Search Documents

By R. W. Carn, D. Vincent

During the next 15 years, US coal production is expected to double, with the increased production evenly divided between the East and the West. Along with greater production, coal export markets should increase dramatically from East, West, and Gulf Coast ports. The annual overseas export capacity of US coal-loading terminals is expected to rise from 147.1 Mt (162.1 million st) in 1981 to a minimum of 278.1 Mt (306.6 million st) in 1985, according to the US Maritime Administration. Increased coal production and use will lead to more development of import and export terminals, a vital link in the coal transportation chain. With continually escalating capital costs and the competitive markets that the terminals will serve, a well designed and efficient terminal is necessary. This article begins a two-part series that presents concepts presently used in coal export terminal design. Part I looks at site selection factors and equipment needs, while Part II will examine environmental considerations in building a terminal as well as typical capital and operating costs. The world is nearing the end of the oil era. In a few years oil will not be available to sustain the growth rate and increasing standard of living we have known in our lifetime. The big question is what energy era are we moving into? With the decline of readily available oil reserves and rapidly increasing prices, many countries are trying to switch to alternate energy forms. While intensive efforts to find new oil reserves continue, alternate energy sources such as natural gas, coal, synthetic fuels, nuclear, hydroelectric, solar, and wind power are being developed. Recent indications are that coal is expected to bridge the energy gap over the next 25-30 years until the technology and economics of the alternate energy forms reach satisfactory levels. Use of coal for energy is receiving strong attention due to its long-term availability (200-300 years minimum), relative ease of development, and its low cost per unit of power produced. By the year 2000, it is expected that 25% of world energy supply will be met by direct coal combustion and possibly another 5-10% by synthetic fuel from coal. Coal's expanding share in the world energy market, along with an increase in coking coal requirements, will result in a large increase in the world's seaborne coal trade. Recent statistics and projections for the future are shown in Table 1. This phenomenal development rate includes increases in both coking and thermal coal requirements. Because of the rapid increase of seaborne coal trade during the last 10 years and the even greater projected increase of trade to 2000, various sectors of the coal industry are faced with enormous technical challenges and huge investments in equipment, land, transportation systems, and port facilities. Very large bulk terminals are under development throughout the world. Latest surveys indicate that there are about 30 new coal export and import terminals under consideration and at least 30 existing terminals have expansion programs planned or underway. With the high cost of borrowed capital and rapid inflation rates there is great emphasis on new planning and design techniques to minimize capital and operating costs of coal transportation systems. Terminals A total coal supply system can be considered to consist of one or more mines; a train, barge, truck, or other haulage system; an export terminal; a fleet of bulk carriers; a receiving terminal; and possibly, local inland distribution networks that include barges and railways. Terminals, though only a small link in the total transportation system, play a key role in overall system efficiency. At ports or inland distribution centers, terminals act as transportation links bringing trains, ships, barges, or trucks together for cargo transfer and temporary storage. A well-designed terminal can provide maximum independence between two modes of transportation and optimum freedom for intermodal interference. A terminal acts as a buffer between the two transportation modes by providing sufficient storage capacity so a ship need not wait for its cargo on, for example, a train-by-train basis, but can load immediately from the ready stock. Similarly, a train need not wait for a ship to unload its contents but can dump immediately into storage. A terminal also can be used to properly mix various types of coal to satisfy a buyer's requirements. Consider the relative value of various production and transport segments for a typical steam coal

Jan 6, 1983

By R. Poulin, R. Pakalnis, D. Peterson

Introduction A comprehensive project has been completed at the University of British Columbia that focused on the development of a commercially competitive composite cable bolt. Laboratory evaluation consisted of pull tests, preliminary shear tests, grout column testing and scanning electron microscope evaluation of the composite cable bolt. Field implementation at five underground mines throughout Canada were completed for technical and overall performance evaluation of the new product. The project began in 1989 under the sponsorship of HDRK Ltd., a consortium of mining companies including Inco, Noranda and Falconbridge Ltd. The objective was to develop a cuttable cable bolt that would serve as support for a continuous miner within a hardrock environment (Mah, 1994). The bolt was required to be cuttable by a continuous roadheader without adverse effects to equipment, personnel and the milling process. From the beginning, the focus was to employ existing cable bolt installation technology (Goris et al., 1994) whereby the cable bolts are grouted within a 4.8-cm-diam (1.08-in.diam) or larger employing a portland cement grout having a water: cement ratio between 0.35:1 to 0.4:1. The prototype, developed from Phase I, was technically comparable to that of conventional steel cable bolts. However, high cost and limited accessibility hindered its commercial acceptance. The second phase of the project was sponsored by the British Columbia Science Council and Pacific Pultrusions Ltd. of British Columbia to locally develop a glass fiber cable bolt. This phase of the project has resulted in the DAPPAM cable bolt (Pakalnis et al., 1994). DAPPAM Cable bolts are the second most used support method in Canadian underground mines after mechanical rock bolts. It is projected that 870,000 m (2.9 million ft) of cable bolts are installed annually in Canada (Poulin et al, 1994). The objective of the research program was to develop a glass fiber cable bolt with similar pullout strengths to the conventional steel cable bolts (267 kN - 60,000 lbf). More than 200 laboratory pull tests were conducted employing standard cable bolt test procedures, as outlined by the US Bureau of Mines (Goris, 1994), to assess optimum rod and surface composition, geometry, number required, pullout and shear characteristics, among others. This resulted in the DAPPAM cable bolt (Fig. 1). It consists of 10 individual 0.6cm-diam (0.25-in.-diam) rods enveloping a 2.2-cm (0.8-in.) outside diameter, high-density polyvinyl grout tube. The composite used in the construction of the rods is comprised of about 65% glass fiber within a 35% polyester resin matrix (by volume). Through pultrusion (a continuous fabrication technique), the fibers and resin are combined into a composite material. The strength of the overall composite is largely governed by the material properties, the alignment [ ] of the fibers relative to the applied load and the density and interaction of the overall components within the composite. A further modification to the composite was the addition of a sand grit to the surface of the individual rod. This increased the overall bond strength between the rod and the cement-based grout, used to solidify the cable bolt to the rock mass. The grout tube has an inside diameter of 1.9 cm (0.75 in.) and is rated at a pressure of 1.72 MPa (250 psi). During installation, the grout is pumped through the annulus of the grout tube thereby filling the hole from toe to collar. Laboratory and field trials concluded that a minimum drill hole diameter of 4.8 cm (1.08 in.) be used to ensure optimum grout coverage. Table 1 compares the design strengths (as tested) for DAPPAM vs. the ultimate strengths for a conventional 1.6cm (0.6-in.) steel cable bolt. The characteristics for the steel cable have been derived directly or indirectly by Goris et al. (1994). A design tensile strength of 289 kN (65,000 lbf) was proposed for the composite developed. However, recent tests have indicated maximum breaking strengths of more than 400 kN (90,000 lbf) (Fig. 2). Figure 2 shows the load vs. displacement pull out curves for steel and DAPPAM cable bolts. The methods of testing were standardized so as to be able to compare the results directly. The shear strength of the fiberglass cable is largely a function of the surface area sheared. Shear strengths of 89 kN (20,045 lbf) were obtained for the configuration shown in Fig. 1 when sheared normal to the axis of the cable. The testing procedure was similar to the shear tests performed on steel by Goris (1993). It is important to reinforce the implication that critical bond strength has on the success of an overall support system.

