Search Documents

By N. S. Tanious

Three water-spray ventilation systems were tested to determine their effectiveness in diluting methane at a room and pillar coal mine face. These systems were: the shrouded nozzle, the spray fan, and the conventional nozzle system that is normally supplied with continuous miners. The testing was carried out in two stages. The air-moving capacities of the nozzles were first evaluated in a duct. The duct tests showed that: (1) the volume of air moved by the nozzle is controlled by the type of nozzle, the space around it, and its location relative to the duct wall; (2) the spray fan nozzles or the shrouded nozzles are both capable of moving air quantities up to 6400 cfm (3.02 m3/s); and (3) when the shroud was removed from around the shrouded nozzle, its bare nozzle moved between 9 and 65 percent more air. In the second stage of testing, a full-scale evaluation of the three systems was conducted. The three spray systems were mounted on a continuous miner which was positioned in an aboveground simulated mine entry. The simulated face tests gave the following results: (1) the standard nozzle system, which is mounted on the front end of the miner, is inadequate for diluting methane; (2) under the best testing conditions (lowest methane emission rate, highest primary ventilation airflow, and closest brattice set back), the slight improvement given by either the shrouded system or the spray fan is the same; and (3) under the worst testing conditions (highest methane emission rate, least primary ventilation airflow, and farthest brattice set back), the spray fan gave superior performance.

Jan 1, 1987

By David J. Kruse

Accurate field measurements are essential when validating a conveyor design. They are fundamental in determining a conveyor's behavior, its long-term maintenance requirements, and the life expectancy/ condition of the installed equipment. Field measurements are also invaluable in forensic engineering, particularly when vital equipment has failed This paper will discuss a wide variety of data acquisition equipment, field measurement techniques and accuracies achieved State-of-the-art, custom designed monitoring equipment, as well as, ''08-the-shely instruments and sensors, will be discussed.

Jan 1, 2004

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By K. A. Natarajan, Abha Kumari

In this paper, electroleaching and electrobioleaching of ocean manganese nodules are discussed along with the role of galvanic interactions in bioleaching. Polarization studies using a manganese nodule slurry electrode system indicated that the maximum dissolution of iron and manganese due to electrochemical reduction occurred at negative DC potentials of -600 and -1,400 mV(SCE). Electroleaching and electrobioleaching of ocean manganese nodules in the presence of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans at the above negative applied DC potentials resulted insignificant dissolution of copper, nickel and cobalt in IMH2S04 and in sulfuric acid solution at pH 0.5 and 2.0. Mechanisms involved in electrobioleaching of ocean manganese nodules are discussed. Galvanic leaching of ocean manganese nodules in the presence of externally added pyrite and pyrolusite for enhancement of dissolution was also studied. Various electrochemical and biochemical parameters were optimized, and the electroleaching and galvanic processes thus developed are shown to yield almost complete dissolution of all metal values. This electrobioleaching process developed in the laboratory may be cost effective, energy efficient and environmentally friendly. Keywords: Ocean manganese nodules, Electroleaching, Electrobioleaching, Galvanic interactions

Jan 1, 2003

By S. K. Mukherjee, A. W. Laurito, M. M. Singh, N. I. Jayaraman

This paper describes the application of foam to control respirable dust in a double-drum longwall mining section. The feasibility of injecting an adequate quantity of foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The details of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1987

By George P. Demopoulos, Vladimiros G. Papangelakis, Dimitrios Filippou, A. J. Monhemius, G. W. Warren, E. Peters

A new method developed for the estimation of the activity of Ht in mixed sulfate solutions is described and examples of application of this method to the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3 from 298 to 473 K are offered. The method makes use of an "extended Debye-Hiickel" type of equation that was originally put forth by Das for pure H2SO4 solutions at ambient temperature. The treatment of mixed sulfate solutions was made possible by combining that equation of Das with a speciation algorithm which calculates the abundance of all species formed. The developed method, which also takes into account ionic strength and temperature effects, was used to generate hydrogen ion activity and speciation data for all possible acid/metal sulfate pairs of the system H2SO4-ZnSO4-FeSO4-Fe2(SO4)3. Finally, under the light of the reported data, specific examples of hydrometallurgical reaction systems are analyzed in terms of thermodynamics or kinetics. In particular, the systems discussed are: hydrometallurgical precipitation of hematite, solvent extraction of Fe(III), acid leaching of zinc ferrite, and oxidation of Fe(II) to Fe(III) by O2(aq).

