Search Documents

By P. Bevilacqua, G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps consisting of water and solid particles. The solids usually consist of particles of different sizes, shapes and densities. Except in the special case of monocharacteristic particles, the particles are segregated by these differences in size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops a segregation theory that indicates the major variables involved. Experimental data on segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and nonmagnetic minerals are reported.

Jan 1, 1997

By Oliver Gutsche

High-pressure roll mill comminution of heterogeneous multicomponent feeds was simulated with artificial limestone-quartzite mixtures using a piston-die press. The influence of heterogeneous interactions between components of the mixture on grinding path, energy utilization and energy split have been examined. Primary fractures are governed by differential fracture strength and attrition resistance of the components at heterogeneous contacts; subsequent secondary and tertiary fracture events are governed by coarse-fine interactions in the particle-bed. The weaker component is preferentially ground out of the feed size fraction and concentrates in the fines. Energy split among the components in the mixture is a function of their relative fracture strengths. It doubles for limestone and decreases by a factor of 5 for quartzite over the entire range of the mixing ratio.

Jan 1, 1995

By Joe W. Siefke

The world-class Kramer sodium borate deposit is being developed by modern open pit operations near Boron, California. The deposit is a bedded, lenticular sedimentary sequence of borax and kernite crystals together with claystone. The borates dip south into a structural basin-bounding fault and were formed in the bottom muds of a permanent shallow lake. The lake was fed boron and sodium-rich solutions from a thermal spring source of volcanic origin. In addition to deposit geology, present day geotechnical concerns such as groundwater and slope stability will be discussed.

Jan 1, 1995

By L. M. English

A basic model was developed to help assess methane control needs for the longwall mining of coal in gassy areas. Rather than depending on reservoir and rock mechanical theories, it uses an empirically determined gas emission rate as an input, and it operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid in the determina¬tion of the number, size and location of vertical wells or other methane-control applications that are needed for gob gas control.

Jan 1, 2000

By J. A. Nelen, R. B. Cook

Panned stream-sediment, geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial sediments of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa Counties, AL, and Baldwin and Hancock Counties, GA. Identification and interpretation of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1990

By S. L. Huang, J. D. Rockaway, N. B. Aughenbaugh

Shale has long been recognized for its tendency to swell when exposed to the atmosphere. Interaction of moisture with exposed shale strata can cause serious ground stabi1ity problems, since the initial strength of a shale is reduced if the material is sensitive to moisture variations. In this paper, the authors present a classification system to estimate the response of swelling generated within shales. This characterization of the swelling potential is based upon plasticity, susceptibility to moisture, mineralogical constituents of clay size particles, and fabric. Use of this classification system in conjunction with other existing rock properties tests will provide data for more rational engineering design.

Jan 1, 1986

By V. Srajer

This paper deals with the problem of efficiently selecting the most appropriate loading and hauling equipment for surface mines. Problems and factors that affect productivity and operating cost are identified. During the course of collecting the information for this study, mining companies and equipment manufacturers were interviewed to define their selection practices. The majority of mining companies prepare general specifications and ask the suppliers to mate those specifications to their product line. The mining company then evaluates various proposals on the basis of the best available deal. The following 'mines from western Canada provided information for this study: Coal Mountain, Line Creek, Quintette, Westar's Harmer mine from the Province of British Columbia, and Coal Valley, Gregg River, Highvale, Luscar from the Province of Alberta.

Jan 1, 1989

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By Jed H. (Original by) Mosgrove

Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 ma/s (9000 cfm) of air at his last open crosscut.

Jan 1, 1981

By M. T. Ityokurnbul, M. P. Trubelja

Concentrate flow rates were measured for the flotation of -100-mesh Lower Kittaning coal in a computer-controlled 0.076 x 3.5-m pilot flotation column. The variables studied were recovery zone height, airflow and solid feed rates. The specific projected surface areas of the feed, concentrate and tailing streams were determined from the measured particle size distributions. The results obtained show that the concen¬trate flow rate was independent of recovery zone height but was dependent on the hydrostatic pressure setting (measure of froth depth), gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of bubble surface area flux and the specific particle projected surface area.

Jan 1, 1999

By B. Dabrowski, J. D. Miller, D. Halbe, J. Hupka

An air-sparged hydrocyclone (ASH) mobile system was evaluated for continuous stripping and recovery of cyanide (the AVR process) from process water at a gold plant site. The ASH unit performed exceptionally well as an absorber. HCN was removed from the gas phase in a single one second pass with an efficiency exceeding 99%. HCN concentration in the discharged gas phase was lower than 10 ppm, which provided for a safe working environment. The stripping efficiency, controlled by the Henry’s Law constant, exceeded 40% in one pass.