Jan 1, 1995

By R. A. Metz, Willard C. Lacy

Rather than attempting to present a summary of the many and highly varied papers that have been presented at this symposium on sampling and grade control, I will attempt to extract the general philosophy of analysis and approach, and attempt to identify the trend of future developments. First, the term "sampling" is used with its broadest connotations. A sample consists of a representative portion of a larger mass, and must represent the mass not only in the grade of contained metals or minerals, but also in all other respects in terms of mineralogy and mineral quality (1, 5), deleterious materials, recoverability of economic components, physical behavior, geophysical response (1), and even archaeological and environmental aspects (7, 11). The sample must be taken from a locality and in such a manner and quantity that it is representative of the larger rock mass. This calls for complete and accurate geological control and an understanding of the nature and distribution of the contained chemical and physical elements and a record of the effectiveness of the different sampling methods. Second, value of a given mass of ore material is based upon its profitability - the difference between recoverable value and costs to achieve recovery, beneficiation and sale. There is a strong movement in mining geology control toward more complete analysis in determining cutoff grades and in grade control, as illustrated by the kriging of metallurgical recovery factors as well as grade at the Mercur Mine (8). To achieve a "profitability factor" as a guide for economic mining practice requires further integration of: 1) the value of contained metal or mineral, 2) percentage recovery of values, 3) dilution of ore with waste rock, 4) addition to, or loss of value as a consequence of by-product materials or deleterious components, 5) cost of producing a saleable product plus minimum profit to justify the effort (cutoff), and 6) cost of land restoration (7, 11). All these parameters vary with the rock type, rock structure, mineralogy, depth, geometry, mining and metallurgical methods, but they must be sampled and analyzed if sampling and grade control are to reflect profitability. A wide variety of deposits has been presented at this symposium; each deposit with its own problems and special solutions. Deposits containing high unit-value components, e.g. precious metals and diamonds, present special problems in the obtaining of accurate samples and generally require statistical analysis control methods or may disregard or modify occasional high or occasional low values, based upon experience (12). Grade control may be accurate for the long term but may vary for the short term. Bulk sampling is always essential. Deposits containing metals or minerals with low unit value are very sensitive to transport costs, and they are often very sensitive to small amounts of deleterious components or differences in physical or chemical behavior. Problems of sampling and grade control change with the genetic type of deposit, with the stage of deposit development and with the size of the information base. Precious metal epithermal deposits (2, 6, 8), because of rapid vertical zonation and erratic lateral distribution of values, have always been difficult to evaluate and maintain grade control and ore reserves. On the other hand, evaluation and grade control are relatively easy in bulk-lowgrade deposits (4, 13). However, these deposits generally have a low margin of profit and are sensitive to mining and beneficiaton costs, price fluctuations and political costs. Industrial mineral deposits (5) often must be evaluated on the basis of their behavior, rather than by chemical analysis. Environmental impact generally increases with the scale of the operation, but certain elements or minerals have especially high impact effects (7, 11). In the exploration phase there is no production control of sampling procedures and careful geological observations are particularly essential. The greatest number of problems is related to the oxidized outcrop where the chemical environment of the ore body has changed and the contained values may have been enriched, depleted or values left unchanged (2, 6). Present evidence suggests that gold values may be very mobile under certain conditions (2, 6) and stable under others. Everything must be sampled in detail. Principal values and by-product or deleterious elements may vary dependent upon their position within the soil profile. Such factors as geomorphic position, erosion rate, vegetation, climate, etc., may affect the interpretation (1, 3). During the development phase it is equally easy to overtest, to have "paralysis by analysis," as to undertest (3, 6). Bulk samplng and testing are

Jan 1, 1992

By G. Sanders

Discussion by G. Sanders The studies reported on in this paper were initiated to draw attention to the severe contamination problem in the Section 30 drilling program at Chimney Creek. The lithologic-subset sampling study reached a different conclusion from that presented in your paper, and I wish to comment on your subsequent analysis of the data and your conclusions. Request for more complete data In the section on subsampling, you mention that the subordinate lithologies were separated and sampled, yet only the dominantlithology gold value is plotted in Fig. 4. In a contamination study, the reader is interested in the assay values for the individual subsets. Please include a table of the subsample assay data in your reply. Also, please indicate which analytical methods were used to arrive at the gold values in the subsampling study. Turning barren rock into low-grade ore Figure 5 is very revealing and typical of all of the cross sections in Section 30. Note the long strings of low-grade mineralization spread out for hundreds of feet below the ore zones. There were some very high gold values found in certain contaminated fractions during the subset sampling. The conclusion, here, was that the distinctive, strongly-mineralized dolomite layer was probably loose and crumbly and continued to disintegrate during drilling. This caused salting of the unmineralized rock samples below. Missing the high-grade part of the ore body In your statistical analysis, you directly compare the reverse circulation assays to the diamond drill assays in Section 30. Two points argue against a direct comparison and suggest the differences are greater than the 3 % that you report. First, any core loss in a gold zone most likely means that the true gold values are greater. The drillers lost significant amounts of the clay-rich, Section-30 gold mineralization. Also, the initiated salt-mud system, an attempt to improve the core recovery, met with little success. Second, the practice of not sampling core geologically, but instead sampling on even 5-foot intervals, adds a deliberate dilution to the core assay values by including a portion of nonmineralized rock in the first and last samples of each high- grade intercept. The result is often a pair of low-grade assay values on either side of a high-grade gold zone. In reality, a high-grade gold zone has a very sharp assay wall that is often bounded by barren rock. This sampling method may make the diamond-drill core assays more like the reverse circulation values and may help explain the statistical similarities you found. However, it does not represent the true gold values in the high-grade parts of the deposit. You cannot deny that, by careful geological sampling of the drill core, higher and sharper assay values will be obtained. The low core recovery and the diamond-drill-core sampling method used act together to lower the diamond-core assay values. The 3% difference you found between the reverse-circulation and diamond-core assay values could be much larger when you consider what the true diamond-drill core values would be with optimum core recovery and a geologic sampling method for the core. Should statistics have been applied here? The statement "... that reverse circulation holes have overestimated the values of some ore zones and underestimated the values of others" (p. 345) is not correct. The subsampling confirmed what the cross sections hinted at in Section 30. Namely, beneath the high-grade zones, the reverse circulation holes created, by contamination, large intercepts of low-grade ore in regions of barren rock. Because the low-grade material was not there to begin with, this is not a process of overestimating low-grade mineralization. The next statement that "the average result is similar to that of the diamond drill holes" may apply to the data set numerically, but it is not true when viewed spatially on cross sections. Adjacent reverse circulation and diamond drill holes are almost impossible to correlate, high-grade zone values vary widely and many low-grade intercepts make no geologic sense. The subset sampling and cross sections presented in the first part of the paper show that the reverse circulation portion of the data set has some serious problems, as highlighted above, and should not have been dealt with statistically at all. Conclusion Each ore body is different, and each drilling method presents unique sampling problems. In this case, the diamond drill is the