Jan 1, 1993

By Stanley J. LeFond

After two disappointing years where most industrial minerals posted decreasing production, 1981 saw an increase in production over 1980, or at least in status quo. Several commodities did, however, post significant gains. For example, bromine posted a 14% increase; fluorspar production dropped 21% in 1980, but gained 24% in 1981; and sulfur production increased. However, perlite was off 13% and manufactured sodium sulfate off 18% in 1981, while natural sodium sulfate production remained almost even with 1980. In fact, many industrial minerals production either remained constant, increased, or decreased only slightly over 1980. Increasing energy costs had their impact on industrial minerals in 1981. Hopefully, the recent downward trend in energy costs, at least gasoline, will financially help some of the more marginal plants. The 1979 shortage of rail cars that did not carry through 1980 also did not carry through in 1981. Rail rates increased 12.8% over-all last year, while average freight rates for industrial minerals increased 15.5%, according to Neil Johnson, consultant. Also, the trucking industry posted a 5-6% decrease in rates due to deregulation. All in all, we in the industrial minerals section seem to be holding our own at least. Stanley J. Lefond Contributing Editor

Jan 5, 1982

By Fernando Pendás, Jorge Loredo, Alumudena Ordóñez

Water derived from mine-tailings typically contains high concentrations of H+, SO4, Fe and other metals, and it frequently suffers a decline in pH and the development of acidic mine drainage (AMD). A paper describing the results of a series of laboratory experiments with real AMD and a subsequent field trial with a in situ pilot system to assess a potential method for remediating tailings-derived water is presented here. After testing different organic substrates, residence times and flow conditions during two years to determine the most appropriate treatment for a polluted Spanish AMD, a pilot scale system combining SAPS, ALD, oxidation/sedimentation ponds and an anaerobic wetland was designed. Preliminary analyses of effluent samples indicate acidity and metal removal is occurring within the system, although sulphate removal is not complete. The results of this small-scale field trial suggest a potential cheap, long-term alternative for remediation of acid mine drainage.

Jan 1, 2000

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

By Jiang Su, Alan Bloodworth

"Composite sprayed concrete lining (SCL), consisting of two layers of permanent sprayed concrete separated by a layer of spray-applied waterproofing membrane, represents the latest development in SCL tunneling, but presents several challenges to designers. This paper aims to address the following issues: (1) how to simulate composite action, (2) behavior of a composite SCL tunnel, and (3) how to utilize composite action to achieve lining thickness efficiency. It firstly sets out the background to the composite SCL concept, and then presents a strategy for numerical investigation. The main part of the paper is the presentation and discussion of the simulation results, focusing on the lining deformation, load sharing and the safety margin of both linings. Interface stresses are also examined. It is found that significant secondary lining thickness reduction may be achieved by utilizing composite action. Challenges for the design of composite SCL tunnels are briefly discussed at the end. INTRODUCTION Sprayed concrete lined (SCL) tunnelling has seen rapid development over the last twenty years in the UK (Su 2013). One of these developments has been the replacement of traditional sheet membrane and cast in situ secondary lining with innovative spray applied waterproofing membrane and sprayed secondary lining system, which has been adopted in recent major projects, such as Crossrail (Pickett 2013), and brings many benefits to the construction (Dimmock et al. 2013). The combination of sprayed primary lining, spray applied waterproofing membrane and sprayed secondary lining is perceived to provide a structurally efficient lining system that outperforms the traditional lining system, which consists of sacrificial primary lining, sheet waterproofing membrane and cast in situ secondary lining. The claimed benefits in structural performance arises from the composite action between the sprayed primary and secondary linings via the spray applied waterproofing membrane, which produces a much stiffer cross-section and therefore a more efficient use of materials. Early investigations on the design of composite SCL tunnels were carried out without (1) definite and reliable long-term interface parameters, (2) a verified numerical modelling technique, or (3) consideration of different stress histories between primary and secondary linings (Thomas and Pickett 2011, Marcher et al. 2011). This paper reports the findings from a numerical parametric study on a typical composite SCL tunnel with varied secondary lining thickness. The results show that the true benefit of composite lining arises from the optimisation of the lining thickness (stiffness) ratio between the primary and secondary linings to achieve secondary lining safety and thickness efficiency at the same time."