Jan 1, 2004

By Robert G. Moorhead

Fine-coal screening can be one of the most critical operations in a modern coal-cleaning plant. The yield and quality of clean coal produced in fine-coal circuits is controlled as much by how efficiently 0.15 mm (100 mesh) particles are sized as on the performance traits of the fine-coal cleaning device itself. In addition, the increased interest in effective fine-coal sizing operations indicates that many operators have also discovered its importance in affecting the quality and yield of clean coal produced in fine-coal circuits. This paper describes the three most prevalently used fine-coal screening technologies and discusses their sizing mechanism, performance, and application.

Jan 1, 1988

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By J. Drelich, J. Pletka

Lost foam casting is a process in which a polymeric material is formed into the shape of the part to be cast. Parts that are more complex are fabricated by simply gluing several patterns together. The pattern is then coated with a refractory material consisting of a mineral mixture and binders. Finally, hot metal is poured into the pattern, evaporating the expanded polystyrene and taking the shape of the coating shell. Prior to casting, a significant number of the patterns are damaged and inevitably landfilled. In this study, a process was developed for the recovery of expanded polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and pneumatic separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene. Key words: Casting, Lost foam process, Expanded polystyrene recovery

Jan 1, 2003

By David Sugden

Intense, tropical weathering of Cretaceous-Tertiary sediments has developed similar laterites in distant areas of the Amazon Basin. In two areas, Trombetas and Paragomina s, bauxites of commercial potential arc found. The bauxite comes mostly from the lower horizon of the three component laterite. The laterite is overlain by a clay cover, possibly an integral part of the weathered profile. The laterites are found on almost flat plateaus with individual areas of up to 80km2. There is a close relationship between the morphology and the ldterites. The process of lateritization is allegedly Pliocence but probably continues today.

Jan 1, 1984

By George J. Bujtor, Anthony K. Scott, Haddon F. King

In 1982, the result of a 3-year study was published as "A Guide to the Understanding of Ore Reserve Estimation". The principal conclusions were that computation formed only part, and perhaps not the most important part, of an estimate and that the estimate should recognize that geological, mining engineering and metallurgical judgements formed an essential part of the eventual result. Subsequent expectation/realization studies of several mines have produced case histories which form the principal basis of the paper. These imply that geology is even a larger factor than thought earlier.

Jan 1, 1992

By Johann Engelbrecht, Stéfan de Bruyn, Petrus van den Heever

A system for the on-stream X-ray diffractometric determination of mineral phases in slurries was developed in response to the mining industry's need for process control during the beneficiation of industrial minerals. The instrumentation for and results from testwork conducted at a phosphate rock beneficiation plant in Florida are discussed. Results show that the concentrations of the minerals apatite (var. francolite) and quartz can be accurately determined every few minutes, so that adjustments to the flotation circuit can be timeously executed from the control room. The on-stream measurements can ultimately be integrated into an automated plant control strategy. Estimates of savings on reagent and staffing costs, as well as the benefits from consistent grades and greater recoveries, have shown that the investment in such a system could often be recovered in less than a year.

Jan 1, 1999

INTRODUCTION Automatic controls are devices that assist operators by performing routine tasks faster and better than they could alone. Great strides have keen taken in the development of new processes and bigger machines to improve productivity, but these developments created the need for increased protection of machinery and labor. The new production-line techniques, or continuous processes developed, resulted in routine and, frequently, demoralizing jobs. The human race is not constituted mentally to perform routine operations. Devices were needed also to gather information automatically and perform routine functions. High-capacity plants incorporating large equipment

Jan 1, 1985

By Erich U. Petersen, Robert B. Coleman, William J. Tafuri, Donald M. Hausen, P. R. Taylor, Douglas N. Halbe, D. W. Rodolff

The definition of refractory gold ores and concentrates, including mineralogical characteristics, is reviewed. The chemistry of roasting and process conditions such as feed size, temperature, and time are discussed. A typical metallurgical program for developing a roasting process scheme is presented. The application of various types of furnaces for roasting is described. Requirements for scrubbing off-gases to meet environmental air emission regulations, and general information regarding engineering design parameters for roasting are presented. Roasting is sound technology for processing refractory ores and concentrates, but it is essential that the metallurgy of each ore or concentrate is well defined before commercialization. A fluid-bed roaster is the preferred type of furnace for roasting. Environmental regulations for air emissions must be carefully addressed.

Jan 1, 1990

By C. N. Bensley, S. K. Nicol

The major developments in fine coal processing in Australia are reviewed. Emphasis is placed on the approaches taken by various Australian coal producers to improve the recovery of the coarse size fractions (minus 0.5 plus 0.25mm) and upgrade the selectivity of flotation at ultrafine sizes (minus 0.075mm). The effects on fine coal preparation of flotation circuit changes, the influence of physical and chemical variables on coarse coal flotation and the impact of spiral concentrators and column flotation, are discussed. Reference is also made to the development of oil agglomeration technology for the treatment of fine coal refuse and some of the factors which have led to its current demise.

Jan 1, 1988