Jan 1, 1994

By Patrick Corser, Mitch Usibelli

Introduction Coal mining in Alaska's interior, specifically in the Healy area, began as early as 1918 with the construction of the Alaska Railroad. Mining was originally limited to underground operations but has expanded to entirely surface operations. In 1943, the Usibelli Coal Mine was formed and started developing Alaska's first surface mine east of Suntrana (Usibelli Coal Miner, 1984). Production from the local coal deposits has steadily increased and, in 1978, surface mining of Poker Flats was initiated (Fig. 1). Currently, a 25-m3 (33-cu yd) walking dragline strips two coal seams, using an extended bench on the second pass. In addition, a fleet of trucks and shovels are used for coal removal and some limited overburden stripping. In 1984, a contract was signed between Usibelli Coal Mine and Sun Eel Shipping Co. in 1984. Since then, production has nearly doubled to more than 1.3 Mt/a (1.5 million stpy). This article will discuss geotechnical constraints on mining within the steeply dipping coal deposits that exist within the Poker Flats mining area. Specifically, the article will describe how the mining operation retriggered an historic landslide on the No. 5 coal seam (Fig. 2). And the article tells how a mine plan was developed that allowed the coal to be safely removed without inducing additional movement. Regional geology The coal-bearing group in the Nenana coal field is of Tertiary Age. It is overlain in some areas by several thousand feet of Tertiary gravels - the Nenana Gravels. In areas mined by surface methods, the Nenana Gravels have been eroded off, and up to 30 m (100 ft) of quaternary outwash gravels overlay the coal-bearing formations. The coal-bearing group is divided into five formations: Healy Creek, Sanctuary, Suntrana, Lignite, and Grubstake (Wahrhaftig, 1969). Lignite Creek lies on the north limb of a west plunging anticline. This has brought the Suntrana coal-hearing formations near enough to the surface to allow surface mining. Mining is presently in progress on the south side of Lignite Creek in the Poker Flats area. The coal-bearing formation is cut off to the south by a fault having perhaps several thousand feet of vertical displacement, with the upthrust side to the north. South of this fault, Nenana Gravels are exposed on the surface. The Suntrana Formation contain the minable reserves at Poker Flats. This formation is a repeated sequence of poorly consolidated pebbly sandstone near the bottom, grading through a silty fine sandstone to a footwall clay unit immediately below a coal seam cap. The footwall clays are high plasticity clays to silty clays. It has been reported that they contain 30% to 50% montmorillonite (Usibelli Coal Mine Inc., 1982). There are six coal seams in the Suntrana Formation, No. I (the lower seam) through No. 6. Only the top four seams are currently exposed. No. 3, No. 4, and No. 6 seams are the only mined seams. The No. 5 seam is very thin or not present. Portions of the undisturbed Suntrana Formation are overlain by up to 15 m (50 ft) of Quaternary outwash gravels or recent landslide rubble. The surface is overlain by a very thin layer of muskeg and isolated areas of permafrost. In many areas, the outwash gravels are found immediately below the surface muskeg. Numerous landslides have been documented along the north facing slopes of Lignite Creek (US Geological Survey, 1970, and Wahrhaftig, 1958). These appear to be surficial solifluction or skin flow types of landslides. In addition, deep-seated structurally controlled slides are also evident on both the north and south sides of Lignite Creek. Structural features Premining aerial photographs (Fig. 3) of the Lignite Creek slopes in the Poker Flats area indicate substantial evidence of deep-seated landsliding. The landslides noted in Fig. 3 are both inside and outside of the current mining area. Surface mapping and geologic exploration indicate that the coal seams are dipping out of the slopes within the noted slide areas. It is suspected that, historically, these landslides were triggered by undercutting of the toe of the slopes by Lignite Creek. And sliding it thought to have taken place on one or more of the clay beds underlying the coal seams (Golder, 1985). The slide areas are characterized by semicircular head scarps and slumped topography. Based on the premining photographs, these slides do not appear to have been recently active. However, they are expected to be in a state of only marginal stability. Extensive coal exploration indicates that the primary structural feature within the

Jan 1, 1989

By Scott D. Thayer, George H. Milly

INTRODUCTION Ambient concentrations of radon and its daughter products have been measured and analyzed by a number of investigators for a variety of purposes. Principal among these purposes have been: (1) descriptive, to characterize the distribution and changes in concentrations under various conditions; (2) research in the use of radon as a tracer gas in the study of atmospheric characteristics and motions, such as eddy mass transfer, diffusivity profiles, large scale circulations, and the like; and (3) the use of radon as an atmospheric tracer in exploration for uranium deposits.* This information forms the basic data for this paper and for its placing the ambient natural, or non-anthropogenic, radon concentrations into the perspective of ambient radon health standards and lung cancer risk calculations. To enable better understanding of some aspects of the ambient radon data, review and analysis is also performed on selected measurements of radon emanation or flux from the surface of the earth into the atmosphere. These measurements have generally been made for purposes similar to those for ambient radon, i.e., (1) description of radon emanation characteristics; or (2) to support and justify the use of ambient concentration measurements in atmospheric research; or (3) in exploration for uranium. Interest is also developing in the use of such measurements for earthquake prediction. In addition, to complete the perspective, brief examination is given to anthropogenic ambient and flux radon measurements related to the mining and milling of uranium, so that comparison can he made with the values from natural sources. As a frame of reference we cite here previous summaries of studies which have presented representative values and ranges of ambient concentrations and emanation rates. H. Israel, in the Compendium of Meterorology (1951), cites eight studies of ambient radon concentrations which we have selected as representative of non-anomalous continental values. Their means generally range from [0.06 to 0.15 pCi lit-1 with the smallest reported minimum of zero and the largest maximum 0.53 pCi lit-1. The overall mean is 0.10 with a standard deviation of 0.03 pCi lit-1. Means over oceans are much smaller, and the data scarcer, with only three values ranging from 0.0004 to 0.003 pCi lit-1 and a mean of 0.0016 pCi lit-1.] Thirteen studies from Israel's list were selected as representative of mountainous terrain. These data, except for the cases of higher elevations, frequently show significantly higher values than the average cases in non-mountainous terrain described-above. The averages range from 0.10 to 0.59 pCi lit-l; the smallest minimum is zero and the largest maximum is 9.2 pCi lit-1. The overall mean is 0.30 with a standard deviation of 0.17 pCi lit-1. Israel also cites five studies of radon emanation (flux) from the earth's surface. These show a mean of 0.40 pCi-2m-2 sec-1 and a range of from 0.21 to 0.74 pCi m-2 sec-1. Data on flux are naturally scarcer in the literature than data on ambient concentrations, because of the greater interest in and utility of the ambient information. In this paper we also give special consideration to observations of the variability in time and space of radon flux rates, and to the impact of these phenomena on the use of such data for a variety of purposes. NATURAL(NON-ANTHROPOGENIC)AMBIENT RADON CONCENTRATIONS We have examined the following reports for the data selected for this category; these studies were generally intended to describe radon characteristics in the atmosphere. Jonassen and Wilkening (1970); Bradley and Pearson (1970); Wilkening (1970); Lambert, et al (1970); Pearson and Moses (1966); and DickPeddie, et al (1974). Another set of studies which was reviewed was selected because the investigators made ambient radon measurements in the course of examining the use of radon as a tracer in atmospheric research. This set consists of: Israel and Horbert (1970); Carlson and Prospero (1972); Subramanian, et al (1977); Larson (1978); Cohen, et al (1972); Hosler (1966); and Shaffer and Cohen (1972). Finally, unpublished data from uranium exploration activities (Milly and Thayer, 1976) was analyzed. [Treating the ocean cases first, the mean values are generally consistent with those quoted earlier from Israel (0.0004 to 0.003 pCi lit-1); they range from 0.001 to 0.011 pCi lit-1, with 0.003 the most frequently reported value. Continental values, from eight studies, range in means from 0.07 to 0.41 pCi lit-1 (not including mineralized areas, or "uranium country", discussed later), with maxima as high as 2.4 pCi lit -l. For comparison, the means from Israel are 0.06 to 0.15 pCi lit-1, with a maximum of 0.53 pCi lit-1. Some of these studies also present the typical decrease of-1 concentration with height to 0.01 to 0.04 pCi lit at 5 to 7 km. The vast numbers of uranium prospecting radon data of]

