Search Documents

By Young C. Kim

In the past, underground coal mine planning has traditionally focused on the mine design n aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most of the underground coal mines within the U.S. With the enactment of the clean air act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the BTU contents of coal are of equal importance from boiler efficiency standpoint. Thus, the time has come when the coal mine planning must incorporate the coal quality control aspects as well as the traditional safety and efficiency aspects.

Jan 1, 1983

By David J. Akers

In past years, water drainage control in coal mines has been primarily directed on the basis of water quantity rather than quality. Due to the recent intense interest in total ecology and environment, emphasis has shifted to the point where the water exiting from a mining operation may be of better quality than when it enters. In most operations this has meant the use of treatment methods (neutralization) while the technology for the prevention of acid drainage is being developed or refined. To date, underground abatement of acid formation has generally been less expensive but also less effective than surface treatment of the mine water. It seems probable that total mine water pollution control will have to include both underground abatement and surface treatment methods. The general acid producing reaction involving the oxidation of pyrite - 2FeS2 (pyrite) + 702 + 2H20 ? 2Fe2S04 + 2H2SO4 - is well known, even though the individual steps are not clearly understood. The major implication of this reaction, that acid production can be eliminated by not allowing the contact of pyrite with free oxygen or water, has been well substantiated both in the laboratory (1,2) and in practice. (3) Underground abatement or control processes can be generally classified into two types: (1) the effective control or elimination of acid causing reactions within the mine, and/or (2) the reduction or prevention of water flow into and out of the mine. Recognizing the fact that these two types may be directly inter-related, this paper will, for the purposes of clarity and simplification, discuss each separately.

Jan 1, 1973

By A. K. Sinha

Inspite of the growing demands worldwide, thermal coal must compete in the market both in price and quality. The design and performance efficiency of coal preparation plants is thus crucial to the survival and profitability of a coal industry. While the coal recovery influences the cost of production, the quality produced by a preparation plant determines the selling price. Several coal preparation plant simulation models have been developed in recent years to help Improve the performance of coal preparation plants. A research project was recently conducted at Southern Illinois University to evaluate the practical applicability of such a model. The results of this study are presented and discussed.

Jan 1, 1986

By David L. Durler

In-situ uranium mining is a relatively new and innovative method utilized for the commercial extraction of uranium. As with any mining method, however, significant environmental concerns will be evident and must be addressed in a rational and far-sighted manner. Experience has shown that radiological and non-radiological environmental problems may not manifest themselves until after the in-situ methodology has become established and matured to some degree. It is important, therefore, to recognize potential environmental concerns and incorporate them into an environmental program that spans the premining, mining, and post-mining phases of an in-situ operation.

Jan 1, 1982

By Ted C. Mathews

Pre-concentration by sorting is as old as the mining industry. Inevitably waste rock is broken with ore. Separation may take place in the stopes by selective mucking and transport, or selective loading and transport of ore and waste by 12-cu, yd. shovels and 100-ton trucks in large open pit operations. Hand sorting of 1" to 16" pieces, formerly widely practiced at underground chutes and prior to or following first stage crushing, has greatly diminished in the United States with its high per hour labor cost, although still widely practiced in other countries and, surprisingly, in some of the most modern mills where inexpensive labor is available. The economics of pre-concentration by sorting is attractive since elimination of waste at any cost less than the total milling cost will show a profit. The size at which sorting should be under- taken is determined by the size at which liberation is secured to yield a product of ore and waste, and greatly influences cost and the point in the flowsheet where sorting can be undertaken. In some instances mining costs can be reduced where an inexpensive sorting system to eliminate waste is combined with a less selective and less costly mining method. This is particularly true in deep mines where hoisting capacity determines the rate of extraction and sorting is performed underground, with waste utilized for fill. Hand sorting, while efficient, is expensive because of low sorting rates. Peale (1) quotes man hour capacity at 1/3 ton per hour on sizes 3/4" to 3" copper ore, and up to 5 tons per hour on rich iron ore sized from 4" to 16".

Jan 1, 1974

By J. D. Miller

Pilot-scale tests indicate that effec¬tive concentration of fine gold from Colorado River sands can be achieved by flotation with the air-sparged hydrocyclone. The fine sands (55% minus 400 mesh and 0.01 opt*) from gravity concen¬tration were processed with a 5-cm air-sparged hydrocyclone (capacity -1.0 tph dry solids). Concentrate grades as high as 5.0 opt were produced in a single stage at a recovery of 75.0%. The separation efficiency was significantly better than that achieved in conventional batch flotation experiments.

