Search Documents

By Murali M. Gadde

Welded wire mesh is the most commonly used skin control technique in the United States underground coal mines. Currently, selection of the mesh is based on trial and error rather than any rigorous design methodology. Several factors affect a wire mesh?s performance including the amount of rock material to be supported and how the load is distributed, wire gauge, aperture size, grade of steel, weld strength, bolting pattern and sheet size. Although the best way to choose the mesh is to conduct full-scale physical load tests, because of the limitations on the number of variables that can be considered in such tests and the requirement of an elaborate test set-up, it may not always be possible to use this option. An alternative would be to use numerical modeling to study the load-deformation behavior of a wire mesh. In addition to providing a very detailed stress, strain distribution in the entire mesh, the advantage of this approach is the ease with which parametric studies can be conducted. In this paper it is shown that the load-deformation curves generated by nonlinear numerical models match closely with laboratory derived ones. Then, based on parametric studies, design guidelines are developed to choose the mesh appropriate for different loading conditions. The modeling studies also bring forth the limitations of the current lab studies. For example, under some conditions it was noticed that the small sheet size considered in lab tests would produce higher mesh deformations than a full-size one used in actual practice.

Jan 1, 2006

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007

By Karsten Zimmermann

The paper presents a study on the influence of face retreat rate in longwall coal mining on surface subsidence. It shows possibilities to influence dynamic ground movement by using a specific and controlled winning regime. For this, a dynamic stochastic prediction model used by DMT in Germany will be proved and adjusted on the specific character of geology in the Northern Appalachian coal field. Occurring ground movements such as inclination, curvature and deformation can be analyzed under static and dynamic points of view. It is theoretically shown that the face retreat rate has only a small influence on the static deformation values, but directly affects rate and acceleration of subsidence and deformation processes. The study shows that because of low mining depth and high mined thickness, static deformation values have the largest impact to surface objects. This implies that high face retreat rates don?t affect the impact on surface objects.

Jan 1, 2007

By Hakan Gurgenli

Many coal seams have weak shale immediate roofs that cause ground control problems. Therefore, it is important to know the properties of these shales so that preventive measures can be developed in advance. However, it is sometimes hard to understand this rock type due to its unpredictable behavior. A good example of this situation is found in two shale coal mine roofs located in the Illinois coal basin (Herrin No. 6 seam). Although, these mines are located very close to each other, one of them has many roof falls, whereas the other has no measurable ground control problems. The aim of this paper is to explain why and how one shale roof behaves worse than the other. Laboratory tests, including point load strength index, slake durability index, moisture activity index, weatherability index, water content determination, swelling strain and x-ray diffraction tests were performed to analyze the shale properties. According to these analyses, some useful correlations were found between the engineering properties, moisture-sensitivity indices, and weathering properties. Finally, mine and support design considerations based on the test results were discussed and recommendations to prevent ground control problems were given.

Jan 1, 2006

By Paul Singh

Blasting is an integral part of mining activity and is an inherently destructive process. The quality of the rock mass in which an excavation is being driven has a strong influence on the level of dynamic forces to which the rock can be subjected and sustain damage. Though each specific rock mass occurrence is unique, yet there are common rock mass features which influence the outcome of controlled blasting in a similar way. A field study was conducted which involved assessment of blast damage at several operating mines and blasting of small scale models. The effects of block size and strength, joint parameters, ground water, weathering of rocks and rock mass rating on the results of controlled blasting have been investigated and discussed in this study. The influence of number and thickness of weak layers on overbreak control has been discussed in the light of practical data. Critical particle velocity ranges for damage to rock masses with different qualities have been outlined. An approach for the judicious design of perimeter hole pattern and charge concentration has been proposed.