Jan 1, 1981

By C. A. Rawlins

INTRODUCTION Radcont is a program designed by the author of this paper for the industry to use as an instrument for radiation contamination evaluation and ventilation planning system. Radiation in mines are associated with the mining of gold and gold bearing minerals, as uranium and thorium is incorporated in the mining of these minerals. Radiation contamination in South African mines is not a new concept as it was investigated by the Chamber of Mines in the early 1960's and found not to be hazardous at the time. Since some of our mines export scrap metal to customers abroad, it came to light (1991) that some of the scrap metal was radioactive. The authority that oversees the nuclear aspects in South Africa is the Council for Nuclear Safety (CNS). They investigated these matters and found that the mines needed further information regarding radioactive material and the handling of these contaminated materials. As the various mines were licensed (with various conditions incorporated) thereafter, the mines had to do their own investigations as to what extent their properties (Surface and underground) were radioactively contaminated. Some mines were found to be highly contaminated over the years of operation and controlling conditions were installed and measures installed to reduce the contamination levels. One of the conditions when issuing a licence by the Council for Nuclear Safety (CNS), is that a screening survey be carried out to determine the radiation exposure levels and corrective action to be taken if necessary. These surveys must be done by a person trained in the required procedures for such a survey. The person must also measure the risk correctly and assess the results properly. In such a survey, the internal and external exposure levels must be determined to assess the total exposure of persons working in those conditions and take appropriate action if necessary. When doing such a survey, hundreds and more likely, thou- sands of data points are recorded. In order to assess the data recorded, various integrated and difficult calculations need to be made, and takes up enormous amounts of time. (This excludes the interpretation of the results ) The following explanation of the program shows the different parts of such a survey assessment calculations to be done. The paper details the program layout and the different sub- sections within the primary program. It must be stated that the program, as with any other program, is as accurate as the data inserted into the data base. The program and details thereof are given under the following headings: 1. TOTAL EFFECTIVE DOSAGE WITH REGARDS TO: • GME required gravimetric results obtained (mg/m3) • Thick layer or total contamination measured (Bq/m2) • Dry condition surveys with dust loads taken as a Standard l0mg/m3 • Wet conditions survey with dust loads taken as l mg/m3 • Airborne long lived alpha and beta activities as determined by analysis in Bg/m3 • LTD (Thermoluminescent Dosimeter). Results as obtained from the SABS (South African Buro of Standards) are recorded in this section for each month of the year for each individual worker. An average dose is then determined at the end of the year. • Bucket measurements as recorded. • Smear samples (Loose contamination). As determined by Electra or by analysis • Occupational factors for Metallurgical and Engineering occupations in and around the Metallurgical facilities of your mine. • All underground dosage determination and calculations. (Radon and Thoron) 2. INFORMATION REQUIRED WHEN PROGRAM IS INITIALISED: As the program is started, it opens up on the contents page. Here there are various options to choose from, but one is cautioned as a beginner in operating the program, not to perform any tasks before carefully reading these instructions. Firstly, one must go to the 'Information required" pushbutton. Press this button. The information required page is shown where the cursor can be moved to the block where one can enter the specific mines name. To enter a mines name, put the cursor in the block provided and just insert the mines name with the normal keyboard keys and press the enter button on the computer keyboard. To enter the other information required such as Alpha and Beta instrument efficiency, ALI (Annual limit of intake) and probe area, one can either press the 'Data required" button for a dialog box information or enter it manually by just putting the cursor in the block provided and entering as did above. In order to insert all the required information for the pro- gram to calculate the information required, one must proceed further by entering the area names surveyed in the spaces provided. There are 20 spaces to enter 20 different areas surveyed. One must further also provide the amount of days worked in each area (i.8. 250) in the block provided. The de- fault is 250 days. There are also standard information given in the information data page such as breathing rate (1,2 m31h), 8 hours worked per day, 5 days per week and 50 weeks per

Jan 1, 1997

By M. R. Yalamanchili, J. D. Miller

Discussion by M.R. Yalamanchili and J.D. Miller The authors, M. S. Celik et al., should be recognized for their efforts to describe the flotation behavior of boron minerals. In the case of borax and other soluble salt minerals, analysis of the flotation chemistry has been difficult because of the high ionic strengths associated with these soluble salt systems. However, considerable progress has been made in this area, and recently a surface charge/collector colloid adsorption model was proposed by Miller and his coworkers to explain the collector adsorption phenomena observed in soluble salt flotation systems (Milleret al, 1992; Yalamanchili et al., 1993; Miller and Yalamanchili, 1994; Yalamanchili and Miller, 1994a: Yalamanchili and Miller, 1994b). In this work, the sign of the surface charge of alkali halides in their saturated brines was established on the basis of nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis (Miller et al., 1992). Generally, these results are what would be expected from the simplified lattice-ionhydration theory. This electrokinetic information coupled with the stability and prevalence of collector colloids in such soluble salt flotation systems indicates that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Experimental flotation/bubble attachment results for 21 different alkali halides (Yalamanchili et al., 1993; Yalamanchili and Miller, I994b) confirmed that the flotation response of soluble salt minerals with weak electrolyte collectors can best be explained by the adsorption of oppositely charged collector colloids rather than by the adsorption collector ions and/or neutral molecular dipoles as originally suggested by many researchers (Fuerstenau and Fuerstenau, 1957; Schubert, 1967; Roman et al., 1968). In addition, the flotation of certain alkali oxyanions (Pizarro et al., 1993) and double salts such as schoenite and kainite can be explained by the same collector colloid adsorption mechanism (Miller and Yalamanchili, 1994). The borax flotation results reported by Celik et al. need to be examined in terms of the above mentioned surface charge/ collector colloid adsorption model. Unfortunately, the authors seem to be unaware of this recent work that nicely describes soluble salt flotation with weak electrolyte type collectors such as amines and carboxylates. In view of our past work, the flotation characteristics of borax were of particular interest, and, in this regard, the results of dodecyl amine flotation of borax reported by Celik et al. have been examined in further detail in the light of experimental results from our laboratory. In our research, a vacuum flotation technique was used to study the flotation response of borax (Na2B407.10H20), which has a solubility of 39 g/L at 25 °C) with dodecyl amine hydrochloride as collector. These chemicals were purchased from Eastman Kodak and used as received. Saturated solutions of borax at desired pH values were prepared by continuously stirring the salt solutions over a period of about 10 hrs. It should be mentioned that the conditioning time to achieve equilibrium is an important variable and can significantly change the flotation response of some soluble salts (Yalamanchili et al., 1993). Collector was added to the saturated borax solutions containing about one gram of 100x 150 mesh borax particles, and conditioning was done for about 20 minutes prior to flotation. The borax flotation recoveries from saturated brine are presented in Fig. 1 as a function of collector addition at the natural pH of 9.3, as reported both by Celik et al. and as measured in our laboratory. In addition, the region of precipitation for the dodecyl amine hydroborate is included in Fig. 1. It can be seen in Fig. 1 that the flotation response curves are separated by about one order of magnitude in R12NH3CI collector addition. The flotation results of Celik et al. show that the maximum borax recoveries can be obtained below the solubility limit of the dodecyl amine hydroborate collector. However, in our experiments borax flotation seems to occur only after the precipitation of the dodecyl amine hydroborate collector as might be expected from the collector colloid adsorption model (Yalamanchili et al., 1993) if borax were negatively charged. Further analysis by nonequilibrium and equilibrium electrophoretic mobility measurements for borax indicates that borax is negatively charged at the natural pH of 9.3, as discussed below. The reliability of the nonequilibrium electrophoretic measurements has been demonstrated previously for alkali halides and alkali oxyanions (Miller et al., 1992; Miller and Yalamanchili, 1994). The equilibrium and nonequlibrium electrophoretic measurements for borax were found to be consistent and are presented in Table 1. These results provide clear evidence that borax carries a negative surface charge in its saturated brine (pH 9.3), and the sign of the surface charge of borax reverses and becomes positive if the pH is reduced to 8.6. The equilibrium between borax and its saturated brine can be described by the following reaction: [2Na2B407.1OH2O-4Na++B407=+HB4O7 +OH+19H20] It appears that the oxyanions of the borax lattice provide