Jan 1, 2016

By W. Jacobi, F. Steinhausler, A. C. James

INTRODUCTION In 1979 the Committee on Radiological Protection and Public Health of the Nuclear Energy Agency (OECD) defined a programme of work needed to improve radon dosimetry and monitoring. A Group of Experts in this field was established by the NEA and at the first meeting of the Group the authors were designated an initial task with the following terms of reference:- To review dosimetry of radon, thoron and their daughters, and in particular:- - to examine analytical models for the assessment of dose to individuals who are exposed to aerosol mixtures of these nuclides; - to examine the state of knowledge of the characteristics of aerosol mixtures of these nuclides and other factors that influence the dose to the lung, and identify those parameters which should be measured for dosimetric purposes in radiological surveillance programmes; - to identify areas where further study or research are needed. In this presentation we attempt to examine, with these objectives, the relationship between exposure to radon and thoron daughter aerosols expressed in terms of the working level month l (WLM), or its SI equivalent, and dose accumulated by sensitive tissues of the lower respiratory tract. Over the past two decades many attempts have been made to calculate the lung dose equivalent to l WLM exposure in mine atmospheres, usually in terms of the maximum dose to basal cells in a small part of the bronchial tree. The calculations have employed variously detailed models of airway anatomy, aerosol deposition, ciliary clearance and dosimetry of tissue at the bronchial surface, and are well reviewed elsewhere (Walsh, 1970; UNSCEAR, 1977; Jacobi, 1977; Fry, 1977). They agree in the conclusion that basal cells in segmental bronchi (between about the third and fifth bronchial generations) receive the highest dose, although estimates of this dose differ by more than an order of magnitude, ranging from about 0.2 to 12 rads per WLM (2 mGy to 120 mGy). The most critical parameters of these models are the assumed depths of basal cells below the bronchial surface and the fraction of the WL carried by free ions. When more realistic values of these parameters are substituted (Jacobi, 1977), the dispersion in calculated maximum doses to basal cells is reduced to give a much smaller range from about 0.3 to 1 rad/WLM (3 to 10 mGy/WLM). The parameters and methods employed in these various models, however, remain too diverse to infer the sensitivity of the dose conversion to practical variations in aerosol characteristics and the additional factors determining lung deposition and clearance. We have therefore taken the approach of developing newer models (Jacobi and Eisfeld, 1980; James et al, 1980) that can encompass the range of available experimental data on the physical and biological behaviour of radon and thoron daughters and also accommodate the different interpretations that can be put upon them. We have paid particular attention to the averaging of dose over tissues of equal sensitivity in the lung

Jan 1, 1981

By T. Negeri

The simultaneous use of two or more families of collectors can sometimes improve one or more key flotation performance indicators, especially if the ore under consideration contains several minerals bearing the same metal. The maximum amount of collectors that can be used is limited by the need to maintain a high concentrate grade and selectivity. Therefore, when more than one collector is required, an experimental design that allows variations of both the proportions and the amounts with respect to other process factors has to be selected to find the optimum dosage. This type of design is known as "process factors in mixture amount experiment". It is a powerful design suitable for discovering the existence and evaluating the magnitude of the interactive effects between various flotation parameters. This paper elaborates the principles on which such a design is based, and demonstrates its usefulness with a case study.

Jan 1, 2003

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By Mark L. Munsell

In recent years, miners have tried many approaches to maintenance such as: - Highly sophisticated computerized programs. - large planning groups designed to preplan and schedule work. - Contract maintenance. - Break down maintenance. Each of these approaches has faced the added constraints: - High replacement cost of equipment necessitating longer useful equipment life - management?s increased scrutiny of all indirect costs such as maintenance. Faced with these factors, what system of maintenance control is right? After visiting many properties recently, it appears there is no right system. Maintenance programs need to be tailored to the people and production constraints that occur at an individual property.