Jan 1, 2007

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By David Hill

The Australian underground coal mining industry is increasingly operating in an environment that challenges traditional concepts of coal pillar design, against a background of heightened expectations and demands from other stakeholders with regard to the protection of both natural surface features and burgeoning civil infrastructure. The result is greater possibility of conflict between mine operators, developers and regulatory bodies, with potential for unnecessary sterilisation of Australia?s coal resources and/or escalating surface development / infrastructure protection costs. On the positive side some significant advances have occurred in the general level of understanding of pillar behaviour and stability, both in Australia and overseas. This paper examines some current issues in coal pillar design, focussing particularly on the application and limitations of analytical models of pillar loading. Established methodologies are reviewed and alternative approaches explored, including examples of key geometrical, geological and probabilistic concepts. Practical experiences from the Southern Coalfield of New South Wales (NSW) are examined for the purpose of highlighting critical variables. Finally, some suggestions are made with regard to the direction and opportunities for future research, with particular regard to coal pillar loading, in the interests of all stakeholders.

Jan 1, 2008

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

By Scott A. Shapkoff

High strength cable strand supports are predominately used as a supplemental means of ground control in longwall and development operations in the U.S. The advantages of cable strand supports have been documented and include flexibility, strength, and ease of installation. Since the majority of cable supports installed in the U.S. today are partially grouted, and this same segment of supports has no inherent installed tension, the supports are considered currently arbitrarily strictly supplemental and therefore, cannot currently be deemed primary support (in most mining districts). This paper details and discusses two distinctly different configurations and the technical advantages of active partially grouted cable supports for certain primary support applications. The evolution of the designs for both systems is highlighted. Field data illustrates the amount of active load in relationship to installed torque and the affects that component variables have on this load measurement. Roof control patterns using active cable supports are examined as alternatives for combination patterns using primary and supplemental systems. The importance of maintaining consistent installation procedures plays an important role in the level of performance of the system. Economics comparing the installation of active cables with other primary/supplemental patterns is also included.

Jan 1, 2006

By Keith Heasley

In many practical situation where the LaModel program in used to analyze the mechanical response and failure of the mining environment, there are very few actual field measurement from the site available for deriving the appropriate input parameters. For coping with this typical lack of field data, this paper presents some recommended calibration techniques derived from on an in-depth understanding of the laminated model formulation and from many years of experience applying LaModel to practical situations. For each of the critical input parameters (rock mass stiffness, gob stiffness and coal strength) in LaModel, a specific calibration technique is recommended and presented along with the justification for the technique and some appropriate derivations/equations for assistance. It is hoped that this frank discussion of recommended calibration techniques can help novice LaModel user develop better models and can initiate a discussion among rock mechanics experts on how to improve upon the presented techniques.

Jan 1, 2008

By Erik Westman

Coal bumps remain one of the industry?s most devastating but least understood phenomena. If changes to the internal conditions of the rock mass could be observed there is hope that bumps could be forecasted. Seismic tomography has been used over the past 25 years in an attempt to image these changing conditions in the vicinity of the longwall face. This paper describes the history and practical considerations of using seismic tomography in bump-prone coal mines. The implementation of seismic tomography at six different longwall mines will be described along with lessons learned. Early studies used mining independent sources of seismic energy, including explosives and sledgehammers. Subsequently more operator friendly sources, such as the mining equipment itself and mining-induced seismicity, were used. Seismic energy sensors have been placed in gateroads and on the surface above the mine. Each of these configurations has associated advantages and disadvantages. Although the results obtained have been encouraging, the application of seismic tomography to monitoring a bump-prone longwall face is still immature. The ultimate goal of clearly imaging changing stress conditions in the longwall panel in a manner that does not inhibit mining operation is still distant, yet drawing nearer. When this goal is achieved, the industry will have a capable tool for identifying locations where bumps are imminent.