Jan 1, 1995

By Richard E. Ray

INTRODUCTION Main mine fan installations at underground coal mines must be designed to comply with the requirements outlined in 30 CFR (Code of Federal Regulations) Part 75. However, very little emphasis is typically placed on the aerodynamic optimization of shaft collar designs, ductwork configurations, and the selection of a fan isolation, or "closing door," system. Field testing has shown that poorly designed systems may produce large pressure losses between the shaft and fan inlet, as well as air turbulence problems which adversely impact fan efficiency and sometimes fan structural integrity. This paper analyzes each component of a surface exhaust fan system for an underground coal mine: • The shaft collar arrangement, • The 45 or 90-degree turning duct that isolates the fan motor from the return airstream, • Alternative ductwork arrangements for parallel fan installations, • The self-closing doors or dampers that are required for multiple fans, and • Horizontal and vertical evas6 arrangements on the discharge side of the fan. While discussion is limited to axial fan installations at shaft mines, most of the recommendations would also apply to centrifugal fan installations and to main mine fans for drift mines. FEDERAL REGULATIONS The mandatory safety standards for underground coal mines that apply to the installation of main mine fans are listed in 30 CFR Part 75.310. Stipulations which impact the design of the fan sys- tem arrangement are contained in paragraphs (a)(l), (a)(5), (a)(6),(d), and (1) of 75.31 0: • Each main mine fan shall be installed on the surface in an incombustible housing; • Each main mine fan shall be protected by weak walls or explosion doors in direct line with possible explosive forces; • Explosion doors or weak walls shall have a cross-sectional area at least equal to the area of the return air shaft or drift opening through which the pressure from an underground explosion would be relieved; • Each main mine fan shall be offset by at least 4.57 m (15 feet) from the nearest side of the mine or shaft opening; • Automatic closing doors shall be provided to prevent possible air reversals through the fans in mines ventilated by multiple main mine fans. The installation of main mine fans underground is prohibited by 30 CFR Part 75.310, (a)(l). Providing explosion doors or weak walls in line with a possible underground explosion and offsetting the fan 4.57 m (1 5 feet) from the edge of the shaft preclude the installation of the fan directly over the shaft. In addition, 30 CFR Part 75.507-1 specifies that all electrical equipment used in return air courses be permissible, which requires locating the fan motor outside of the airstream exhausted through the fan. To comply with the Part 75.310 regulations, explosion doors are typically located directly over the shaft as part of the shaft cover or 'bonnet." A sufficiently long section of ductwork placed between the shaft enclosure and fan, equipped with a 45 or 90- degree turn, enables the fan to be offset at least 4.57 m (1 5 feet) from the shaft and the motor to be isolated from the airstream. The need for the turn in the ductwork can be eliminated by driving the fan from the discharge side, instead of from the inlet side, and providing for a 90-degree bend in the evas6. For multiple main mine fan systems, self-closing doors can be located on the inlet or discharge side of the fan. FAN SYSTEM COMPONENTS A poorly designed exhaust fan arrangement will produce turbulent conditions at the fan inlet and significant pressure losses between the shaft and fan. Field tests have shown that pressure losses through inlet ductwork at some installations may constitute as much as 30 percent of the total mine head. Unfavorable flow conditions may cause a change in the operating point on the fan performance curve, resulting in reduced fan efficiency and pres- sure generation capability. In some instances, poor airflow distribution through the fan may create mechanical stresses that lead to fan blade or fan housing fatigue failures. The objective in designing an air duct arrangement for a fan system is to provide a low cost duct that will move the air from the shaft to the fan in a uniform air distribution and with minimum energy requirements. The optimum solution is a compromise between technical and economic factors. Aerodynamic design considerations for the shaft collar and cover, fan inlet ductwork for both single and parallel fans, self-closing doors, and evas6 are discussed in the sections below. Shaft Collar/Cover To prevent excessive turbulence and non-uniform air distribution through the fan, a smooth transition for the change in direction of airflow at the top of the shaft must be provided. However, the concrete lining of the shaft is abruptly terminated at the surface at many coal mine installations (see Figure I), creating a sharp 90-degree bend. The airflow exiting the shaft becomes heavily concentrated in the upper portion of the horizontal fan in-

Jan 1, 1997

By A. J. Richardson

Before the development of the underground stoping and mining costs can be considered, certain facts about the ore body, the proposed mine, markets, etc., must be known or determined. In the case to be studied, the zinc-lead mineralization occurred with a narrow vertically dipping structure of undetermined length and vertical extent. Exploration completed to date has revealed 6.5 mil¬lion st t of proven reserves. A further 820,000 st of in¬dicated reserves has been outlined and this tonnage is considered capable of being expanded by a factor of approximately four after more detailed drilling. After studying the market conditions and completing a very preliminary feasibility study, it was decided that production would be 730,000 stpy (or 2000 stpd) of ore. First year production would be at the rate of 1500 stpd. The main design criteria for the selection of the min¬ing methods are minimizing surface subsidence, maxi¬mum recovery of the ore body, maximum degree of grade control, maximum productivity, and safe working conditions. Two basic extraction systems are considered capable of meeting these requirements: mechanized cut¬and-fill stoping and sublevel long-hole stoping with filling. The primary development system of the mine has been designed to give maximum flexibility in stoping systems and layout and to permit changes if considered necessary as a consequence of actual production ex¬perience. At the present time, access to the mine is by a circu¬lar concrete lined vertical shaft, 16 ft diam, sunk to a depth of 1380 ft. Two exploration levels have been driven within the ore zone at depths of 165 and 1246 ft below the surface outcrop. The development to date had the objective of sampling the mineralization and produc¬ing detailed information on the outline of the ore body and the distribution and controls of zinc and lead values. In an attempt to satisfy the basic design criteria for the mine, it was decided that production would be best achieved by a combination of 40% sublevel long-hole stoping and 60% cut-and-fill mining. Costs of exploration and capital development of per¬manent underground facilities are normally written off over the life of a mine. Production expenditures, on the other hand, are of a temporary nature and are normally charged as and when incurred as an operating expense. Reasonably accurate predictions of mine production costs can be built up from engineering design and estimates of individual mine activities for ultimate inclusion in the comprehen¬sive data required for financial decision making. The simulated operations can be costed on a detailed basis in the form of a monthly operating budget. The budget format can be generalized or detailed, depending upon the scope of the project. However, ex¬perience suggests that a fairly detailed format has the advantage of assuring that all significant cost items are included. For underground costing it is suggested that the budget structure include five major cost centers (i.e. development, diamond drilling, ore extraction, hoisting/ transportation, and general mine expense). These in turn are detailed under numerous subheadings. The mechanism for compiling an operating budget will be illustrated. Because of its relative simplicity, ore extraction under sublevel long-hole stoping has been chosen for illustration. All other activities, simple or complex, can be estimated in similar fashion. BLOCK AND STOPE DEVELOPMENT Long-hole blocks, used where advantageous, will be up to 250 ft in height, depending upon the vertical con¬tinuity of the mineralization, and approximately 300 ft long. Drawpoints will be at 36-ft intervals and serviced by loading crosscuts driven from a footwall drift parallel to and close to the ore zone. Pillars between the stopes will be 50 ft wide. Stopes will be drilled off with vertical rings of blastholes drilled from sublevels approximately 60 ft apart vertically. This drilling will be done by percussion drilling machines (31/2 in.) mounted on a trackless drilling rig. Load¬haul-dump (LHD) equipment will be used to move broken ore from the drawpoints to the orepass connecting to rail haulage systems. On completion, long-hole stopes will be backfilled to prevent caving and to facili¬tate later pillar removal. From a planned stope layout, a forecast of produc¬tion and development is made in Table 1. Table 1. Block Tonnage and Stope Development Quantity Ore Waste Total ore block 375,000 st 2 stopes 310,000 st 1 pillar 65,000 st Access crosscuts, 4 at 100 ft 400 ft Drill sublevel drifts, 6 at 300 ft 1800 ft Stope raises, 3 at 250 ft 750 ft Undercut sublevel drifts, 2 at 300 ft 600 ft Loadout crosscuts at 35-ft intervals 550 ft 100 ft 3300 ft 500 ft Total development footage 3800 ft Tons per ft of development 987 st