Jan 1, 1985

By M. B. Mooiman

It has recently been discovered that the pH at which gold can be extracted from cyanide solution with primary, secondary, and tertiary amines can be increased 2 to 5 pH units by the addition of modifiers. Under these circumstances gold can be extracted at pH values from 9 to 11, commensurate with the pH range found in cyanide leach liquors. The selectivity of the amines and amine/modifier combinations for AU (CN)[-2] over other metal -cyanide complexes is presented and discussed. In addition, potential applications for the solvent extraction of gold from cyanide solutions are discussed.

Jan 1, 1983

By L. A. Pursell

The case history, which is the subject of this paper, involves the expansion of a lime plant in Texas. The major new production unit is to be a 545.45 tonne per day coal fired rotary kiln. Auxiliary facilities include additional quarry haulage equipment, modifications to the crushing plant, a hydrator, storage facilities, and a loading system. The existing plant consists of a high calcium limestone quarry, two coal fired rotary and 10 gas fired shaft kilns, nth crushing, screening, stockpiling, hydrating, storing and loading facilities. The proposed modification would increase quarry volume from 545,000 tonnes per year to 805,000 tonnes per year. The plan also includes the addition of dolomitic lime to the product line which requires the purchase and handling of 186,000 tonnes of screened, washed dolomite yearly. A decision to undertake such an expansion was previously a simple and straight forward process. Such a decision now faces a major and complicating obstacle which can delay the project, raise the expected cost, or prevent it entirely.

Jan 1, 1980

By Vladimir Jindrich

This paper presents a history of a successful three year effort in locating a large, economic deposit of high purity limestone. The exploration program has been carried out by Ernest K. Lehmann & Associates, Inc., geological consultants, for Dravo Corporation, owner of the limestone property which is now under development. The permission of Mr. L. P. Struble, Jr, President of Dravo Lime Company, and Mr. M. W. Robinson, Director of Research and Development, to present this paper is gratefully acknowledged. The limestone property is on the Ohio River near Maysville in northern Kentucky, 60 miles east of Cincinnati (Fig. 1). The area lies at the eastern flank of the Cincinnati Arch, a regional structure where the Lower Paleozoic strata crop out below the adjacent younger sedimentary rocks of the Illinois and Apallachian basins. In general, the limestone formations of the Middle Ordovician High Bridge group offer the best potential for industrial limestone in Kentucky and adjacent parts of Ohio and Indiana. These formations are exposed along the axis of the Cincinnati Arch in central Kentucky. Toward the west, east and north, strata of the High Bridge group are progressively deeper, concealed beneath a succession of interbedded fossiliferous limestone and shale. The High Bridge group limestone formations are shallow-marine deposits largely of tidal flat, shallow lagoon and related environments. Principal lithologies include cryptocrystalline micritic limestone and crystalline dolomitic limestone to dolomite. Shale and bioclastic limestone are subordinate but the proportion of shale increases in the basal formations. Characteristic, is the occurrence of several thin beds of bentonite that serve as regional stratigraphic key horizons.

Jan 1, 1975

By Aarne Visnapuu

Unmodified pneumatic rock drills may have noise levels of 115 to 130 dB at the operator's position. Experimental modifications have been made to a standard drill to suppress the noise from the three main sources: the air exhaust noise, the noise radiated from the drill, and the resonance noise of the steel drill rods. A prototype model developed at the Bureau of Mines, Rolla Metallurgy Research Center, operates at a noise level below 100 dB. A close-fitting case and muffler unit, consisting of a metallic skeleton filled with viscoelastic absorber and having a durable cover, provided both muffling and noise absorption. Damping alloys were used at strategic points in the drill. Drill steel resonance noise was reduced by a constrained-layer treatment on the outside of the drill rod. The singular and combined effects of the treatments are presented in detail.

Jan 1, 1973

By C. K. Jankousky

The midwestern area referred to is the Illinois basin. The coals presently worked are mainly the No. 5 and No. 6 coal seams which vary in thickness from five to eleven feet. Present average of the more important No. 6 id about nine feet. The coal can vary considerably in toughness within the same mine with some coal perhaps rashing very easily and other coal being extremely difficult to cut. Top is generally well laminated shales with some fortunate areas having limestone roof. There are local areas with troublesome top of poorly laminated shales, shale with slickensides and shale intermingled with small partings and traces of coal. The bottoms are generally one to three feet of clay which softens readily on exposure to moisture. The mines are dry although some water is released and collects from rapid penetration of the seam by continuous miners. However, there are locally wet areas. Most of this material refers to mines of the Freeman Coal Mining Corporation. The mining operations written about are underground mines in southern and central Illinois.