Jan 1, 2008

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Carl Tom Blevins

Resin was first introduced to U. S. mines in 1971 and first produced in 1973. The original polyester roof bolt resin was very expensive and limited to a single cartridge size and a single slow gel time. Early resin applications were limited to very difficult ground conditions. Today approximately 80% of the over 100 million roof bolts installed in U.S. mines, tunnels, and construction projects employ polyester roof bolt resin. The industry has evolved from hand packing samples for trial testing to producing enough resin, if converted to a .9 inch (22.9mm) diameter cartridge, to encircle the world at the equator approximately three (3) times each year. Manufacturing and design improvements allow for a more consistent product with a wide range of applications at a price that is approximately 30% below our 1974 sales price. An inflation adjusted dollar buys six (6) times more resin in 2006 than in 1974. Modern gel times range from a few seconds to over 15 minutes. Viscosity is matched to bolt type and drilling machine characteristics. Multiple cartridge diameters and a wide range of cartridge lengths are offered by two operating companies. Resin manufacturers have also gone through a period of restructuring and change to meet the challenges of the mining industry. DuPont Fasloc has become Fasloc, Inc., a stand-alone company. Celtite became Fosroc then Minova, as it is known today. During this transformation, several manufacturers have either discontinued production or were absorbed. The industry led the development of the chemical grouting materials specifications contained in ASTM F432-95, Standard Specifications for Roof and Rock Bolts and Accessories. A history of the industry will be presented within a discussion of the evolution of the strength index, speed index, cartridge volume, class designation, and product marking requirements of ASTM F432-95.

Jan 1, 2006

By Frank E. Chase

During the past quarter century, coal mine geologists have evolved from providing a qualitative description of drill core and coal reserves into quantitative geotechnical specialists who bridge the gap between geology and engineering. In the late 1970?s and early 1980?s, hazard prediction mapping was in its infancy. At best, hazard maps identified rudimentary structures and conditions such as stream valley locations, sandstone/shale transition zones, and lineaments. A ?technical disconnect? had existed between geologists and mining engineers as each profession operated largely independent of each other. Engineers did not readily integrate geology and geologic conditions, with the exception of coal thickness, into mine planning. Geologists were relied upon for reserve estimates and did not participate in mine planning or design. The employment and market slump of the 1980?s and 1990?s combined with mining more challenging reserves mandated that this gap be bridged and forced geologists to learn to speak more ?numerically? to engineers so they could be understood. The purpose of this paper is to describe the procedures and thought processes used by coal mine geologists when determining various mineability and reserve extraction feasibility issues. The paper will also address underground geologic hazard mapping and prediction techniques. To achieve these objectives, the opinions and experiences of leading coal mine geologists, geotechnical and strata control specialists across the United States were solicited.

Jan 1, 2006

By Jin He

Based on the simple-beam theory, a stress analysis model was established for undermining in multiple seam strip-pillar mining when the strip pillars were not columnized; the effects of various mining factors (e.g., mining depth, inter-burden thickness, recovery ratio, etc.) on inter-burden stability were analyzed; the changes in inter-burden stress distribution were investigated; and the important role that the inter-burden spacing and the mining width of the lower seams on inter-burden stability was studied. Finally, the actual practice used in Feng Feng Mine area was used as an example to demonstrate the rational mining width for a fixed mining depth.

Jan 1, 2006

By Gennaro Marino

Documented case histories are studied where data were found on the initial collapse of the overburden above the longwall panels. Under this scenario, the most controlled conditions exist for assessing the span capacity of the overburden (i.e., before failure the roof spans to fin coal abutments on two to all four sides). In an attempt to correlate theory to field observations, data are used on the overburden lithology, and the depth, width, and face advance of the panel, as well as, the subsidence conditions noted on the surface. The subsidence measured on the surface is used to determine when complete failure in the over- burden rock has occurred.

Jan 1, 1987

By Daniel W. H. Su

Current longwall pillar design relies heavily upon past experience and many assumptions about pillar and entry response to longwall abutment pressures. Caving characteristics of the immediate and main roof strata are known to play an important role in the overall pressure redistribution, which determines the maximum abutment pressure, abutment pressure at the T-junction, and the width of influence zone. This paper presents the results of an extensive geomechanical study in a longwall panel at a West Virginia coal mine. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed by the instrumented locations. Overburden response to longwall mining was also monitored, and height of the highly fractured zone above the gob was determined by postmining drilling. Good agreement was observed between the measured stress changes and those computed using the known height of the highly fractured zone. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining.

Jan 1, 1987