Jan 1, 1982

By D. T. McMurray

INTRODUCTION Shabanie mine, situated some 180 km east of Bula¬wayo, has been a producer of chrysotile asbestos for more than 50 years. The ore bodies occur in serpentinized dunite, which overlies talc-carbonate schist. A zone of relatively competent rock of varying thickness occurs between the schist and the ore bodies, which are gen¬erally less competent. The hanging wall of the ore bodies is economic, and the hanging-wall serpentine carries a variable subeconomic amount of fiber. It is important to note that, in general, the ore body competence is less than that of the foot and hanging-wall formations. Historical After surface operations ceased, cut-and-fill stoping was used to win ore from underground; this was success¬ful until the increasingly stoped-out area caused insta¬bility in the stope pillars and back. Consequently, dur¬ing the early 1950s, a gradual change to cave-mining methods was made, the ore being won by hand lashing in drawpoints, situated in the basement of the stope blocks, and passed through orepasses under gravity to the haulage level some 13 m below. About this time, interest was focused on the sub¬level caving method in use in Swedish iron ore mines: it was felt that it might be applied economically to the Shabanie ore bodies. Accordingly, in 1958, an experi¬mental stope block was laid out in which sublevel inter¬vals and extraction tunnel spacing were 9 m. The tun¬nels (ring drilling drives) were oriented on strike-in contrast to the Swedish system, in which crosscuts that retreat from hanging to footwall are used. The advantages of the method were quickly appre¬ciated by the operating personnel and, despite the in¬evitable teething troubles pertaining to the introduction of any new mining method, it was not long before sub¬level caving was providing a high proportion of the mill feed. The disadvantages also became apparent at an early stage, however, and, from that time to the present, continuing modifications have been made to mining lay¬outs in an effort to improve ore recovery. GENERAL DESCRIPTION OF METHOD The mine is served by a vertical hoisting shaft, in which two skips, a man cage and a service cage, provide adequate capacity for production requirements. The rock hoist is a Ward Leonard control hoist, in which two electric motors drive a common gearbox. The man winder is driven by an a-c motor. Several auxiliary shafts provide secondary egress and intake and return ventilation. Main haulage levels are above (Fig. I a and b). Blasthole fan patterns are drilled by drifters of 100 mm bore, drilling 41-mm holes; when a sufficient strike length has been drilled, a slot is cut in the upper¬most sublevel and the rings are broken into the slot. Initially, a limited tonnage is drawn, since it is essential to ensure that the hanging wall caves behind the retreat¬ing stope face. Once this has been established, maxi¬mum tonnage can be drawn, as described later in this chapter, under the heading "Draw Control." The broken rock is loaded by 0.14 and 0.20-m3 load¬ers into cocopans (rocker-dumping type of tipping truck), which are hand trammed to orepasses, discharg¬ing on the haulage where 11-t electric trolley locomo¬tives haul 3.95-m3 Granby cars to the main shaft bins. As is evident from Fig. 1, the layout is simple, the block is brought rapidly into production, there is a high degree of selectivity and flexibility, and the result is a low-cost high-productivity mining method. DEVELOPMENT Main haulages are developed at 3.2 x 3.2 m, and once the service winze connections have been completed the development of the sublevels is undertaken. The footwall drives are cut first, to obtain access to the block. These ends are of the standard section, 2.4 x 2.8 m, and from them crosscuts at intervals of 70 m are driven through the ore body to the hanging wall. These crosscuts are used to supplement the geo¬logical information previously obtained from diamond core drilling, and they provide additional and more de¬tailed data on fiber percentages and lengths, structural features, and other relevant criteria which are used to build up the geological assessment of the area and to classify it in terms of the geomechanics rock classification (Laubscher and Taylor, 1977). The crosscuts also allow the necessary orepasses to be sited conveniently so that tramming distances from the loading points are not excessive. Development Drilling Once the skeleton development has been completed, the extraction headings are developed at 2.4 x 2.4 m as shown in Fig. 1. Standard development practice is to use crews of a machine operator and his helper, equipped with air-leg mounted jackhammers, to drill rounds of 1.8 m with integral tungsten carbide tipped drill steel. The round drilled is a normal drag round, as shown in Fig. 2, but considerable attention is paid to the drilling of the perimeter holes to use effectively the

Jan 1, 1982

By A. J. Kroha, N. Wesis

Most copper mines produce both ore and low-grade "leach" rock or acid waters that contain recoverable copper. The sulfide ores pre¬dominate, and a portion that is too low grade for milling to produce concentrates for smelting, but has to be mined and trucked away anyhow, may be leached successfully with acid in dumps. Most of this leach material consists of sulfides and silicates or carbonates, and if the gangue is such that it consumes a high quantity of acid, this factor may rule out a leach operation. There are also valuable deposits that contain mostly acid-soluble copper, or occasional sulfide ores from which a sulfide concentrate can be roasted and acid-leached to produce a copper-bearing solution. Finally, there are milling ores in which the lesser part of the copper is acid-soluble and can be precipitated with iron or synthetic inorganic precipitants that produce metallic copper or copper sulfides that will float with the sulfides. Ordinarily, ores that contain copper associated with the sulfur ion, such as in the minerals chalcopyrite, chalcocite, bornite (and others), are milled to produce a 25-30% Cu concentrate for smelting, while a lesser amount of acid-soluble copper may be converted from solution to cement copper on iron scrap. A fast-growing percentage of such copper, however, is removed from solution with exchange resins or organic compounds in organic carriers such as kerosene (solvent extraction), then eluted with strong acid and subjected to electrolytic precipitation either in marketable form or as anodes that can be refined further. From the point of view of conventional copper smelting, copper flotation concentrates and cement copper are of chief interest in this chapter. Table I is a condensed open schedule for concentrates that generally run between 25 and 35% copper, and much less frequently as low as 12-15% or as high as 65-75% copper, the former being due to intimate relationship with pyrite (like the former United Verde Extension), and the latter representing such ores as the Bolivian Coro¬coro ore in which the copper is in the form of chalcocite in sandstone. These extremes are no longer common. When they occur, a special purchase schedule has to be negotiated. Included in Table 1, copper precipitates (cement copper) generally run from 70-85%a copper, and the same basic purchase schedule is used as with flotation concentrates. Sulfide Flotation Concentrates The sulfide copper concentrate produced in the mill as a flotation froth, with water then added for transportation of the heavy mineral particles from the flotation cells to thickeners, may run 60-80% water by weight, and the removal of water down to 25-50% by weight by means of thickeners, followed by further dewatering by continuous vacuum filters to 7-18% moisture by weight (depending on size of solids by screen analysis and also by content of clay) is a critical operation. Mill operators would like to produce a filter cake with 7-9% moisture content, but even with the help of steam on the filter this desirable condition is seldom realized when the concentrate is as fine as 80% -325 mesh. More commonly, the final concentrate is reground in pro- to produce best copper recovery and grade of concentrate (or molybdenite separation). In those cases, increasingly frequent, the filter product may not be a cake at all, but a mud that is hard to handle-even requiring a thermal dryer. Greater difficulty of form¬ing a manageable cake often comes from the copper-molybdenum separation by flotation, because the alkaline sulfides and hydrosulfides, or cyanide, or other similar reagents used for the separation, may leave the now relatively molybdenite-free copper concentrate even more difficult to filter. Handling a wet filter cake is difficult enough when its destination is only a short distance away-a matter of yards rather than miles. In those cases the filter cake may be thermally dried near the point of production, using rotary or multiple hearth, or fluidized-bed dryers. Alternatively, the concentrate may be pumped or carried in slurry form to the smelter and filtered there, or it may be spray-dried and compacted. For transportation to a smelter just a few miles to a few thousand miles away by ship or railroad other factors may be important, such as: in shipping by sea, avoidance of spontaneous combustion; in shipping by rail, losses by leakage if too wet or by wind and sun if too dry. It is the responsibility of the millman-usually the mill superinten¬dent-to make sure that his concentrates are in satisfactory condition when they leave the mill so that they meet these requirements: 1) They must have been accurately sampled and dry-weighed, the latter meaning that a moisture determination and gross weight must have been taken. 2) They must be dried sufficiently when necessary to prepare them for safe transportation. 3) They must arrive at the smelter with reasonable likelihood that they can be check-weighed and sampled fairly and equitably,

