressure the delamination in roof rocks may occur only on those stratification planes where cohesiveness of rock is close to zero. Unlike this, at dip angles of more than 30-35° disintegration of rock occurs on the surfaces with cohesion up to 5 MPa. Therefore, the delamination in roof rocks at inclined beds is greater than at gently dipping ones. The original disintegration along the pressure fissures with the formation of block structure at inclined strata is not typical, and it may be observed only in roofs with included thick rocks; in this case, the orientation of fractures depends on the angle of seam inclination. Deformation of roof roocks above the mined-out space is determined by anisotropy of layers stiffness (hardness). With the increase of dip angle the own bearing capacity of layers will rise in the direction of strike. It was emphasized that the natural and technological factors are of great importance for rock pressure manifestation in longwalls.

Jan 1, 1996

By D. J. Reddish

An understanding of the mechanisms that cause large seismic events in a deep mine provides a foundation for designing effective measures to reduce the incidence of these events, as well as reduce the potential for damage arising from these events. The work described in this paper focuses analytical efforts on major recognizable and controllable factors that influence mining-induced seismicity and serves to screen out many of the more random aspects of individual events. Information used in this study was developed in the course of a long-standing rock burst research program conducted by the U. S. Bureau of Mines in cooperation with mines in the Coeur d'Alene Mining District and regional universities. Information was collected on 39 seismic events having local magnitudes greater than 2.5 that occurred between 1989 and 1994. Five major types of events were developed from these data that describe all but two of the 39 large events. The characteristic mechanisms, tint-motion pattern, damage pattern, and relationships to mining and major geologic structures were defined for each type of event. This information provides a foundation for assessing whether or not changes in mining activity aimed at reducing one type of rock burst will increase the incidence of other types.

Jan 1, 1996

By Victor Nazimko

A new technique for reaming the holes has been tested. This technique is available for reaming a hole at its deep end creating an enlarged cavity that has helicoidal grooves oriented at less than 40 degrees to the hole axis. This technique increases bolt resistance by a factor 1.3-1.62; its bearing capacity by 3 times and enhances underground roadway stability. This technique is suitable for great depth (1000m and greater) and weak wet rocks.

Jan 1, 2008

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By W. C. Lacy

Stratabound copper ore bodies in thick Proterozoic metamorphosed sedimentary and volcanic rocks at the Tong Kuang Yu Mine in southern Shanxi Province of China were considered as possibly being amenable to block cave mining. Initial evaluation of caving characteristics was based upon old calyx drilling records, limited underground mining experience and geological mapping, a few diamond drill holes and measurements in surface subsidence features. Classification and mapping distribution of rock quality types aided in mine design, prediction of fragment sizing and explosive requirements, cave assist and ground support requirements. Comparison is made between early feasibility predictions and actual mine experience.

Jan 1, 1989

By Dave Bigby

Hatworth Colliery, operated by RJB Mining (UK) Ltd, is successfully mining the Deep Soft Seam at a depth of 1000m using single face retreat longwalling. The seam is characterised by a weak roof generally comprising 4 to 6m of well bedded carbonaceous mudstones overlain by weak siltstones. The paper describes the layout and support design strategies which have enabled the colliery to adopt sole support by rock reinforcement techniques for its longwall gateroads. To achieve this success the colliery layout has had to be radically modified to take account of the in-situ horizontal stress field. The layout is also closely controlled by environmental considerations, the seam being one of the gassiest in the UK Economic support by strata reinforcement has been achieved using a combination of rockbolting of the roof and sides installed at the face of the heading, and systematic double birdcage cable bolting installed on drivage and supplemented ahead of the retreating panel. The layout and support strategies have been developed through a combination of detailed underground measurement of support and stress parameters backed up by numerical modelling using FLAC. The FLAC modelling has paid particular attention to careful representation of bedding properties and validation through underground stress measurement.

Jan 1, 1996