Jan 1, 1976

By K. S. Venkataraman

The physical properties of clay-water systems depend on the complicated system of forces between the clay particles themselves, and between the clay particles and the ions in the liquid phase. The kind and distribution of ions in, on, and between the clay particles and the size and the shape of the particles are the basic factors determining the macroscopic behavior of clay-water systems. Understanding the system requires a knowledge of the nature of the clay particles, their size, structure, composition, and surface properties, and of the manner in which they interact with ions [and molecules] in the surrounding liquid [or other medium]. The validity of Professor Brindley's words (Brindley, 1958), written three decades ago in the context of making pottery, whitewares, and electrical porcelains, transcends time, and the basic message is perhaps all the more important in the considerably expanded use of ceramics for structural, thermal, tribological, electronic, and other applications. Silicon carbide, silicon nitride, and sialons have been studied in the last two decades for high- temperature structural and tribological applications, particularly for using in internal combustion engines. Titanates, zirconates and niobates of barium, strontium and lead, have high dielectric constants, and are extensively used in the formulations for making capacitors. Hexagonal ferrites (molecular formula MO.6Fe2O3) are in use for making permanent magnets for fabricating miniature motors, and for assembling loud speakers, particle accelerators etc. Cubic ferrites such as magnesium-zinc ferrite and nickel-zinc ferrite are used as transformer cores, and for other high-frequency applications. In this context, Richerson's recent book (Richerson, 1984) on the general scope of traditional and technical ceramics is a good starting point for an overview of contemporary ceramics technology. Glasses are a whole class of amorphous materials used widely as sintering aids, and for making glass-bonded ceramics and glass-ceramic composites. Composites are yet another burgeoning field where two or more particulate components are used for improving the performance of ceramics. For all these applications, the inorganic starting materials are almost always submicron and near-micron powders. Understanding the powders' physicochemical properties, and their surface chemical interactions with the surrounding liquid/gaseous medium is-necessary for making reliable ceramic parts at competitive prices. Even though ceramics science and engineering has attained its separate identity in universities and the industry, ceramists themselves would concede that ceramics science is a cross-disciplinary field, having incorporated and assimilated within itself many principles from several apparently disjointed disciplines. Principles of material science, graduate-level physics and chemistry, polymer science, surface and colloid chemistry, transport phenomena, particle technology, unit operations commonly used in chemical engineering and mineral processing, and statistics and applied mathematics are integral part of any ceramics curriculum in universities. Added to this is the fact that all bench-scale successes in making ceramic parts are to be scaled-up for larger throughput operations. Understanding and applying process engineering principles of comminution, classification, drying, calcination, etc. then becomes essential. CERAMIC FORMING: Despite the diversity of the materials and processes, conceptually, the steps involved in making ceramic parts have remained the same over several decades: The different components for making the pan (usually one or more powders plus other forming and sintering additives) are proportioned and mixed thoroughly, and the well-mixed formulations are consolidated into desirable shapes known as "green bodies." Usually binders such as wax, clay, organic polymers and surfactants, whether dispersed or dissolved in a suitable liquid are used during mixing the batch for giving strength for the green bodies. In the dried green state, the inorganic powders typically occupy only 55 to 60% of the bulk volume of the body, depending on the particle size distributions of the powders and the forming history, with mostly inter- particle voids accounting for the rest of the void volume. SINTERING: The formed bodies are then fired in high- temperatures kilns/furnaces during which the parts are exposed to a predetermined temperature profile, and "soaked" for a certain duration at the final high temperatures, typically between 1200 K and 1900 K, and then cooled to room temperature. The gaseous atmosphere in the furnace is controlled (oxidizing, reducing, or inert) when necessary. During the initial stages of firing, volatile liquids evaporate, and during the intermediate temperatures between 400 and 600 K, the the organic polymeric additives pyrolize and oxidize into water vapor, CO, C02, and other gases. At still high temperature, the glasses, when present, soften, and simultaneously, the ceramic particles rearrange into a network of grains with definite grain boundaries so as to reduce the total interfacial free

Jan 1, 1990

The floatability of a bituminous coal in NaG solutions was evaluated using a modified Hallimond tube to delineate the role of the electrostatic interaction between bubbles and particles in determining the coal hydrophobicity. Zeta potential measurements showed that bubbles are negatively charged in the entire pH range tested, while coal particles are positively charged below pH 6.0 and negatively charged above it. Also, both sodium and chloride ions were confirmed to act as indifferent ions without any specific effects for both coal particles and bubbles. Flotation as a function of pH exhibited a maximum and minimum at low salt concentrations which is shown to be determined mainly by the coal hydrophobicity as measured by a new hydrophobic levitation technique. At high salt concentrations (above 0.1 mole/dm3), the flotation without such maximum or minimum is controlled by the electrostatic interaction between the bubble and the particle.

Jan 1, 1992

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By Phillip J. Maddex

After the presentation of a co-authored paper, "The Cost of Transporting Ores and Raw Materials in World Markets", at the February SME meeting, one questioner commented, "You have been talking about the large shipper and ship loads. What does the small shipper do?" This paper will attempt to answer that question, at least in part. Probably the questioner hoped to hear about specific new tools and new techniques that he could apply. But one paper could only scratch the surface of the vast fund of information available; so rather than talk specifics we should take basics, that is, people, management and technology.