Jan 1, 1962

By Francis G. Stehli

Though sedimentary rocks comprise only about five percent of the volume of the continental crust, they cover about 80% of its surface, serve as important reservoirs for fluids, contain reserves of non-metallic minerals, and have in general been extensively drilled. However, most drilling has been shallow in comparison to the thickness of the crust and such deep drilling as has taken place is very strongly localized in sedimentary basins. This may be seen by reference to Figures 1 and 2 which show the location of wells that drilled deeper than 15,000' [=] 4.6 km. (Figure 1) and those that drilled below 20,000' [=] 6.15 km. (Figure 2). It is apparent that, even in regions of sedimentary cover, direct exploration below six kilometers has been very restricted. In the case of the metamorphic and igneous rocks which make up 95% of the volume of the crust, direct exploration has been much less extensive in terms of both area and depth. The present state of our knowledge of the crust below a' thin surface layer stands in marked contrast to our growing present need for raw materials and the needs of future generations. It also stands in contrast to our need for enhanced, scientific knowledge of the deeper crust, its configuration, its present state, its hydrothermal systems,-its evolution, and its materials. Lessons learned in exploring the third dimension of the sea floor, the vigorous prosecution of seismic profiling, the development of testable models for hydrothermal systems and mineral deposits, the need for better understanding of heat flow, state of stress, earthquake mechanisms, and a host of other phenomena all suggest that it is time to launch a national program for scientific exploration of the crust which uses drilling to test important hypotheses developed on the basis of indirect evidence.

Jan 1, 1985

By Walter N. Campbell

The Simon Silver Mine is located near Mina, Nevada, approximately 50 miles northwest of Tonopah and 40 miles east of Hawthorne. It is an old property which was last worked in 1932 and closed operations due to problems arising from low metal prices. Federal Resources Corp. acquired the property in 1963 and undertook a completely new development program since the old surface plant and underground workings were beyond feasible repair. The deposit of silver, lead, zinc and copper is predominantly replacement of limestone. In the summer of 1964, a new surface plant was constructed and on December 2, 1964, sinking of a three compartment vertical shaft started and was completed to a depth of 1088 feet in April of 1965. Following the sinking program an 850 foot crosscut was driven to intersect the mineral zone on the 1000 level after which drifting, crosscutting and raising totaling some additional 4280 feet has been completed along with considerable diamond drilling and long holing into the walls. To date, two ore bodies have been encountered and test stoping operations are underway together with development of the 800 level for servicing, ventilation and access. The present development of ore is directed towards substantiating sufficient reserves to warrant the construction of a flotation mill.

Jan 1, 1967

By A. S. Speirs

Over the last few years, the never-ending search for mineral wealth has taken the exploration efforts of Canadian mining companies further and further into the High Arctic and isolated locations where regularly scheduled transportation and communication facilities are nonexistent. Names such as Black Angel, Nanisivik, Asbestos Hill, New Quebec Raglan, Rabbit Lake, and Arvik are today frequently mentioned in mining publications. Twenty years ago, mining in these locations was unheard of, mainly due to logistic problems. However, improvements in the design and use of helicopters, STOL aircraft, and icebreakers in northern areas have helped to overcome these problems, making these locations more attractive to mining companies. Since 1969, when Redpath completed its first Arctic project at Texas Gulf's Scrathcona Sound property on the northern tip of Baffin Island, Redpath has been actively involved in contracting and engineering projects in three general areas: the High Arctic, Ungava and Greenland. A map showing some of these projects is shown in Figure 1. In these areas, permafrost conditions exist from a depth of 274 metres in Ungava to a depth of approximately 610 metres in the Little Cornwallis Island area, with rock temperatures ranging from -5°C to -13°C. Outside temperatures range from a low of -50°C in the winter to a high of 21°C in the summer. High winds in the winter result in wind chill factors lower than -73°C

Jan 1, 1980

By S. M. Hsiung

This paper presents the results of an extensive study concerning a series of roof falls in a room-and-pillar coal mine located in West Virginia. Three dimensional finite element modeling was employed to identify the possible causes for the roof falls. The effectiveness of possible roof control measures for alleviating or eliminating the adverse roof conditions is analyzed, discussed, and compared. The best mining alternatives are recommended. It has been found that large overburden depth and typical roof geology are the major reasons for the roof falls. Angle bolting may not solve the problem encountered in the mine studied. Changing the mine layout currently used in the mine appears to be the best alternative. The recommended pillar size and entry width which will eliminate the problem completely are 90 ft. x 90 ft. and 14 it., respectively.