Jan 1, 1985

By Aladar B. Dory

INTRODUCTION Anyone familiar with the problems of hardrock mining will agree that the majority of the serious dangers present in mining are quite visible and obvious to any person reasonably familiar with the profession. Having unsecured, unscaled back over ones head, gives one a very good chance of ending up under a caved in mass of rock. Staying too close to a blast gives one almost a certainty of being hit by a flying rock. Too little oxygen in the air will very quickly lead to loss of consciousness and death. One walks only so much over deep, unsecured openings before he falls into them. It is because of this clear visibility of the conventional health and safety hazards that mining regulations in almost all jurisdictions world-wide are a more or less comprehensive collection of "shalls" and "must nots" of good common sense. When basic rules of common sense safe working practices are at stake, there is little room for dialogue and compromise. The mine inspector is then observing, during his inspection, how well the mine follows these common sense rules. RADIATION AS A HIDDEN DANGER Radiation in mines is a risk, the impact of which does not demonstrate itself immediately. It is first of all a potential risk. Two individuals exposed to identical radiation will almost certainly be effected differently, if at all. This is certainly true of exposures and doses one might encounter in the mines today. We hear very often the phrase: "there is very little known about the effects of radiation". It is one of the most misused and misunderstood half-true statements. I would doubt that there is any other carcinogen whose effects have been studied as extensively as the health effects of radiation. Where the statement is correct is regarding the knowledge of the quantitative assessment of the risk of low level radiation exposures. The reason for this uncertainty is that the magnitude of their health effect is very close to the health effects of natural radiation, cosmic radiation and the effects of other carcinogens such as industrial pollution, hydrocarbons from cars and other chemicals we have grown accustomed to using. As far as lung cancer is concerned, the effects of wide use of tobacco probably outperforms any other single substance. All this having been said, the bottom line is still unchanged. Radiation exposure, in most cases mainly radon daughter exposure, was and still is one of the health hazards of uranium mining and as such has to be controlled to the best of our ability. Various jurisdictions have adopted different approaches to the control of radiation exposures of uranium minemill workers. The following sections of this presentation will attempt to explain the regulatory approach taken in Canada. THE CANADIAN REGULATORY PHILOSOPHY As indicated earlier, the health effects of low level radiation are quantitatively not yet defined and no proven threshold of radiation exposure exists. The Atomic Energy Control Board's (the Board's) regulatory system is based on the basic assumption that there is no absolutely safe limit of radiation exposure below which there are no health effects. Theoretically we should therefore strive to reach zero exposure. It is obvious that this objective cannot be reached in real life. The objective of the regulatory process therefore has to be to achieve radiation exposures of the workers that are as low as reasonably achievable, social and economic factors taken into account. This, of course, is the internationally acclaimed ALARA principle put forward by the International Commission on Radiological Protection (ICRP). To avoid any misunderstanding it is worth emphasizing that the ALARA principle is applied to achieve exposures below the regulatory limits which must not be exceeded in normal operation of any nuclear facility including uranium mines and mills. The present regulatory limits for radiation exposures of atomic radiation workers are based on the recommendations of the ICRP and they are almost universally accepted. They should ensure that the risk from radiation exposure is not greater than the risk associated with working in a comparatively safe industry. Basically, there could be two extreme approaches to the regulation of uranium mining and milling. One extreme approach is to develop very extensive and detailed regulations and requirements covering all aspects of radiation protection. This is a somewhat autocratic approach to the regulatory process. This approach has two very serious shortcomings. If detailed requirements are set in regulations, due to the great variations of actual conditions at various mine-mill facilities, they have to be set as a compromise between the desirable requirements and those which could be met by practically all facilities. This approach takes away from the management of the facilities the initiative to strive for improved conditions. Requirements are spelled out in clear, understandable targets and the only worry of the management is to comply with these targets. One of the basic duties of management is to manage the operations in the most effective way with the maximum health and safety of the workers in mind.

Jan 1, 1981

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By Friedrich Steinhäusler

RADON SOURCES AND CONTROL MEASURES IN THE MINING ENVIRONMENT Most of the contamination of the mine atmosphere by radon 222 is due to radon emanating from solid or fractured ore surfaces of walls, roof and floor. Also radon gas emanates from broken ore either from storage in backfilled mined-out areas as applied in e.g. shrinkage stopping methods or from ore spillage along intake airways mainly due to the use of trackless haulage. To a lesser extent water itself can represent an additional source of radon, which emanates into air from open drainage ditches or seepages along intake airways. The contribution from water can be controlled effectively by isolating the water from the primary intake air system, e.g. by diverting the water through pipes and/or sealing of seepages by grouting. However, control of radon emanating from rock surfaces creates a major technical problem with significant impact on the economic aspects of mining operations, if adequate radiological conditions must be maintained. Basically this can be achieved by suppressing the emanation process itself, confining already emanated radon or by removal of radon from the mine atmosphere. Extensive research has been carried out on the rate of radon emanation as a function of barometric pressure changes (Pohl-Rüling and Pohl, 1969). It could be shown that the radon supply consists of a permanent and variable component. The former results from the surface of the rock and depends mainly on the emanating fraction of its radium 226 content; the latter originates from within the rocks and is a function of the suction effect of decreasing barometric pressure, rock porosity and fissures. The practical application of this barometric pump effect for depressing the rate of radon emanation, e.g. by pressurizing the mine atmosphere, is limited due to high costs for providing a sink for absorption of radon and air as well as lack of permeability in most uranium ore bodies (Schroeder et al., 1966). Mine air cleaning by removal of radon can be achieved with the use of cryogenic methods, chemical removal, adsorption into charcoal beds, use of a gas centrifuge or general ventilation techniques. Technical problems have so far prevented the application of any of these methods other than ventilation. It is common practice to use the age-of-air concept, i.e. fresh air is delivered to the worker as directly as possible and removed quickly afterwards thereby maintaining the air "young". Engineering principles for quantity distribution of air through underground working areas are straightforward for general mining situations where radon constitutes an environmental contamination problem. However, in cases of high uranium ore content this concept may result in high costs with regard to installation and energy requirements for effecting both frequent air changes as well as sufficient heating of the air in cold seasons. Taking into account that the investment in ventilation systems is a major cofactor for the overall ore production costs this can be a limiting and decisive component in the assessment of the economic feasibility of specific mining operations and mineral reserves in general. Effective control of the radon flux from the rock surface prevents the initial contamination of the mine air with radon directly at the source. A radon diffusion barrier for practical application in mining requirements should fulfill the following requirements: - reduction of radon emanation rate by at least an order of magnitude - high mechanical strength - ease of sealant application onto surface to be coated - water resistant - low fire hazard - resistant to temperature changes encountered in mines - high cost efficiency in relation to exposure reduction achieved (direct and indirect costs) - low degree of maintenance. In the past several materials have been tested as sealants for controlling the emanation of radon from surfaces of rock and building materials. Epoxy paints reduce radon emanation rate only by a factor of 2 to 6 (Auxier et al., 1974; Eichholz et al., 1980; Keith Consulting Engineers, 1980). Although it is possible to prevent the escape of more than 99 % of the radon to the environment with gel seals over 80 mm thick (Bedrosian et al., 1974), practical applicability is very limited. Multilayer coatings of epoxy resins with various additives require meticulous preparation and flawless application of seamless four-layer coatings in four days to impede radon diffusion (Culot et al., 1976), otherwise results from this method have not been totally satisfactory (Leung, 1978). Aluminium foil laminated with polyethylene and paper on each side is under test as radon barrier but results are not available yet (Ericson, 1980). However, this method has the inherent disadvantage that possible malfunctioning electrical installations can cause fire or electrical shock through the sealant. Polyurethane foam coatings have been used on stoppings as very effective sealants. It does, however, represent a potential danger of spontaneous ignition and it is expensive (Rock, 1975). Thus, there is still need for a material which has similar properties as outlined above. In the following results are reported from investigations on the suitability of various materials as radon diffusion barriers.