Jan 1, 1967

By C. Alan Tapp

Introduction Mine sampling determines the practicality of any mining operation. Improper sampling can result in an incorrect appraisal of present production and future potential. Therefore, the mine department in charge of ore-reserve calculations and mine sampling should be overseen by competent and experienced professionals with technical backgrounds qualifying them to produce accurate results. Sampling is a process by which portions of an ore body are collected and analyzed to estimate the average mineral content of the entire ore body. It is incorrect to assume that a large number of samples eliminates any errors in the sampling method. To obtain unbiased samples, proper sample location with respect to rock type and mineralization is just as important. The sampling procedure must yield correct results for the type of mineral deposit, and careful consideration should be given to whether or not the sampling technique has been developed to an extent sufficient to eliminate as much human error and bias as possible. Only after the ore has been mined and milled is the sampling accuracy known. Sampling also provides information about the bulk composition of the ore for mineralogical and metallurgical tests that determine the economic ore-waste boundaries and the geologic trends for exploration. Actual mining plans can be developed from this information to maximize profits. Accurate sampling is critical, and thus must be approached in a scientific manner. Sampling Techniques Sampling practices and techniques are as varied as the mines in which they are used. The method(s) chosen must be tailored to suit the company and mining needs. For instance, tabular uranium deposits, vein gold deposits, and porphyry copper deposits pose special problems in conducting unbiased sampling. The mine geologist or engineer in charge must develop a sampling method, test it in a sample area, and then critically evaluate the results. If the results from the test area are accurate within the economic limits established by the company, they then may be adopted for general use in the mine. Four routine sampling methods are suitable for specific sampling objectives in the daily mine routine: (1) channel sampling, (2) chip sampling, (3) grab sampling, and (4) bulk sampling. The final sampling results depend upon how the four methods are combined to accurately determine the grade of the ore body. When used in conjunction with each other during different stages of mine development, the channel, chip, grab, and bulk sampling methods provide an in-house check or a comparison by which mining methods and sampling procedures can be evaluated. However, the most valid check is based upon the daily mill production. Channel Sampling Channel samples consist of cuttings collected from a groove cut into the rock about 102 mm (4 in.) wide and 19 mm (0.75 in.) deep. Various tools ranging from a 1.8-kg (4-lb) hammer and moil to a pneumatic chisel can be used to cut the sample. Accessibility and rock hardness determine the applicable sampling tools. Before attempting to take a sample, the rock surface must be cleaned thoroughly; the method of cleaning depends upon the amount of mine dust accumulated on the surface or the degree of alteration of the rock surface. Typical cleaning methods 'employ a wire brush, water, or chipping a fresh surface. Next, the sample outline is marked on the prepared surface, taking care to choose appropriate sample loca- tions. After determining the proper sample outline and length, the sample can be chiseled out, catching the rock fragments on a canvas tarpaulin on the floor, in a powder box, in a canvas bag to avoid contamination, or by some other suitable means to capture all of the sample. Vertical veins present a special problem because the drift's back usually is arched, not square. For example, Fig. 1 shows that if sample intervals are measured from A' to D', the length of the sample interval is greater than the true vein width, resulting in an incorrect calculation of the ore reserves. The correct method would collect three samples at A'-B', B'-C', and C'-D', using either actual measurements in the mine represented by A-B, B-C, and C-D or trigonometric calculations to determine the true ore thickness. Then, each sample can be weighted by grade and true thickness for the vein. Channel lengths usually are a maximum of 1.5 m (5 ft), and it is good practice to divide longer samples into smaller intervals according to structures, changes in rock types, or differences in rock hardnesses. The influence of those features on the mineralization then can be determined. Chip Sampling Chip sampling is a variation of channel sampling used when the rock is too hard to channel sample economically or when little variation in the mineral content indicates that this sampling method will yield results similar to those of channel sampling. Rather than cutting a channel in the rock, small chips are flaked off at regular intervals over the entire face or area being the mine. sampled. Care must be taken to assure that the sample is representative of variations in the rock hardness and type. hi^ method is fast and useful in preliminary evaluations, but it should not be used for quantitative ore-reserve calculations. Grab Sampling Grab sampling is a fast method for double checking either channel or chip-sampling procedures, and, in some instances, mine production can be estimated from carefully taken grab samples. Grab sampling takes equal amounts of material at selected intervals over a mine dump, a muck pile, or from an ore car to estimate its Channel Sampling mineral content. Generally, this method is not considered reliable. Many independent variables can affect this type of sampling process. Thus, if the ore occurs in the softer fraction and a proportional amount of the result-

Jan 1, 1982

By G. E. Burrer, D. Malhotra, T. E. Irwin, S. Johnson

Climax byproduct-plant tailing assayed 0.019% WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The methodology used in the study and the results of this investigation are discussed.

Jan 1, 1987