Jan 1, 1985

By M. C. Rockwell

There are approximately 1,800,000 t of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a suitable source' of soil conditioner material for the local market. However, the fine particle size, 98% passing 147µm, and a high moisture content make their handling and application difficult. Agglomeration of the tailings into relatively small hard pellets was investigated and difficul¬ties were overcome. Pellets with a range of pH values and various amounts of soil nutrients and moisture content less than 10% were obtained, from tailings containing 20% initial moisture, through the addition of less than 15% selected materials.

Jan 1, 1985

By R. L. Roller

In recent years, there have been many articles and papers written on the use of specially designed belt conveyor systems in mining operations, either economic studies or actual experience. These papers generally conclude that the use of these systems can reduce overall costs from 10% to 40% over conventional methods using general purpose equipment (truck/shovel, scrapers, etc.). However, they also generally conclude that conveyor systems are inflexible and capital intensive. With the increasing cost of mobile equipment, the capital cost conclusion is losing steam, particularly when the costs of maintenance shops, road and ramp construction and other related start-up costs are thrown in. Attention here will be focused on answers to flexibility related questions, but first, a look at costs in general. Basic production economics tell us that when we have a small job to do, it is cost effective to use simple, low cost, general purpose tools which will have a minimum impact on total cost. It also tells us that when we have a large project, we can employ methods using special, relatively expensive production tools. Figure 1 illustrates what occurs on projects, of different sizes, with various quantities of production. With small quantities of work, the cost per unit of work starts out much lower using general purpose equipment, rather than using special purpose methods and equipment. However, at a relatively low quantity of work, the cost hits a lower limit and, regardless of how great the quantity of work, the unit cost can never go any lower.

Jan 1, 1985

By James J. Scott

To the safety engineer, mine planning engineer, and mine inspector associated with an underground operation, stability of the underground structure is of the utmost importance. In the United States in 1961 rock falls killed 167 miners, crippled many more, and cost the industry a fortune in lost equipment and production. Much research has been carried on to try to find ways to eliminate this loss of life and property. Within the past few years the interest in rock mechanics as a science has been at its highest point, Private industry, government agencies, universities and foundations have launched studies to gain a better basic understanding of the stability of underground openings.

Jan 1, 1966

By Francisco J. Escandon V.

Numerous lead-zinc-barite-fluorite ore deposits, with simple mineralogy and roughly concordant with bedding, are found widely distributed all over the world, having been denominated and well described as "stratiform deposits" or "strata-bound ore bodies", not having any genetic relationship. During several years, its origin has been discussed, without getting to general agreement regarding the main mining districts of this type. Through studies made of large stratiform deposits in the United States, Europe and Russia, it has been found that there are, within this classification, syngenctic diagenetic and epigenetic ore bodies. During the Symposium about the genesis of the stratiform lead-zinc-fluorite-barite deposits, carried out in New York in 1966, Frank G. Snyder (1), presented an excellent analysis of the theories of the origin of these deposits and of the evaluation of the criteria regarding classification. As per his definitions (Table 1), "a deposit is syngenetic if formed by processes similar to and simultaneously with the enclosing rock, epigenetic if introduced into a pre-existing rock and a diagenetic origin implies deposition of metals with the host sediments but with recrystallization, rearrengement and limited migration".

Jan 1, 1974

By Andrew S. Prokopovitsh

The Bureau of Mines is concerned with all the approximately 60 industrial minerals, although its research program currently is focused on 10 of them--bauxite, chromite, clay, manganese, phosphate, potash, refractories, sulfur, titanium, and zirconium. To alleviate reliance on imported materials, particular attention is directed to those minerals having a potential for production from domestic resources. Another important consideration is environmental problems associated with the production of industrial minerals, principally in mining and mineral processing operations, The Bureau also is looking at the opportunities to substitute more abundant minerals for scarce raw materials such as rutile, fluorspar, and bauxite. In its overall minerals surveillance, the Bureau's mining and metallurgical research and development are coordinated with its minerals information activities from which reviews, projections, and forecasts identify the potential for critical disruptions and short supply situations.

Jan 1, 1975