Search Documents

By C. T. Thompson

"Rotary percussion" implies two types of energy, rotary and percussion. Into these categories fall rock' drills of varying sizes. The larger ones drill above 6" diameter holes; the medium size, 2 3/4" to 4 1/2" holes; and the smallest, 1 1/4" to 2" holes. Essentially, the larger holes are drilled with doom-the-hole drills using tri-cone bits. Percussion energy evolves from the drill piston and rotation power from the rotary table or overhead drive, using drill collars or pull down mechanism to preload the bit.

Jan 1, 1963

By V. I. Lakshmanan

Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market. Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogenous grinding. In addition to producing marketable coarse graphite by such autogenous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies.

Jan 1, 1984

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By W. H. Reck

he need in the mineral industry to treat increasingly larger tonnages has caused a demand for larger installations. In order to limit the size of these installations, it was necessary to build machines with larger capacities or production output. With this aim in mind, WEMCO Division developed the No. 120 WEMCO-Fagergren Flotation Cell in 1967. These large cells have been compared to conventional smaller cells from the standpoint of metallurgical performance, investment costs, power requirements and maintenance requirements in many plants throughout the world. Figure 1 illustrates the size difference of the No. 120 when compared with the No. 66. All results to date indicate the large No. 120 cell surpasses the smaller machines in all categories.

Jan 1, 1969

By E. H. Ahrens

This paper deals with the daily work of operating geologists and should be of interest to recent graduates. Working with development and production is quite different from exploration and many of the required skills and techniques must be learned on the job. Try to obtain your first position at a mine where good geological work is being done because it is important that you establish a solid foundation by learning valid techniques. Many do not! Those who desire to work in exploration are well advised to spend the initial two or three years at an operating mine where they will deal daily with an orebody during development and mining. Attempt to understand the controls of ore deposition and be interested in all phases of the operation. Learn something about factors which can adversely affect profitability and you will be a better explorationist.

Jan 1, 1983

By John S. Owens

The National Steel Pellet Project and the Butler Taconite Project are operated by The Hanna Mining Company in the vicinity of the towns of Keewatin and Nashwauk, on the western Mesabi Range. Production began in 1967, after seven years of exploratory and development diamond drilling and reconnaissance magnetic surveys, Previously, direct shipping hematitegoethite ores and gravity concentrates had been produced in the area from numerous open pits and several underground mines since the start of the century. Total shipments of these oxidized ores amounted to more than 200 million tons, but at the present time such reserves are nearly exhausted, and there are no mining operations in the Keewatin-Nashwauk area except at the two taconite projects. The locations of all of the present taconite operations on the Mesabi Range are shown in Figure 1, extending for a distance of about seventy miles from the Butler plant to the Dunka River area. The Butler and National plants have a combined rated capacity of 4.4 million tons of pellets. Their reserves cover a combined strike length of about eight miles on the Biwabik iron formation. All of the intervals between present taconite operations on the Mesabi are potential sources of additional magnetic taconite; in particular, exploration and economic studies have been carried out by Jones and Laughlin Steel Corporation in the Biwabik area between Aurora and Virginia, and by Pickands Mather and Company in the Hibbing area. However, west of the Henna and Butler holdings, it appears unlikely that magnetic taconite exists in commerical quantities at economic depths due to extensive oxidation of magnetite to hematite.

Jan 1, 1968

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product. The Hanna Mining Company's Groveland plant is no exception. The Groveland Mine is located in Dickinson County on the Upper Peninsula of Michigan. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper, and various iron silicates. (1) Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals. (2) A general flowsheet is shown in Figure 1. Flotation of the spiral tailings makes up about 75% of the concentrate. A minor amount of concentrate, less than 3%, is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tons per year.