Jan 1, 1981

By John E. Bailey

The advent of Nuclear Energy has caused a phenomenal growth in the uranium mining industry. To keep abreast of this surge the mining industry has located many ore bodies, determined the best types of mining adaptable to this particular type of ore and developed a highly specialized type of operation. But, has the mining industry gone far enough in the planning? Has ?built-in? safety been included in the efficient methods of operation? Preplanning safety in the mining industry, as in all industries, takes engineering and ingenuity combined with the experience and cooperation of all concerned. A system of mining can be planned on a map and it will look good. However, when the actual mining takes place, conditions may be such that deviations from the original plans may be required because of excessive water faults or other conditions encountered. With safety we may also be required to change, to conform to the characteristics of a particular operation. People in the mining industry are well aware that loose back has killed miners each year. This condition occurred in practically all types of mines. The condition is not new to us. It is also known that explosives, haulage, machinery and conditions common to all types of mining have taken a heavy toll of human life in mining. In addition to these hazards in the uranium mines, the hazard of radon is also present, Radon is a radioactive gas liberated from ores containing radium. This gas is released into the active workings by the blasting or breaking up of the ore. Sometimes it is caused by radium contaminated water seepage from abandoned workings or from the ore body itself. Until the action of this gas on the human was known, many miners were affected. Un- less adequate precuations are taken to protect the people in these mines,, they may be exposed to this hazard, Health researchers made a study of this substance to determine how it would affect the health of the men, They also studied men who had worked in previous years, in mines known to have contained radioactive materials. All of this research contributed to the present knowledge of radon and its daughter products. It is not flammable nor explosive, but, if allowed to enter the body through the respiratory organs it can cause serious damage. Mines have been operated in the past and are still being operated, which were known to contain explosive and noxious gases, indicating that this problem can be controlled. Several states have instituted laws that make it mandatory to provide adequate ventilation and use of monitoring devices to limit radon and its daughter products to a maximum of 300 micro-microcuries per liter of air. This is considered a safe limit for sustained periods of human exposure. While the findings of research do not prove conclusively that the inhalation of excessive radon or its daugher products cause lung cancer, indications point to this as a possibility, particularly radium A and radium C1 of the daughter products. The threshold limits set by law in most uranium producing states are believed to be safe. In a few years, when tests and data now in the process of collection by interested state officials and laboratories is complete, these limits may be found to be ready for revision. Studies such as these take time. At present, the limits that are used are based upon estimates. The permissible limits of exposure to radon and daughter products include a large safety factor. It is considered that a good supply of fresh air delivered to the working places, adequate dust control, the sealing of unused or abandoned workings, the removal of mine water which is generally contaminated and a safe waiting period after blasting, will hold to a minimum the dangers from this source. There are, of course, problems accompanying each of these procedures. For example, the ventilating of untimbered raises and bringing fresh, uncontaminated air to the working places may be a problem. However, a good mining man can solve these problems as they apply in each particular operation. From the information available at the present time, the daughter products containing polonium and emitting alpha radiation, may be a health hazard. Fortunately, the half life of most of the daughter products is short, however, radium D has a half life of 22 years and presents a problem of contamination in the storage of old tailings. So we can see that failure to comply with the accepted good mining practices may have harmful effects on the health of miners. It is gratifying to note the interest in this potential hazard by the officials in the uranium ore producing states, who are making extensive studies and keeping records of the men who work in this type of mining. This all provide information necessary for preplanning safety. By contrast, little has been accomplished to control the injuries and deaths from some other factors connected with most underground mining operations. I would like to discuss briefly one of the hazards which take an annual toll in our underground mines, this is falls of back and walls. This problem or hazard is present, and will be

Jan 1, 1958

By R. M. White

Abstract. Gulf Coast Salt Domes are being considered for radioactive waste disposal and this paper describes the geophysical techniques currently being used and those being considered for later phases of the program. Detailed gravity work utilizing a modification of the Talwani-Ewing modeling technique, shallow high resolution reflection seismic surveys using the mini-sosie concept, surface electrical resistivity and down-hole geophysical logging to add a third dimension to all of the surface techniques and to allow inverse modeling of the surface data sets are being utilized. The logic of the combined geophysical surveys will be discussed as well as their relative economics and their relationship to the overall exploration effort.

Jan 1, 1980

By A. T. Yu

Bulk sampling is define' as the ?process of extracting a small fraction of material from a large bulk ...sufficiently representative ...for the intended purpose.? (ref. 1). Today's pressing need for simple, effective and reliable sampling systems is intensified by the growing demand for quality control as a means to cope with inflation, competition and rapidly increasing consumption of raw materials. Much has been written on bulk sampling (ref. 2 thru 9). It involves a wide range of subjects cutting across the domains of physics, chemistry, geology, mining, materials handling and processing, as well as probability and statistics. Since the problem itself is complex, any in-depth treatment cannot avoid a somewhat lengthy coverage. Of all of the related topics. Arbitrary, haphazard studies, on the other hand, can leave out important details and obscure or confuse the issue.

Jan 1, 1970

By William R. Bond

The pressure/vacuum lysimeter is being used as an effective vadose zone monitoring device for mining heap leach facilities, tailing disposal ponds and tailing waste sites. Their use has proven reliable for baseline data collection, early warning leakage detection and analyzing geochemical variations in the vadose zone. The lysimeter structure utilizes a closed cylindrical chamber made of PVC or inert material. The soil water intake portion of the cylinder is made of a porous material of low permeability. The application of vacuum or pressure to the unit is via two access tubes from the ground surface. Available soil moisture is drawn by vacuum through porous material into the lysimeter chamber and then collected from the access tubes. Case studies show their usefulness for monitoring around a uranium tailing pond constructed in glacial till material, under heap leach pads and pregnant, barren, and overflow ponds, and investigating the movement of contaminant moisture through old tailing deposits. Relatively easy to install and sample, regulatory agencies and facility operators are accepting and negotiating for their application as a site integrity monitoring device and unsaturated zone research tool. Their use at heap leach facilities lends credibility to solution balance calculations when considering a leachate loss of 5 or 10 percent can make or break a mine's profitability.

Jan 1, 1984

By K. H. E. Kroemer

Selecting persons who are unlikely to suffer an overexertion injury is one of three methods to reduce the risk of musculo-skeletal disorders in manual material handling. This paper describes the underlying models, methods, and techniques for such personnel selection. In particular, it describes the isoinertial LIFTEST in which persons actually lift weights to assess their capability for doing so on the job.

Jan 1, 1985