Jan 1, 1968

By Bronson Stringham

The close area! relationship of Cretaceous or later intrusive porphyries to larger hydrothermal deposits of Pb, Zn, Au, fig, Cu, Mo, Hg,, and U of similar age in the Basin Range Province, was statistically shown in a recent paper (Stringham1) During the past year this study has been expanded to cover p11 of the larger hydrothermal deposits of similar nature occurring in the entire western United States. The sandstone type uranium deposits of the Colorado Plateau and Wyoming have been excluded since considerable controversy exists regarding their origin. The close relationship between intrusives in general and hydrothermal ore deposits has long been-recognized, but the association involving intrusive porphyry only, was suggested in 1954 when Sales concluded that the formation of porphyry may be an intermediate stage of activity between the development of granitoid rock and certain types of copper deposits. However: he applied this concept to only a few copper deposits. The relationship appears to be true also for a great majority of the hydrothermal deposits of the other metals mentioned above of Cretaceous and later age, at least in the western United States. This situation then leads to the conclusion then when exploring for similar types of hydrothermal deposits of the metals considered one may feel reasonably sure that if an intrusive porphyry of considerable size is. not present he may be facing much greater risk of finding an ore body than if a prophyry were presents Since, there are many intrusive porphyritic rocks which do not seem to be associated with hydrothermal deposit, it is believed that some distinct value can come from the recognition of intrusive porphyry which might be barren as well as the intrusive prophyry which might be productive This paper deals with that problem.

Jan 1, 1960

By Rod Heath

The Saskatchewan industry has the advantages of an ore body of a size and consistency unmatched anywhere else in the world, and large, efficient mines with production costs that compare favourably with those in other countries. On the minus side, Saskatchewan is remote from most major markets, and producers face a distribution challenge to reach the offshore markets which is the main focus of this presentation. One of the characteristics of the world potash business is that all of the major sources of production are located in the developed areas of the world, while there is no significant production in any of the highly populated developing countries. The major potash producers are located in Canada and the United States, in West Germany, France, Spain and the U.K., in Russia and East Germany, and in Israel and Jordan. There is currently no significant production in any of the countries in Asia (with the exception of Jordan where a plant is currently in the start-up phase), Africa, Latin America or Oceania, and all of these areas must, therefore, import a11 of their potash requirements from the producing countries.

Jan 1, 1985

By Henry W. Brandt

What is the most practical method for storing a huge quantity of crude oil for a long period of time to assure availability if conditions curtail the source of supply? Underground storage is a logical answer. But can abandoned mines be used for this purpose? That is the proposal Fenix & Scisson International, Inc. submitted to the S.F.F. Association (acting in behalf of the Department of Industries of the Republic of South Africa), Johannesburg, South Africa, in October 1966. This engineering and contracting firm with headquarters in Tulsa, Oklahoma, specializes in underground storage; and based upon previous experiences their engineers were reasonably certain that a mine could be used for storing crude oil. The answer subsequently proved to be "yes." The result was con- version of a coal mine to provide storage for a quantity of crude oil which is the equivalent of a sizeable oil field. The total cost of purchasing, testing, and converting the mine was less than 15 percent of the cost of conventional steel tanks. Operating and maintenance costs are proving to be about 2 percent of those experienced at two large tank farms owned and operated by the Association.

Jan 1, 1973

By Richard L. Wedertz

Although the physical appearance of excavating equipment doesn't seem to have radically changed over the past decade, important changes within the products and an innovative attitude on the part of the engineer in his design approach is becoming increasingly evident. The new philosophy is to go beyond simple refinements of existing designs that simply produce a machine which further reduces overall cost per ton or per cubic yard of material moved and to do it more efficiently than ever before. Standard ideas and preconceived notions have been discarded and have given way to providing a design and a machine that is best suited to get the job done. Understanding that the application will not always fit the machine, but, in most cases, the machine should fit or suit the application is a foremost consideration in the engineers' design criteria.

Jan 1, 1973

By W. F. Mullen

Within the scope of this discussion, artificial dimension stone is defined as any manufactured product used as a substitute for natural dimension stone. The history of the development of these substitute materials is reviewed briefly, representative characteristics of each product are listed, several analyses of their market position are presented, and suggestions are made for recapturing markets lost to these products and preventing additional inroads.

Jan 1, 1959

By Arthur A. Schweizer

A method to improve the quality of Magmnt zinc concentrates to become acceptable feed to an electrolytic zinc refinery. The magnesia content of zinc concentrates produced was too high due to particle locking with the sphalerite in coarse fractions. Regrinding of the concentrates to a very fine particle size and then refloating the sphalerite was chosen to eliminate a sufficient amount of the magnesia to make the concentrates acceptable.

Jan 1, 1981

By James L. Coburn

Leaching is defined as a form of extraction in which a valuable constituent is removed from a solid body by mass transfer to a solution which, for the purpose of this discussion, is considered to be an aqueous medium. Historically, leaching has been applied to the recovery and purification of many elements. This paper, however, is directed toward the recovery of copper, uranium, vanadium, and precious metals included in the following systems: 1. The leaching of copper minerals, sulfides and oxides, by acid or by ammoniacal leach solutions with or without an oxidant. 2. The leaching of gold and silver, either native metals or as minerals by an oxygen-containing alkaline cyanide solution. 3. The solubilization of certain uranium and vanadium minerals by oxygen or oxidant-bearing lixiviants. Many other systems of this general type exist, but from a production standpoint, these three systems account for most of the major values recovered by leaching.

Jan 1, 1975

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines' program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau's continuous residue processing plant, College Park Metallurgy Research center.' The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By J. L. Kohler

The knowledge-based expert systems (KBES) is a potentially powerful technique to the mining engineer in traditional areas of mine design and operations, as well as in the emerging areas of mining automation and robotics. Since KBES is still experimental in many respects, caution must be exercised as this "high tech" tool is developed and applied to mining. The objective of this paper is to demystify expert systems by introducing the elements of KBES, discussing the strengths and weaknesses, and identifying some areas of application in mining, based on the authors' experiences.

Jan 1, 1986

By W. C. Carter

In mid 1978 Inland Cement Industries Ltd. brought on-line their new one million megagram (Mg) per year cement plant at Tilbury Island, Delta, British Columbia. The Plant--Its Philosophy of Design The design of this plant began in 1974, at the beginning of the rapid rise in petroleum costs later referred to as the "energy crisis". The trend in fuel costs was clear, so one of the basic criteria for the selection of process equipment was high thermal efficiency. Throughout the process of selection of materials handling and process equipment, energy consumption was a factor in decisions. A second factor which influenced the design of the plant was its location on navigable water. The plant is designed to make maximum use of this means of transport to minimize transportation costs. All raw materials (and some fuel) are received by water, and a major portion of the cement and clinker is sent out by barge. Extensive modern dock and material handling facilities were provided to accomplish the shipping and receiving functions. A plant meeting stringent environmental regulations was the third major factor which formed the basis for design. To meet this requirement, all storage facilities had to be covered, 53 bag type dust collectors were applied throughout the plant, and materials handling equipment was designed to minimize dust and spillage.

Jan 1, 1979

By Louis I. Briggs

Evaporite rocks, salts of the more soluble ions in seawater, are deposited when seawater becomes concentrated by excess evaporation in marginal basins having restricted circulation with the open sea. The simple conceptual model of an evaporite basin (Figure 1) has a single inlet connecting the basin to the open ocean, the restriction to open circulation being caused by a bar or reef near the mouth of the inlet. As the oceanic water flows from the inlet into the basin it tends to form a thin layer of brine that spreads out over the surface of the basin brine, and as it does so, the salt concentration In the surface layer gradually increases owing to continued evaporation of the water. When the solubility products of the salts in the surface layer are exceeded, the salts precipitate and settle to the bottom of the basin, The order of precipitation follows their order of least solubility. Normally the carbonates separate first, followed by the sulfates and chlorides and the more complex double salts. In nature there is considerable overlap in their ranges of precipitation. The water flow in the basin, also shown schematically in Figure 1, diverges from the inlet essentially perpendicular to the lines of' equal salinity in the surface brine. The distribution of salts deposited in such a model will parallel the isosalinity lines, being arcuate and concave toward the inlet (1)

Jan 1, 1967

By A. Andreas

The transportation of mine products incurs a cost which can have a significant bearing on the competitive position of the product. This statement not only holds true for the transportation of the finished product but certainly as much for the in- plant haulage of the raw materials. Extensive literature is available both in North America and Europe on all aspects 02 these questions and to cite only a few of them: Pipelining of slurries, oil and gas, shipping of minerals and oil from the Arctic by icebreaking tankers, airlifting of metals or concentrates, etc. This paper is concerned with movable crushing plants as opposed to stationary and their influence on the in-plant transportation, that is trucks vs. belts.

Jan 1, 1973

By Alan J. Michaels

The paper addresses the problem of the high costs of accidents ad how AMAX Inc. - a diversified natural resources company - has managed to control its losses through a tri-thrusted approach of: (1) management commitment, (2) methods of implementation that are tailored to each division or local unit, and (3) a reward system for outstanding performance. Specific attention is focused on the Corporate Loss Prevention Department's "10 Point Program for Loss Prevention Management".

Jan 1, 1981